Broan 273602C, 273001C, 273023C, 273003, 273603 Specifications
MODELS 2730 & 2736
TM
ECLIPSE
DOWNDRAFT
BLOWER SYSTEM
SPECIFICATION SHEET
Exhaust your cooktop without the use of an
overhead hood.
FEATURES
HOUSING:
• Rugged steel construction
• Black paint and/or galvanized finish
• Space-saving - can be used with most cooktops on the
market
• 30" or 36" size - Fits standard-size cabinets
• For indoor use only
BLOWER:
• Dynamically-balanced 9-1/8" dia. x 2-1/8" centrifugal blower
wheel for quiet, efficient performance
• Permanently lubricated, thermally-protected motor
• Neoprene, resilient anti-vibration mounts
• Unit plugs directly into 120 VAC, 60 HZ, grounded outlet
• Uses standard 3-1/4" x 10" duct connector
• 3-position discharge - scroll box moveable to adjust to
floor joists
AIR VENT ASSEMBLY:
• Brushed stainless steel cover - just press button to turn
unit "ON"
• Designer White or Black doors - available separately
• Air vent rises to 7" from cooktop for optimum removal of
cooking contaminants
• Two washable aluminum grease filters
• Stainless steel face plate - makes cleanup quick and easy
• Flush-mounted, infinite speed blower control
• Conveniently located button - press to lower air vent and
turn unit "OFF"
TYPICAL SPECIFICATION
Downdraft blower system shall be Broan Model 2730 (Broan
Model 2736).
Unit to have steel housing with electrically coated acrylic paint
or galvanized finish. Air vent to rise at least 7" and have a
stainless steel face plate for ease of cleaning.
Filters to be washable and removable from above.
Blower will connect directly to 3-1/4" x 10" rectangular duct
(6" round duct using a transition). Blower discharge to be
convertible to accommodate ductwork from LEFT, RIGHT,
or BELOW and have 7-1/2" side-to-side adjustment.
Motor shall be mounted to blower assembly with grease
resistant anti-vibration mounts, be removable, and lifetime
lubricated.
Downdraft system shall operate on 120 VAC and be able to
be plugged into a standard grounded outlet. It will have an
infinite speed blower control.
Air delivery shall be no less than 500 CFM. Air delivery rating shall be certified by HVI. Downdraft blower system to be
U.L. listed.
SPECIFICATIONS
VOLTS HZ AMPS CFM DUCT
120 60 4.0 500 3-1/4" x 10"
HVI-2100 CERTIFIED RATINGS comply with
new testing technologies and procedures
prescribed by the Home Ventilating Institute,
for off-the-shelf products, as they are available
to consumers. Product performance is rated
at 0.1 in. static pressure, based on tests
conducted in a state-of-the-art test laboratory.
Sones are a measure of humanly-perceived
loudness, based on laboratory measurements.
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
Broan-NuTone Canada Mississauga, Ontario www.broan.ca 877-896-1119
REFERENCE QTY. REMARKS Project
Location
Architect
Engineer
Contractor
Submitted by Date
11L 99041819E
INSTALLATION PLANNING - MODELS 2730 & 2736
DIMENSIONS
NOTE: Dimensions shown are for reference only. Before cutting out
countertop, refer to instructions packed with downdraft and cooktop.
DOWNDRAFT
A
COUNTER TOP
COOKTOP
FRONT TO BACK
INSIDE CABINET DEPTH
Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. The
2730 and 2736 can be installed in most standard 30" and 36"
wide cabinets.
Cooktop depth can vary greatly from one to another. This may
cause the fit of these two appliances to be rather tight.
Pay special attention to the 4 areas of potential interference highlighted above. The back of the downdraft cut-out will be 1-3/4" from
the cooktop and 2" of FLAT countertop is needed behind cooktop.
1 3/4 "
2"
B
DOWNDRAFT
TYPICAL INSTALLATION
COUNTER
CABINET
FRONT
TOP
COOK TOP
GEAR
MOTOR
COVER
BLOWER
BOX
3-1/4" X 10"
DUCT CONNECTOR
CHIMNEY TOP
AIR
VENT
120 VAC
GOUNDED
OUTLET
ELECTRICAL
The unit has a 2 ft. power cord with a 3-pronged plug. Plan to
provide a grounded outlet within reach of this cord. Outlet may
also be wall-mounted, with access hole in cabinet. If local codes
call for hard-wiring, see installation instructions.
DUCTWORK
This downdraft blower system is designed for use with 3-1/4" x
10" rectangular, or 6" round duct. The blower discharge can be
positioned in one of 3 directions with 7-1/2" movement side to side.
RIGHT
DISCHARGE
LEFT
DISCHARGE
2 FT.
3-1/4" X 10"
90o ELBOW
3-1/4" x 10" TO
6" RD.
TRANSITION
The system will operate most efficiently when the ductwork does
not exceed 40 feet of equivalent duct. The chart above, shows
equivalent feet of elbows and transitions. The number of feet of
straight 3-1/4" x 10" or 6" duct plus the equivalent feet of elbows
or transitions to be used should equal 40 feet or less.
DOWN
DISCHARGE
(as shipped)
6" RD.
ELBOW
8 FT.
6 FT.
The equivalent feet of various roof and wall caps has been taken
into consideration. Do not include them in this calculation.
Loading...