Bosch YS2180RA, YS2180RA5, YS2180RA5P, YS1780RA, YS1780RA5 Owner's Manual
...
Operating Instructions
GAS WATER HEATER
Owner’s Guide
Models YS2180RA YS2180RA5 YS2180RAP YS2180RA5P
YS1780RA YS1780RA5 YS1780RAP YS1780RA5P
WARNING
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury, or death.
- Do not store or use petrol or other flammable vapours and liquids in the
vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switches; Do not use electrical appilances,
including
the phone” inside the building.
• Immediately call you gas supplier, from a safe distance from the gas leak.
- To be installed and serviced only by an authorised person
- This appliance is not suitable for use as a pool heater
Thank you for purchasing this Bosch Gas Water Heater.
Before using, please:
Read this manual completely for operation instructions.
Confirm warranty and proof of purchase.
Keep this manual where it can be found whenever necessary.
Installation must conform with local codes, or in the absence of local codes, AS/NZS5601, AS/
NZS3500.4, AS3000 wiring regulations and all Local Building, Water and Gas fitting regulations.
Bosch
reserves the right to discontinue, or change at any time, the designs and/or specifications of
its products without notice.
* Note : This appliance requires a minimum flow rate to operate of 2.5 litres/min., water fixtures with a
flow rate of 7.5 litres/min. or higher are recommended.
For optimum performance we reommend installation of Bosch optional temperature controllers.
Robert Bosch (Australia) Pty. Ltd.
SBB80BU
Rev. 04/14
*SBB80BU*
Operating Instructions
Important Safety Information
To prevent damage to property and injury to the user, the icons shown below will be used to warn of
varying levels of danger.
Every indication is critical to the safe operation of the water heater and must be understood and observed.
Potential dangers from accidents during installation and use are divided into the following four
categories. Closely observe these warnings; they are critical to your safety.
Icons warning of risk level
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER indicates an imminently hazardous situation which,
DANGER
WARNING
if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION
Other icons
Electric
Shock.
Prohibited
Vapours from flammable liquids will explode and catch fire causing death or severe burns.
Prohibited
Do not use or store flammable products such as petrol, solvents or
adhesives in the same room or area near the water heater.
Keep flammable products:
1. Far away from the water
heater.
2. In approved containers.
3. Tightly closed.
4. Out of children’s reach.
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a potentially
hazardous situation which, if not avoided, may result in property damage.
High
Temperature.
No flame.
Be sure
to do.
Don’t
touch.
Earth
Don’t
disassemble
the equipment.
Don’t touch
with a wet
hand.
DANGER
Vapours:
1. Cannot be seen.
2. Vapours are heavier than air.
3. Go a long way on the floor.
4. Can be carried from other rooms
to the main burner by air currents.
Vapours
Hot Water Heater temperatures over 50 °C can cause severe burns instantly or
death from scalding.
Prohibited
Children, disabled and elderly are at the highest risk of being scalded.
Feel water temperature before bathing or showering.
Temperature limiting valves are available, ask licensed installer.
2
(Continued)
(Continued)
Operating Instructions
Do Not Install Indoors.
Prohibited
No flame.
This will cause carbon monoxide poisoning and a potential fire hazard.
WARNING
A. This water heater does not have a
pilot. It is equipped with an
ignition device that automatically
lights the burner. Do not try to
light the burner by hand.
B.
BEFORE OPERATING smell all
around the water heater area for
evidence of leaking gas. Be sure
to smell next to the floor because
some gas is heavier than air and
will settle on the floor.
WHAT TO DO IF YOU SMELL GAS.
• Do not try to light any
appliance.
• Do not touch any electrical
switch; do not use any phone
in your building.
•
Immediately call your gas
supplier.
Follow the gas supplier’s
instructions.
C. Use only your hand to turn the
gas valve knob. Never use tools.
If the knob will not turn by hand,
don’t try to repair it. Call a
qualified service technician.
Force or attempted repair may
result in a fire or explosion.
D. Do not use this water heater if
any part has been under water.
lmmediately call a qualified
service technician to inspect the
water heater and to replace any
damaged parts.
Be sure
Be sure
Temperature.
Be sure
When a gas leak is noticed:
1. Stop use immediately
2. Close the gas valve
to do.
3.
Contact your gas supplier immediately
If you detect abnormal combustion
or abnormal odours, or during an
earthquake, tornado or fire:
to do.
1. Turn off the hot water supply
2.
Turn off the power to the water heater
3.
Turn off gas and water supply valve.
4. Call the Bosch Helpline
AU 1300 30 70 37 NZ 0800 54 33 52.
Check the temperature
of the running hot water
before entering the
High
shower.
Check the temperature
before stepping into
the bath tub.
Leave the proper clearance between
the water heater and nearby objects
(trees, timber, boxes with flammable
to do.
materials etc.).
Left side:
Min. 500mm
Front:
Sug. 600mm
Indoor
Upper:
Min. 500mm
Right side:
Min. 500mm
(Continued)
3
Operating Instructions
Important Safety Information
(Continued)
Prohibited
Do not place the unit in an indoor environment by means of adding walls
and ceiling (Do not enclose using
corrugated sheets, etc.)
Unit
Carbon monoxide poisoning or fire may
occur as a result.
Be sure
Be sure the gas matches
the gas on the data
(inside of frontcover)
to do.
gas type label (right side
of casing).
Ex. For Natural Gas (YS2180RA)
plate
or
Prohibited
Prohibited
Prohibited
Prohibited
Carbon Monoxide Poisoning
Hazard. Do not install this water
heater in a mobile home, recreation
vehicle or on a boat.
Do not place combustibles such as
laundry, newspapers, oils etc. near
the heater.
Unit
Do not use combustible chemicals
such as oil, petrol, benzene etc. in
the near the water heater or the
exhaust vent.
Do not store or use petrol or other
flammable vapours and liquids in the
vicinity of this or any other appliance.
Be sure
to do.
Prohibited
Prohibited
Don’t touch
with a wet
hand.
Be sure
to do.
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
Do not use hair spray or spray
detergent in the vicinity of the
heater.
Do not allow small children to play
unsupervised in the bathroom.
Do not allow small children to
bathe unsupervised.
Do not touch the power
cord with wet hands.
Electric
Shock.
Contact Bosch before using with
a solar pre-heater.
Do not place or use a spray can
near the water heater or the exhaust
Prohibited
vent.
4
Don’t
disassemble
the equipment.
Contact a qualified service
technician for any necessary
repairs, service or maintenance.
Operating Instructions
CAUTION
Earth
Be sure
to do.
Prohibited
Prohibited
Be sure
to do.
Be sure to electrically earth the
unit.
Keep power cord free of dust.
Do not use the water heater for
other than hot water supply, shower
and bath.
Do not use a broken or modified power
cord. Do not bind, bend or stretch
power cords. Do not scratch, modify,
or subject them to impact or force.
To prevent burns or scalding, turn
off the power button and wait until
the equipment cools before performing maintenance.
Prohibited
Prohibited
Prohibited
Don’t
touch.
Do not turn off the water heater
while someone is bathing.
Do not cover the water heater, store
trash or debris near it, or in any way
block the flow of fresh air to the unit.
Do not install in locations where
excessive dust or debris will be
in the air.
Do not touch the exhaust vent
during or immediately after
operation of the water heater.
5
Operating Instructions
Important Safety Information
CAUTION
Do not drink water that has been inside the
unit for an extended period of time. Do not
drink the first use of hot water from the
unit in the morning.
Clean the filter on the water inlet as
frequently as required. The quality of your
local water will affect the frequency required.
Keep the area around the unit clean.
If boxes, weeds, cobwebs, cockroaches etc. are in
the vicinity of the unit, damage or fire can result.
Do not install the equipment where the
exhaust will blow on walls or windows.
Treat hard, acidic or otherwise impure
supply water with approved methods to
ensure full warranty coverage.
Problems resulting from scale formation
are not covered by the warranty.
Do not disassemble the remote controller.
Do not use benzene, oil or fat detergents
to clean the remote controller.
This may cause deformation.
Do not get the remote controller wet.
YPRS67XBN and YPRP62XBN are water resistant,
too much water can cause damage.
YPRM67XBN is not water resistant.
Do not splash water on the remote
controller. Do not expose the remote
controller to steam.
Do not locate the remote controller near stoves or
ovens, this may cause damage or failure.
Preventing damage from freezing ( p.22)
Damage can occur from frozen water within the
device and pipes even in warm environments.
Be sure to read below for appropriate measures.
Repairs for damage caused by freezing are not
covered by the warranty.
Do not run water through the unit when
unit is not on.
When discharging hot water, make sure the unit is ON.
If water is run through the unit with the unit
OFF, water may condense inside the unit and cause
incomplete combustion or damage to the internal
electrical components.
6
Power must be switched on at all times for
antifrost protection to work.
If it is snowing, check the air inlet, exhaust
gas vent and exhaust vent terminal for
blockage.
Do not use parts other than those specified
for this equipment.
Contents
Important Safety Information....................................................................... 2
Contents ........................................................................................................ 7
General Parts
Main Unit.................................................................................................... 8
Names and Functions of Controllers
Main Controller (YPRM67XBN) ................................................................ 9
Bathroom Controller (YPRS67XBN) ....................................................... 10
Operating Instructions
Sub Controller (YPRP62XBN) ................................................................. 11
Initial Operation ........................................................................................... 12
Clock Adjustment ........................................................................................ 13
Setting and Using the Water Heater........................................................... 14
Controller Priority Function ........................................................................ 16
Muting the Remote Controller .................................................................... 17
Bath Fill Function ........................................................................................ 18
Call Function ................................................................................................ 21
Frost Protection ........................................................................................... 22
Regular Maintenance................................................................................... 23
Troubleshooting .......................................................................................... 25
Follow-up Service ........................................................................................ 29
Specifications .............................................................................................. 30
Manufacturer’s Warranty ............................................................................ 35
7
Operating Instructions
General Parts
Main Unit
Outdoor Wall Mounted, Power flue Model
Flue Collar
Front Cover
Air Inlet
Water Drain Valve (with Water Filter)
(Inside Water Inlet) ( p.24)
Gas Supply Valve
Water Supply Valve
Hot Water Pipe
External Weatherproof Power Point
* The above illustration shows an example of installation.
The exact installation configuration may be slightly different.
8
Operating Instructions
Names and Functions of Controllers
Main Controller (YPRM67XBN) <Optional>
What is actually displayed depends on how the water heater is set.
Setting Buttons
For setting the hot
water temperature
( p.14 -15)
For other settings.
Display
Time Set Button
To set or lndicate Time
of day. ( p.13)
Bath Fill Volume Button
For setting the amount
of water that is delivered.
( p.18 -20)
* Before use, remove the protective sheet from the remote controller surface.
Display
The illustration below shows the remote controller display.
What is actually displayed depends on how the water heater is set.
Burner On Indicator
When burning, the
indicator is lit.
( p.15, 19)
Operation Button
For turning the water
heater on or off.
Bath Fill Button
To activate Bath Fill.
To set Bath Fill
temperature.
( p.18 -20)
Bath Fill Temperature Indicator
When this indicator is lit,
bath fill temperature is
displayed. ( p.18 -20)
Priority Indicator
When this indicator is lit,
the hot water temperature
can be set. ( p.16)
Error Code
A number will flash if
a failure occurs.
( p.28)
Clock
When Time Set button
is pushed, the clock is
displayed. ( p.13)
Temperature setting
(Eg.: 40°C)
Bath Fill Temperature setting
(Eg.: 40°C)
Bath Fill Volume setting
( p.18 -21)
9
Operating Instructions
Bathroom Controller (YPRS67XBN) <Optional>
What is actually displayed depends on how the water heater is set.
Setting Buttons
For setting the hot
water temperature
( p.14 -15)
For other settings.
Display
Call Button
To sound alarm at all
remote controls. ( p.21)
Priority Button
To transfer control from
another remote
( p.16)
* Before use, remove the protective sheet from the remote controller surface.
.
Display
The illustration below shows the remote controller display.
What is actually displayed depends on how the water heater is set.
Burner On Indicator
When burning, the
indicator is lit.
( p.15, 19)
Operation Button
For turning the water
heater on or off.
Bath Fill Button
To activate Bath Fill.
To set Bath Fill
temperature.
( p.18 -20)
Bath Fill Temperature Indicator
When this indicator is lit,
bath fill temperature is
displayed. ( p.18 -20)
Priority Indicator
When this indicator is lit,
the hot water temperature
can be set. ( p.16)
10
Error Code
A number will flash if
a failure occurs.
( p.28)
Temperature setting
(Eg.: 40°C)
Bath Fill Temperature setting
(Eg.: 40°C)
Bath Fill Volume setting
( p.18 -20)
Operating Instructions
Sub Controller (YPRP62XBN) <Optional>
What is actually displayed depends on how the water heater is set.
Display
* Before use, remove the protective sheet from the remote controller surface.
Display
The illustration below shows the remote controller display.
What is actually displayed depends on how the water heater is set.
Operation Button
For turning the water
heater on or off.
Setting Buttons
For setting the hot
Water temperature.
( p.14 -15)
Priority Indicator
When this indicator is lit,
the hot water temperature
can be set. ( p.16)
Burner On Indicator
When burning, the
indicator is lit.
( p.15, 19)
Temperature setting
(Eg.: 40°C)
Error Code
A number will flash if
a failure occurs.
( p.28)
11
Loading...