Breville BEM820SHB, BEM820BKS User Manual

the Scraper Mixer Twin™

Instruction Booklet

Suits model BEM820

(Combination BEM800 mixer with small bowl)

CONGRATULATIONS

on the purchase of your new Breville product

PAge heAder.....CONTENTS

4 Breville recommends safety ﬁrst

8 Know your Breville product

11 Assembly & operation

18 Care, cleaning and storage

20 Measuring and weighing

23 Hints and tips

29 Troubleshooting

31 Recipes

PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST

We design and manufacture our products with your safety foremost in mind. We ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

• Carefully read all

instructions before operating the bench mixer for the ﬁrst time and save for future reference.

• Remove and safely discard

any packaging material and promotional labels before using the bench mixer for the ﬁrst time.

• To eliminate a choking

hazard for young children, remove and safely discard the protective cover ﬁtted to the power plug of this appliance.

• Do not place the bench mixer

near the edge of a bench or table during operation. Ensure the surface is level, clean and free of water and other substances. Vibration during operation may cause the appliance to move.

• Do not use the bench mixer

on a sink drain board.

• Do not place the bench

mixer on or near a hot gas or electric burner, or where it could touch a heated oven.

• Always ensure the bench

mixer is completely assembled before operating. Follow the instructions provided in this book.

• Ensure the speed control

dial is in the OFF position and the bench mixer is switched off at the power outlet and the power cord is unplugged before attaching the beater, whisk or dough hook.

• Do not use attachments other

than those provided with the bench mixer. Use only the beater whisk and dough hook supplied with the mixer.

PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST

• The maximum dough this

machine can mix is 600 grams ﬂour plus 375ml water. If your recipe is more than this, machine must be rested after 3 minutes of use to avoid overloading the motor.

• Do not operate the appliance

continuously on heavy loads for more than 3 minutes. None of the recipes in this book are considered a heavy load.

• Maximum load for the small

bowl is 125g butter, softened and chopped, with 3/4 cup caster sugar. Always make sure your butter is softened before creaming. Do not use cold butter.

• Handle the bench mixer and

attachments with care. Never place your ﬁngers inside the mixing bowl or near the beater, whisk or dough hook during operation.

• Keep hands, hair, clothing,

as well as, spatulas and other utensils away from moving beater, whisk or dough hook/ during operation.

• Should an object such as a

spoon or spatula fall into the bowl while mixing,

immediately ensure the speed control dial is in the OFF position, turn the bench mixer off, unplug at the power outlet and remove the object.

• Do not place hands in the

mixing bowl unless the bench mixer is disconnected from the power outlet. Ensure the speed control dial is in the OFF position, the bench mixer is switched off and unplugged from the power outlet before removing the beater, whisk or dough hook.

• Ensure the motor and beater,

whisk or dough hook have completely stopped before disassembling.

• Always remove the beater,

whisk or dough hook from the bench mixer before cleaning.

• Care should be taken when

removing the food from the mixer bowl by ensuring the motor and the beater, whisk, or dough hook have completely stopped before disassembling. Ensure the speed control dial is in the OFF position, the appliance is switched off at the power outlet and unplugged before

PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST

unlocking the mixer motor head and moving into the upright position. The beater, whisk or dough hook should be released from the mixer motor head before removing the processed food from the mixer bowl and the beater, whisk or dough hook.

• Ensure the mixer motor head

is locked into the horizontal (closed) position when not in use and before storing.

• Always ensure the speed

control dial is in the OFF position, the power is switched off at the power outlet and the power cord is unplugged from the power outlet before attempting to move the bench mixer, before assembling or disassembling, when not in use and before cleaning or storing.

• Do not move the bench mixer

whilst in operation.

• Do not leave the bench mixer

unattended when in use.

• Do not place any part of

the bench mixer in the dishwasher other than the bowl, splash guard, beater, dough hook and whisk.

• Do not place any part of

the bench mixer in the microwave oven.

• Keep the bench mixer

clean. Follow the cleaning instructions provided in this book.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

• Fully unwind the power cord

before use.

• Do not let the power cord

hang over the edge of a bench or table, touch hot surfaces or become knotted.

• To protect against electric

shock do not immerse the power cord, power plug or appliance in water or any other liquid.

• The appliance is not

intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST

• Children should be

supervised to ensure that they do not play with the appliance.

• It is recommended to

regularly inspect the appliance. To avoid a hazard do not use the appliance if power cord, power plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorised Breville Service Centre for examination and/ or repair.

• Any maintenance other than

cleaning should be performed at an authorised Breville Service Centre.

• This appliance is for

household use only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors. Misuse may cause injury.

• This appliance shall not be

used by children.

• The installation of a residual

current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice.

WARNING

Ensure the speed dial control is in the OFF position the bench mixer is switched off at the power outlet and unplugged from the power outlet before attaching the beater, whisk or dough hook.

WARNING

To reduce the risk of injury to persons or damage to the mixer, you must only use the large tools with the large bowl.

• Keep the appliance and its

cord out of reach of children.

SAVE THESE INSTRUCTIONS

PAge heAder.....KNOW YOUR BREVILLE PRODUCT

A. Motor head - Powerful motor for

thorough mixing results.

B. Tilt back and lock down hinge button -

The motor head tilts back and locks into position to allow easy removal of the mixing bowl and attachments.

C. Illuminated LED speed indicator band-

Displays selected mixing task.

D. Pause function - Rotate dial to PAUSE

to temporarily stop mixing and pause the timer.

E. LCD screen with count up & down

timer - Mixer can be set to count down according to a speciﬁed time on a recipe or set to count up to assess mixing time.

F. Internal cord storage - Located in

the rear of the mixer. Cord pushes into the mixer base for convenient and tidy storage.

G. Breville Assist™ handles - Handles on

base and on motor head allow for easy and comfortable lifting of the mixer.

H. Bowl locking recess - The bowl locking

recess allows the bowl to be securely locked into place for safety and stability when the mixer is in operation.

I. Load sensing technology - Mixer

automatically senses the load and adjusts the power to maintain the selected speed (not shown).

J. Splash guard - Prevents ingredients

from splattering out of the bowl.

K. 4.7L stainless steel mixing bowl

with handle.

L. 3.0L stainless steel mixing bowl

with handles.

PAge heAder.....

KNOW YOUR BREVILLE PRODUCT

LARGE BOWL

MIXING AND WHISKING TOOLS

A. Flat beater - Thoroughly mixes a

variety of mixtures such as cake and biscuit batter, pastries, and mashed potatoes.

B. Wire whisk - Consistently mixes

and aerates for egg whites, cream and thin batters.

C. Dough hook - Effectively kneads

heavy dough for bread and pizza.

D. Scraper beater - Scrapes the

sides and bottom of the bowl for exceptionally thorough mixing, of cake and biscuit batter, pastry and frosting.

E. Spatula (not shown).

ABOUT YOUR SCRAPER BEATER

The Breville scraper beater folds ingredients and continuously scrapes down the sides and bottom of the bowl for exceptionally thorough mixing. It virtually eliminates the need to scrape the bowl by hand with a spatula and cuts mixing time up to 60%.

Under-mixed batters produce poorly baked results, resulting in collapsing, unevenness of crumb, holes, low rising, streaking and course textures. The scraper beater will help to ensure a thoroughly mixed batter for your favourite cakes, biscuits, frosting and more.

KNOW YOUR BREVILLE PRODUCT

PAge heAder.....

SMALL BOWL

MIXING AND WHISKING TOOLS

C D

Turn locking nut to

remove wire whisk.

A. 3.0L stainless steel mixing bowl

with handles.

B. Splash guard - Prevents ingredients

from splattering out of the bowl.

C. Scraper whisk - Mixes and aerates

lighter ingredients.

D. Scraper beater - Mixes and scrapes

heavier ingredients.

ASSEMBLY & OPERATION

of your Breville product

PAge heAder.....ASSEMBLY & OPERATION

ASSEMBLING THE MIXER

Before using your bench mixer for the ﬁrst time, remove any packaging material and promotional labels. Ensure the speed control dial is in the OFF position, the mixer is switched off at the power outlet and the power cord is unplugged.

Remove the mixing bowl, beater, whisk and dough hook and wash in warm soapy water with a soft cloth. Rinse and dry thoroughly.

The bowl and the attachments may be washed in the dishwasher.

When ﬁrst using your bench mixer, you may notice an odour coming from the motor. This is normal and will dissipate with use.

ATTACHING EITHER THE LARGE OR SMALL BOWL

The process is the same to insert either the large or small bowl.

1. To remove or insert the mixing bowl, the

mixer motor head must be raised and locked into the open position.

2. Place the mixer on a level, dry bench

top. The mixer motor head should be in the horizontal (closed) position when moving. Raise the mixer motor head by pressing the RELEASE button.

3. Lift the mixer motor head up until it tilts

back and locks into the open position.

4. Insert the mixing bowl into the bowl

locking recess of the mixer stand and turn clockwise until the bowl locks securely into place.

PAge heAder.....ASSEMBLY & OPERATION

ATTACHING THE MIXING AND WHISKING TOOLS

WARNING

To reduce the risk of injury to persons or damage to the mixer, you must only use the large tools with the large bowl.

1. Raise the motor head by pressing the

RELEASE button.

2. Align the groove in the top of the mixing

attachment with the locking pin on the spindle extending down from the mixer motor head.

3. Push the attachment upwards and turn

clockwise until it locks securely onto the locking pin on the spindle (see Fig. 1).

Fig. 1

ASSEMBLING THE SCRAPER WHISK TOOL

The mixing tool for the small bowl converts between a scraper beater and a scraper whisk.

To convert the scraper beater into a scraper whisk, the wire whisk part needsto be locked onto the scraper beater

1. Loosen the locking nut by turning

anti-clockwise.

2. Assemble the wire whisk part onto the

scraper beater.

4. Lower the mixer motor head by pressing

the RELEASE button and gently lowering the mixer motor head until it locks into the closed position.

5. The splash guard can now be assembled

if required. For the large bowl, slide the main ring into position on top of the bowl, then assemble the pour spout. For the small bowl, the splash guard is one piece.

3. With the collar of the whisk in position,

turn the locking nut clockwise to fasten wire in place.

4. Converting the scraper whisk back to

a scraper beater is the same process in reverse. Remember to turn the locking nut anti-clockwise to loosen, and clockwise to tighten.

PAge heAder.....ASSEMBLY & OPERATION

OPERATING THE MIXER

Planetary Mixing Action

By replicating a similar mixing action used by commercial mixers in bakeries and patisseries, the Scraper Mixer Pro head rotates around the bowl while rotating the beater in the opposite direction. This ensures a superior and thorough mixing result without the need for a rotating bowl.

1. Ensure the speed control dial is set to

the OFF position, plug the cord into a 220–240V power outlet and switch the power ON at the power outlet. The illuminated LED speed indicator band will ﬂash and the count up/down timer will display 0:00. The mixer is now ready.

2. Add ingredients to the mixing bowl as

indicated in the recipe.

3. Always begin mixing by selecting a low

speed setting on the speed control dial. Starting on a low speed will prevent ingredients splattering. Increase the speed as suited to the mixing task. The speed setting can be adjusted during operation. If necessary, stop the mixer during operation and scrape any food

mixture down the sides of the mixing bowl with a spatula.

4. If the mixer has not been used for

5 minutes it will automatically change from STANDBY mode to a power saving OFF mode and the illuminated LED will switch off. To exit OFF mode and begin mixing, turn the dial to the selected speed or press one of the count up/down timer buttons.

5. Do not turn the mixer on with the

scraper beater in place if the mixing bowl is empty. This will cause the scraper beater to make a loud noise as it scrapes the bowl.

6. When ingredients are in the mixing

bowl, the scraper beater may make a slight noise as it scrapes the sides and bottom of the bowl. This is normal and should not cause concern.

PAge heAder.....ASSEMBLY & OPERATION

THE COUNT-UP TIMER

The count-up timer is for gauging mixing time. You can monitor the time it takes to thoroughly mix the ingredients, so that the next time you mix the same ingredients you can set the count-down timer for the speciﬁc time.

The count-up timer will automatically begin counting up as soon as the dial is rotated from OFF to one of the speeds. When the dial is turned to PAUSE the total time will be displayed on the LCD and will ﬂash. When the dial is turned to OFF, the LCD display will reset back to 0:00.

THE COUNT-DOWN TIMER

The count-down timer is for any recipe that speciﬁes the length of time ingredients should be mixed. For example, if a recipe reads, “beat for 3 minutes”.

To set the count-down timer, press the up or down arrows until the desired mixing time is displayed on the LCD screen. Press and hold to scroll more quickly.

Rotate the dial to select the desired speed, and begin mixing. When the timer has ﬁnished counting down, it will beep. The motor will automatically turn off and the timer will ﬂash OFF.

The control dial must to be rotated to the OFF position to reset the timer and to continue mixing.

PAUSE MODE

While mixing, at any stage, you can rotate the control dial to the PAUSE setting. This will suspend the timer, and turn the motor off. This enables you to assess the mixing progress or add additional ingredients without affecting the timer.

For example, if you are mixing using the count-up timer mode, you can rotate the control dial from one of the mixing speeds to PAUSE. The mixer motor will stop and the timer will pause.

Once ready, rotate the dial back to one of the mixing speeds and the timer will continue to count-up from the exact time it was paused.

Alternatively, if the mixer is on PAUSE, you can reset the timer to 0:00 by rotating the dial to OFF.

The PAUSE function can also be used in the count-down timer mode. To continue mixing, rotate the dial back into one of the mixing speeds to allow the timer to continue counting down.

PAge heAder.....ASSEMBLY & OPERATION

MOTOR HEAD SAFETY CUT-OFF

The mixer is equipped with a motor head safety cut-off. If the mixer head is lifted up at any time while the mixer motor is switched on, the safety cut-off will automatically switch the motor off and set the mixer into standby mode.

To restart the motor within 5 minutes, lower the mixer head into the hotizontal (closed) position, and turn the dial away then back to the required speed setting. This will resume mixing and the timer will resume counting.

To restart the motor after 5 minutes or more, lower the mixer head and turn the dial to OFF then back to the required speed. The timer will start from 0.

To turn the mixer off (instead of restarting), turn the dial to OFF, and unplug from

the wall.

ELECTRONIC PROTECTION CUT-OFF - CURRENT OVERLOAD

The mixer is equipped with an electric protection cut-off and will automatically stop operating if the motor is stalled or overloaded. This is normally a result of excessive ingredients being processed at one time. Should the mixer go into this mode, the LED indicator band will ﬂash and the error message “E1” will ﬂash on the LCD screen and the buzzer will beep 3 times.

If this error occurs, turn the speed control dial to the OFF position, switch the appliance off at the power outlet and unplug the cord. Remove some of the ingredients in the mixing bowl and then restart the mixer.

THERMO CUT-OFF - TEMPERATURE OVERLOAD

The mixer is equipped with a self-resetting safety device which safeguards against overheating the motor with excessive loads. If overheating occurs, the mixer will automatically activate the overheating protection device and the motor will switch itself off. Should the mixer go into this mode, the LED indicator band will ﬂash and the error message “E2” will ﬂash on the LCD screen and the buzzer will beep 3 times.

If this error occurs, turn the speed control dial to the OFF position, switch the appliance off at the power outlet and unplug the cord. Wait at least 15 minutes before restarting the mixer.

+ 36 hidden pages