Bosch TPS110 EU User Manual
Parking Lot Sensor TPS110 EU
1 | 14
Parking Lot Sensor TPS110 EU
User manual
Parking Lot Sensor TPS110 EU
2 | 14
Table of contents
General description 3
Assembly and commissioning 3
Installation requirements ............................................................................................................................................. 3
Installing the sensor base ........................................................................................................................................... 3
Required material for installing the parking lot sensor ................................................................................................ 4
Preparation of the parking space ................................................................................................................................ 4
Installation of the sensor base .................................................................................................................................... 6
Installing the sensor .................................................................................................................................................... 8
Replacing/removing the BOSCH Parking Lot Sensor ................................................................................................. 9
Setup and operation of the parking lot sensor in the backend .................................................................................. 11
Technical specifications 11
Legal information 12
Disposal note in accordance with ElektroG and WEEE Directive 2012/19/EU ........................................................ 12
EU Declaration of Conformity .................................................................................................................................... 12
Note for transport ...................................................................................................................................................... 12
OSS note ................................................................................................................................................................... 13
Parking Lot Sensor TPS110 EU
3 | 14
1. General description
The TPS110 EU Parking Lot Sensor is used for detecting parked vehicles in parking lots. Only use the parking lot
sensor in conjunction with approved components.
2. Assembly and commissioning
1. Installation requirements
Before installing the sensors, make sure that the necessary infrastructure is working properly - make sure the
gateways are switched on, that a stable Internet connection has been established, and that there is a backend
connection. The backend, as well as the associated management software, must be functional. Make sure that all o fl
the required components (see Fig. 1 TPS110 EU sensor), as well as the tools, are ready.
Figure 1 TPS110 EU Sensor
2. Installing the sensor base
The sensor base is attached to the substrate (e.g., concrete, asphalt). To do this, we recommend a two-component
adhesive.
The adhesive is available in various package sizes (e.g., DELO®-PUR 9692; universal 2k polyurethane adhesive
available
in 50 ml and 200 ml cartridges); we would be happy to help with procurement. We recommend attaching several
sensor bases
first and only then installing the sensors.
1 Cap
2 Screw
4 Base (sensor base)
3 Core (sensor)
Parking Lot Sensor TPS110 EU
4 | 14
Required material for installing the parking lot sensor
Figure 2 Material for attachment
3. Disposable gloves (protection against contact with adhesive)
4. Two-component adhesive (here: DELO®-PUR 9692, 50 ml)
5. Adhesive press (these differ, depending on the cartridge size)
6. Mixing tip
7. Tape rule
8. Sensor base
9. Sensor core (sensor)
10. T20 screw
11. Sensor cap (sensor sealing cap)
Preparation of the parking space
The parking space must be free of dirt, dust, oil, water and other contaminants. For this purpose, at least one swept
area should be prepared. However, it is recommended to clean the surface to remove contamination using a highpressure cleaner and a burner.
The installation must take place in the center of the parking space (intersection of the two diagonals, see Fig. 3) in
order to ensure optimum sensor accuracy.
Figure 3 Determination of the center of the parking space
Parking Lot Sensor TPS110 EU
5 | 14
Figure 4 Available parking space for sensor installation
To provide the adhesive with a closed substrate, the surface intended for the installation of the sensor base should be
free of any gaps or misalignment (see Figure 4 Available parking space for sensor installation). This is crucial for the
contact surface and the adhesive effect of the sensor.
Figure 5 Substrate example (continuous) Figure 6 Substrate example (gap)
INFORMATION:
For the bonding procedure, please follow the instructions of the adhesive manufacturer (e.g.,
temperature, safety information and work instructions).
A parking space cleaning should be clarified in advance with the parking lot operator so that the
treatment does not result in removal of existing coatings.
Loading...