Bosch GGS Professional 8 CE, GGS Professional 28 C, GGS Professional 28 CE, GGS Professional 28 LC, GGS Professional 28 LCE User Manual

OBJ_DOKU-22619-003.fm Page 1 Thursday, December 16, 2010 4:03 PM

Robert Bosch GmbH

Power Tools Division
70745 Leinfelden-Echterdingen
Germany

www.bosch-pt.com

3 609 929 C06 (2010.12) O / 302 UNI

GGS Professional

8 CE | 28 C | 28 CE | 28 LC | 28 LCE

de Originalbetriebsanleitung
en Original instructions
fr Notice originale
es Manual original
pt Manual original
it Istruzioni originali
nl Oorspronkelijke

gebruiksaanwijzing

da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet

el Πρωτότυπο οδηγιών χρήσης

tr Orijinal işletme talimat

pl Instrukcja oryginalna
cs Původní návod k používání
sk Pôvodný návod na použitie
hu Eredeti használati utasítás

ru Оригинальное руководст-

во по эксплуатации

uk Оригінальна інструкція з

експлуатації

ro Instrucţiuni originale

bg Оригинална инструкция

sr Originalno uputstvo za rad
sl Izvirna navodila
hr Originalne upute za rad

et Algupärane kasutusjuhend
lv Instrukcijas oriģinālvalodā
lt Originali instrukcija

ar
fa

Ϡλ΍ έΎ ίήσ ΎϤϨϫ΍έ

ΕΎϤϴϠόΗϞϴϐθΘϟ΍ΔϴϠλϷ΍

OBJ_BUCH-1269-003.book Page 3 Thursday, December 16, 2010 4:05 PM

3 |

GGS 8 CE

GGS 28 LC

GGS 28 LCE

Professional

6

5

2 4

13

GGS 28 C
GGS 28 CE
Professional

A

3 609 929 C06 | (16.12.10) Bosch Power Tools

8

2

3
9

7

OBJ_BUCH-1269-003.book Page 15 Thursday, December 16, 2010 4:05 PM

English | 15

Safety Notes

General Power Tool Safety Warnings

WARNING

the warnings and instructions may result in elec­tric shock, fire and/or serious injury.

Save all warnings and instructions for future
reference.

The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.

1) Work area safety
a) Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power

tools create sparks which may ignite the
dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

2) Electrical safety
a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified

plugs and matching outlets will reduce
risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, radia­tors, ranges and refrigerators. There is

an increased risk of electric shock if your
body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges and moving parts.

Damaged or entangled cords increase the
risk of electric shock.

Read all safety warnings and all
instructions. Failure to follow

e) When operating a power tool outdoors,

use an extension cord suitable for out­door use. Use of a cord suitable for out-

door use reduces the risk of electric
shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a residual cur­rent device (RCD) protected supply. Use

of an RCD reduces the risk of electric
shock.

3) Personal safety
a) Stay alert, watch what you are doing and

use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the influ­ence of drugs, alcohol or medication. A

moment of inattention while operating
power tools may result in serious person­al injury.

b) Use personal protective equipment. Al-

ways wear eye protection. Protective

equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protec­tion used for appropriate conditions will
reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before
connecting to power source and/or bat­tery pack, picking up or carrying the
tool. Carrying power tools with your fin-

ger on the switch or energising power
tools that have the switch on invites acci­dents.

d) Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of
the power tool may result in personal inju­ry.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unex­pected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, clothing
and gloves away from moving parts.

Loose clothes, jewellery or long hair can
be caught in moving parts.

Bosch Power Tools 3 609 929 C06 | (16.12.10)

OBJ_BUCH-1269-003.book Page 16 Thursday, December 16, 2010 4:05 PM

16 | English

g) If devices are provided for the connec-

tion of dust extraction and collection fa­cilities, ensure these are connected and
properly used. Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care
a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better
and safer at the rate for which it was de­signed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the
switch is dangerous and must be re­paired.

c) Disconnect the plug from the power

source and/or the battery pack from the
power tool before making any adjust­ments, changing accessories, or storing
power tools. Such preventive safety

measures reduce the risk of starting the
power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfa­miliar with the power tool or these in­structions to operate the power tool.

Power tools are dangerous in the hands of
untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,
breakage of parts and any other condi­tion that may affect the power tool’s op­eration. If damaged, have the power tool
repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp
cutting edges are less likely to bind and
are easier to control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these in­structions, taking into account the work­ing conditions and the work to be per­formed. Use of the power tool for

operations different from those intended
could result in a hazardous situation.

5) Service
a) Have your power tool serviced by a qual-

ified repair person using only identical
replacement parts. This will ensure that

the safety of the power tool is maintained.

Safety Warnings for Straight Grinders

Safety Warnings Common for Grinding, Wire
Brushing, Polishing or Carving:

f This power tool is intended to function as a

grinder, carving tool, polisher (GGS 8 CE)
or wire brush (GGS 8 CE). Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool. Failure to follow all instructions listed

below may result in electric shock, fire
and/or serious injury.

f Do not use accessories which are not spe-

cifically designed and recommended by the
tool manufacturer. Just because the acces-

sory can be attached to your power tool, it
does not assure safe operation.

f The rated speed of the accessory must be at

least equal to the maximum speed marked
on the power tool. Accessories running fast-

er than their rated speed can break and fly
apart.

f The outside diameter and the thickness of

your accessory must be within the capacity
rating of your power tool. Incorrectly sized

accessories cannot be adequately controlled.

f The arbour size of wheels, sanding drum or

any other accessory must properly fit the
spindle or collet of the power tool. Accesso-

ries that do not match the mounting hard­ware of the power tool will run out of bal­ance, vibrate excessively and may cause loss
of control.

f Mandrel mounted wheels, sanding drums,

cutters or other accessories must be fully
inserted into the collet or chuck. The “over­hang” or the length of the mandrel from the
wheel to the collet must be minimal. If the

mandrel is insufficiently held and/or the
overhang of the wheel is too long, the mount­ed wheel may become loose and ejected at
high velocity.

3 609 929 C06 | (16.12.10) Bosch Power Tools