Page 1
Quick Setup Guide
WARNING
NOTE
DCP-J4110DW
Start Here
Please read the Product Safety Guide first before you set up your machine. Then, please read this Quick Setup
Guide for the correct setup and installation.
WARNING
CAUTION
IMPORTANT
NOTE
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injuries.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injuries.
IMPORTANT indicates a potentially hazardous situation which, if not avoided, may result in
damage to property or loss of product functionality.
Notes tell you how you should respond to a situation that may arise or give tips about how the
operation works with other features.
Unpack the machine and check the components
1
The components included in the box may differ depending on your country.
Black
Yellow
Cyan
Magenta
Starter Ink Cartridges
Quick Setup Guide
Basic User’s Guide Product Safety
Guide
• Plastic bags are used in the packing of your machine. To avoid the danger of suffocation, keep these
plastic bags away from babies and children. Plastic bags are not toys.
• To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is
properly grounded through the standard electrical wiring. Non grounded equipment may cause an
electrical shock hazard, and may cause excessive electrical noise radiation.
• Save all packing materials and the box in case for any reason you must ship your machine.
• For a network connection you will need to purchase a network interface cable. Please use the supplied USB
cable for a USB connection.
USB cable
It is recommended to use a USB 2.0 cable (Type A/B) that is no more than 2 metres long.
Network cable
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast
Ethernet Network.
CD-ROM Power Cord
Cables vary depending on countries.
Taiwan model is using the power cord
attached on the machine.
USB Interface Cable
a Remove the protective tape and film covering the machine, and also from the Touchscreen.
b Make sure you have all the components.
ARL/ASA/NZ/SAF Version 0
1
Page 2
Load plain A4 paper
CAUTION
NOTE
2
DO NOT carry the machine by holding the scanner
cover, the Jam Clear Cover, the manual feed slot
cover, or the control panel. Doing this may cause
the machine to slip out of your hands. Carry the
machine by sliding your hands into the handhold
indentations located on each side of the machine.
For detailed information, see the Product Safety
Guide.
a Pull the paper tray a completely out of the
machine.
c Gently press and slide the paper guides a to fit
the paper size. Make sure that the triangular
mark b on the paper guide a lines up with the
mark for the paper size you are using.
1
2
b Open the output paper tray cover a.
1
1
d Fan the stack of paper well to avoid paper jams
and misfeeds.
Always make sure that the paper is not curled or
wrinkled.
2
Page 3
e Gently put the paper into the paper tray print
IMPORTANT
1
NOTE
side down and top edge first.
Be careful that you do not push the paper in too
far; it may lift at the back of the tray and cause
paper feed problems.
h Slowly push the paper tray completely into the
machine.
i While holding the paper tray in place, pull out
the paper support a until it clicks, and then
unfold the paper support flap b.
2
f Gently adjust the paper guides to fit the paper.
Make sure that the paper guides touch the
edges of the paper.
g Check that the paper is flat in the tray and
below the maximum paper mark a. Close the
output paper tray cover.
1
For printing and copying on special media, open
the manual feed slot a on the back of the
machine. Feed only one sheet at a time of A3,
Ledger, Legal, envelopes, or thicker paper when
using the manual feed slot.
For details, see Loading paper in the manual feed
slot in chapter 2 of the Basic User’s Guide.
1
3
Page 4
Connect the power cord
WARNING
CAUTION
IMPORTANT
NOTE
NOTE
NOTE
NOTE
Install the ink cartridges
3
The machine must be fitted with an earthed
plug.
DO NOT connect the USB cable yet (if you are
using a USB cable).
a Connect the power cord.
5
If ink gets in your eyes, wash it out with water at
once and call a doctor if you are concerned.
Make sure you install the Starter Ink Cartridges
included with your machine first.
a Make sure that the power is turned on.
The Touchscreen will show
No Ink Cartridge.
You can adjust the angle of the control panel by
lifting it. When lowering the control panel, make
sure you push the release button a that is
located behind the mark.
(Example for Australia)
The Warning LED on the control panel will stay on
until you have installed the ink cartridges.
Choose your language
4
a
Press your language
b Press Yes or No.
If you set the wrong language, you can change it
after setting the date and time. (uuAdvanced
User’s Guide: Changing the Touchscreen
language)
.
1
4
Page 5
b Open the ink cartridge cover a.
NOTE
1
IMPORTANT
d Unpack the ink cartridge.
Turn the green release lever on the orange
protective packing a counterclockwise until it
clicks to release the vacuum seal. Then
remove the orange protective packing a as
shown.
c Remove the orange protective part a.
1
Do not throw away the orange protective part.
You will need it if you transport the machine.
2
1
2
1
• DO NOT shake the ink cartridges. If ink stains
your skin or clothing, wash with soap or
detergent at once.
• DO NOT touch the cartridge in the area
indicated b, as this can cause the machine not
to function with the cartridge.
5
Page 6
e Take care to match the sticker colour a with
IMPORTANT
IMPORTANT
the cartridge colour b as shown in the diagram
below.
Install each ink cartridge in the direction of the
arrow on the label.
1
2
f Gently push the back of the ink cartridge
marked “PUSH” until the cartridge lever lifts.
After all the ink cartridges are installed close
the ink cartridge cover.
• DO NOT take out ink cartridges if you do not
need to replace them. If you do so, it may
reduce the ink quantity and the machine will not
know the quantity of ink left in the cartridge.
• DO NOT repeatedly insert and remove the
cartridges. If you do so, ink may seep out of the
cartridge.
• Once you open an ink cartridge, install it in the
machine and use it up within six months of
installation. Use unopened ink cartridges by
the expiration date written on the cartridge
package.
• DO NOT dismantle or tamper with the ink
cartridge, this can cause the ink to leak out of
the cartridge.
• Brother multifunction machines are designed to
work with ink of a particular specification and
will work to a level of optimum performance
when used with genuine Brother branded ink
cartridges. Brother cannot guarantee this
optimum performance if ink or ink cartridges of
other specifications are used. Brother does not
therefore recommend the use of cartridges
other than genuine Brother branded cartridges
with this machine or the refilling of empty
cartridges with ink from other sources. If
damage is caused to the print head or other
parts of this machine as a result of using
incompatible products with this machine, any
repairs required as a result may not be covered
by the warranty.
6
After initial installation of the ink cartridges, the
machine will start cleaning the ink tube system.
This cleaning process will last approximately four
minutes.
DO NOT unplug the machine from the power
outlet or attempt to stop the cleaning process.
Interruption of cleaning process may cause
undesired print quality problems.
Page 7
6
Check the print quality
7
Choose your language (if needed)
a When the preparation process has finished, the
Touchscreen shows Set Paper and Press
Start.
Press Start.
b Check the quality of the four colour blocks on
the sheet. (black/yellow/cyan/magenta)
c If all lines are clear and visible, press Yes to
finish the quality check and go to the next step.
OK
If you can see missing short lines, press No and
follow the steps on the Touchscreen.
Poor
a Press Settings.
b Press s or t to display Initial Setup.
Press Initial Setup.
c Press s or t to display Local Language.
Press Local Language.
d Press your language.
e Press .
Set the date and time
8
Setting the date and time allows the machine to clean
the print head regularly and maintain optimum print
quality. It also allows the machine to name files
created when using the Scan to Media feature.
a Press Settings.
b Press s or t to display Initial Setup.
Press Initial Setup.
c Press Date & Time.
d Press Date & Time.
Enter the last two digits of the year on the
Touchscreen, and then press OK.
To move the cursor to the left, press and
re-enter the number.
(e.g. Enter 1 2 for 2012.)
e Repeat for month/day/time in 24-hour format.
f Press .
7
Page 8
Set the Time Zone
9
You can set the time zone on the machine for your
location.
a Press Settings.
b Press s or t to display Initial Setup.
Press Initial Setup.
c Press Date & Time.
d Press Time Zone.
e Enter your time zone.
Press OK.
f Press .
8
Page 9
Choose your connection type
NOTE
10
These installation instructions are for Windows®XP Home, XP Professional, XP Professional x64 Edition,
Windows Vista
• For Windows Server® 2003/2008/2008 R2, the drivers can be found from your model’s download page at
http://solutions.brother.com/
• If your computer does not have a CD-ROM drive you can download the latest drivers, manuals and utilities
for your model from the Brother Solutions Center at http://solutions.brother.com/
applications included on the CD-ROM may not be available as a download.
• For the latest drivers and information, visit http://solutions.brother.com/
®
, Windows®7, and Mac OS X v10.5.8, 10.6.x, 10.7.x.
.
For USB interface cable
. Some software
.
Windows
Windows®, go to page 10
Macintosh, go to page 13
For Wired Network
Windows®, go to page 16
Macintosh, go to page 20
®
USB Wired Network
Macintosh
Windows
®
Macintosh
Wireless Network
For Wireless Network
Windows® and Macintosh,
go to page 24
9
Page 10
USB
IMPORTANT
NOTE
NOTE
For USB interface users
(Windows®XP Home/XP Professional/Windows Vista®/Windows®7)
b The CD-ROM Top menu will appear.
Before you install
11
Make sure that your computer is ON and you are
logged on with Administrator rights.
• DO NOT connect the USB cable yet.
• If there are any programs running, close them.
Click Install MFL-Pro Suite and click Yes if
you accept the license agreements. Follow the
on-screen instructions.
Windows
®
• The screens may differ depending on your
operating system.
• The CD-ROM includes Nuance™ PaperPort™
®
12SE. This software supports Windows
Home (SP3 or greater), XP Professional (SP3
or greater), XP Professional x64 Edition (SP2
or greater), Windows Vista
and Windows
Windows
MFL-Pro Suite.
®
7. Update to the latest
®
Service Pack before installing
®
(SP2 or greater)
XP
Install MFL-Pro Suite
12
a Put the supplied installation CD-ROM into your
CD-ROM drive. If the model name screen
appears, choose your machine. If the language
screen appears, choose your language.
c Choose Local Connection (USB), and then
click Next. The installation continues.
d When this screen appears, go to the next step.
10
• For Windows Vista® and Windows®7, when
the User Account Control screen appears click
Continue or Yes.
• If the Brother screen does not appear
automatically, go to My Computer or
Computer then double-click the CD-ROM icon
and double-click start.exe.
Page 11
USB
IMPORTANT
IMPORTANT
Connect the USB cable
13
a Lift the scanner cover until it locks securely into
the open position.
Windows
®
c Carefully guide the USB cable into the cable
channel and out the back of the machine.
Connect the cable to your computer.
Windows
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
b Connect the USB cable to the USB port
marked with a symbol a. You will find the
USB port inside the machine on the right, as
shown in the callout below.
1
d Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c using
both hands.
1
3
2
e The installation will continue automatically.
The installation screens appear one after
another.
®
USB
Macintosh
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
11
Page 12
USB
Now go to
NOTE
NOTE
Finish
NOTE
Windows
®
f If Environmental Advice for Imaging
Equipment screen appears, click Next.
g When the On-Line Registration screen is
displayed, follow the on-screen instructions.
Click Next.
h If you do not want to set your machine as the
default printer, uncheck Set as Default Printer
and click Next.
Finish and restart
14
a Click Finish to restart your computer.
After restarting the computer, you must log on
with Administrator rights.
b The following screens will appear.
• When the Software Update Setting screen
appears, choose the software update setting
you want and click OK.
• When the Brother Product Research and
Support Program screen appears, select
your preference and follow the on-screen
instructions.
Internet access is required for the software
update and the Brother Product Research &
Support Program.
The installation is now
complete.
To install optional applications:
• If an error message appears during the
software installation, run the Installation
Diagnostics located in Start/
All Programs/Brother/DCP-JXXX (where
DCP-JXXX is your model name).
• Depending on your security settings, a
Windows
window may appear when using the machine
or its software. Please allow or permit the
window to continue.
®
Security or antivirus software
Page 40
XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is the
most suitable driver for Windows Vista
Windows
use the XML Paper Specification documents.
Please download the latest driver by accessing
the Brother Solutions Center at
http://solutions.brother.com/
®
7 when printing from applications that
.
®
and
12
Page 13
USB
NOTE
IMPORTANT
IMPORTANT
Macintosh
For USB interface users
(Mac OS X v10.5.8, 10.6.x, 10.7.x)
Before you install
11
Make sure your machine is connected to the power
and your Macintosh is ON. You must be logged on
with Administrator rights.
For Mac OS X v10.5.0 to 10.5.7 users, upgrade to
Mac OS X v10.5.8 - 10.7.x.
Connect the USB cable
12
• DO NOT connect the machine to a USB port on
a keyboard or a non-powered USB hub.
• Connect the machine directly to your
Macintosh.
b Connect the USB cable to the USB port
marked with a symbol a. You will find the
USB port inside the machine on the right, as
shown in the callout below.
1
c Carefully guide the USB cable into the cable
channel and out the back of the machine.
Connect the cable to your Macintosh.
Windows
®
USB
Macintosh
a Lift the scanner cover until it locks securely into
the open position.
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
13
Page 14
USB
Macintosh
d Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c using
both hands.
1
3
2
Install MFL-Pro Suite
13
e Choose your machine from the list, and then
click OK.
f When this screen appears, click Add Printer.
Choose your machine from the list. Click Add
and then click Next.
a Put the supplied installation CD-ROM into your
CD-ROM drive.
b Double-click the Start Here OSX icon to install.
If the model name screen appears, choose
your machine.
c Choose Local Connection (USB), and then
click Next. Follow the on-screen instructions.
g When this screen appears, click Next.
The installation of MFL-Pro Suite is now
complete.
Go to step 14.
d Please wait for the software to install. After the
installation, the Brother software will search for
the Brother device. This will take a few
moments to complete.
14
Page 15
USB
Finish
Download and install
14
When Presto! PageManager is installed, OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a On the Brother Support screen, click the
Presto! PageManager
Presto! PageManager to go to the
Presto! PageManager download site, and
follow the on-screen instructions.
Macintosh
Windows
The installation is now
complete.
®
USB
Macintosh
15
Page 16
Wired Network
IMPORTANT
NOTE
For wired network interface users
(Windows®XP Home/XP Professional/Windows Vista®/Windows®7)
Windows
®
Before you install
11
Make sure that your computer is ON and you are
logged on with Administrator rights.
If there are any programs running, close them.
• The screens may differ depending on your
operating system.
• The CD-ROM includes Nuance™ PaperPort™
12SE. This software supports Windows
Home (SP3 or greater), XP Professional (SP3
or greater), XP Professional x64 Edition (SP2
or greater), Windows Vista
and Windows
Windows
MFL-Pro Suite.
• If you have previously set up your machine for
a wireless network and then want to set it up on
a wired network, you should check that the
machine’s Network I/F is set to
Wired LAN. The wireless network interface
will become inactive with this setting.
On your machine, press Settings.
Press s or t to display Network.
Press Network.
Press s or t to display Network I/F.
Press Network I/F.
Press Wired LAN.
®
7. Update to the latest
®
Service Pack before installing
®
(SP2 or greater)
®
XP
Connect the network
12
cable
a Lift the scanner cover until it locks securely into
the open position.
b Connect the network cable to the Ethernet port
marked with a symbol a. You will find the
Ethernet port inside the machine on the left, as
shown in the callout below. Remove the orange
protective cap before connecting the cable.
1
16
Press .
Page 17
Wired Network
IMPORTANT
NOTE
NOTE
c Carefully guide the network cable into the cable
channel and out the back of the machine.
Connect the cable to your network.
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
Windows
®
Install MFL-Pro Suite
13
a Put the supplied installation CD-ROM into your
CD-ROM drive. If the model name screen
appears, choose your machine. If the language
screen appears, choose your language.
• For Windows Vista® and Windows®7, when
the User Account Control screen appears click
Continue or Yes.
• If the Brother screen does not appear
automatically, go to My Computer or
Computer then double-click the CD-ROM icon
and double-click start.exe.
If both the USB and the network cables are being
used, guide both cables through the cable
channel with one on top of the other.
d Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c using
both hands.
1
3
2
b The CD-ROM Top menu will appear.
Click Install MFL-Pro Suite and click Yes if
you accept the license agreements. Follow the
on-screen instructions.
Windows
Wired Network
®
Macintosh
17
Page 18
Wired Network
NOTE
IMPORTANT
NOTE
c Choose Wired Network Connection
(Ethernet), and then click Next.
d When this screen appears, choose Change
the Firewall port settings to enable network
connection and continue with the
installation. (Recommended) and click Next.
Windows
®
• If there is more than one machine connected to
the network, choose your machine from the list,
and then click Next.
This window will not appear if there is only one
machine connected to the network, the
machine will be chosen automatically.
• If your machine is not found over the network,
the following screen will appear.
If you are using a firewall other than the
Windows
off, this screen may appear.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
For network scanning, add UDP port 54925.
If you still have trouble with your network
®
Firewall or the Windows® Firewall is
connection, add UDP ports 137 and 161.
Confirm your settings by following the
on-screen instructions.
e The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
For Windows Vista® and Windows®7, when the
®
Windows
check box and click Install to complete the
installation correctly.
Security screen appears, click the
18
f If Environmental Advice for Imaging
Equipment screen appears, click Next.
g When the On-Line Registration screen is
displayed, follow the on-screen instructions.
Click Next.
h If you do not want to set your machine as the
default printer, uncheck Set as Default Printer
and click Next.
Page 19
14
Now go to
NOTE
NOTE
NOTE
Finish
NOTE
Wired Network
Finish and restart
15
Windows
®
Install MFL-Pro Suite on additional computers (if needed)
a Click Finish to restart your computer. After
restarting the computer, you must log on with
Administrator rights.
• If an error message appears during the
software installation, run the Installation
Diagnostics located in Start/
All Programs/Brother/DCP-JXXX (where
DCP-JXXX is your model name).
• Depending on your security settings, a
Windows
window may appear when using the machine
or its software. Please allow or permit the
window to continue.
®
Security or antivirus software
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 13 on page 17. Also see
step 11 on page 16 before you install.
Network license (Windows®)
This product includes a PC license for up to 2
users. This license supports the installation of the
MFL-Pro Suite including Nuance™ PaperPort™
12SE on up to 2 PCs on the network. If you want
to use more than 2 PCs with Nuance™
PaperPort™ 12SE installed, please purchase the
Brother NL-5 pack which is a multiple PC license
agreement pack for up to 5 additional users. To
purchase the NL-5 pack, contact Brother
customer service or your local Brother dealer.
The installation is now
complete.
To install optional applications:
Windows
b The following screens will appear.
• When the Software Update Setting screen
appears, choose the software update setting
you want and click OK.
• When the Brother Product Research and
Support Program screen appears, select
your preference and follow the on-screen
instructions.
Internet access is required for the software
update and the Brother Product Research &
Support Program.
Page 40
XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is the
most suitable driver for Windows Vista
®
Windows
use the XML Paper Specification documents.
Please download the latest driver by accessing
the Brother Solutions Center at
http://solutions.brother.com/
7 when printing from applications that
.
®
and
Wired Network
®
Macintosh
19
Page 20
Wired Network
NOTE
Macintosh
For wired network interface users
Before you install
11
Make sure your machine is connected to the power
and your Macintosh is ON. You must be logged on
with Administrator rights.
• For Mac OS X v10.5.0 to 10.5.7 users, upgrade
to Mac OS X v10.5.8 - 10.7.x.
• If you have previously set up your machine for
a wireless network and then want to set it up on
a wired network, you should check that the
machine’s Network I/F is set to
Wired LAN. The wireless network interface
will become inactive with this setting.
On your machine, press Settings.
Press s or t to display Network.
Press Network.
Press s or t to display Network I/F.
Press Network I/F.
Press Wired LAN.
Press .
(Mac OS X v10.5.8, 10.6.x, 10.7.x)
Connect the network
12
cable
a Lift the scanner cover until it locks securely into
the open position.
b Connect the network cable to the Ethernet port
marked with a symbol a. You will find the
Ethernet port inside the machine on the left, as
shown in the callout below. Remove the orange
protective cap before connecting the cable.
1
20
Page 21
Wired Network
IMPORTANT
NOTE
c Carefully guide the network cable into the cable
channel and out the back of the machine.
Connect the cable to your network.
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
Macintosh
Install MFL-Pro Suite
13
a Put the supplied installation CD-ROM into your
CD-ROM drive.
b Double-click the Start Here OSX icon to install.
If the model name screen appears, choose
your machine.
If both the USB and the network cables are being
used, guide both cables through the cable
channel with one on top of the other.
d Lift the scanner cover to release the lock a.
Gently push the scanner cover support
down b and close the scanner cover c using
both hands.
1
3
2
c Choose Wired Network Connection
(Ethernet), and then click Next. Follow the
on-screen instructions.
d Please wait for the software to install. After the
installation, the Brother software will search for
the Brother device. This will take a few
moments to complete.
e If the machine is configured for your network,
choose your machine from the list, and then
click OK.
Windows
Wired Network
®
Macintosh
21
Page 22
Wired Network
NOTE
• If your machine is not found over the network,
confirm your network settings.
• You can find your machine’s MAC Address
(Ethernet Address) and IP Address by printing
out the Network Configuration Report.
uuNetwork User’s Guide: Printing the Network
Configuration Report
• If this screen appears, click OK.
Enter a name for your Macintosh up to
15 characters long.
Macintosh
f When this screen appears, click Add Printer.
Choose your machine from the list. Click Add
and then click Next.
If you want to use the scan feature directly from
your machine to scan over the network, you
must check the Register your computer with
the “Scan To” function on the machine box.
Click OK. Go to f.
The name you enter will appear on the
machine’s Touchscreen when you press Scan
and choose a scan option. (uuSoftware User’s
Guide: Network Scanning)
g When this screen appears, click Next.
The installation of MFL-Pro Suite is now
complete.
Go to step 14.
22
Page 23
Wired Network
Finish
Download and install
14
When Presto! PageManager is installed, OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a On the Brother Support screen, click the
Presto! PageManager
Presto! PageManager to go to the
Presto! PageManager download site, and
follow the on-screen instructions.
Macintosh
Install MFL-Pro Suite on
additional computers
15
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 13 on page 21. Also see
step 11 on page 20 before you install.
(if needed)
The installation is now
complete.
Windows
Wired Network
®
Macintosh
23
Page 24
For Wireless Network Users
NOTE
NOTE
For wireless network interface users
Before you begin
11
First you must configure the wireless network settings of your machine to communicate with your access
point/router. After the machine is configured to communicate with your access point/router, computers on your
network will have access to the machine. To use the machine from these computers, you will need to install the
drivers and software. The following steps will guide you through the configuration and installation process.
To achieve optimum results with normal everyday document printing, place the Brother machine as close to the
network access point/router as possible with minimal obstructions. Large objects and walls between the two
devices as well as interference from other electronic devices can affect the data transfer speed of your documents.
Due to these factors, wireless may not be the best method of connection for all types of documents and
applications. If you are printing large files, such as multi-page documents with mixed text and large graphics, you
may want to consider choosing wired Ethernet for a faster data transfer or USB for the fastest throughput speed.
Although your Brother machine can be used in both a wired and wireless network, only one of the connection
methods can be used at a time.
If you have previously configured the wireless settings of the machine you must reset the network settings
before you can configure the wireless settings again.
On your machine, press Settings.
Press s or t to display Network. Press Network.
Press s or t to display Network Reset. Press Network Reset.
Press Yes to accept. Hold down Yes for 2 seconds to confirm.
The following instructions are for infrastructure mode (connected to a computer through an access point/router).
Infrastructure Mode
1
4
2
3
a Access point/router
b Wireless network machine (your machine) connected to the access point/router
c Wireless-capable computer connected to the access point/router
d Wired computer connected to the access point/router
e Mobile device connected to the access point/router
Please make sure the wireless network settings of the machine match the access point/router.
5
24
To set up your machine in Ad-hoc mode (connected to a wireless-capable computer without an access
point/router) you can find instructions in the Network User’s Guide on the CD-ROM.
You can view the Network User’s Guide by following the instructions below.
1 Turn on your computer. Insert the CD-ROM into your CD-ROM drive.
For Windows
2 Choose your model and the language. The CD-ROM top menu will appear.
3 Click User’s Guides, and then click PDF documents.
4 Click Network User’s Guide.
For Macintosh:
2 Double-click User’s Guides. Choose your model and the language.
3 Click User’s Guides, and then click Network User’s Guide.
®
:
Page 25
For Wireless Network Users
NOTE
Now go to
Choose your wireless setup method
12
The following instructions offer three methods for setting up your Brother machine on a wireless network. Choose
the method you prefer for your environment.
a Setup using the installation CD-ROM and a USB cable (Windows
You need to temporarily use a USB cable during configuration.
It is recommended that you use a computer wirelessly connected to your network for this method.
• If you are using Windows® XP, or currently using a computer connected to an access
point/router by network cable, you need to know your wireless settings. Please write down
your wireless network settings in the area below.
• Please do not contact Brother Customer Service for assistance without the wireless security
information. We cannot assist you in locating your network security settings.
Item Record the current wireless network settings
SSID (Network Name)
Network Key
* The Network Key may also be described as the Password, Security Key or Encryption Key.
®
and Macintosh)
If you do not know this information (SSID and Network Key), you cannot continue the wireless
setup.
How can I find this information?
1) You should see the documentation provided with your wireless access point/router.
2) The initial network name could be the manufacturer’s name or the model name.
3) If you do not know the security information, please consult the router manufacturer, your system
administrator or internet provider.
page 27
Wireless Network
25
Page 26
For Wireless Network Users
NOTE
Now go to
Now go to
For methods b and c, start your wireless setup by pressing the Wi-Fi button on the Touchscreen.
b Manual setup from the control panel using the Setup Wizard (Windows
mobile devices)
If your wireless access point/router does not support WPS (Wi-Fi Protected Setup™) or AOSS™,
write down the wireless network settings of your wireless access point/router in the area below.
Please do not contact Brother Customer Service for assistance without the wireless security
information. We cannot assist you in locating your network security settings.
Item Record the current wireless network settings
SSID (Network Name)
Network Key
* The Network Key may also be described as the Password, Security Key or Encryption Key.
If you do not know this information (SSID and Network Key), you cannot continue the wireless
setup.
How can I find this information?
1) You should see the documentation provided with your wireless access point/router.
2) The initial SSID could be the manufacturer’s name or the model name.
3) If you do not know the security information, please consult the router manufacturer, your system
administrator or internet provider.
®
, Macintosh and
page 30
One-push setup using WPS or AOSS™ (Windows®, Macintosh and mobile devices)
c
If your wireless access point/router supports automatic wireless (one-push) setup (WPS or AOSS™)
page 31
26
Page 27
For Wireless Network Users
NOTE
Setup using the
installation CD-ROM and
13
a USB cable (Windows
®
and Macintosh)
• You need to temporarily use a USB cable
during configuration.
• These steps are for a Windows
For Macintosh installation, insert the
installation CD-ROM into your CD-ROM
drive and double-click Start Here OSX to
install. Select Wireless installation and
follow the Wireless Device Setup
instructions on your computer screen.
®
installation.
a Put the supplied installation CD-ROM into your
CD-ROM drive. If the model name screen
appears, choose your machine. If the language
screen appears, choose your language.
c Choose Wireless Network Connection, and
then click Next.
d When this screen appears, choose Change
the Firewall port settings to enable network
connection and continue with the
installation. (Recommended) and click Next.
• For Windows Vista® and Windows®7, when
the User Account Control screen appears click
Continue or Yes.
• If the Brother screen does not appear
automatically, go to My Computer or
Computer then double-click the CD-ROM icon
and double-click start.exe.
b The CD-ROM Top menu will appear.
Click Install MFL-Pro Suite and click Yes if
you accept the license agreements. Follow the
on-screen instructions.
If you are using a firewall other than the
Windows
off, this screen may appear.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
For network scanning, add UDP port 54925.
If you still have trouble with your network
®
Firewall or the Windows® Firewall is
connection, add UDP ports 137 and 161.
Wireless Network
27
Page 28
For Wireless Network Users
NOTE
NOTE
e Choose Yes, I have a USB cable to use for
installation. and then click Next.
f Temporarily connect the USB cable directly to
the computer and the machine.
If the confirmation screen appears, check the
box and click Next, go to g.
Otherwise, go to h.
g When the following screen appears, check Yes
if you want to connect to the listed SSID. Click
Next and go to j.
h When the following screen appears, the wizard
will search for wireless networks available to
your machine. Choose the SSID that you wrote
down for your network in step 12-a on
page 25, and then click Next.
• For instructions on connecting the USB cable
to the USB port of your machine, see Connect
the USB cable on page 11.
• If this screen appears, read the Important
Notice. Check the box after you confirm the
SSID and Network Key, and then click Next.
• If a list of SSIDs is not displayed, make sure
your access point is on and set to broadcast the
SSID. Make sure the machine and the access
point are within communication range, then
click Refresh.
• If your access point is set to not broadcast the
SSID you can manually add it by clicking the
Advanced button. Follow the on-screen
instructions for entering the Name (SSID), and
then click Next.
28
Page 29
For Wireless Network Users
Now go to
Now go to
NOTE
NOTE
i Enter the Network Key you wrote down in
step 12-a on page 25, and then click Next.
If your network is not configured for
Authentication and Encryption, the following
screen will appear. To continue configuration,
click OK and go to j.
k Disconnect the USB cable between the
computer and the machine.
l Click Next to continue to install MFL-Pro Suite.
Wireless setup is now complete. The
Wi-Fi button at the upper right of the
Touchscreen changes to a four-level
indicator that displays the wireless signal
strength of your access point/router.
The Wi-Fi LED on the control panel
lights up, indicating that the machine’s
Network I/F is set to WLAN.
To install MFL-Pro Suite
j Click Next. The settings will be sent to your
machine.
• The settings will remain unchanged if you click
Cancel.
• If you want to manually enter the IP address
settings of your machine, click Change IP
Address and enter the necessary IP address
settings for your network.
• If the wireless setup failure screen appears,
click Retry.
For Windows® users:
Step 15-e on page 35
For Macintosh users:
Step 15-d on page 37
Wireless Network
29
Page 30
For Wireless Network Users
Now go to
Now go to
NOTE
NOTE
Manual setup from the
control panel using the
13
Setup Wizard
®
(Windows
, Macintosh
and mobile devices)
a Press .
Press Setup Wizard.
When Network I/F switched to
Wireless. is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
b The machine will search for available SSIDs. It
will take several seconds to display a list of
available SSIDs.
If a list of SSIDs is displayed, press s or t to
choose the SSID you wrote down in step 12-b
on page 26. Select the SSID you want to
connect with.
d Enter the Network Key you wrote down in
step 12-b on page 26 using the Touchscreen.
The letters appear in this order: lower case and
then upper case. Press to cycle between
letters, numbers and special characters. (The
characters available may differ depending on
your country.) To move the cursor to the right,
press c.
(For more information, see Entering Text for
Wireless Settings on page 41.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings.
e Your machine will now try to connect to your
wireless network. It may take a few minutes.
f A connection result message appears for
60 seconds on the Touchscreen and a WLAN
report will automatically be printed.
If the connection failed, check the error code on
the printed report and refer to Troubleshooting
on page 32.
If the wireless access point/router of the
selected SSID supports WPS and the machine
asks to use WPS, go to c.
If the machine asks you to enter a Network
Key, go to d.
Otherwise, go to e.
• If a list of SSIDs is not displayed, make sure
your access point is on. Move your machine
closer to the access point and try starting
from a again.
• If your access point is set to not broadcast the
SSID, you will have to manually add the SSID
name. For details, see the Network User’s
Guide.
c Press Yes to connect your machine using
WPS. (If you choose No to continue manual
configuration, go to d to enter a Network Key.)
When the Touchscreen indicates you should
start WPS, press the WPS button on your
wireless access point/router, and then press
Next to proceed.
Go to e.
Wireless setup is now complete. The
Wi-Fi button at the upper right of the
Touchscreen changes to a four-level
indicator that displays the wireless signal
strength of your access point/router.
The Wi-Fi LED on the control panel
lights up, indicating that the machine’s
Network I/F is set to WLAN.
For Mobile Device users, please go to the User’s
Guide for the application you are using (Eg.
AirPrint, Brother iPrint&Scan or other
applications) for additional details on how to use
your machine with the application. To download
the User’s Guide for the application you are using,
please go to the manuals download selection on
your model’s home page of the Brother Solutions
Center at http://solutions.brother.com/
.
To install MFL-Pro Suite, continue to
step 14.
For Windows® users:
Page 34
For Macintosh users:
Page 37
30
Page 31
For Wireless Network Users
Now go to
Now go to
NOTE
NOTE
One-push setup using
WPS or AOSS™
13
(Windows
®
, Macintosh
and mobile devices)
a Confirm your wireless access point/router has
the WPS or AOSS™ symbol as shown below.
b Place the Brother machine within range of your
WPS or AOSS™ access point/router. The
range may differ depending on your
environment. Refer to the instructions provided
with your access point/router.
c Press .
Press s or t to display WPS/AOSS.
Press WPS/AOSS.
When Network I/F switched to
Wireless. is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
e A connection result message appears for
60 seconds on the Touchscreen and a WLAN
report will automatically be printed.
If the connection failed, check the error code on
the printed report and refer to Troubleshooting
on page 32.
Wireless setup is now complete. The
Wi-Fi button at the upper right of the
Touchscreen changes to a four-level
indicator that displays the wireless signal
strength of your access point/router.
The Wi-Fi LED on the control panel
lights up, indicating that the machine’s
Network I/F is set to WLAN.
For Mobile Device users, please go to the User’s
Guide for the application you are using (Eg.
AirPrint, Brother iPrint&Scan or other
applications) for additional details on how to use
your machine with the application. To download
the User’s Guide for the application you are using,
please go to the manuals download selection on
your model’s home page of the Brother Solutions
Center at http://solutions.brother.com/
.
If your wireless access point/router supports WPS
(PIN Method), you can also configure your
machine using the PIN (Personal Identification
Number) Method. uuNetwork User’s Guide:
Configuration using the PIN Method of WPS
(Wi-Fi Protected Setup)
d When the Touchscreen indicates you should
start WPS or AOSS™, press the WPS or
AOSS™ button on your wireless access
point/router. See the user’s guide of your
wireless access point/router for instructions.
Then press OK and your machine will now
automatically detect which mode (WPS or
AOSS™) your wireless access point/router
uses and try to connect to your wireless
network.
To install MFL-Pro Suite, continue to
step 14.
For Windows® users:
Page 34
For Macintosh users:
Page 37
Wireless Network
31
Page 32
For Wireless Network Users
Troubleshooting
Please do not contact Brother Customer Service for assistance without the wireless security
information. We cannot assist you in locating your network security settings.
How can I find the wireless security information (SSID and Network Key)
1) You should see the documentation provided with your wireless access point/router.
2) The initial SSID could be the manufacturer’s name or the model name.
3) If you do not know the security information, please consult the router manufacturer, your system
administrator or internet provider.
* The Network Key may also be described as the Password, Security Key or Encryption Key.
Wireless LAN report
If the wireless LAN report that printed shows that the connection failed, check the error code on the printed report
and refer to the following instructions.
Error code Recommended Solutions
The wireless setting is not activated, turn the wireless setting to ON.
- If a network cable is connected to your machine, disconnect it and turn the wireless setting
of your machine to ON.
TS-01
TS-02
On your machine, press Settings.
Press s or t to display Network, and then press Network.
Press s or t to display Network I/F, and then press Network I/F.
Press WLAN.
Press .
The wireless access point/router cannot be detected.
1. Check the following 4 points.
- Make sure that the wireless access point/router is powered on.
- Move your machine to an obstruction-free area, or closer to the wireless access
point/router.
- Temporarily place your machine within about one metre from the wireless access point
when you are configuring the wireless settings.
- If your wireless access point/router is using MAC address filtering, confirm the MAC
address of the Brother machine is allowed in the filter.
2. If you manually entered the SSID and security information (SSID/authentication
method/encryption method/Network Key), the information may be incorrect.
Reconfirm the SSID and security information and re-enter the correct information as
necessary.
32
See How can I find the wireless security information (SSID and Network Key) on page 32 to
confirm.
Page 33
TS-04
For Wireless Network Users
The Authentication/Encryption methods used by the selected wireless access point/router are
not supported by your machine.
For infrastructure mode, change the authentication and encryption methods of the wireless
access point/router.
Your machine supports the following authentication methods:
authentication method encryption method
WPA-Personal
WPA2-Personal AES
Open
Shared key WEP
If your problem is not solved, the SSID or network settings you entered may be incorrect.
Reconfirm the wireless network settings.
See How can I find the wireless security information (SSID and Network Key) on page 32 to
confirm.
None (without encryption)
TKIP
AES
WEP
TS-05
TS-06
TS-07
For ad-hoc mode, change the authentication and encryption methods of your computer for
the wireless setting.
Your machine supports Open authentication method only, with optional WEP encryption.
The security information (SSID/Network Key) is incorrect.
Reconfirm the SSID and security information (Network Key).
If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother
machine supports the use of the first WEP key only.
See How can I find the wireless security information (SSID and Network Key) on page 32 to
confirm.
The wireless security information (Authentication method/Encryption method/Network Key) is
incorrect.
Reconfirm the wireless security information (Authentication method/Encryption method/
Network Key) in the table of TS-04.
If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother
machine supports the use of the first WEP key only.
See How can I find the wireless security information (SSID and Network Key) on page 32 to
confirm.
The machine cannot detect a wireless access point/router that has WPS or AOSS™ enabled.
If you would like to configure your wireless settings using WPS or AOSS™, you must operate
both your machine and the wireless access point/router.
Confirm your wireless access point/router supports WPS or AOSS™ and try starting again.
If you do not know how to operate your wireless access point/router
using WPS or AOSS™ see the documentation provided with your
wireless access point/router, ask the manufacturer of your wireless
access point/router or ask your network administrator.
Wireless Network
TS-08
Two or more wireless access points that have WPS or AOSS™ enabled are detected.
- Confirm that only one wireless access point/router within range has the WPS or AOSS™
method active and try again.
- Try starting again after a few minutes in order to avoid interference from other access
points.
33
Page 34
Wireless Network
IMPORTANT
NOTE
NOTE
Install the drivers & software
(Windows®XP Home/XP Professional/Windows Vista®/Windows®7)
b The CD-ROM Top menu will appear.
Before you install
14
Make sure that your computer is ON and you are
logged on with Administrator rights.
If there are any programs running, close them.
• The screens may differ depending on your
operating system.
• The CD-ROM includes Nuance™ PaperPort™
12SE. This software supports Windows
Home (SP3 or greater), XP Professional (SP3
or greater), XP Professional x64 Edition (SP2
or greater), Windows Vista
and Windows
Windows
MFL-Pro Suite.
®
7. Update to the latest
®
Service Pack before installing
®
(SP2 or greater)
®
XP
Click Install MFL-Pro Suite and click Yes if
you accept the license agreements. Follow the
on-screen instructions.
c Choose Wireless Network Connection, and
then click Next.
Windows
®
Install MFL-Pro Suite
15
a Put the supplied installation CD-ROM into your
CD-ROM drive. If the model name screen
appears, choose your machine. If the language
screen appears, choose your language.
• For Windows Vista® and Windows®7, when
the User Account Control screen appears click
Continue or Yes.
• If the Brother screen does not appear
automatically, go to My Computer or
Computer then double-click the CD-ROM icon
and double-click start.exe.
34
Page 35
Wireless Network
NOTE
IMPORTANT
NOTE
Windows
®
d When this screen appears, choose Change
the Firewall port settings to enable network
connection and continue with the
installation. (Recommended) and click Next.
If you are using a firewall other than the
Windows
off, this screen may appear.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
For network scanning, add UDP port 54925.
If you still have trouble with your network
®
Firewall or the Windows® Firewall is
connection, add UDP ports 137 and 161.
f The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
For Windows Vista® and Windows®7, when the
®
Windows
check box and click Install to complete the
installation correctly.
Security screen appears, click the
g If Environmental Advice for Imaging
Equipment screen appears, click Next.
h When the On-Line Registration screen is
displayed, follow the on-screen instructions.
Click Next.
i If you do not want to set your machine as the
default printer, uncheck Set as Default Printer
and click Next.
e Choose your machine from the list, and then
click Next.
• If your machine is not found over the network,
confirm your settings by following the
on-screen instructions. If you encounter this
failure, go to step 12-b on page 26 and setup
the wireless connection again.
• If you are using WEP and the Touchscreen
displayed Connected but your machine is not
found on the network, make sure you entered
the WEP key correctly. The WEP key is case
sensitive.
Windows
Wireless Network
®
Macintosh
35
Page 36
16
Now go to
NOTE
NOTE
NOTE
Finish
NOTE
Wireless Network
Finish and restart
17
Windows
®
Install MFL-Pro Suite on additional computers (if needed)
a Click Finish to restart your computer. After
restarting the computer, you must log on with
Administrator rights.
• If an error message appears during the
software installation, run the Installation
Diagnostics located in Start/
All Programs/Brother/DCP-JXXX (where
DCP-JXXX is your model name).
• Depending on your security settings, a
Windows
window may appear when using the machine
or its software. Please allow or permit the
window to continue.
®
Security or antivirus software
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 14 on page 34.
Network license (Windows®)
This product includes a PC license for up to 2
users. This license supports the installation of the
MFL-Pro Suite including Nuance™ PaperPort™
12SE on up to 2 PCs on the network. If you want
to use more than 2 PCs with Nuance™
PaperPort™ 12SE installed, please purchase the
Brother NL-5 pack which is a multiple PC license
agreement pack for up to 5 additional users. To
purchase the NL-5 pack, contact Brother
customer service or your local Brother dealer.
The installation is now
complete.
To install optional applications:
b The following screens will appear.
• When the Software Update Setting screen
appears, choose the software update setting
you want and click OK.
• When the Brother Product Research and
Support Program screen appears, select
your preference and follow the on-screen
instructions.
Internet access is required for the software
update and the Brother Product Research &
Support Program.
Page 40
XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is the
most suitable driver for Windows Vista
®
Windows
use the XML Paper Specification documents.
Please download the latest driver by accessing
the Brother Solutions Center at
http://solutions.brother.com/
7 when printing from applications that
.
®
and
36
Page 37
Wireless Network
NOTE
NOTE
Macintosh
Install the drivers & software
(Mac OS X v10.5.8, 10.6.x, 10.7.x)
Before you install
14
Make sure your machine is connected to the power
and your Macintosh is ON. You must be logged on
with Administrator rights.
For Mac OS X v10.5.0 to 10.5.7 users, upgrade to
Mac OS X v10.5.8 - 10.7.x.
Install MFL-Pro Suite
15
a Put the supplied installation CD-ROM into your
CD-ROM drive.
d Choose your machine from the list, and then
click Next.
If your wireless settings fail, the Wireless Device
Setup Wizard screen appears. Follow the
on-screen instructions to complete the wireless
configuration.
b Double-click the Start Here OSX icon to install.
If the model name screen appears, choose
your machine.
c Choose Wireless Network Connection, and
then click Next.
e Choose your machine from the list, and then
click OK.
Windows
Wireless Network
®
Macintosh
37
Page 38
Wireless Network
NOTE
Macintosh
f The installation of the Brother drivers will
automatically start. Please wait for the software
to install.
• You can find your machine’s MAC Address
(Ethernet Address) and IP Address by printing
out the Network Configuration Report.
uuNetwork User’s Guide: Printing the Network
Configuration Report
• If this screen appears, click OK.
Enter a name for your Macintosh up to
15 characters long.
g When this screen appears, click Add Printer.
Choose your machine from the list. Click Add
and then click Next.
h When this screen appears, click Next.
If you want to use the scan feature directly from
your machine to scan over the network, you
must check the Register your computer with
the “Scan To” function on the machine box.
Click OK. Go to g.
The name you enter will appear on the
machine’s Touchscreen when you press Scan
and choose a scan option. (uuSoftware User’s
Guide: Network Scanning)
The installation of MFL-Pro Suite is now
complete.
Go to step 16.
38
Page 39
Wireless Network
Finish
Download and install
16
When Presto! PageManager is installed, OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a On the Brother Support screen, click the
Presto! PageManager
Presto! PageManager to go to the
Presto! PageManager download site, and
follow the on-screen instructions.
Macintosh
Install MFL-Pro Suite on
additional computers
17
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 14 on page 37.
(if needed)
The installation is now
complete.
Windows
Wireless Network
®
Macintosh
39
Page 40
Install Optional Applications
NOTE
NOTE
NOTE
Windows
®
Install optional
1
FaceFilter Studio and BookScan &
Whiteboard Suite supported by
Reallusion, Inc
FaceFilter Studio is an easy-to-use borderless photo
printing application.
The BookScan Enhancer software can correct your
scanned book images automatically.
The Whiteboard Enhancer software cleans up and
enhances text and images from photos taken of your
whiteboard.
• The machine must be ON and connected to the
computer.
• Some applications require Internet access.
• Make sure you are logged on with
Administrator rights.
• This application is not available for Windows
Server
applications
®
2003/2008 series.
Install FaceFilter Studio
2
To get instructions on how to use FaceFilter Studio,
download and install FaceFilter Studio Help.
Help
a To run FaceFilter Studio, go to
Start/All Programs/Reallusion/
FaceFilter Studio on your computer.
b Click Check for Updates on the screen.
You can also go to the Reallusion update web
page by clicking the button in the upper right
corner of this screen.
a Open the top menu again by ejecting and then
reinserting the CD-ROM or by double-clicking
the start.exe program from the root folder.
b The CD-ROM Top menu will appear. Choose
your language and then click Additional
Applications.
c Click the button for the application you want to
install.
c Click the Download button and choose a folder
to save the file in.
d Close FaceFilter Studio before you start the
installer for FaceFilter Studio Help.
Double-click the downloaded file from the
folder you specified and follow the on-screen
instructions for installation.
To view the complete FaceFilter Studio Help, go
to Start/All Programs/Reallusion/
FaceFilter Studio/FaceFilter Studio Help on
your computer.
d Go back to the Additional Applications
screen to install more applications.
40
Page 41
For Network Users
Reset the network settings to factory default
To restore all network settings of the internal Print/Scan server to the factory default, please follow the steps below.
a Make sure the machine is idle, then disconnect all the cables from the machine (except the power cord).
b Press Settings.
c Press s or t to display Network, and then press Network.
d Press s or t to display Network Reset, and then press Network Reset.
e Press Yes.
f Hold down Yes for 2 seconds to confirm.
g The machine will restart, re-connect the cables once this is complete.
Entering Text for Wireless Settings
Up to four letters are assigned to each letter button on the Touchscreen. By pressing the correct button repeatedly,
you can access the character you want.
Press to cycle between letters, numbers and special characters. (The characters available may differ
depending on your country.)
Inserting spaces
To enter a space, press then press the space button or .
Repeating characters
If you need to enter a character that is on the same button as the character before, press c to move the cursor to
the right.
Making corrections
If you entered a character incorrectly and want to change it, press to delete it and re-enter the correct
character.
41
Page 42
Consumables
Replacement consumables
When the time comes to replace ink cartridges, an error message will be indicated on the Touchscreen. For more
information about the ink cartridges for your machine, visit http://www.brother.com/original/
Brother re-seller.
Ink cartridge
Magenta Cyan Yellow Black
LC133M (High Yield)
LC135XLM
(Super High Yield)
What is Innobella™?
Innobella™ is a range of genuine consumables offered by Brother.
The name “Innobella™” derives from the words “Innovation” and “Bella” (meaning
“Beautiful” in Italian) and is a representation of the “innovative” technology providing you
with “beautiful” and “long lasting” print results.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a trademark of Brother Industries, Ltd.
Windows, Windows Vista and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the United States and other countries.
Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates
in the United States and/or other countries.
FaceFilter Studio is a trademark of Reallusion, Inc.
AOSS is a trademark of Buffalo Inc.
Wi-Fi and Wi-Fi Protected Access (WPA) are registered trademarks of the Wi-Fi Alliance.
Wi-Fi Protected Setup and Wi-Fi Protected Access 2 (WPA2) are trademarks of the Wi-Fi A lliance.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.
Any trade names and product names of companies appearing on Brother products, related documents and any other
materials are all trademarks or registered trademarks of those respective companies.
Compilation and Publication
Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and
specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for
any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other
errors relating to the publication.
Copyright and License
©2012 Brother Industries, Ltd. All rights reserved.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC. ALL RIGHTS RESERVED.
©2008 Devicescape Software, Inc. All rights reserved.
This product includes the “KASAGO TCP/IP” software developed by ZUKEN ELMIC,Inc.
LC133C (High Yield)
LC135XLC
(Super High Yield)
LC133Y (High Yield)
LC135XLY
(Super High Yield)
or contact your local
LC133BK (High Yield)
LC137XLBK
(Super High Yield)
Get inspired. If you’re using Windows®, double-click the Brother CreativeCentre icon on your desktop to
access our FREE website with many ideas and resources for personal and professional use.
Mac users can access Brother CreativeCentre at this web address: http://www.brother.com/creativecenter/
www.brotherearth.com
Loading...