MODELS 331H & 332H
EXTERIOR MOUNTED
BLOWER
FOR USE WITH RANGEMASTER HOODS AND ECLIPSE DOWNDRAFT VENTILATORS
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in
the warranty.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
a qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction
codes and standards.
4. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall, or ceiling, do not
damage electrical wiring or other hidden utilities.
WARNING
6. Ducted fans must always be vented to the outdoors.
7. To reduce risk of fire, use only metal ductwork.
8. This unit must be grounded.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive material and vapors.
2. To avoid motor bearing damage and noisy and/or
unbalanced impellers, keep drywall spray, construction
dust, etc. off power unit.
3. Please read specification label on product for further
information and requirements.
4. Electrical circuit, including speed control, (if used),
must be rated 6 AMPS minimum for Model 332H or 3
AMPS minimum for Model 331H.
Important-when using Model 332H with the Broan
Eclipse Downdraft Models 2830-A or 2836-A: Purchase a #97011927 Speed Control Kit from your
Broan distributor to replace the speed control in
your downdraft.
SPECIFICATIONS
MODEL VOLTS AMPS CFM DUCT SIZE
331H 120 2.4 600 10 " DIA.
332H 120 5.7 900 10" DIA.
PLAN THE INSTALLATION
ALL INSTALLATIONS
1. Locate the blower so the length of the duct run and
number of elbows and transitions needed are kept to a
minimum.
Please note - when using blower with the Broan
Eclipse Downdraft: The downdraft has a 3¼" x 10"
discharge. Transitions are available to connect it to
the 10" round inlet on this exterior-mounted blower.
2. Where possible, blower should be centered between
wall studs or roof rafters.
INSTALLER: Leave This Manual With The Homeowner
HOMEOWNER: Use And Care Information On Page 3
PLAN THE INSTALLATION
3. Avoid pipes, wires, or other ductwork that may be
running through the wall.
4. Be sure that there is enough space for any transitions
that may be needed between the blower and the
connecting ductwork.
5. For best performance, locate transitions nearest to
ventilator (i.e. downdraft).
PREPARE THE INSTALLATION
LOCATION
ROOF INSTALLATIONS
PREPARE THE INSTALLATION
LOCATION
WALL INSTALLATIONS
1. Locate the blower on the rear slope of the roof.
Place it in a location to minimize duct run. The
location should be free of obstacles (T.V. leads,
electrical lines, etc.). Bear in mind, if the blower top
is level with the roof peak, it will not be seen from
the street. Keep this approximate location in mind
as you work from within the attic.
2. Mark a point halfway between rafters.
3. Drill a guide hole through the roof at this point.
Figure 1
20-3/4"
8-1/2"
10-3/8"
20-1/2"
7-1/4"
1-1/4" Dia. Hole
11" Dia.
Hole
Guide
Hole
9-1/8"
4. From the outside, use the guide hole as a starting
point and mark the rectangular cutout and
remove
only the shingles in this area. See Figure 1.
5. Mark an 11" diameter circle centered on the guide
hole and mark the center of the 1-1/4" diameter
electrical wiring hole. See Figure 1.
1. Choose a position on the outside wall. Make sure
that no wall studs, pipes or wires run through the
opening area.
2. Drill a guide hole at the center of the opening area.
Figure 3
10-3/4"
12-7/8"
29-1/2"
1-1/4" Dia. Hole
25"
11" Dia.
Hole
Guide
Hole
9-1/8"
7-1/4"
3. Mark a 25" by 29-1/2" rectangle on wall located
from guide hole as shown in Figure 3.
4.
Cut a rectangular hole in the siding only. Do not cut
the sheathing. Nail down all siding ends.
5. Mark an 11" diameter circle centered on the guide
hole and mark the center of the 1-1/4" diameter
electrical wiring hole.
6. Cut the 11" diameter hole in the sheathing and drill
the 1-1/4" hole as marked.
6. Cut out the roof board(s) along the 11" diameter
circle and drill a 1-1/4" hole as marked.
Figure 2
29-1/2"
2"
7"
25"
2"
7. For flat roof installations, build a curb that will
mount the blower at a minimum pitch of 2/12. See
Figure 2. Discharge end of the blower should be
pointed away from prevailing winds.
PREPARE THE BLOWER
ALL INSTALLATIONS
1. Unpack the blower assembly.
2. Remove the cover and screws.
3. Remove and discard cardboard from blower wheel.
4. Remove the wiring box cover and screws.
5. Attach an appropriate U.L. approved cable connector in the hole at the rear of the wiring box.
INSTALL THE BLOWER
INSTALL THE BLOWER
ROOF INSTALLATIONS
1. Remove roofing nails from the upper 2/3 of the
shingles around the cutout area and carefully lift the
shingles to allow the back flashing sheet on the
blower housing to fit under them.
2.Center the blower ring in the 11" diameter hole,
making sure that the 1-1/4" diameter electrical
wiring hole aligns with the hole in the wiring box.
3.Attach the blower to the roof with the six screws
provided. All six holes in the back panel must be
filled, or any moisture that may get inside the
housing could leak into the house.
4.Using a good grade of roofing cement, seal all of the
shingles around the housing and flashing sheet as
well as the mounting screw heads.
5.Bring electrical wiring through the hole in the wiring
box and secure it according to local codes.
Figure 4
WALL INSTALLATIONS
1. Place a large bead of caulk on the back side of the
housing along the outer edge.
2. Center the blower ring in the 11" diameter hole,
making sure that the 1-1/4" diameter electrical
wiring hole aligns with the hole in the wiring box.
3. Attach blower to the wall with the six screws
provided. All six holes in the back panel must be
filled, or any moisture that may get inside the
housing could leak into the house.
4. Using a good grade of caulk, seal all around the
mounting screw heads.
5. Bring electrical wiring through the hole in the wiring
box and secure it according to local codes.
6. Make the electrical connections with the proper
connector for the type of wire being used. Connect
white to white, black to black, and green or bare
wire to green. See Figure 4.
BLACK
TO
BLACK
120 VAC
LINE IN
WHITE
TO
WHITE
GREEN
TO
GREEN
6. Make the electrical connections with the proper
connector for the type of wiring being used. Connect white to white, black to black, and the green or
bare wire to green. See Figure 4.
7.Replace wiring box cover and screws. Do not pinch
wiring under the cover.
7. Replace wiring box cover and screws. Do not
pinch wiring under cover.
8. Check for free movement of the damper before
installing housing cover and screws.
9. Turn on power and check operation of the blower.
10.Top and side flanges of the back plate may be
covered with trim strips. Do not block grille opening
at bottom with trim. It will adversely affect performance of the blower.
USE AND CARE
Disconnect electrical power supply and lock out service panel before cleaning or servicing this unit.
CLEANING
Remove cover and carefully vacuum blower and
inside of housing. Be careful not to bend or otherwise
damage blower wheel.
8. Check for free movement of the damper before
installing housing cover and screws.
9.Turn on power and check operation of the blower.
MOTOR LUBRICATION
The motor is permanently lubricated. Do not oil or
disassemble motor.
SERVICE PARTS
MODELS 332H & 331H
16
13
12
KEY
NO. PART NO. DESCRIPTION
1 97011795 Airbox Assembly
2 98008507 Damper
3 93260454 Sheet Metal Nut, #18-18 U-Type (7 req.)*
4 99100484 Isolator (3 req.)
5 99260477 Whiz Nut, 1/4" - 20 (3 req.)*
6 98008511 Grille
7 99100379 Heyco Damper (2 req.)
8 99080396 Motor W/Capacitor (Model 332)
99080397 Motor W/Capacitor (Model 331)
10 98008509 Wiring Box Cover
11 98008588 Capacitor Clamp
12 98008510 Airbox Cover
13 99020263 Blower Wheel (Model 332)
99020264 Blower Wheel (Model 331)
14 99140145 Damper Spring
15 99400055 Heyco
16 99100517 Foam Seal (4 req.)
17 99150471 Hex Screw, #10 - 32 x 1/2"*
18 99150535 Hex Screw, #8-16 x 3/8 (2 Req.)*
19 99271110 Capacitor 15 MFD
* Standard Hardware - May be purchased locally.
Always order replacement parts by Part No., not Key No.
6
4
3
5
1
4
8
5
15
11
17
14
18
19
7
2
10
18
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its
products that such products will be free from defects in materials or
workmanship for a period of one year from the date of original
purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair
or replace, without charge, any product or part which is found to be
defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT
LAMP STARTERS AND TUBES. This warranty does not cover (a)
normal maintenance and service or (b) any products or parts which
have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation
or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year
period as specified for the express warranty. Some states do not
allow limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT
BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF
OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may
not apply to you.
This warranty gives you specific legal rights, and you may also have
other rights, which vary from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone
at the address stated below or telephone: 1-800-637-1453, (b) give
the model number and part identification and (c) describe the nature
of any defect in the product or part. At the time of requesting
warranty service, you must present evidence of the original purchase date.
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027
(1-800-637-1453)
NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227
(1-800-543-8687)
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)
NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 (1-888-882-7626)
99043017A
Loading...