Page 1
0415
Page 2
INSTRUCTIONS
CONTENTS
Panel Introduction
Basic Function
Remote Control Operation
Turn on/off
Access main interface
USB/SD Card Operation
Radio Operation
BT Operation
External input operation
Steering wheel setting
AUDIO setting
Other functions
Rear view function
Access setup interface
Audio setting
Date setting
General setting
System setting
Language setting
Touch calibrate
Wiring Diagram
Trouble shooting
Specifications
Accessory
02
03
04
06
06
06
07
08
09
09
09
09
09
10
10
10
10
10
10
10
11
11
12
13
Warning: To ensure safety while driving and to comply with laws, drivers should
not watch video or operate the video device while driving.
01
Page 3
INSTRUCTIONS INSTRUCTIONS
ACCESSORY
Wire
Keys
Remote controller
Warranty card
Accessory
PANEL INTRODUCTION
Quantity
1PC
2PCS
1PC
2PCS
1. PWR/VOL button
2. MUTE button
3. MODE button
4. SD slot
5. USB slot
6. AUX slot
7. RESET
8. IR
0213
Page 4
BASIC FUNCTION
1.
PWR/VOL button
Press this button will turn on power, during working longer press this button will turn off
power, on any mode, shortly press will return main menu, rotate this button will adjust
volume level.
2. MUTE button
Press this button to shut off sound output, repress this button to resume sound output;
Press this button longer to turn on/off TFT LCD display.
3. MODE button
When the unit is power on, Repeat press this button can switch to different function
mode as following picture.
Note: When the device without connection to USB, SD,
the system will automatically skip these related working
mode.
4. SD slot
Insert SD card, the unit will play the files automatically.
5. USB slot
Insert USB removable device so as to read audio/video files.
6. Dual (front and rear) AUX
To input external audio.
Warning: You can only use either front or rear AUX at a time. Never connect both
front and rear AUX at the same time.
BT
SPECIFICATIONS
Power supply
Power range
Max Current Consumption
Ground system
Power Output
FM tuner
US frequency range
European frequency range
Signal / Noise ratio
Stereo separation
Search station volt
AM tuner
US frequency range
European frequency range
Limit noise sensitivity
INSTRUCTIONS
DC 12V
10.8-16.0V DC
15A
Negative ground
80 WattsX4 Channels
87.5-107.9MHz
87.5-108MHz
55dB
30dB
20-30dBuv
530-1710KHz
522-1620KHz
32dB
7. RESET
Press this button and this unit will be restored to the initial state.
8. IR
To receive infrared signal from the remote control.
This unit is with switchable frequency.
You can switch from USA frequency to Europe frequency by following the below steps:
Step1. In main menu, press setup icon to enter the setup interface.
Step2. Press the Radio icon, and insert password 888888, then press “OK”,
the menu from which you can select the radio frequency will show.
Step3. Press “Radio region” and select the desired frequency by pressing the “up”
and “down” arrow, then press it and setting is finished.
1203
Page 5
WIRING DIAGRAM
Remote Control Operation
This player is equipped with ISO standard connector, please follow below instruction:
● Red - ACC ON (+12V)
● Yellow – 12 V Constant
● Black – Ground wire
● Blue - Power Antenna / Remote Amp Turn On
● Purple/White-Reverse Gear Signal (+)
● Grey/Grey black - Right front speaker (+/-)
● White/White black - Left front speaker (+/-)
● Purple/Purple black - Right rear speaker (+/-)
● Green/Green black - Left rear speaker (+/-)
● Light Green-Parking Brake (-)
TROUBLE SHOOTING
PROBLEM
Cannot power on
After ignition switch
off, setting
information all lose
Poor performance
of radio station
Cannot switch
language/subtitle
No image
Cannot watch
image during
driving
Check fuse
Some factors cause MPU
wrong operation
Change battery or fuse
Weak signal
There is only one language/
subtitle
Other factors cause MPU
wrong operation
It’s not allowed to watch image
during driving
CAUSE SOLUTION
Change fuse same as the old one
Press RES button on the panel by
then, power on
Reset information and save
Move the car to another place, then research
If not with multi - language/subtitle, it cannot
switch language/subtitle
Press RES button on the panel by penpoint,
then, power on
Park the car in a safe place, put the car stall
in “ P ” postion, pull up the hand brake,
parking brake wire must be grounded
penpoint,
1. (Power) button
Press the button to turn power on/off.
2. MODE (mode switch) button
When the power is on, each time the
button is pressed, the mode switches
between RADIO/USB/SD (MMC) /AUX.
3. MUTE button
Press the button to turn off volume output,
repress the button to resume previous
volume level.
4. Number button
.Number button 2/RPT (repeat playback)
Under FM/AM radio status, short press the
button to get into the corresponding stored
radio channels. After searching for a
station manually, hold the button for 2
seconds to save the station in the number
button 2's position. Repeat playback.
Under USB playback status, press the
button to repeatedly play the current song,
repress it to cancel repeat playback.
.Number button 3/RDM (random
playback)
Under FM/AM radio status, short press the
button to get into the corresponding stored
radio channels. After searching for a station
manually, hold the button for 2 seconds to
save the station in the number button 3's
position. Random playback.
Under USB playback status, press the
button to play songs in the disc randomly,
repress it to cancel random playback.
.Number button 4
Under FM/AM radio status, touch the button
to get into the corresponding stored radio
channels. After searching for a station
manually, hold the button for 2 seconds to
save the station in the number button 4's
position.
Under USB playback status, press the
button to select the current folder.
.Number button 5 Long press 5/DIR- to
select the previous folder/short press to
play the -10 song
Under FM/AM radio status, touch the button
to get into the corresponding stored radio
channels. After searching for a station
manually, hold the button for 2 seconds to
save the station in the number button 5's
position.
Under USB playback status, touch the
button to select the -10 song cyclically.
Long touch the button to select the previous
folder.
0411
Page 6
INSTRUCTIONS
Access setup interface
.Number button 6 Long press 6/DIR+ to
select the next folder/short press to
play the +10 song
Under FM/AM radio status, touch the button
to get into the corresponding stored radio
channels. After searching for a station
manually, hold the button for 2 seconds to
save the station in the number button 6's
position.
Under USB playback status, touch the
button to select the +10 song cyclically.
Long touch the button to select the next
folder.
5. SEL Button
The function is the same as the function of
SEL button on panel.
6. Button
In radio/AUX mode, press the button to
return to the interface;
In USB/SD mode, press the button:
current interface → repertoire interface →
interface.
7. / / / Button
Press “ ” button to select the folder →
AUDIO → IMAGE, press “ ” button to
select the next folder.
BATTERY CHANGE
When control distance of remote control
becomes shorter or no function, please
change battery. Please confirm polarity
before change.
One hand press stopper, then pull out
battery.
Put battery into controller.
Insert battery holder into controller.
Click [Setup] icon on main interface to access setup interface.
Audio setting
Click [AUDIO] icon on setup interface to access audio
setting interface.
You can turn on or turn off the existing functions on audio
setting interface and adjust the rearview volume.
Date setting
Click [DATE] icon on setup interface to access time setting
interface.
Click [12 Hour] icon on time bar [Time Mode 12 Hour]
time setting interface shall display, Can be set time mode.
Click [AM 12:02] icon on time bar [Set Time AM 12:02]
time setting interface shall display, Can be set time.
Click [2012/01/01] icon on time bar [Set Date 2012/01/01]
time setting interface shall display, Can be set Date.
General setting
Click [GENERAL] icon on setup interface to access general
setting interface.
In general setting interface, you can select to turn on or turn
off the existing functions.
System setting
Click [SYSTEM] icon on setup interface to access system
setting interface.
8. ENTER button
9. VOL+/- button
Press this button to increase/decrease
volume level.
10. Button
Press this button so as to switch between
play and pause.
11. Button
The function is the same as the function
of buttons on panel.
Language setting
During use, you can select your familiar language to display menu by language setup.
Click the corresponding [English] icon on the language bar desired to be set so as to
switch the language type, when there are more than 3 languages, direction icon shall
pop up, click it to select your familiar language.
Touch calibrate
If touch calibration error occurs, you can adjust the touch coordinate by “Touch calibrate”.
Click [Touch Calibrate] icon on system setting interface, to confirm to access touch
calibration interface.
Touching methods
Use touch pen to click the center of “+” icon, and move along with center of “+” icon so
as to calibrate the screen. It shall automatically save data and exit after screen
calibration. Please accurately click all positions on screen, or the accuracy of touch
calibration shall be affected.
1005
Page 7
External input operation
Turn on/off
Connect the video input plug with external video input
jack, and connect the audio input plug with external
audio input jack.
Touch [Aux] icon on main interface to access external
input interface.
Steering wheel setting
1. Click on the [SWC] icon in the main interface into
the steering wheel settings interface.
2. The original vehicle to the control line positive,
negative with the machine control line in the positive
and negative connection.
3. Click the steering wheel buttons will appear
corresponding operating tips, and fundamental operation prompts the steering wheel
feature set.
4. Set function to save the settings and click the Confirm icon to confirm.
Note: To modify function settings, repeat procedures 3~4.
To reset functions, click [Reset] icon, all the settings set before shall be cleared, repeat
procedures 3~4 for resetting.
AUDIO setting
Click on the [AUDIO] icon in the main interface enter
the AUDIO setting interface.
Drag on each volume, treble, bass bar icon
associated settings.
Click icon to adjust the speaker channel.
Click LOUD icon at the option on / off loudness.
Click SUB icon at the option on / off subwoofer.
Click RESET icon restore the initial settings.
When the ignition switch is put in ACC or ON position, Press button on the front
panel to turn on the unit. After the host starts, hold power button for 3 seconds, the host
will turn off.
power
Access main interface
Turned on, the interface to return the icon to switch to the main interface. As shown
below:
Touch the function icons so as to access the corresponding function operations.
USB/SD Card Operation
When there is a USB device/SD card connected, the unit can conduct the playback of
audio/video/image files in the USB device/SD card.
Insert/Eject USB storage device
1. Connect a U disc recorded with media information to the unit by a USB connecting
cable.
2. When there is a need to eject the USB device, exit the USB device playback screen
first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit
correctly until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card
and it shall pop up after unlocking.
Other functions
Rearview function
In any running state, the video signal can switch to reverse video state when reversing
the car, and the system shall return to its initial running state after reversing the car.
Warning
Do not solely rely on rear view camera.
Objects maybe reversed ,always be
aware of you surroundings.
Reverse field simulation
Rearview backup image
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the
unit has connected with a USB device or SD card, touch [USB] icon in the multimedia
interface to enter into the external storage playback interface; Touch [SD] icon to enter
into the SD card playback interface. During playback, touch the top center area of the
screen to pop up the touch menu, operate touch menu to perform various playback
controls.
Play
After SD card/USB removable device being read out, you can by clicking the play files.
Native support for playback the MP5 formats (including: *. rm, *.rmvb, *.wmv, *.wma,
*.wav, *.dat, *.flv, *.asf, *.mov, *.DivX, *.vob, *.avi, *.fsm, *.mp3, *.mp2, *.mp4, *.mpg etc.)
0609
Page 8
Radio Operation
BT Operation
Enter/exit
1.
Touch [Radio] icon in the main interface to enter into the radio interface.
Touch icon to return to main interface, and then touch other function icons so as to
exit radio mode.
2. Mute: Click icon, mute on/off.
3. Band selection
Click icon so as to switch among FM1, FM2, FM3, AM1,
AM2 bands.
4. Search/Save radio stations
Short press icon to browse the stored radio stations.
FM band can save 18 radio stations (Six stations for FM1/
FM2/FM3), AM band can save 12 radio stations (Six stations
for AM1/AM2).
5. Sound setting: Click icon to access sound setting interface.
6. Turn on/off the Long/Short-range
Click icon, the search pattern in the local search (LOC) and remote search (DX)
switch between. LOC feature is turned on after the signal is strong enough only to listen
to those in good condition and receiving radio station; DX enabled, you can receive
remote weak radio signals.
Note: This function is available only when FM band is selected.
7. Loudness on/off
Click icon so as to turn on/off loudness function.
8. Stereo on/off
When receiving stereo signals, click icon to turn on/off stereo.
9. TA (Receive traffic information)
ON: When the traffic station is turned on, the radio will automatically search for traffic
stations. After a station is searched, screen displays “TP”. Only when traffic information
is broadcasted can it be received, after traffic information is completed, the radio will
automatically switch to the previous mode.
OFF: Repress [TA] button to close TA function. In other modes, traffic announcement will
automatically switch to radio mode, after the traffic announcement is completed, it will
automatically switch to the previous mode.
1. Enter/exit
Touch [BT] icon in the main interface to enter the BT interface.
Touch icon to exit BT interface.
2. Pair/link
To use BT hand-free function, make connection first, i.e.
match the host with the BT mobile phone.
Operation methods:
Set the host to be matching state, and open the BT of
your mobile phone and use the mobile phone to search device, the mobile phone shall
prompt to match password with the BT when it has searched the BT device.
Input BT password (0000) to the mobile phone and confirm. The mobile phone shall
prompt whether authorize to this device, please select [Yes]. Phone and BT shall
automatically connect within 20 seconds. Under any working mode, the host shall
convert to BT state if there is an incoming call. And the host shall restore to current
mode after hanging up.
When the BT device matches with this device, the connection status shall display
“ LINK OK ”, otherwise, it shall display “ NO LINK ”.
3. Dialing
You can dial on mobile phone directly or input phone number through the number buttons
on the screen, click to delete if there is input error.
After input the phone number, click to make a call, and click to hang up the phone.
Click during a call so as to switch the voice between car speaker and mobile phone.
4. Call records
Click to access call records interface.
Touch this button to check all the phone numbers of received calls.
Touch this button to check all the dialed phone numbers.
Touch this button to check all the phone numbers of missed calls.
5. BT music
Click to access BT music interface.
10. AF
Touch the button to turn the AF function on/off. AF function is turned on, When the
received station signals become weak, the radio will automatically fine-tune to other
frequencies. When receiving an emergency announcing, the screen will display warning
message.
11. PTY
Touch the button the screen displays program types, users can search station according
to program type.
Note: If the unit does not have RDS function, it has no AF/TA/PTY function.
Previous song Play/Pause Next song
0807
Loading...