Broan QP236BC Installation

QP2 SERIES

Register your product online

at: www.broan.com

EVOLUTIONTM 2

READ AND SAVE THESE INSTRUCTIONS

FOR DOMESTIC COOKING ONLY

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN­JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac­turer. If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the ser­vice disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.

3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction.

4. Sufficient air is needed for proper combustion and exhaust­ing of gases through the flue (chimney) of fuel burning equip­ment to prevent backdrafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code au­thorities.

5. This product may have sharp edges. Be careful to avoid cuts
and abrasions during installation and cleaning.

6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.

7. Ducted fans must always be vented

8. Use only metal ductwork.

9. Do not use this fan with any solid-state speed control device.

10. As an alternative, this product may be installed with the UL­approved cord kit designated for the product, following in­structions packed with the cord kit.

11. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ig­nite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when
flambéing food (i.e. Crêpes Suzette, Cherries Jubilee, Pep­percorn Beef Flambé).

3. Clean ventilating fans frequently. Grease should not be al­lowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for
the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,
or metal t ray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.

the outdoors.

to

WARNING

2. NEVER PICK UP A FLAMING PAN — Yo u may be burned or
spread the fire.

3. DO NOT USE WATER, including wet dishcloths or towels - a
violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher, and you

already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.

* Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION

1. F o r indoor use only.

2. For general ventilating use only. Do not use to exhaust haz­ardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbal­anced impeller, keep drywall spray, construction dust, etc.,
off power unit.

4. Do not use over cooking equipment greater than 60,000
BTU/hr. as the blower motor will shut down intermittently.

5. Your hood motor has a thermal overload which will automati­cally shut off the motor if it becomes overheated. The motor
will restart when it cools down. If the motor continues to shut
off and restart, have the hood serviced.

6. The top of the hood MUST NOT BE LESS than 24” and at a
maximum of 30” above
impurities.

7. This hood is not intended to be used as a shelf.

8. Please read specification label on product for further infor­mation and requirements.

NOTE If hood is to be installed non-ducted:
Purchase a set of (2) non-ducted filters for 30” wide

hoods (Model BPPF30) & 36” wide hoods (Model
BPPF36) or a set of (3) non-ducted filters for 42” wide
hoods (Model BPPF42) from your local distributor or
retailer and attach them to the aluminum mesh filters.

Installer: Leave this manual

with the homeowner.

Homeowner: Cleaning, Maintenance and

Operating instructions on pages 2 & 3.

cookt

op for best capture of cooking

Page 1

OPERATION

Always turn the hood ON before cooking in order to establish an
air flow in the kitchen. After turning off the range, let the hood run
for a few minutes to clear the air.

Operate the hood as follows:

LIGHT (3 push-button switches)

FUSE

FUSE

QP2 SERIES

Page 2

RANGE HOOD CONTROL BOARD

Turns light on to LOW setting.

Turns light on to MEDIUM setting.

Turns light on to HIGH setting.

Pressing the same light button again will turn lights OFF.
A light above each button indicates light setting.

FAN (3 push-button switches)

Turns fan on to LOW speed.

Turns fan on to MEDIUM speed.

Turns fan on to HIGH speed.

Pressing the same fan button again will turn fan OFF.
A light above each button indicates fan speed.

NOTE

This hood utilizes an offset blower design to achieve greater
performance and lower sound levels. As a result, you may notice
that cooking impurities are more attracted to one side or appear
to be pulled-in faster than they appear on the opposite side. This
is completely normal. The hood has been designed and tested
to provide good capture of cooking impurities and odors under
all normal cooking conditions regardless of the cooking location
on the cooktop. Please note that cooking on the rear burners will
always result in the best capture of cooking impurities, regardless
of the hood design.

HEAT SENTRY SYSTEM

This range hood is equipped with an advanced Heat Sentry sys­tem that monitors for excessive temperature and automatically
adjusts the fan to the appropriate setting.

1) If the fan is on, the Heat Sentry system will increase the fan
setting when the temperature is elevated. If the temperature con­tinues to rise, the Heat Sentry system will continue to increase
the fan setting until the temperature is stabilized or reduced. The
flashing light above the fan button shows the Heat Sentry system
fan setting. Once the temperature has reduced, the Heat Sentry
system will change the fan to the original setting.

2) If the fan is off, (CANADIAN VERSION DOES NOT HAVE
THIS FUNCTION) the Heat Sentry system will automatically turn
the fan on to its highest speed when the temperature is above
normal. When the Heat Sentry system is on, the light above the
high speed fan button will flash on and off. After the temperature
has lowered to normal, the fan speed will be reduced until the
temperature has stabilized, then the fan will turn off.

The Range Hood Control Board contains a Fuse to protect the
controls from power surges. If the fuse has opened (blown), the
green fan setting or light setting indicators will not operate properly
when the fan or light buttons are pressed, and the fan and lights
will not turn on.

A new fuse can be purchased at your local electronic supply
store. Use an 8A, 120V, 5 mm diameter, 20 mm long, fast-acting,
cartridge-type fuse.

To replace the fuse (by qualified person(s):

1. Disconnect power at service entrance.

2. Remove filters and bottom pan.

3. Remove and inspect fuse. If it is not open (blown), additional

diagnostics are needed.

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper per­formance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the motor with the exact service motor. The impeller should also
be replaced.

Grease Filter

The grease filters should be cleaned frequently. Use a warm dish­washing detergent solution. Grease filters are dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filters may occur if using phosphate
detergents, or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered by
the warranty.

See Step 9 on page 5 for removal and installation instructions.

Non-ducted Recirculation Filter

The non-ducted recirculation filter should be changed every 6
months. Replace more often if your cooking style generates extra
grease, such as frying and wok cooking. The special “Clean Sense”
feature indicates when the filter is to be replaced. The dotted lines
on the indicator strip will change to solid wide lines when it is time
to change the filter. The “Clean Sense” feature works best when
facing toward the cooking surface. See Step 15 on page 5, for
removal and

installation instructions.

Stainless Steel Cleaning

DO:

• Regularly wash with clean cloth or rag soaked with warm water
and mild soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after cleaning.
Wipe dry completely.

• You may also use a specialized household stainless steel cleaner.

DON’T:

Use any steel or stainless steel wool or any other scrapers to re-

•
move stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues reach the
hood. During construction/renovation, cover the range hood to
make sure no dust sticks to the stainless steel surface.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing chloride, fluoride, iodide, bromide
will deteriorate surfaces rapidly.

• Any combustible products used for cleaning, such as ac­etone, alcohol, ether, benzol, etc. are highly explosive and
should never be used close to a range.

QP2 SERIES

Page 3

LAMP SOCKET

BRACKET

LIGHT

PANEL

To change the depth of bulb sockets:

- Remove bottom pan (See Step 10).

- Remove 2 Light Panel Screws and Light Panel. Set

screws aside.

- Loosen 2 Screws holding Lamp Socket Bracket to
Light Panel.

- Adjust socket/bracket to desired depth.

- Re-tighten screws securely.

- Re-attach light panel and bottom pan.

SCREWS

LIGHT BULB REPLACEMENT

SUCTION

CUP TOOL

HALOGEN

BULB

(2)

ROTATE

CLOCKWISE

LIGHT PANEL

SCREWS

CAUTION: Bulbs may be hot. Always allow bulbs
to cool down before removing them.

This hood uses (4) Halogen Bulbs (included with hood). Use 120
V, 50W, shielded halogen bulbs - MR16 with GU10 base.

NOTE: Suction Cup Tool (included with hood) can be used to
install and remove light bulbs.

Align pins on bulb with large diameter opening on socket, then
push bulb in towards hood and rotate clockwise until firmly seated.

The position of the bulb socket (depth) is adjustable and may
require adjustment when:

a) certain brands of bulbs are difficult to install.
b) the bulb protrudes too far below the light panel.

(1)

PUSH IN

LIGHT PANEL

INSTALL THE DUCTWORK
(Ducted Hoods Only)

ROOF CAP

SOFFIT

CABINET

HOODHOOD

24" - 30" ABOVE
COOKING SURFACE

1 Determine whether hood will discharge vertically (3¼” x

10” or 7” Round), or horizontally (3¼” x 10” only).

2 Decide where the ductwork will run between the hood

and the outside.

3 Choose a straight, short duct run to allow the hood to

perform most efficiently. Long duct runs, elbows and
transitions will reduce the performance of the hood. Use
as few of them as possible. Larger ductwork may be
required for best performance with longer duct runs.

4 Install wall cap or roof cap. Connect metal ductwork to

cap and work back towards the hood location. Use duct
tape to seal the joints between ductwork sections.

3¼" X 10" or

7" ROUND DUCT

(For vertical

discharge)

HOUSE WIRING
(Top or Back of hood)

WALL CAP

3¼" X 10" DUCT
(For horizontal discharge)

QP2 SERIES

VERTICAL DUCT

ACCESS HOLE

¾"

10

7

/

8

"

5¼"

5¼"

CENTER

LINE

HOOD MOUNTING SCREWS (5)

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

WOOD SHIMS

(recessed-bottom

cabinets only)

CABINET FRONT

CABINET
BOTTOM

17

5

/

8

" (42" hood)

4½"

2

1

/

8

"

2

5

/

8

"

11"

6

7

/

8

"

*

17

5

/

8

" (42" hood)

14

5

/

8

" (36" hood)14

5

/

8

" (36" hood)

11

5

/

8

" (30" hood)11

5

/

8

" (30" hood)

Page 4

PREPARE HOOD LOCATION

5 Use the proper diagram below, for placement of ductwork

and electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole.

3¼” X 10”

VERTICAL DUCTING

WOOD SHIMS

(recessed-bottom

cabinets only)

HORIZONTAL DUCTING

CABINET FRONT

3¼” X 10”

13/8"

3

/8"

MEASURE THE INSTALLATION

ROOF CAP

SOFFIT

CABINET

HOODHOOD

24" - 30" ABOVE
COOKING SURFACE

6 The minimum hood distance above cooking surface

MUST NOT BE LESS than 24” (to top of hood).

A maximum of 30” above cooking surface is highly

recommended for best capture of cooking impurities.

Distances over 30” are at the installer’s and user’s

discretion; providing that the cabinet height permits.

3¼" X 10" or

7" ROUND DUCT

(For vertical

discharge)

HOUSE WIRING
(Top or Back of hood)

WALL CAP

3¼" X 10" DUCT
(For horizontal discharge)

CONTENTS

CABINET

4"

BOTTOM

5

/

" (30" hood)

8

5

/

" (36" hood)

8

5

/

" (42" hood)

8

HOOD

MOUNTING

SCREWS (5)

HOOD MOUNTING SCREWS (5)

5

/

" (30" hood)

8

5

/

" (36" hood)

8

5

/

" (42" hood)

8

45/8"

8" DIA.

HOLE

Note the extra wood shim and mounting screw near the

*

cabinet front, on the cabinet center line.

HORIZONTAL DUCT

*

ACCESS HOLE

5¼"

CENTER

LINE

5

/

11

8

5

/

14

8

5

/

17

8

*

7-IN. ROUND

7-IN. ROUND

6

DUCT

DUCT

ACCESS

ACCESS

HOLE

HOLE

7/8"

5¼"

67/8"

5

/

" (30" hood)11

11

8

5

/

14

" (36" hood)14

8

5

/

17

" (42" hood)17

8

ELECTRICAL

ACCESS HOLE

(in wall)

" (30" hood)11

" (36" hood)14
" (42" hood)17

11"

21/8"

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

7-IN. ROUND

DUCTING

7

/8"

10

5

2

/8"

INCLUDED WITH THE HOOD:

GREASE

FILTERS

(2 - FOR 30” & 36” HOODS)

3 - FOR 42” HOODS)

(4)

HALOGEN

BULBS

(1) PARTS BAG CONTAINING:

(3)
WIRE
NUTS

(9)

#8 X 1/4”

DUCT

CONNECTOR

SCREWS

(1)

BULB

SUCTION

CUP TOOL

(5)

#10 X 5/8”

RD. HD.

MOUNTING

SCREWS

(1) 3¼” X 10”

DAMPER / DUCT

CONNECTOR

(1) 7” ROUND

DUCT

CONNECTOR

(1)

NON-DUCT

DIVERTER

(2)
#8 X 5/16”
MACHINE
SCREWS

&

(2)

#8 WASHERS

FOR NON-DUCT

DIVERTER

QP2 SERIES

Page 5

PREPARE THE HOOD

7 Remove parts bag

from the hardware
box included with
the hood.

8 Remove all

protective polyfilm
from the hood
(stainless steel
hoods only).

9 Remove the

Aluminum Filters
from the hood.

10 Remove 6 Screws holding Bottom Pan to hood. Set bot-

tom pan and screws aside.

(2)
LIFT
OUT

ç

ç

(1)

PULL

DOWN

ALUMINUM

FILTERS

SLOT

ç

NON-DUCT

PLENUM

NON-DUCT

PLATE

SCREWS

NON-DUCT

PLATE

DAMPER /

DUCT CONNECTOR

11 Remove 2 Screws holding Damper / Duct Connector

to hood. Remove damper/duct connector from inside the
hood.

FOR DUCTED INSTALLATIONS - Skip to Step 16.

NON-DUCT

DIVERTER

12 NON-DUCTED INSTALLATION ONLY:

From parts bag: Attach Non-Duct Diverter to Air Box
with 2 Screws and 2 Washers.

13 NON-DUCTED INSTALLATION ONLY:

Remove 2 Screws holding Non-Duct Plate to Non-Duct
Plenum and remove plate.

SCREWS

NON-DUCT

PLATE

14 NON-DUCTED INSTALLATION ONLY:

Insert short end of Non-Duct Plate into Non-Duct
Plenum Slot. Attach with 2 Screws removed in Step 13.

15 NON-DUCTED INSTALLATION ONLY:

Purchase a set of (2) non-ducted filters for 30” wide hoods
(Model BPPF30) & 36” wide hoods (Model BPPF36) or
a set of (3) non-ducted filters for 42” wide hoods (Model
BPPF42) from your local distributor or retailer. Attach the
non-ducted filters to the aluminum mesh filters following
instructions packed with the non-ducted filters.

FOR NON-DUCTED INSTALLATIONS - Skip to
“INSTALL THE HOOD”.

QP2 SERIES

Page 6

7” ROUND

KNOCKOUT

PLATE (also

remove 3¼” x 10”

vertical plate)

VERTICAL

KNOCKOUT

3¼” X 10”

HORIZONTAL

KNOCKOUT

PLATE

16 DUCTED INSTALLATION ONLY:

Remove 3¼” x 10 vertical, 3¼” x 10” horizontal, or 7-inch
round knockout plate(s) as appropriate for your ducting
method.

3¼” X 10”

DAMPER /

DUCT

CONNECTOR

TOP/BACK

EDGE OF

HOOD

3¼” X 10”

PLATE

DAMPER

FLAP

PIVOT

INSTALL THE HOOD

WARNING

To reduce the risk of electrical shock, switch power off
at service panel. Lock or tag service panel to prevent
power from being switched on accidentally.

ELECTRICAL

WIRING BOX

COVER

ELECTRICAL

POWER

CABLE

KNOCKOUT

18 Remove Electrical Wiring Box Cover from inside

of hood and appropriate Electrical Power Cable
Knockout from top or back of hood.

7” ROUND

DUCT

PLATE

17 DUCTED INSTALLATION ONLY:

Attach 3¼” x 10” Damper/Duct Connector (if using 3¼”
x 10” duct) or 7” Round Duct Plate (if using 7-inch round
duct) over the knockout opening.

Notes:

To accomodate off-center ductwork, the 3¼” x 10”
damper/duct connector can be installed up to ½” on either
side of the hood center and the 7” round duct plate can
be installed up to ½” on either side of the hood center.

Install the 3¼” x 10” Damper/Duct Connector with the

Damper Flap Pivot nearest the Top/Back Edge of
Hood.

HOUSE

POWER CABLE

19 Run House Power Cable between service panel and hood

location. Attach power cable to hood using appropriate clamp.

20 Hang hood from (4) mounting screws driven part-way into

cabinet locations (shown in illustrations under “PREPARE
HOOD LOCATION”). Mounting screws are included in parts
bag. Slide hood back towards wall until mounting screw
heads are engaged in narrow end of keyhole slots in top of
hood. Tighten screws securely. Add 5th mounting screw in
center hole in hood and tighten securely.

21 DUCTED INSTALLATION ONLY:

Connect ductwork to hood and use duct tape to make joints
secure and air-tight. Make sure the damper / duct connector
enters the ductwork and that the damper opens and closes
freely.

QP2 SERIES

Page 7

CONNECT THE WIRING

GROUND

SCREW

HOUSE

POWER CABLE

22 Connect House Power Cable to range hood wiring -

BLACK to BLACK, WHITE to WHITE, and GREEN or
BARE WIRE to Ground Screw. Replace electrical wiring
box cover.

23 Re-attach Bottom Pan with 6 Screws removed in Step 10.

24 DUCTED INSTALLATION ONLY:

Re-install aluminum filters removed in Step 9.

NON-DUCTED INSTALLATION ONLY:

Install aluminum filters and non-ducted filters - purchased
and assembled in Step 15.

WARRANTY

One Year Limited Warranty

Broan-NuTone warrants to the original consumer purchaser
of its products that such products will be free from defects
in materials or workmanship for a period of one (1) year
from the date of original purchase. THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.

During this one year period, Broan-NuTone will, at its
option, repair or replace, without charge, any product or
part which is found to be defective under normal use and
service. THIS WARRANTY DOES NOT EXTEND TO
FLUORESCENT LAMP STARTERS, TUBES, HALOGEN
AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS,
ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES
FOR DUCTING. This warranty does not cover (a) normal
maintenance and service or (b) any products or parts which
have been subject to misuse, negligence, accident, improper
maintenance or repair (other than by Broan-NuTone),
faulty installation or installation contrary to recommended
installation instructions.

The duration of any implied warranty is limited to the one year
period as specified for the express warranty. Some states do
not allow limitation on how long an implied warranty lasts, so
the above limitation may not apply to you.

BROAN-NUTONE’S
REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER
THIS WARRANTY. BROAN-NUTONE SHALL NOT BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states do not
allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply
to you. This warranty gives you specific legal rights, and you
may also have other rights, which vary from state to state.
This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan­NuTone at the address or telephone number below, (b) give
the model number and part identification and (c) describe
the nature of any defect in the product or part. At the time of
requesting warranty service, you must present evidence of
the original purchase date.

Broan-NuTone LLC, 926 W. State Street,
Hartford, Wisconsin 53027
www.broan.com 800-558-1711

Broan-NuTone Canada, Inc., 1140 Tristar Drive,
Mississauga, Ontario Canada L5T 1H9
www.broan.ca 877-896-1119

OBLIGATION TO REP

AIR OR

SERVICE PARTS

QP2 SERIES

Page 8

15

12

11

1

16

10

14

3

2

9

17

4

13

8

6

7

KEY NO. PART NO. DESCRIPTION

1 97017727 7” Round Duct Plate (includes mounting hardware)
2 97018245 User Interface Assembly White (includes interface, nameplate, mounting hardware)
97018246 User Interface Assembly Black (includes interface, nameplate, mounting hardware)
97018247 User Interface Assembly Bisque (includes interface, nameplate, mounting hardware)
3 99528248 Nameplate, White
99528249 Nameplate, Black
99528250 Nameplate, Bisque
4 97018251 Capacitor Kit (includes wire nuts, mounting screw)
5 97018225 Light Panel RH White (includes mounting hardware)
97018226 Light Panel RH Black (includes mounting hardware)
97018227 Light Panel RH Stainless (includes mounting hardware)
97018228 Light Panel RH Bisque (includes mounting hardware)
6 97018202 Filter Kit for 30”” (2 per bag)
97018203 Filter Kit for 36” (2 per bag)
97018204 Filter Kit for 42” (3 per bag)
7 97018220 Blower Wheel (includes mounting nut)
8 97018719 Motor Kit (includes motor, isolators, mounting hardware)
9 97017728 Damper / Duct Connector (includes mounting hardware)
10 97018229 Light Panel LH White (includes mounting hardware)
97018230 Light Panel LH Black (includes mounting hardware)
97018231 Light Panel LH Stainless (includes mounting hardware)
97018232 Light Panel LH Bisque (includes mounting hardware)
11 97017731 Lamp Socket (includes lamp socket, wire nuts, mounting screws)
12 97018233 Lamp Socket Bracket
13 97018236 Bottom Pan 30” (includes mounting hardware)
97018237 Bottom Pan 36” (includes mounting hardware)
97018238 Bottom Pan 42” (includes mounting hardware)
14 97018242 Non-duct Plenum (includes gasket & mounting hardware)
15 97018243 Non-duct Diverter (includes mounting hardware)
16 97018244 Non-duct Plate (includes mounting hardware)
17 97018254 Circuit Board (U.S. models)
97018661 Circuit Board (Canadian models)
Not Shown 97018224 Parts Bag
Not Shown 99010353 Non-Duct Filter Kit for 30”” (2 charcoal filters and 8 filter clips)
99010354 Non-Duct Filter Kit for 36” (2 charcoal filters and 8 filter clips)
99010360 Non-Duct Filter Kit for 42” (3 charcoal filters and 12 filter clips)
Not Shown 99526707 Suction Cup Tool
Not Shown 97018252 Heat Sensor (U.S. models only)
Not Shown 97018253 Fuse
Not Shown 97018255 Ribbon Cable
Not Shown V05921 50W Halogen GU10 Bulb

5

Order replacement parts by
PART NO. - not by KEY NO.

99527290F