Bosch TDA7640GB User Manual

008 TDA76..GB/11/10

Customer Service

Great Britain

Bosch Customer Service

Grand Union House

Old Wolverton Road

Milton Keynes

MK12 5PT

UK [phone]

IRL [phone]

www.bosch-home.co.uk

Operating instructions

Solving Minor Problems Yourself

Problem Possible Causes Solution

Iron does not
work or is not
heating up

Temperature control (H) set to
minimum

Turn the temperature control to
the desired position

Connection problems Check that the plug is inserted

into the mains socket correctly

The automatic shut-off system
has been activated (*).

Move the iron gently from side
to side to re-start it

Iron is not
steaming

There is no water in the tank (E). Fill the water tank

The steam regulator (C) is in the

position

Set the steam regulator to the
relevant position

Water is
dripping from
the holes in the
soleplate

Temperature control (H) setting
is too low.

Set the temperature control
within the steam area (between

the “••” and “max”) or turn the

steam regulator (C) to

Steam regulator (C) is set too
high in conjunction with a low
temperature.

Turn the steam regulator to a
lower setting.

You have pressed the shot of
steam button (A) repeatedly
without waiting for 5 seconds
between each press

Wait 5 seconds between each
press of the jet of steam button

Water has been left in the tank
when the sole plate was cold,
with the steam regulator (C) set
at or

Always empty the tank after
ironing and set the steam
regulator to after ironing
and when filling the tank

Distilled water has not been
used (see “Filling the water

tank” section) or other products

such as fragrant water have
been added to the tank

Mix distilled water with tap

water as directed in the “Filling

the water tank” section and

never add any other products to
the water tank

Spray does
not work.

No water in the tank. Add water to the water tank.

Obstructed mechanism. Contact an Authorised

Technical Service Centre.

The iron
begins to
smoke when
switched on.

During first use: Certain
components on the appliance
have been lightly greased at the
factory and may produce a little
smoke when initially heated.

This is completely normal and
will stop after a short while.

Deposits come
out through
the holes in the
soleplate

Traces of lime scale are coming
out of the steam chamber

Carry out a cleaning cycle (see
Self Cleaning section)

Flashing lamp
on top of
handle (*)

Auto-shut off has been
activated.

Move the iron gently fromside
to side to re-start it. The lamp
will then flash once before it
re-heats

Thank you for buying the TDA76 steam iron from Bosch. These
instructions contain valuable information about the unique features
of this iron and some hints to make ironing easier for you.

Please visit www.bosch-home.co.uk for more product
information or to register your product, just follow the link to
the Online guarantee registration.

Before using the iron for the first time

Please carry out the following steps:

1. Remove the protective cover from the soleplate before using the
iron.

2. While the iron is unplugged, fill the water tank (E) with tap water

3. Plug the appliance into the mains and set the temperature control

(H) to the “max” position by lining it up with the pointer (G) on the

iron.

4. When the iron has reached the correct temperature, the pilot light (J)

goes out. Set the steam regulator (C) to the maximum position.

5. Hold the iron horizontally and repeatedly press the shot of steam
button (A). Any residue should come out of the soleplate (F). It may
smoke and smell – this is normal and will cease after a short while.

6. If necessary, carefully clean the soleplate down with a dry, folded
cloth

Cleaning and Maintenance

Attention ! Risk of burns !

For general cleaning, follow the information below:

Problem Solution

Dirty/lightly marked
iron body or soleplate

Clean the body of iron or soleplate with a
damp cloth then dry it.

Mark develops on
soleplate during use

Set the iron to its maximum temperature

setting. Rub the iron a few times over with
a dry cotton cloth folded several times.

Heavily stained
soleplate

While the iron is cold, iron a linen cloth
soaked in white vinegar. Then dampen a
cloth with water and wipe the soleplate
clean and dry thoroughly.

DO NOT de-scale or clean the water tank with cleaning products
or solvents, as these could cause the iron to drip when using the
steam function.

DO NOT use a “professional steam cleaner” for cleaning the

appliance.
DO NOT use sharp objects or abrasive products to clean the soleplate or
any other part of the appliance. To keep the soleplate in good condition,
do not allow it to come into contact with metal objects.

GUARANTEE TERMS

The terms of the guarantee for this appliance are in accordance with
that stated by our representative for the country in which it is sold.
Details of those conditions can be obtained from the retailer from
whom the appliance was purchased. The SALES RECEIPT must
be presented when making any claims against the terms of this
guarantee. We reserve the right to make technical modifications.

Environmental Care

This iron has been designed according to ecological criteria,
related to the sustainable development, analyzing its whole
lifecycle - from material selection to its later reusing or recycling

- evaluating the improvement possibilities, from a technical,
economical and environmental point of view.

Before throwing a used appliance away, you should make it
noticeably inoperable e.g. cut off the mains lead and be certain to
dispose of it in accordance with current laws and regulations.

Your retailer, town council or local council can give you detailed
information about these.

This appliance is labelled in accordance with
European Directive 2002/96/EG concerning
used electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).

The guideline determines the framework for the return
and recycling of used appliances as applicable throughout
the EU.

Tips to help you save energy

Steam production consumes the most energy. To help
minimise the energy used, follow the advice below:

• Start by ironing the fabrics that require the lowest ironing

temperature.

• Regulate the steam according to the selected ironing

temperature.

• Only use steam if necessary. If possible, use the spray

function instead.

• Try to Iron the fabrics while they are still damp and reduce

the steam setting. Steam will be generated from the
fabrics rather than the iron. If you tumble dry your fabrics
before ironing them, set the tumble drier to the ‘iron dry’
programme.

• If the fabrics are damp enough, turn off the steam regulator

completely.

• Stand the iron upright during pauses. Resting it horizontally

with the steam regulator on generates wasted steam.

Important

This appliance has been designed exclusively for domestic use

and must not be used for industrial purposes.

Carefully read through the operating instructions for the appliance
and safeguard them for future reference.

General safety warnings

• Danger of electric shocks or fire!

• This appliance is to be connected and used in accordance with

the information stated on its characteristics plate.

• This appliance must be connected to an earthed socket. If
it is absolutely necessary to use an extension cable, make

sure that it is suitable for 16A and has a socket with an earth
connection.

• The iron should not be used if it has been dropped, if there

are visible signs of damage or if it is leaking water. It must be
checked by an authorized Technical Service Centre before it
can be used again.

• Do not allow the power cable to come into contact with the

soleplate when it is hot.

• In order to avoid that, under unfavourable mains conditions,

phenomena like transient voltage drops or lighting fluctuations
can happen, it is recommended that the iron is connected to a
power supply system with a maximum impedance of 0.27Ω . If
necessary, the user can ask the public power supply company
for the system impedance at the interface point.

• This appliance is not intended to be used by persons (including

children) with reduced physical, sensory or mental capacities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning the use of the appliance
by a person responsible for their safety.

• Keep the appliance out of children’s reach.

• Children should be supervised to ensure that they do not play

with the appliance.

• Remove the plug from the socket before filling the appliance with

water or before pouring out the remaining water after use.

• The appliance must be used and placed on a stable surface.

• When placed on its stand, make sure that the surface on which

the stand is placed is stable.

• The iron must not be left unattended while it is connected to

the supply mains.

• Unplug the appliance from the mains supply after each use, or

if a fault is suspected.

• The electrical plug must not be removed from the socket by

pulling the cable.

• Never immerse the iron in water or any other fluid.

• Do not leave the appliance exposed to weather conditions (rain,

sun, frost, etc.)

• With the aim of avoiding dangerous situations, any work or

repair that the appliance may need, e.g. replacing a faulty mains
cable, must only be carried out by qualified personnel from an
Authorised Technical Service Centre.

TDA 76..

sensixx B7

* Model dependent

You can download this manual from the local homepages of Bosch

m

a

x

Using Your Iron

1. Your iron

m

a

x

max.

M.Auto shut off
indicator lamp*

E. Water tankF. Soleplate

A. Shot of steam

D. Spray outlet

C. Steam regulator

B. Spray button

* Model dependent

L. Power cable

J. Pilot light

G. Pointer

I. Max. Water

H. Temperature control

K. Water tank cover

N. "Clean" button

2. Filling the water tank

Set the steam regulator (C) to the position and

unplug the iron from the mains!

Use only clean water from the tap without mixing anything with

it. The addition of other liquids, such as perfume, will damage
the appliance.

Any damage caused by the use of the aforementioned
products, will make the guarantee void.

Do not use condensation water from tumble dryers, air conditioners
or similar appliances. This appliance has been designed to use
normal tap water.

To prolong the optimum steam function, mix tap water with distilled
water 1:1. If the tap water in your district is very hard, mix tap

water with distilled water 1:2.
You can inquire about the water hardness with your local water
supplier
To prevent spillage of water out of the appliance in vertical position,

never fill beyond the «max» water level mark!

7. Ironing without steam

This function enables the iron to be used for dry ironing.

1. Set the steam regulator (C) to the position.

2. Select an appropriate temperature for the type of material being
ironed.

8. Spray

This can be used to remove stubborn wrinkles.

1. Do not use the spray function with silk as staining may occur.

2. Make sure that there is water in the tank (E).

3. When ironing, press the spray button (B) and water will spray
out of the spray outlet (D) onto the garment.

9. After finishing each ironing session

1. Unplug the iron from the mains socket.

2. Set the steam regulator (C) to the position.

3. Open the water tank cover (K).

4. Hold the iron with the point facing up and shake it gently until
all the water has come out.

5. Set the iron aside in a vertical position to cool down.

6. Coil the power cable (L) loosely around the heel of the iron,
before storing.

7. Store the iron in an upright position.

10. Self Cleaning

The self clean function helps remove lime scale that has built
up around the steam valve.

This should be performed once every 3 or 4 uses.

1. When the iron is cold, slide the steam regulator (C) between the

and positions in quick succession about 3 or 4 times to

help loosen any lime scale and clean the valve inside.

2. Heat up the iron. Before starting ironing, hold the iron horizontally
over a sink and press the shot of steam button (A) 3 or 4 times.
This will help force out any lime scale and dirt deposits through
the holes in the soleplate.

11. Multiple de-scaling system

This range of irons is equipped with the following de-scaling
features “AntiCalc”.

A. self-clean

Each time you use the steam regulator (C), the “self-clean” system

cleans the mechanism of any scale deposits.

B. calc‘n-clean

The “calc’nclean” function helps to remove scale particles out
of the steam chamber. Use this function approximately every 2

weeks, if the water in your area is very hard.

1. Unplug the iron from the mains socket, set the steam regulator
(C) to the position and fill the water tank (E) with water.

2. Set the temperature selector (H) to the “max” position and plug

in the iron.

3. After the necessary warm-up period, the pilot light (J) goes out.
Then, unplug the iron.

4. Hold the iron over a sink. Press the “clean” button (N) and gently

shake the iron. Boiling water and steam will come out, carrying
scale or deposits that might be there.

5. When the iron stops dripping, release the button, plug the iron in
and heat it up again until the remaining water has evaporated.

6. Repeat the process if the iron still contains impurities.

m

a

x

C. anti-calc cartridge

The anti-calc cartridge has been designed to reduce the build-

up of scale produced during steam ironing, helping to extend
the useful life of your iron. Nevertheless, the “anti-calc” cartridge

cannot remove all of the scale that is produced naturally over
time.

12. Anti-drip system

The irons in this range are equipped with an anti-drip system.
This will automatically stop the iron producing steam when the

selected temperature setting is too low to prevent water from
dripping out of the soleplate. You may hear a clicking sound when
this system is in operation.

Additional Features (Model Dependent)

Auto shut-off

Some irons in this range are equipped with an auto-shut off system.

The “secure” auto shut-off function switches off the iron

automatically when it is not being used, thus helping to prevent
accidents and saving energy. When the appliance is first plugged
in, this function will be inactive for the first 2 minutes to allow it to
reach the set temperature.

If during ironing, the iron is not moved for a certain length of time,
the iron will automatically switch off. The length of time will depend
on the position the iron has been left in:

Horizontally (flat) or on its side: 30 seconds
Vertically (upright): 8 minutes
The pilot light on the top of the handle (M) will flash when auto

shut-off has been activated. To switch the iron back on, move it
gently from side to side. The light will stop flashing.

Fabric protection soleplate cover (“protect”)

Some irons in this range are equipped with a fabric protection
soleplate cover

The fabric protector is used for steam-ironing delicate garments

at maximum temperature without damaging them. Use of the

protector also does away with the need for a cloth to prevent
shine on dark materials.

It is advisable to first iron a small section on the inside of the
garment to see if it is suitable.

To attach the fabric protection soleplate cover to the iron, place
the tip of the iron into the end of the fabric protector and press
the rear of the protector upward until you hear a click. To release
the fabric protector, pull down on the clip at the rear and remove
the iron.

The protective cover can be purchased from After-sales or the
Bosch e Shop.

Accessory code

(After-sales)

Name of accessory:

Protect cover soleplate

(Bosch e Shop)

464851 TDZ1510

4. Ironing with steam

The steam regulator (C) is used to adjust the amount of
steam produced when ironing.

1. Make sure that there is water in the tank (E).

2. Adjust the temperature setting and then set the steam regulator
according to the table below. Steam will automatically be
produced:

Temperature Setting Steam Regulator Setting

••• to “max”

••

Note: At a temperature setting of “•”, the soleplate is not hot

enough to produce steam so the steam regulator should be set
to the position to avoid water dripping from the soleplate (F).

5. Ironing with shot of steam

This can be used to remove stubborn wrinkles or to press
in a sharp crease or pleat. It cannot be used on a synthetic
setting for delicate items.

1. Set the temperature control (H) to the “•••” or “max”

position.

2. Set the steam regulator (C) to the position.

3. Press the shot of steam (A) button on the handle repeatedly at
intervals of 5 seconds.

6. Vertical steaming with shot of steam

This can be used to remove creases from hanging clothes,
curtains etc. It cannot be used on a synthetic setting for
delicate items.

WARNING! Do not vertical steam while the item is being worn.

Never spray or aim steam at people or animals!

1. Make sure that there is water in the tank (E).

2. Set the temperature control (H) to the «•••» or «max» position

and the steam regulator (C) to the position.

3. Hold the iron in an upright position about 15 cm away from the
garment being steamed.

4. Press the shot of steam button (A) on the handle at intervals of
5 seconds, however, after 4 jets of steam, wait for 10 seconds
to allow for continued steam production.

3. Setting the temperature

The temperature control (H) adjusts the temperature of the
soleplate (F).

1. Check the temperature instructions shown on the care label of
the garment you are ironing and set the temperature control
(H) to the corresponding position by lining it up with the pointer
(G) on the iron:

Fabric Temperature Setting

Synthetics •

Silk - Wool ••

Cotton - Linen •••

m

a

x

max.

min

max

2. If you are unsure what type of material the garment is made from,
start ironing on the lowest temperature setting and increase

accordingly. If the garment is made from mixed fabrics, set the

temperature for the most delicate material.

3. For silk, woollen or synthetic materials iron the reverse side
of the fabric to prevent shiny patches. Avoid using the spray
function to prevent stains.

4. Sort your garments based on their care labels, always
starting with clothes that have to be ironed at the lowest
temperature.

5. The pilot lamp (J) will stay lit while the iron is heating up and go
out once the selected temperature has been reached. Wait a
few seconds after the lamp goes out before you start ironing.

Once the iron is ready, you can continue to iron even if the pilot

lamp comes on again.

6. If your iron has auto shut-off and the pilot light (M) is flashing,
the auto shut-off has activated. Gently move the iron side to
side to restart it.