The Photobeam 5000 Series consists of the single
channel quad beam ISC-FPB1-W60QS, ISC-FPB1W120QS, ISC-FPB1-W200QS, and the four channel
quad beam ISC-FPB1-W60QF, ISC-FPB1-W120QF, and
ISC-FPB1-W200QF detectors with separate
transmitters and receivers.
The detector series uses four pulsed infrared beams
that are designed to activate an alarm when all four
beams are simultaneously blocked. False alarm
immunity is increased by the utilization of four beams
compared to single or dual beam models.
The detector series also features interlocked upper
and lower beams, signal voltage LED, and optional
environmental discrimination circuitry.
System overview
Consisting of a separate transmitter and receiver, it is
designed to activate an alarm when an intruder passes
within the direct line of sight between the transmitter
and receiver.
Functions
Mounting features
Mounting and installing the detector is now easier
than ever. Install the detector through easy-to-use
mounting hole locations which provide an enlarged
entry point of access to accept small to large, single or
multiple cable set wires. Fastening screw locations
eliminate the need for unnecessary crawling or
bending during installation.
Configure the detectors for up to four different
channels. This allows multiple units to be used near
one another without the possibility of receiver crosstalk. This is particularly useful when stacking multiple
beam sets.
High Density mode (4-channel models only)
The High Density mode allows you to add an additional
zones of protection to detect larger objects that only
partly interrupt the beams of individual devices. This
feature allows an alarm condition to be generated
when beam pairs are interrupted on adjacent devices
but not all four beams are interrupted on one device.
2 | Photobeam 5000
Selectable AND/OR mode (4-channel models only)
This feature allows an added level of detection by
generating an alarm when four beams from two units
are blocked simultaneously. Environmental conditions
require higher false alarm tolerance against smaller
objects passing through the detector's line of sight. To
do this, set the AND/OR gate option to AND gate mode
that only causes an alarm condition when all four
infrared beams are interrupted simultaneously.
High Security applications might require the detection
of smaller objects passing through the detector's line
of sight. To do this, set the AND/OR gate option to OR
gate mode that causes an alarm condition when either
the upper two beams or the lower two beams are
interrupted.
Dust/insect cover features
The included foam sealing ensures that the detectors
are properly secured from insects and other
environmental elements such as humidity and
temperature fluctuations.
The improved cover design includes water flow
channels to prevent water and dirt from accumulating
in front of optic components, and eliminates the need
for additional weatherproofing solutions.
Environmental Discrimination Circuit
Monitors gradual loss of signal due to dust, fog, rain,
and snow. Normally closed output opens when signal
loss reaches 90%. May be field configured to bypass
alarm relay when activated.
Beam Power Control
The transmitter power output is field adjustable
allowing the user to eliminate reflections and crosstalk from other units.
This feature improves catch performance and false
alarm immunity, and allows for reliable installation in
most applications.
Test features
High visibility reception level LED improves ease of
installation. Flash rate increases as installation
alignment improves.
Voltage output terminals also allow for improved
alignment accuracy.
Optical module alignment switch to allow for
independent adjustment of upper and lower beam
pairs.
Dual Modulated beam
The Dual Modulated Beam eliminates interference
from external noise sources such as sunlight, car
headlights, electrical interference, etc.
Certifications and approvals
RegionCertification
EuropeCEEMC, RoHS [ISC-FPB1-W60QF, ISC-
CEEMC, RoHS [ISC-FPB1-W60QS, ISC-
FPB1-W120QF, ISC-FPB1-W200QF
with or wihout BH12T heater]
FPB1-W120QS, ISC-FPB1-W200QS
with or without BH12T heater]
Technical specifications
Photobeam
ISC-FPB1-
W60QS
Maximum
indoor range
Maximum
outdoor range
* Single channel quad beam series
ISC-FPB1-
Maximum
indoor range
Maximum
outdoor range
* Four channel quad beam series
120 m
(393 ft)
60 m
(196 ft)
W60QF
120 m
(393 ft)
60 m
(196 ft)
ISC-FPB1W120QS
240 m
(787 ft)
120 m
(393 ft)
ISC-FPB1W120QF
240 m
(787 ft)
120 m
(393 ft)
ISC-FPB1W200QS
400 m
(1312 ft)
200 m
(656 ft)
ISC-FPB1W200QF
400 m
(1312 ft)
200 m
(656 ft)
Environmental considerations
Operating temperature-25°C to +60°C (-13°F to +140°F) (96%
or less)
Storage temperature/
humidity
IP rating (indoor)IP66
-30°C to +70°C (-22°F to +158°F)
Relative Humidity 96%
Mounting considerations
LocationPole mount or surface mount
Horizontal adjustability±90°
Vertical adjustability±10°
Distance between upper
and lower lens
245 mm (9.64 in)
Dimensions
Dimensions103 mm x 398 mm x 99 mm
(4.05 in. x 15.66 in. x 3.89 in.)
3 | Photobeam 5000
Power requirements
ISC-FPB1-
W60QS
Current draw90 mA95 mA100 mA
* Single channel quad beam series
ISC-FPB1-
W60QF
Current draw120 mA124 mA128 mA
* Four channel quad beam series
Voltage10.5 VDC to 28 VDC.
Alarm outputForm C relay (COM, NC, NO) (dry contact)
EDC outputForm B, normally closed relay (dry-contact)
Duration – Open when EDC is active
Contact capacity - DC30V, 0.2A (resistive
load)
Resistance - 3.0 Ω or less
ISC-FPB1W120QS
ISC-FPB1W120QF
ISC-FPB1W200QS
ISC-FPB1W200QF
Interruption time
Interruption
time
40 ms – 500 ms (adjustable)
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and
must be treated accordingly.
Ordering information
ISC-FPB1-W60QS
Single channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 60
m (196 ft) max outdoor range, 120 m (393 ft) max
indoor range.
Order number ISC-FPB1-W60QS
ISC-FPB1-W120QS
Single channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 120
m (293 ft) max outdoor range, 240 m (787 ft) max
indoor range.
Order number ISC-FPB1-W120QS
ISC-FPB1-W200QS
Single channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 200
m (656 ft) max outdoor range, 400 m (1312 ft) max
indoor range.
Order number ISC-FPB1-W200QS
ISC-FPB1-W60QF
Four- channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 60
m (196 ft) max outdoor range, 120 m (393 ft) max
indoor range.
Order number ISC-FPB1-W60QF
ISC-FPB1-W120QF
Four- channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 120
m (293 ft) max outdoor range, 240 m (787 ft) max
indoor range.
Order number ISC-FPB1-W120QF
ISC-FPB1-W200QF
Four- channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 200
m (656 ft) max outdoor range, 400 m (1312 ft) max
indoor range.
Order number ISC-FPB1-W200QF
Accessories
BH12T Photobeam Heater
Reduces the effects of frost, intense fog, cold, and
damp conditions on photoelectric beam detectors.
Shipped in packages of two.
Order number BH12T
ISC-FPB1-W30DS Photoelectric Detector
Provides an outdoor range of 30 m (100 ft) and an
indoor range of 60 m (200 ft).
Order number ISC-FPB1-W30DS
ISC-FPB1-W60DS Photoelectric Detector
Provides an outdoor range of 60 m (200 ft) and an
indoor range of 120 m (400 ft).
Order number ISC-FPB1-W60DS
ISC-FPB1-W90DS Photoelectric Detector
Provides an outdoor range of 90 m (300 ft) and an
indoor range of 180 m (600 ft).
Order number ISC-FPB1-W90DS
4 | Photobeam 5000
ISC-FPB1-W60QS
Single channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 60
m (196 ft) max outdoor range, 120 m (393 ft) max
indoor range.
Order number ISC-FPB1-W60QS
ISC-FPB1-W120QS
Single channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 120
m (293 ft) max outdoor range, 240 m (787 ft) max
indoor range.
Order number ISC-FPB1-W120QS
ISC-FPB1-W200QS
Single channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 200
m (656 ft) max outdoor range, 400 m (1312 ft) max
indoor range.
Order number ISC-FPB1-W200QS
ISC-FPB1-W60QF
Four- channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 60
m (196 ft) max outdoor range, 120 m (393 ft) max
indoor range.
Order number ISC-FPB1-W60QF
MP3 L‑Curved Metal Pole
Curved metal poles for mounting to vertical surfaces
for pole mounting photoelectric detectors. Shipped in
packages of two.
Order number MP3
PC1A Weather Enclosure
Protects detectors when mounted outside. The
enclosure’s dimensions are 39.4 cm x 10.3 cm x 6 cm
(15.5 in. x 4 in. x 2.4 in.). Shipped in packages of two.
Order number PC1A
PC3A Back‑to‑back Box
Allows back-to-back mounting of detectors on a pole.
Shipped individually.
Order number PC3A
ISC-FPB1-W120QF
Four- channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 120
m (293 ft) max outdoor range, 240 m (787 ft) max
indoor range.
Order number ISC-FPB1-W120QF
ISC-FPB1-W200QF
Four- channel quad-beam photoelectric detector
designed for indoor and outdoor applications.
Consisting of a separate transmitter and receiver. 200
m (656 ft) max outdoor range, 400 m (1312 ft) max
indoor range.
Order number ISC-FPB1-W200QF
MP1 Metal Pole, 1 m (3 ft)
Straight metal poles measuring 1 m (3 ft) for pole
mounting photoelectric detectors. Shipped in
packages of two.
Order number MP1
MP2 Metal Pole, 1.2 m (4 ft)
Straight metal poles measuring 1.2 m (4 ft) for pole
mounting photoelectric detectors. Shipped in
packages of two.
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
apr.securitysystems@bosch.com
www.boschsecurity.asia
Bosch (Shanghai) Security Systems Ltd.
203 Building, No. 333 Fuquan Road
North IBP
Changning District, Shanghai
200335 China
Phone +86 21 22181111
Fax: +86 21 22182398
www.boschsecurity.com.cn
Robert Bosch Ltda Security Systems Division
Via Anhanguera, Km 98
CEP 13065-900
Campinas, Sao Paulo, Brazil
Phone: +55 19 2103 2860
Fax: +55 19 2103 2862
latam.boschsecurity@bosch.com
www.boschsecurity.com