Breville BEM820SHB, BEM820BKS User Manual
the Scraper Mixer Twin™
Instruction Booklet
Suits model BEM820
(Combination BEM800 mixer with small bowl)
CONGRATULATIONS
on the purchase of your new Breville product
PAge heAder.....CONTENTS
4 Breville recommends safety first
8 Know your Breville product
11 Assembly & operation
18 Care, cleaning and storage
20 Measuring and weighing
23 Hints and tips
29 Troubleshooting
31 Recipes
3
PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST
We design and manufacture our products with your safety
foremost in mind. We ask that you exercise a degree of care
when using any electrical appliance and adhere to the
following precautions.
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Carefully read all
instructions before operating
the bench mixer for the first
time and save for future
reference.
• Remove and safely discard
any packaging material and
promotional labels before
using the bench mixer for
the first time.
• To eliminate a choking
hazard for young children,
remove and safely discard the
protective cover fitted to the
power plug of this appliance.
• Do not place the bench mixer
near the edge of a bench
or table during operation.
Ensure the surface is level,
clean and free of water and
other substances. Vibration
during operation may cause
the appliance to move.
• Do not use the bench mixer
on a sink drain board.
• Do not place the bench
mixer on or near a hot gas or
electric burner, or where it
could touch a heated oven.
• Always ensure the bench
mixer is completely
assembled before operating.
Follow the instructions
provided in this book.
• Ensure the speed control
dial is in the OFF position
and the bench mixer is
switched off at the power
outlet and the power cord
is unplugged before
attaching the beater, whisk
or dough hook.
• Do not use attachments other
than those provided with the
bench mixer. Use only the
beater whisk and dough hook
supplied with the mixer.
4
PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST
• The maximum dough this
machine can mix is 600
grams flour plus 375ml water.
If your recipe is more than
this, machine must be rested
after 3 minutes of use to
avoid overloading the motor.
• Do not operate the appliance
continuously on heavy loads
for more than 3 minutes.
None of the recipes in
this book are considered a
heavy load.
• Maximum load for the small
bowl is 125g butter, softened
and chopped, with 3/4 cup
caster sugar. Always make
sure your butter is softened
before creaming. Do not use
cold butter.
• Handle the bench mixer and
attachments with care. Never
place your fingers inside
the mixing bowl or near the
beater, whisk or dough hook
during operation.
• Keep hands, hair, clothing,
as well as, spatulas and other
utensils away from moving
beater, whisk or dough hook/
during operation.
• Should an object such as a
spoon or spatula fall into
the bowl while mixing,
immediately ensure the
speed control dial is in the
OFF position, turn the bench
mixer off, unplug at the power
outlet and remove the object.
• Do not place hands in the
mixing bowl unless the bench
mixer is disconnected from
the power outlet. Ensure the
speed control dial is in the
OFF position, the bench
mixer is switched off and
unplugged from the power
outlet before removing the
beater, whisk or dough hook.
• Ensure the motor and beater,
whisk or dough hook have
completely stopped before
disassembling.
• Always remove the beater,
whisk or dough hook
from the bench mixer
before cleaning.
• Care should be taken when
removing the food from
the mixer bowl by ensuring
the motor and the beater,
whisk, or dough hook have
completely stopped before
disassembling. Ensure the
speed control dial is in the
OFF position, the appliance
is switched off at the power
outlet and unplugged before
5
PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST
unlocking the mixer motor
head and moving into the
upright position. The beater,
whisk or dough hook should
be released from the mixer
motor head before removing
the processed food from the
mixer bowl and the beater,
whisk or dough hook.
• Ensure the mixer motor head
is locked into the horizontal
(closed) position when not in
use and before storing.
• Always ensure the speed
control dial is in the OFF
position, the power is
switched off at the power
outlet and the power cord is
unplugged from the power
outlet before attempting to
move the bench mixer, before
assembling or disassembling,
when not in use and before
cleaning or storing.
• Do not move the bench mixer
whilst in operation.
• Do not leave the bench mixer
unattended when in use.
• Do not place any part of
the bench mixer in the
dishwasher other than the
bowl, splash guard, beater,
dough hook and whisk.
• Do not place any part of
the bench mixer in the
microwave oven.
• Keep the bench mixer
clean. Follow the cleaning
instructions provided in
this book.
IMPORTANT SAFEGUARDS
FOR ALL ELECTRICAL
APPLIANCES
• Fully unwind the power cord
before use.
• Do not let the power cord
hang over the edge of a
bench or table, touch hot
surfaces or become knotted.
• To protect against electric
shock do not immerse the
power cord, power plug or
appliance in water or any
other liquid.
• The appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
6
PAge heAder.....BREVILLE RECOMMENDS SAFETY FIRST
• Children should be
supervised to ensure
that they do not play with
the appliance.
• It is recommended to
regularly inspect the
appliance. To avoid a hazard
do not use the appliance if
power cord, power plug or
appliance becomes damaged
in any way. Return the entire
appliance to the nearest
authorised Breville Service
Centre for examination and/
or repair.
• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre.
• This appliance is for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors. Misuse
may cause injury.
• This appliance shall not be
used by children.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current not
exceeding 30mA be installed
in the electrical circuit
supplying the appliance.
See your electrician for
professional advice.
WARNING
Ensure the speed dial control
is in the OFF position the
bench mixer is switched
off at the power outlet and
unplugged from the power
outlet before attaching the
beater, whisk or dough hook.
WARNING
To reduce the risk of injury
to persons or damage to the
mixer, you must only use the
large tools with the large
bowl.
• Keep the appliance and its
cord out of reach of children.
SAVE THESE
INSTRUCTIONS
7
PAge heAder.....KNOW YOUR BREVILLE PRODUCT
A
B
C
D
E
F
G
H
G
I
J
K
L
A. Motor head - Powerful motor for
thorough mixing results.
B. Tilt back and lock down hinge button -
The motor head tilts back and locks into
position to allow easy removal of the
mixing bowl and attachments.
C. Illuminated LED speed indicator band-
Displays selected mixing task.
D. Pause function - Rotate dial to PAUSE
to temporarily stop mixing and pause
the timer.
E. LCD screen with count up & down
timer - Mixer can be set to count down
according to a specified time on a recipe
or set to count up to assess mixing time.
F. Internal cord storage - Located in
the rear of the mixer. Cord pushes into
the mixer base for convenient and
tidy storage.
8
G. Breville Assist™ handles - Handles on
base and on motor head allow for easy
and comfortable lifting of the mixer.
H. Bowl locking recess - The bowl locking
recess allows the bowl to be securely
locked into place for safety and stability
when the mixer is in operation.
I. Load sensing technology - Mixer
automatically senses the load and
adjusts the power to maintain the
selected speed (not shown).
J. Splash guard - Prevents ingredients
from splattering out of the bowl.
K. 4.7L stainless steel mixing bowl
with handle.
L. 3.0L stainless steel mixing bowl
with handles.
PAge heAder.....
KNOW YOUR BREVILLE PRODUCT
LARGE BOWL
MIXING AND WHISKING TOOLS
A
C
A. Flat beater - Thoroughly mixes a
variety of mixtures such as cake and
biscuit batter, pastries, and
mashed potatoes.
B. Wire whisk - Consistently mixes
and aerates for egg whites, cream
and thin batters.
C. Dough hook - Effectively kneads
heavy dough for bread and pizza.
D. Scraper beater - Scrapes the
sides and bottom of the bowl for
exceptionally thorough mixing, of
cake and biscuit batter, pastry
and frosting.
E. Spatula (not shown).
B
D
ABOUT YOUR SCRAPER BEATER
The Breville scraper beater folds ingredients
and continuously scrapes down the sides and
bottom of the bowl for exceptionally thorough
mixing. It virtually eliminates the need to
scrape the bowl by hand with a spatula and
cuts mixing time up to 60%.
Under-mixed batters produce poorly baked
results, resulting in collapsing, unevenness of
crumb, holes, low rising, streaking and course
textures. The scraper beater will help to ensure
a thoroughly mixed batter for your favourite
cakes, biscuits, frosting and more.
9
KNOW YOUR BREVILLE PRODUCT
PAge heAder.....
SMALL BOWL
MIXING AND WHISKING TOOLS
B
A
C D
Turn locking nut to
remove wire whisk.
A. 3.0L stainless steel mixing bowl
with handles.
B. Splash guard - Prevents ingredients
from splattering out of the bowl.
C. Scraper whisk - Mixes and aerates
lighter ingredients.
D. Scraper beater - Mixes and scrapes
heavier ingredients.
10
ASSEMBLY & OPERATION
of your Breville product
PAge heAder.....ASSEMBLY & OPERATION
ASSEMBLING THE MIXER
Before using your bench mixer for the
first time, remove any packaging material
and promotional labels. Ensure the speed
control dial is in the OFF position, the mixer
is switched off at the power outlet and the
power cord is unplugged.
Remove the mixing bowl, beater, whisk and
dough hook and wash in warm soapy water
with a soft cloth. Rinse and dry thoroughly.
The bowl and the attachments may be
washed in the dishwasher.
When first using your bench mixer, you may
notice an odour coming from the motor.
This is normal and will dissipate with use.
ATTACHING EITHER THE LARGE OR
SMALL BOWL
The process is the same to insert either the
large or small bowl.
1. To remove or insert the mixing bowl, the
mixer motor head must be raised and
locked into the open position.
2. Place the mixer on a level, dry bench
top. The mixer motor head should be in
the horizontal (closed) position when
moving. Raise the mixer motor head by
pressing the RELEASE button.
3. Lift the mixer motor head up until it tilts
back and locks into the open position.
4. Insert the mixing bowl into the bowl
locking recess of the mixer stand and
turn clockwise until the bowl locks
securely into place.
12
PAge heAder.....ASSEMBLY & OPERATION
ATTACHING THE MIXING AND
WHISKING TOOLS
WARNING
To reduce the risk of injury to persons
or damage to the mixer, you must only
use the large tools with the large bowl.
1. Raise the motor head by pressing the
RELEASE button.
2. Align the groove in the top of the mixing
attachment with the locking pin on the
spindle extending down from the mixer
motor head.
3. Push the attachment upwards and turn
clockwise until it locks securely onto the
locking pin on the spindle (see Fig. 1).
Fig. 1
ASSEMBLING THE SCRAPER WHISK
TOOL
The mixing tool for the small bowl converts
between a scraper beater and a scraper
whisk.
To convert the scraper beater into a scraper
whisk, the wire whisk part needsto be locked
onto the scraper beater
1. Loosen the locking nut by turning
anti-clockwise.
2. Assemble the wire whisk part onto the
scraper beater.
4. Lower the mixer motor head by pressing
the RELEASE button and gently
lowering the mixer motor head until it
locks into the closed position.
5. The splash guard can now be assembled
if required. For the large bowl, slide the
main ring into position on top of the
bowl, then assemble the pour spout. For
the small bowl, the splash guard is
one piece.
3. With the collar of the whisk in position,
turn the locking nut clockwise to fasten
wire in place.
4. Converting the scraper whisk back to
a scraper beater is the same process in
reverse. Remember to turn the locking
nut anti-clockwise to loosen, and
clockwise to tighten.
13
PAge heAder.....ASSEMBLY & OPERATION
OPERATING THE MIXER
Planetary Mixing Action
By replicating a similar mixing action used
by commercial mixers in bakeries and
patisseries, the Scraper Mixer Pro head
rotates around the bowl while rotating
the beater in the opposite direction. This
ensures a superior and thorough mixing
result without the need for a rotating bowl.
1. Ensure the speed control dial is set to
the OFF position, plug the cord into
a 220–240V power outlet and switch
the power ON at the power outlet. The
illuminated LED speed indicator band
will flash and the count up/down timer
will display 0:00. The mixer is
now ready.
2. Add ingredients to the mixing bowl as
indicated in the recipe.
3. Always begin mixing by selecting a low
speed setting on the speed control dial.
Starting on a low speed will prevent
ingredients splattering. Increase the
speed as suited to the mixing task. The
speed setting can be adjusted during
operation. If necessary, stop the mixer
during operation and scrape any food
mixture down the sides of the mixing
bowl with a spatula.
4. If the mixer has not been used for
5 minutes it will automatically change
from STANDBY mode to a power saving
OFF mode and the illuminated LED will
switch off. To exit OFF mode and begin
mixing, turn the dial to the selected
speed or press one of the count up/down
timer buttons.
5. Do not turn the mixer on with the
scraper beater in place if the mixing
bowl is empty. This will cause the
scraper beater to make a loud noise as it
scrapes the bowl.
6. When ingredients are in the mixing
bowl, the scraper beater may make a
slight noise as it scrapes the sides and
bottom of the bowl. This is normal and
should not cause concern.
14
PAge heAder.....ASSEMBLY & OPERATION
THE COUNT-UP TIMER
The count-up timer is for gauging mixing
time. You can monitor the time it takes to
thoroughly mix the ingredients, so that the
next time you mix the same ingredients you
can set the count-down timer for the
specific time.
The count-up timer will automatically
begin counting up as soon as the dial is
rotated from OFF to one of the speeds.
When the dial is turned to PAUSE the total
time will be displayed on the LCD and will
flash. When the dial is turned to OFF, the
LCD display will reset back to 0:00.
THE COUNT-DOWN TIMER
The count-down timer is for any recipe that
specifies the length of time ingredients
should be mixed. For example, if a recipe
reads, “beat for 3 minutes”.
To set the count-down timer, press the up or
down arrows until the desired mixing time is
displayed on the LCD screen. Press and hold
to scroll more quickly.
Rotate the dial to select the desired speed,
and begin mixing. When the timer has
finished counting down, it will beep. The
motor will automatically turn off and the
timer will flash OFF.
The control dial must to be rotated to the
OFF position to reset the timer and to
continue mixing.
PAUSE MODE
While mixing, at any stage, you can rotate
the control dial to the PAUSE setting. This
will suspend the timer, and turn the motor
off. This enables you to assess the mixing
progress or add additional ingredients
without affecting the timer.
For example, if you are mixing using the
count-up timer mode, you can rotate the
control dial from one of the mixing speeds
to PAUSE. The mixer motor will stop and
the timer will pause.
Once ready, rotate the dial back to one of the
mixing speeds and the timer will continue to
count-up from the exact time it was paused.
Alternatively, if the mixer is on PAUSE, you
can reset the timer to 0:00 by rotating the
dial to OFF.
The PAUSE function can also be used in
the count-down timer mode. To continue
mixing, rotate the dial back into one of the
mixing speeds to allow the timer to continue
counting down.
15
PAge heAder.....ASSEMBLY & OPERATION
MOTOR HEAD SAFETY CUT-OFF
The mixer is equipped with a motor head
safety cut-off. If the mixer head is lifted up at
any time while the mixer motor is switched
on, the safety cut-off will automatically
switch the motor off and set the mixer into
standby mode.
To restart the motor within 5 minutes, lower
the mixer head into the hotizontal (closed)
position, and turn the dial away then back to
the required speed setting. This will resume
mixing and the timer will resume counting.
To restart the motor after 5 minutes or more,
lower the mixer head and turn the dial to
OFF then back to the required speed. The
timer will start from 0.
To turn the mixer off (instead of restarting),
turn the dial to OFF, and unplug from
the wall.
ELECTRONIC PROTECTION
CUT-OFF - CURRENT OVERLOAD
The mixer is equipped with an electric
protection cut-off and will automatically
stop operating if the motor is stalled or
overloaded. This is normally a result of
excessive ingredients being processed at
one time. Should the mixer go into this
mode, the LED indicator band will flash and
the error message “E1” will flash on the LCD
screen and the buzzer will beep 3 times.
If this error occurs, turn the speed control
dial to the OFF position, switch the
appliance off at the power outlet and unplug
the cord. Remove some of the ingredients in
the mixing bowl and then restart the mixer.
THERMO CUT-OFF -
TEMPERATURE OVERLOAD
The mixer is equipped with a self-resetting
safety device which safeguards against
overheating the motor with excessive
loads. If overheating occurs, the mixer will
automatically activate the overheating
protection device and the motor will switch
itself off. Should the mixer go into this
mode, the LED indicator band will flash and
the error message “E2” will flash on the LCD
screen and the buzzer will beep 3 times.
If this error occurs, turn the speed control
dial to the OFF position, switch the
appliance off at the power outlet and unplug
the cord. Wait at least 15 minutes before
restarting the mixer.
16
Loading...