WARNING: A risk of fire and electrical shock exists in all electrical appliances and may
cause personal injury or death.
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all instructions before using the kitchen machine.
2. To protect against risk of electric shock, do not put the drive unit in or under water or
other liquid.
3. This appliance is not for use by children.
4. Close supervision is necessary when any appliance is used near children.
5. Do not leave appliances unattended during operation.
6. Unplug from outlet when not in use, before putting on or taking off parts and
before cleaning.
7. To disconnect: switch appliance off then remove plug from power supply.
8. Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas
and other utensils away from whisks, beaters, blades, disc, dough hook and/or other
moving parts during operation to reduce the risk of injury to persons and/or
damage to the appliance or its attachments.
9. Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions or is dropped or damaged in any manner. Return appliance to the
nearest authorized service facility for examination, repair or electrical or mechanical
adjustment.
10. The use of attachments not recommended or sold by the appliance manufacturer
may cause fire, electric shock or injury and is therefore prohibited.
11. Do not use outdoors or when standing in a damp area.
12. Do not let cord hang over edge of table or counter, or touch hot surfaces.
13. Always operate appliance with covers in place.
14. Blades are sharp. Handle carefully due to risk of injury.
15. Remove beaters from mixing bowl before washing.
NOTE: ALSO BE SURE TO READ THE WARNINGS AND CAUTIONS THAT ARE
PROVIDED BEFORE EACH ATTACHMENT’S OPERATING INSTRUCTION.
SAVE THESE INSTRUCTIONS
2
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS .................................................................. 2
Table of contents ..................................................................................... 3
ABOUT YOUR KITCHEN MACHINE ....................................................... 4
The Concept 7400 ................................................................................... 4
SPECIAL ACCESSORIES ..................................................................... 21
Important Notes ..................................................................................... 22
BOSCH Small Appliance Warranty ......................................................... 23
HOUSEHOLD USE ONLY
3
ABOUT YOUR KITCHEN MACHINE
Congratulations on having selected the
Bosch Concept 7400 Kitchen Machine —
the finest interpretation of the Concept
Series of kitchen machines that we and—
thankfully—cooking professionals the world
over, feel are the best household-type
kitchen machines available.
b. Six-quart capacity stainless steel
mixing bowl (MUZ 7 ER1) with cover
with integral filling tube and filling funnel/
cap.
c. Dough hook
d. Twin beating whisks
e. Six-cup capacity stainless steel
blender (MUZ 7 MX3)
f. Motor drive cover
As you read through these instructions,
please pay particular attention to the
IMPORTANT SAFEGUARDS. Specific
safeguards for the attachments, as well as
warnings and cautions, are provided in each
section describing the operation of that
particular attachment.
The Concept 7400
The MUM 7400 UC stainless steel kitchen
machine includes the following components,
see figure 1:
a. MUM 7400 UC stainless steel,
electronic power unit
Unpacking
Carefully remove the power unit from its
packaging and place it on the counter so it
is ready to use. As you remove the
accessories from the carton, check them
against figure 1 to assure that all the
standard parts are present.
Electrical Specifications
Check to make sure that the voltage on
which your Concept 7400 is to operate is
the same as specified on the rating plate.
Standard North American models have an
Figure 1.
4
electrical power rating of 700-watt maximum
power rating with the accessory attachment
that draws the most power (some accessory
attachments may draw less power).
making disks and grater attachment. See
SPECIAL ACCESSORIES at the back of
this booklet, page 21. Or, to view all currently
available accessories, visit our Web site at
Before Using for the First Time
Before using any of the attachments for the
first time, it is recommended they be
washed, rinsed well and dried. Of the
attachments supplied, all parts, except the
blender’s blade/base assembly, are
dishwasher safe:
> The blender’s blade/base assembly
should be washed under running water
and dried.
Note: It is recommended that the blender’s
blade/base assembly never be left to
stand in water or soap solution, to prevent
the bearing lubricant from being washed out.
Getting to Know Your Bosch Kitchen
Machine
The Bosch Concept 7400 Kitchen Machine
comes with attachments shown in figure 1,
however, in addition to the attachments that
come with the MUM 7400 UC, Bosch offers
many special accessories.
Special Accessories
To allow you to get the most service from
your Bosch Concept 7400 Kitchen Machine,
Bosch engineers have designed a line of
special accessories to expand the
usefulness of your machine. In addition to
the attachments that come with the MUM
7400 UC, there are optional special
accessories that can be ordered separately.
These accessories include a food and meat
grinder, grain mills, citrus juicer and ice
cream maker, plus additional attachments
that can be used with the meat grinder:
fancy cookie attachment, fruit pulper, pasta-
www.boschsmallappliances.com
Work on expanding the usefulness of the
Bosch Kitchen Machine is a continuing
process. If there is some type of accessory
in which you are interested in, that is not
included at the back of the book, please
either write us at:
•Bosch Small Appliances
Customer Support
BSH Home Appliances
5551 McFadden Avenue
Huntington Beach, CA 92649
or call us at:
•1 (866) 44BOSCH
[1 (866) 442-6724]
Power Unit Features
The MUM 7400 UC power unit has the
following features, refer to figure 2:
700-watt motor
The most powerful motor offered with any
household kitchen machine.
Electronic speed control
Six-position rotary switch is located at front
of power unit: 4 speeds plus a momentary
pulse function and a stop position, “O/Off,”
see figure 2a.
Timer Control
The Bosch exclusive electronic timer is
controlled by four buttons, see figure 2b.
The timer can be set to operate the Concept
7400 for up to 30 minutes. Timing is
displayed in the digital display.
5
Electronic Safety Control
Monitors the power unit to assure that it is
functioning properly. Provides automatic
shutdown in case of interruption of the power
supply, stalled motor or motor overload.
Digital LED Display
Multifunction digital display, see figure 2c:
1. Speed Display
The speed selected is displayed as
bars across the top of the digital
display: A single bar is illuminated for
speed 1, two bars speed 2, etc.
2. Time Display
Time selected when using the timer
control is displayed and counts down
when timer is in use.
3. Error Reporting
Displays error message if there is a
problem that has caused the electronic
safety control to be activated. See
TROUBLESHOOTING section for error
codes.
Motor drive cover
Used to cover mono drive when not in use,
see figure 2d.
Mono drive
Four electronically controlled shaft speeds
are all available from a single location; each
attachment automatically connects to the
appropriate drive speed, figure 2e.
Gentle start
a special feature that brings the motor up
to speed over a two-second period; limiting
splashing.
Convenient cord storage
Convenient cord storage is located on the
back of the power unit, see 2f.
Integrated hand grips
Side recesses provide for easy lifting and
carrying of power unit when not in use, see
2g.
Figure 2.
6
Four rubber feet
Four rubber feet with formed suction cups
provide the ultimate in stability, while also
serving to isolate the power unit from the
hard surface to minimize noise and
vibration. Need clean smooth surface, see
figure 2h.
AttachmentPages
Mixing bowl w/dough hook ....... 9
Mixing bowl w/twin whisks ....... 11–14
Blender ..................................... 15
Table 1.
–11
–17
Getting Started
The operation of your Bosch Concept Series
Kitchen Machine is summarized below.
Specific instructions for using each of the
attachments, provided with Bosch Concept
7400 Kitchen Machine follow this summary.
Please read the specific instructions
thoroughly before using that attachment,
paying particular attention to the
IMPORTANT SAFEGUARDS and
WARNINGS provided.
1.Place power unit on suitable work
surface.
Before using the machine with any of
the attachments, the power unit should
be placed on a suitable work surface.
The surface should be sturdy, smooth
and clean; make sure that there is no
flour or oil on the surface. A clean
smooth surface will provide the best
footing for the suction cup feet on
the power unit and will limit slipping
and/or “walking.”
2.Plug power unit into power supply.
Unwind the power unit’s cord to
appropriate length and plug it into
a convenient nearby receptacle.
3.Remove motor drive cover.
Remove motor drive cover from monodrive.
5.Operate unit
Once the attachment is in place, the
power unit may be operated. The
power may be manually turned on and
off using the rotary switch or operating
time may be controlled using the timer.
Using the timer
The operation of the power unit can
be set to turn off automatically after a
set time (maximum on time is 30
minutes). The length of time of
operation may be selected with the
appliance either already on and
running, or with rotary switch in Off,
“O/Off,” position; power unit must,
however, be plugged in.
To use timer function:
1. Turn on the timer function by
depressing the “time on” button,
see figure 2b. The display will show
minutes and seconds separated by
a colon. The initial display will be
“00:00” with the separating colon
flashing.
2. Select the operating time desired
by pressing the “+” button to
increase the time in 10-second
increments or the “-” button to
decrease the time in 10-second
increments.
4.Select the attachment to be used.
Select attachment you wish to use
and place on power unit. See specific
instructions for attachment selected.
Specific instructions are located on
pages listed below:
Holding either button down for more
than 2 seconds will cause the time
to increase or decrease rapidly.
Also, if the running time desired is
close to 30 minutes, the timer can
quickly be set to 30 minutes by
7
depressing the “-” button after first
selecting the timer function. The
time could then be adjusted down
from 30 minutes by depressing the
“-” button.
Using the Rotary Switch
Once the attachment is in place, the
speed of its moving components can
be controlled through the use of the
rotary switch at the front of the power
unit. See figure 2a. The rotary switch
has six positions:
a. “M,” a momentary “pulse” position
that provides full speed and power
for the time it is held in position.
b. “O/Off,” the Off position.
c. Four speeds labeled 1, 2, 3 and 4.
Speed 1 is the lowest speed. The
speed increases with each
succeeding step up to the highest
speed, speed 4. The selected
speed is also indicated by the bar
at the top of the digital display, see
figure 2c, 1. The bar is broken into
four separate segments. For Speed
1 a single segment is illuminated,
for Speed 2 two segments are
illuminated. This continues until
Speed 4 when all four segments at
the top of the display are
illuminated.
Timer with Rotary Switch
If the timer function had been turned
on prior to switching the power unit on
and setting the speed with the rotary
switch, the power unit will run for the
time selected and then turn itself off.
The digital display will show “00:00”
and the colon between the minutes and
seconds, as well as the four speed
segments, will flash. The rotary switch
should then be turned to the Off
position, “O/Off.” The timer will
automatically turn itself off.
Interrupting or Pausing Timer
The timer function may be interrupted
or paused at anytime by turning the
rotary switch to the Off position, “O/
Off.” The operating time will stop at
the current time. To restart simply turn
the rotary switch back on to the
desired speed. The appliance will then
continue to operate for the remaining
time or until again interrupted.
Stopping Timer Function
The timer function can be turned off at
any time by depressing the “time off”
button, see figure 2b. If the rotary
switch is On, the power unit will
continue to run at the selected speed
until turned off manually.
Electronic Safety Control
The Bosch Concept 7400 Kitchen
Machine incorporates an electronic
safety control to protect the motor. If
the safety becomes activated, the
power unit will shutoff and an error
code will be displayed, see figure 2c,
3. See TROUBLESHOOTING at the
back of this manual if the electronic
safety control should become
activated.
6.Turn power unit off.
When your work with the attachment
is completed or the capacity of the
batch-feed attachment has been
reached, turn the power unit to the Off
position, “O/Off.” If you are using the
timer function, turning the rotary
switch to Off will stop the timer at the
amount of time remaining.
7. Remove the attachment.
Remove the attachment from the
power unit, per instructions for the
specific attachment being used.
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.