Page
Breville recommends safety first4
Know your Breville Cordless Hand Blender6
Operating your Breville Cordless Hand Blender7
Cordless Hand Blender (stick blender) 10
Congratulations
Cordless Hand Blender (smoothie attachment)12
Cordless Hand Blender (chopper bowl attachment)13
Care, cleaning and storage14
Warranty15
Recipes16
2
on the purchase of your new Breville Cordless Hand Blender
Breville recommends safety first
We at Breville are very safety conscious.We design and manufacture consumer products with the safety of you,
our valued customer,foremost in mind. In addition, we ask that you exercise a degree of care when using any
electrical appliance and adhere to the following precautions:
IMPORTANT SAFEGUARDS FOR BREVILLE
CORDLESS HAND BLENDER
• Read all instructions before operating and save for
future reference.
• Remove any packaging material and promotional
labels before using the Cordless Hand Blender for
the first time.
• Do not place the Cordless Hand Blender (including
the charging base) near the edge of a bench or
table during operation or charging. Ensure the
surface is level, clean and free of water,flour,etc.
• The Cordless Hand Blender (including the charging
base) should be placed on a bench or wallmounted away from sinks or hot surfaces.
• Do not place the Cordless Hand Blender (including
the charging base) on or near a hot gas or electric
burner,or where it could touch a heated oven.
• Always make sure the Cordless Hand
Blender is completely and properly
assembled before operating.
• Always ensure the blending shaft and smoothie
attachment are securely fitted onto the motor
body before operating.
• Do not attempt to operate the Cordless Hand
Blender by any method other than those described
in this booklet.
• Do not unplug the charger plug from the power
outlet by pulling on the cord. Never carr y the
charger plug or charging base by the cord. Grasp
and pull the charger plug to disconnect from the
power outlet. Do not drag or pull cord around sharp
edges or corners.
• If using the Cordless Hand Blender as a stick
blender to blend hot food in a saucepan, remove
the saucepan from the heat source and ensure the
liquid is not boiling.Allow hot food to cool slightly
before blending.The Cordless Hand Blender should
be kept away from any heat source.
• Handle the Cordless Hand Blender and attachments
with care – remember the blades on the blending
shaft are very sharp and should be kept out of
reach of children.
• Do not use attachments other than those provided
with the Cordless Hand Blender.
• Do not operate the appliance continuously for
more than 60 seconds.Allow the motor to rest
for 1 minute between each use.
• Never mix dry,thick or heavy mixtures for more
than 15 seconds. Stop the opera tion and stir the
ingredients before continuing.Allow the motor to
rest for 1 minute between each use.
• Do not leave the Cordless Hand Blender unattended
when in use.
• Always ensure the Cordless Hand Blender charging
base is turned off at the power outlet before
attempting to move, clean or store it.
• Always ensure the Cordless Hand Blender is not
switched on before attempting to attach any of the
accessories.The Cordless Hand Blender safety
system ensures the appliance will not operate
unless the Power button and Speed button
are pressed simultaneously.
• If food becomes lodged around the processing
blade or in the blade guard, s witch off the Cordless
Hand Blender and remove the blending shaft from
the motor body.Use a spatula to dislodge the food.
Do not use fingers as the blades are sharp.The
Cordless Hand Blender safety system ensures the
appliance will not operate unless the Power button
and Speed button are pressed simultaneously.
• Do not remove the Cordless Hand Blender from
ingredients during operation. Ensure the appliance
is switched off and the motor has completely
stopped before removing - to avoid contact with
moving blade, smoothie a ttachment or splashing of
hot liquids.
• To protect against electric shock do not immerse
the motor body,charger plug, power cord or
charging base in water or any other liquid.
• Use only the charger plug and charging base
supplied with this appliance to recharge the
Cordless Hand Blender.
• Do not attempt to use the charger plug and
charging base with any other product
• Never handle the charger plug, charging base
or Cordless Hand Blender with wet hands.
• Keep the appliance clean. Follow the cleaning
instructions provided in this book.
Important safeguards for all electrical appliances
• Do not allow the charging base cord to hang over
the edge of the table or counter,touch hot surfaces
or become knotted.
• This appliance is not intended for use by young
children or infirm persons unless they are
adequately supervised by a responsible person to
ensure that they can use the appliance safely.
• Young children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect the
appliance. Do not use the appliance if charger,
power supply cord, charging base or appliance
becomes damaged in any way.Return the entire
appliance to the nearest authorised Breville Service
Center for examination and/or repair.
• Any maintenance, other than cleaning,should be
performed at an authorised Breville Service Center.
• This appliance is for household use only.Do not
use this appliance for anything other than its
intended use. Do not use in moving vehicles or
boats. Do not use outdoors.
SAVE THESE INSTRUCTIONS
4
5
Know your Breville Cordless Hand Blender
Operating your Breville Cordless Hand Blender
Portable cordless operation
Safety system
ensures the Cordless Hand Blender will not operate unless the Power
button and Speed button are pressed simultaneously
Long lasting 12V battery
2 speed push button control
light press for low speed, firm press for high speed
34 floz (1 liter) capacity mixing jug with storage lid
ideal for blending, measuring and storing a variety
of foods.The jug lid also doubles as a non-slip
base, as it fits both the top and bottom of the jug.
Patented smoothie attachment
for whipping and aerating
Detachable shaft for easy cleaning
Stainless steel ice-crushing blades
Charge light
indicates when the Cordless
Hand Blender is charging
(red) or fully charged
(green)
Before first use
Remove any packaging material and promotional
labels. Remove the blending shaft from the blister
pack and wash the blending shaft in warm soapy
water.Rinse and dry thoroughly.Ensure no water
remains inside the blending shaft to avoid water
ingressing into the motor body when re-attached.
Disassemble mixing jug, stora ge lid and smoothie
attachment and wash in warm soapy water,rinse and
dry thoroughly.Ensure no water remains inside the
smoothie attachment to avoid water ingressing into
the motor body when re-attached.
Dishwashing is not recommended for any part of the
Breville Cordless Hand Blender.
Unlike stick blenders which are plugged into the
power outlet for operation, the Cordless Hand Blender
is safe for use in and around the sink and stove.
However,care should be taken not to immerse the
motor body in water or any other liquid. If using the
Cordless Hand Blender as a stick blender to blend hot
food in a saucepan, remove the saucepan from the
heat source and ensure the liquid is not boiling.
Allow hot food to cool slightly before blending.The
Cordless Hand Blender should be kept away from
any heat source.
The charging base is running at a safe, low
voltage, but it will be damaged if immersed in
water.The charging base should always be
positioned in a clean,dry place well away from
water or other liquids.
Charging the battery before first use:
The battery in the motor body of the Cordless Hand
Blender is shipped either completely discharged of
power or with a small amount of charge.The battery
will require approximately 5 hours to fully recharge
from completely flat.The battery will require a t least
2 hours recharging before it can be used effectively.
Subsequent recharging should take a shorter period
of time depending on the length of time the charging
base has been switched off.
The Cordless Hand Blender motor body has been
designed to be placed on the charging base and left
on charge at all times when not in use.The Cordless
Hand Blender motor body is fitted with a special
protective electronic circuit to prevent overcharging.
Unlike other rechargeable battery technologies, your
high quality Nickel Metal Hydride (Ni-MH) cells have a
high capacity and long life.They do not need to be
completely discharged before recharging.
All rechargeable batteries lose storage capacity
over time. If the Cordless Hand Blender ba ttery
appears to deteriorate so that the operation time is
diminished, return the unit to a Breville Ser vice
Center for battery replacement.
360° charging base
with cord storage
Optional wall
mount included
Chopping bowl
for use as a mini chopper or food processor.
Item not shown.
6
THE CORDLESS HAND BLENDER IS A VERSATILE APPLIANCE
THE CORDLESS HAND BLENDER MOTOR BODY CAN BE ATTACHED TO:
• THE STAINLESS STEEL BLENDING SHAFT – FOR USE AS A STICK BLENDER
• THE SMOOTHIE ATTACHMENT – FOR USE AS A STICK MIXER
• THECHOPPER BOWL WITH CHOPPING BLADE AND LID - FOR USE AS A MINI CHOPPER
OR FOOD PROCESSOR.
7
Operating your Breville Cordless Hand Blender
continued
Overload and low voltage protection
The Cordless Hand Blender is fitted with an
automatic cut-out that will operate if the appliance is
overloaded.This is to protect the motor and battery
from excessive heat build up.The cut-out is only
momentary,and the appliance can then be
re-started. If this automa tic cut-out occurs, reduce
the volume of food being mixed and process in
smaller amounts.
The Cordless Hand Blender is fitted with a second
automatic cut-out that operates when the battery
starts to become flat.This protection is necessary
because applying high loads to flat rechargeable cells
reduces their life. If your a ppliance cuts out without
being overloaded, return it to the charging base until
sufficiently recharged.
Operating time
The actual operating time of the appliance will
vary significantly with the types and quantities of
food being processed, but is typically over 10
minutes with a new,fully charged battery under
average conditions.
Fig 1
Charging base
The charging base recharges the Cordless Hand
Blender and stores the smoothie attachment and
excess cord from the charging base (see Fig.1). The
charging base can be mounted on the wall (see Fig.
2) or placed on a horizontal surface such as a
counter or shelf.
Fig 2
The Cordless Hand Blender is equipped with a
compact charger plug. It takes up a minimum of
space around the power cord.When plugged in, the
charger plug will always remain warm, even after the
charge light changes from red to green.
The charging base stores the excess cord from the
charging base. Simply pull the excessive cord until
the desired length is achieved.The excess cord
can be wrapped inside the cavity under the
charging base.
If you choose to wall mount the charging base,
please follow these steps:
1. Select a convenient position within 3ft (1m) of
an electrical outlet. If the charging base is to be
mounted closer to an outlet,wrap any excess
cord in the cavity under the charging base.
2. Place the wall mount against the wall in the
desired position to mark the drill holes for the
screws (see Fig.3).
Fig 3
The Cordless Hand Blender features a unique safety
switch to ensure the appliance does not operate
accidentally.To activate the Cordless Hand Blender,
follow the sequence below:
1. Depress the Power button for 1 second
Fig 4
2. Continue holding the Power button ,then
depress the Speed button .
Fig 5
Battery charging procedures
1. Plug the charger plug attached to the charging
base into a 110/120 volt power outlet.
2. Place the Cordless Hand Blender motor body into
the charging base, making sure tha t it firmly sits
in the charging base and the red charging light
illuminates.Your Cordless Hand Blender will
begin charging.When the battery is fully charged
the charging light will change to green.
3. To maintain the charge in the motor body, keep
the charging base plugged into a standard power
outlet.When charging, the charger plug may be
warm to the touch – this is normal. It is
impossible to overcharge the battery because the
Cordless Hand Blender is designed with
overcharge protection circuitry.
8
X
Mark drill holes here
3. Drill a 0.2inch (5mm) diameter hole through the
center of each drill hole mark. Push a plastic wall
anchor into each drilled hole.
4. Insert a screw into each drilled hole and turn
until the screw heads are 0.1inch (3mm) above
the wall surface.
5. Slide the wall mount onto the screws and attach
the charging base to the wall mount.
X
3. To select the desired speed:
I. For low speed, lightly depress the Speed button
II. For high speed,firmly depress the Speed button
Ensure the Power button is depressed first.
Ensure the Power button has been depressed
for 1 second before depressing the Speed button.
Ensure both the Power button and Speed
button are depressed together.
Note
9
Cordless Hand Blender (stick blender)
To detach the stainless steel
blending shaft
Ensure the Cordless Hand Blender is switched off by
keeping hands clear of the Power button and Speed
button. Unscrew the blending shaft from the
motor body in a clockwise direction (See Fig.1).
Fig 1
To attach the stainless steel
blending shaft
Hold the shaft with the blades down, and align the
top end of the blending shaft with the corresponding
end of the motor body.Screw the shaft into the motor
body in an anti-clockwise direction.
To use the stick blender
Ensure the stick blender is completely and properly
assembled as detailed on the left.
1. Place food to be processed into the mixing jug
provided (or a sufficiently large mixing bowl or
saucepan).The mixing jug provided should only
be filled up to the 'LIQUID MAX' mark when
blending liquids.
2. Place the blending shaft as deeply as possible
into the mixing jug and depress the Power button
(top button) to turn the Cordless Hand Blender
on.While still depressing the Power button,
depress the Speed button (bottom button).To
select the desired speed, the Speed button
should be lightly depressed for low speed and
firmly depressed for high speed. Both the Power
button and the Speed button must be depressed
simultaneously for the required duration of
operation (see Fig. 2).
Fig 2
Power button
Speed button
3. Work through the ingredients in the mixing jug
with a gentle raising and lowering motion.
4. Switch off the Cordless Hand Blender motor by
releasing the Power and Speed buttons.
5. Ensure the motor has completely stopped before
lifting the Cordless Hand Blender out of the
mixing jug.
Recommendations when using
the Cordless Hand Blender as a
stick blender:
• The Cordless Hand Blender blends foods and
liquids rapidly,therefore it is easy to over-process.
Remember when using the Cordless Hand Blender,
check food throughout operation.
• The stainless steel blending shaft on the Cordless
Hand Blender allows for hot food to be processed
directly in the saucepan.This makes blending
soups and sauces very easy.For safety reasons,
remove the saucepan away from the heat source
before processing. Ensure the Cordless Hand
Blender is kept away from any heat source.
• When pureeing and blending, cut food into
uniform sizes.This will ensure smooth and
consistent results.
• Warm all liquids to be added to soups and purees,
this will ensure even blending.
• Use the storage lid of the mixing jug as a non slip
base for the jug during blending.This will keep the
jug stable.
• Do not operate the appliance continuously for more
than 60 seconds.Allow the motor to rest for 1
minute between each use.
If food becomes lodged around the
blade or in the blade guard, follow
these safety instructions:
1. Switch the Cordless Hand Blender off by
releasing the Power and Speed buttons.
2. Remove the blending shaft from the motor body.
3. Use a spatula to carefully dislodge the food.Do
not use fingers as the blades are sharp.
4. After the food has been removed and the blades
are clear, re-attach the blending shaft to the
motor body and continue blending.
THE STAINLESS STEEL ICE CRUSHING BLADES ON THE BLENDING SHAFT ARE
EXTREMELY SHARP, KEEP FINGERS AWAY FROM THE BLADES AT ALL TIMES.
10
11
Cordless Hand Blender (smoothie attachment)
Cordless Hand Blender (chopper bowl attachment)
To detach the smoothie attachment
Ensure the Cordless Hand Blender is switched off by
keeping hands clear of the Power button and Speed
button. Unscrew the smoothie a ttachment from the
motor body in a clockwise direction (See Fig.1).
Fig 1
To attach the smoothie attachment
Hold the shaft with aerating blades down, and align
the top end of the smoothie attachment with the
corresponding end of the motor body.Screw the shaft
into the motor body in an anti-clockwise direction.
To use the smoothie attachment
Ensure the smoothie attachment is completely and
properly assembled as detailed on the left.
1. Place food to be processed into the mixing jug
provided (or a sufficiently large mixing bowl or
saucepan).The mixing jug provided should only
be filled up to the 'LIQUID MAX' mark when
blending liquids.
2. Place the smoothie attachment as deeply as
possible into the mixing jug and depress the
Power button (top button) to turn the Cordless
Hand Blender on.While still depressing the
Power button, depress the Speed button (bottom
button).To select the desired speed,the Speed
button should be lightly depressed for low speed
and firmly depressed for high speed. Both the
Power button and the Speed button must be
depressed simultaneously for the required
duration of operation (see Fig. 2).
Fig 2
Power button
Speed button
3. Work through the ingredients in the mixing jug
with a gentle raising and lowering motion.
4. Switch off the Cordless Hand Blender by
releasing the Power and Speed buttons.
5. Ensure the motor has completely stopped before
lifting the Cordless Hand Blender out of the
mixing jug.
To detach the chopper attachment
• Remove the motor from the chopper lid.
To attach the chopping blade, chopping
bowl and lid
• Place the food inside the chopper bowl. Do not
exceed the max marking.
• Ensure the chopper bowl lid is dry with no water
left inside before reattaching.
Always place the chopping blade on its pivot
pin on the bottom of the bowl before placing
any contents into the bowl. Do not lift the
blade before the complete chopping operation
is finished.
Note
To use the chopper bowl
Ensure the chopper is completely and properly
assembled as detailed on this page.
1. Depress the Power button (top button) to turn the
Cordless on.While depressing the Power button,
depress the Speed button (bottom button).
To select the desired speed,the Speed
button should be lightly depressed for low
speed and firmly depressed for high speed.
Both the Power button and the Speed button
must be depressed simultaneously for the
required duration of operation.
2. When processing has finished,switch off the
Cordless Hand Blender by releasing the Power
and Speed buttons.
3. Ensure the motor has completely stopped before
removing the motor body from the lid of the
chopper bowl.
Recommendations when using
the Cordless Hand Blender with
Chopper Bowl
• Do not operate your Cordless Hand Blender when
the chopper bowl is empty.
• During processing, hold the motor body with one
hand and chopper bowl and lid with the other.
• When processing, cut food into uniform sizes to
ensure quicker,even and more consistent results.
• DO NOT process hard foods such as coffee, cereals
or chocolate in lumps and this may result in
damage to the blade.
• DO NOT process boiling or hot foods in the
chopper bowl.
• NEVER remove the blade from the bowl before the
processing is completed.
• The Cordless Hand Blender blends food and liquids
rapidly,therefore it is easy to over process.
Remember to check food throughout the operation.
12
13
Care, cleaning and storage
Warranty
Dishwashing is not recommended for
any part of the Cordless Hand Blender.
Under no circumstances should the blending shaft be
placed in the dishwasher.The caustic chemicals used
in dishwashers will inevitably damage the seals and
bearings that support the rotating shafts reducing
their service life.
For longest life,we recommend hand washing the
exposed blade portion of the blending shaft in the
sink, a voiding water entering the inside of the shaft
as much as possible.
While the transparent mixing jug is made from high
quality plastic material, (which will not be damaged
by the occasional dishwashing on the top shelf only),
for maximum life we recommend hand washing in
the sink.
Stick blender
Ensure the Cordless Hand Blender is switched off by
releasing the Power and Speed buttons. Remove the
stainless steel blending shaft from the motor body.
The stainless steel blending shaft should be hand
washed in hot soapy water,rinsed and dried
thoroughly after each use. Do not use abrasive
cleaners or steel wool.
QUICK WASH:Between each processing task, with
the motor body attached and turned off, place the
stainless steel blending shaft into a jug of water then
depress the low speed for 5 seconds.This will
remove any food on the blade and blending shaft and
allow you to continue onto the next processing task.
Blades are extremely sharp, handle with care.
Motor body
Ensure the Cordless Hand Blender is switched off by
releasing the Power and Speed buttons. Remove the
motor body from the stainless steel blending shaft.
To remove any food residue from the motor body,
wipe with a damp cloth only. Do not use abrasive
cleaners or steel wool.Never immerse the motor
body in water or any other liquid.
Smoothie attachment
Ensure the Cordless Hand Blender is switched off by
releasing the Power and Speed buttons. Remove the
smoothie attachment from the motor body.
The smoothie attachment should be hand washed in
hot soapy water,rinsed and dried thoroughly after
each use. Do not use abrasive cleaners or steel wool.
Chopper bowl
Ensure the Cordless Hand Blender is switched off by
releasing the On and Speed buttons. Remove the
motor body from the chopper bowl lid, then remove
the lid and chopper blade from the chopper bowl.
The chopper bowl, chopper bowl lid and chopping
blade should be hand washed in hot soapy water,
rinsed and dried thoroughly after each use. Do not
use abrasive cleaners or steel wool.
Storage
Ensure the Cordless Hand Blender is switched off by
releasing the Power and Speed buttons. Ensure the
appliance is clean and completely dry.
For safety reasons,it is recommended to store the
motor body and smoothie attachment on the charging
base, and keep the blending shaft in a convenient
cupboard or drawer.
One year limited warranty
Breville®* warrants this Breville® appliance against
defects that are due to faulty material or
workmanship for a period of (1) year from the date
cited on the original purchase receipt.This warranty
does not cover damage from abuse, neglect,use for
commercial purposes, or an y other use not found in
the printed “Instructions for use”booklet. Should the
customer choose to tamper with, or intentionally
dismantle the product, the Warranty will automatically
be deemed void.There is no warranty for glass parts,
glass containers, filter basket, blades and agitators.
HWI Breville® expressly disclaim all responsibility for
consequential damages for incidental losses caused
by use of this appliance. Some states or provinces do
not allow this exclusion or limitation for incidental or
consequential losses, so the foregoing disclaimer
may not apply to you.
ANY WARRANTY OF MERCHANTABILITY OR FITNESS
WITH RESPECT TO THIS PRODUCT IS ALSO LIMITED
TO THE ONE YEAR LIMITED WARRANTY PERIOD.
Some states or provinces do not allow disclaimer of
the implied warranty with respect to consumer
goods, so the foregoing disclaimer may not apply
to you.
This warranty gives you specific legal rights and you
may also have other legal rights which vary from
state to state or province to province.
If this appliance should become defective within the
warranty period, do not return the a ppliance to the
store. Please contace our Customer Ser vice Center.
chopper bowl and blend the ingredients
until smooth.
Serve on warm crusty bread.
Basic pesto sauce
1 cup fresh basil leaves
1 tablespoon fresh lemon juice
2 tablespoons extra virgin olive oil
2 cloves garlic
1
⁄4cup roasted peanuts
Freshly ground black pepper
1. Place all ingredients into the chopper bowl.
2. Assemble the Cordless Hand Blender on
the chopper bowl and blend the ingredients
until smooth.
Milkshakes
1 cup chilled milk
2 scoops vanilla ice cream
1
⁄4teaspoon vanilla extract
1. Place all ingredients into mixing jug.
2. Place the Cordless Hand Blender assembled with
the smoothie attachment into the ingredients and
blend until smooth and frothy (about 30 seconds).
Flavor variations
Chocolate
Add 1 tablespoon chocolate syrup
Or
1
⁄2tablespoon cocoa and 1⁄2tablespoon malt.
Strawberry
Add 1 tablespoon strawberry syrup.
Cool banana
Makes 4 small glasses
1 cup chilled milk
1 medium banana, peeled and chopped
2 tablespoons malted milk powder
1 teaspoon chopped fresh mint
2 scoops vanilla ice cream
Mint sprigs, for garnish
1. Place all ingredients except garnish into
mixing jug.
2. Place the Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until thick and smooth (about 30 seconds).
3. Pour into glasses, garnish and serve immediately.
Banana strawberry soy
Makes 4 small glasses
1 cup chilled vanilla soy milk
1
5
⁄2 oz (150g) strawberries, hulled and halved
1 medium banana, peeled, cut into quarters
2 scoops vanilla ice cream
Extra strawberries, for garnish
1. Place all ingredients except garnish into
mixing jug.
2. Place Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until thick and smooth (about 30
seconds).
3. Pour into glasses, garnish and serve immediately.
Big berry
Makes 4 small glasses
1 cup chilled milk
1
⁄2 oz (100g) strawberries, hulled and halved
3
1
3
⁄2 oz (100g) blueberries
3
1
⁄4 oz (50g) raspberries
2 teaspoons chopped fresh mint
2 scoops vanilla ice cream
Extra berries and mint sprigs, for garnish
1. Place all ingredients into mixing jug.
2. Place the Cordless Hand Blender with the
stainless steel blending shaft attached into
the ingredients and blend until thick and
smooth (about 30 seconds).
3. Pour into glasses, garnish and serve immediately.
22
23
Drinks
Cocktails
So good
Makes 4 small glasses
1 cup chilled vanilla soy milk
smoothie attachment into the ingredients and
blend until thick and smooth (about 30 seconds).
3. Pour into glasses and serve immedia tely.
Get up and go breakfast shake
1
⁄2cup chilled milk
1
⁄2cup chilled fruit juice
1 egg
1 tablespoon honey
1. Place all ingredients into mixing jug.
2. Place the Cordless Hand Blender assembled with
the smoothie attachment into the ingredients and
blend until smooth and creamy (about 30 seconds).
3. Pour into glasses and ser ve immediately.
Margarita
2 floz (60 ml) tequila
2 floz (60 ml) cointreau
2
2
⁄3floz (80 ml)lime juice
12 ice cubes
1. Place all ingredients into mixing jug.
2. Place Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until well combined and ice is crushed
(approx 30 seconds).
Serve in salt rimmed glasses.
Daiquiris
Basic Recipe
About 1 cup fruit
4 floz (120ml) white spirits
(white rum, vodka, kirsch)
4 floz (60ml) sugar syrup
1 cup ice
1. Place all ingredients into mixing jug.
2. Place Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until smooth (approx 30 seconds).
3. Pour into glasses and seve immediately.
Most fresh fruit and berries can be used. If using
frozen fruit defrost before use. Fruit with hard
skins or stones must have them removed before
pureeing. Large fruit must be diced first.
Note
24
25
Non-Alcoholic Drinks
Desserts / Baby food
Fruit Cocktail
1 cup pineapple juice
1 banana, peeled and chopped
1 orange, skin and pith remo ved and quartered
1 cup soda water
2 tablespoons passionfruit pulp
1. Place pineapple juice,banana and orange into
mixing jug.
2. Place the Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until smooth (approx 30 seconds).
3. Stir in passionfruit pulp and soda water and serve.
Rockmelon and pineapple frappe
1 cup chopped rockmelon
1 cup canned pineapple pieces
1 cup ice
Mint leaves, to ser ve
1. Place rockmelon,pinea pple and ice into the
mixing jug.
2. Place the Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until ice is crushed and mixture is
smooth and thick.
Serve with chopped mint leaves.
Crepe batter
11⁄2cups plain flour
Pinch salt
2 eggs
1
1
⁄2cups milk
1 tablespoon oil
1. Place all ingredients into mixing jug.
2. Place the Cordless Hand Blender with the stainless
steel blending shaft attached into the ingredients
and blend until just combined (about 40 seconds).
1
3. Pour
⁄4 cup of mixture into a preheated and lightly
greased frypan. Cook until light golden brown,turn
and cook other side. Remove, keep warm. Repeat
with remaining mixture.
4. Serve hot drizzled with lemon juice and sprinkled
with finely granulated sugar.
Vegetable blend
1 cup steamed vegetables
1. Place vegetables into mixing jug.
2. Place the Cordless Hand Blender with stainless
steel blending shaft attached into vegetables and
blend until smooth (about 30 seconds).
Liquids (for example milk, formula or wa ter) may
be added to thin the mixture down depending on
the age of the child.
Note
26
27
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.