Braun BS 5884, BS 5885, BS 5888, BS 5887, BS 5886 User Manual

washable
start• stop
washable
Contour 5888
www.braun.co.jp
23456
6
e
c
a
l
p
e
r
t
e
s
e
r
e
c
a
l
p
e
r
7
5887 5888
6
P O W E R
c
a
l
p
e
r
5886 5885
charge
e
e
r
empty
e
e
c
c
a
a
l
l
p
p
e e
r r
t
e
s
7
5884
1
t
e
s
e
r
2
3
washable
t
t
e
e
s
s
e
e
r
r
Contour 5888
stop
start•
washable
4 5
6 7
8 9
10 11
7
washable
start•stop
le
88
washable
8
9
washabl
e
Contour 5888
10
11
on • off
on • off
start•stop
12
start•stop
13
5000
Series
Contour
100%
100%
14
1516171819
English
Our products are designed to meet the highest standards of quality, functionality and design. We hope you enjoy your new Braun Shaver.
Warning
Your shaver is provided with a special cord set with an integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it. Otherwise there is risk of electric shock.
Description
1 Shaver foil 2 Cutter block 3 Release button 4 Long hair trimmer 5 On/off switch («start/stop») 6 Charging lights 7 Low-charge light (red) 8 Replacement light for shaving parts
9 Reset button 10 Special cord set 11 Charging stand (5888 / 5887 models only)
Charging lights
The 3 charging lights (6) blink to indicate the charging level by thirds. When fully charged, all 3 charging lights shine permanently.
5884 model only features one charging light that blinks when the shaver is being charged.
Low-charge light
The red low-charge light flashes when the battery capacity has dropped below 20%, provided the shaver is switched on. The re­maining capacity will then be sufficient for 2 to 3 shaves.
Shaving
Turn on the shaver ("start"): The pivoting cutting system automatically adjusts to every contour of your face.
Charging
The best environmental temperature for charging is between 15°C and 35°C.
• Using the special cord set, connect the
shaver to an electrical outlet with the motor switched off.
• When charging for the first time, leave the
shaver to charge continuously for 4 hours.
• Once the shaver is completely charged,
discharge the shaver through normal use. Then recharge to full capacity. Subsequent charges will take about 1 hour.
• A full charge provides up to 50 minutes of
cordless shaving time depending on your beard growth.
• Maximum battery capacity will only be
reached after several charging/discharging cycles.
• If the rechargeable batteries are dis-
charged, you may also shave by connecting the shaver to an electrical outlet via the special cord set.
Trimmer:
When the long hair trimmer is activated, it allows the controlled trimming of moustache or sideburns.
Tips for the perfect shave
• We recommend that you shave before washing, as the skin tends to be slightly swollen after washing.
• Hold the shaver at right angles (90°) to the skin. Stretch the skin and shave against the direction of beard growth.
• To maintain 100% shaving performance, replace the shaver foil and cutter block, when the replacement light (8) comes on (after about 18 months), or when the shaving parts are worn.
20
Cleaning
This appliance is suitable for cleaning under an open water tap.
Warning: Detach the hand-held part from the power supply before cleaning it in water.
Regular cleaning ensures better shaving performance. Rinsing the shaving head after each shave under running water is an easy and fast way to keep it clean:
• Switch the shaver on (cordless) and rinse
the shaving head under hot running water. A natural based soap may also be used provided it contains no particles or abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.
• Next, switch off the shaver, remove the
shaver foil and the cutter block. Then leave the disassembled shaving parts to dry.
• If you regularly clean the shaver under
water, then once a week apply a drop of light machine oil onto the long hair trimmer and shaver foil.
Alternatively, you may clean the shaver using the brush provided:
• Switch off the shaver. Remove the shaver
foil.
• Using the brush, clean the cutter block and
the inner area of the shaver head. However, do not clean the shaver foil with the brush as this may damage the foil.
Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil and cutter block: 5000 series)
The replacement light will remind you during the next 7 shaves to replace the shaving parts. Then the shaver will automatically reset the display. After you have replaced the shaving parts (foil and cutter block), use a ball-pen to push the reset button (9) for at least 3 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete. The manual reset can be done at any time.
Preserving the batteries
In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (by shaving) every 6 months approximately. Then recharge the shaver to full capacity. Do not expose the shaver to temperatures higher than 50°C for extended periods of time.
Environmental notice
This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Repair Centre or at appropriate collection points provided in your country.
Keeping your shaver in top shape
About every four weeks, clean the cutter block with Braun cleaning agents.
Replacement light for shaving parts / Reset
To maintain 100% shaving performance, replace your foil and cutter block, when the replacement light for shaving parts (8) comes on (after about 18 months) or when worn.
Subject to change without notice.
This product conforms to the European Directives EMC 89/336/EEC and Low Voltage 73/23/EEC.
For electric specifications, see printing on the special cord set.
21
22
23
5-736-462/01/VI-06
Loading...