Bosch F220-135, F220-190F, F220-135F Specsheet

Fire Alarm Systems | F220 Heat Detectors

F220 Heat Detectors

www.boschsecurity.com

u Two-wire or four-wire bases

u 50 ft (15.2 m) maximum spacing between detectors

u Visible identification of model: F220‑135 = no ring,

F220‑135F = gray ring, F220‑190F = black ring

The F220 Heat Detectors include:

• F220‑135: An electronic rate-of-rise, fixed
temperature heat detector that initiates an alarm
when the ambient temperature exceeds +135°F
(+57°C) or when the ambient temperature increases
by +15°F (+8.3°C) or more in less than 1 minute

• F220‑135F: An electronic fixed temperature heat
detector that initiates an alarm when the ambient
temperature reaches +135°F (+57°C).

• F220‑190F: An electronic fixed temperature heat
detector that initiates an alarm when the ambient
temperature reaches +190°F (+88°C).

The detectors use low current electronic circuitry, so
they can connect to 12 VDC nominal or 24 VDC
nominal power source circuits. When mounted on the
appropriate F220‑B6 Series Mounting Base, the F220
Heat Detectors provide general property protection
from fire.

Notice

Heat detectors are not life safety devices.

u Tamper detection

u Dual color LED

Functions

Compatible Bases

Configure the detectors as either two-wire or four-wire
depending on the mounting base selected. These
detectors are compatible with any of the F220‑B6
bases:

• F220‑B6 12/24 VDC Two-wire Mounting Base

• F220‑B6R Standard 12/24 VDC Four-wire Mounting
Base

• F220‑B6RS 24 VDC Four-wire Mounting Base with
Sounder

• F220‑B6C 12/24 VDC Four-wire Mounting Base with
Auxiliary Form C Relay

• F220‑B6E 12/24 VDC Four-wire Power Supervision
Mounting Base

• F220‑B6PM 24 VDC Four-wire Addressable Master
Base

• F220‑B6PS 12/24 VDC Four-wire Addressable Base

Dual-color LED

To verify the detector has power and the heat
detection circuitry functions, a dual-color LED
indicator flashes green every 8 sec when operating
normally. It flashes once every 4 sec when a trouble
condition exists. The LED latches on red if an alarm

2 | F220 Heat Detectors

occurs, allowing the user to easily verify individual
detector alarms. Clear the alarm condition by
interrupting power to the detector.

Tamper Detection

When detector heads are correctly installed in any of
the F220‑B6 bases, the control panel initiates a
trouble signal if a detector is removed from its base. A
mechanical tamper lock comes with each base to
inhibit unauthorized head removal.

Supervision

The control panel supervises two-wire systems.
Supervision of four-wire system power is provided by
an end-of-line (EOL) power supervision device such as
a D275 or PAM-4, or an F220‑B6E Power Supervision
Mounting Base and an EOL resistor as specified by the
control panel manufacturer.

Certifications and approvals

Region Certification

Europe CE 89/336/EEC, EN50130-4/A Sept 1998,

USA UL UQGS: Heat - Automatic Fire Detectors

FM F220 Heats

CSFM see our website

NYC­MEA

MSFM 2200 Sep 2008

Hong Kong HKFSD J-002/C/067

EN61000-6-3 Oct 2001

(UL521)

117-05-E

Installation/configuration notes

Compatible Control Panels

Addressable Systems: These detectors are compatible
with addressable systems controlled by D9412GV2,
D7412GV2, D9412G, or D7412G Control Panels or the
D9124 Fire Alarm Control Panel when used with the
F220‑B6PM or F220‑B6PS Addressable Detector
Bases.
Two-wire: Bosch Security Systems, Inc. makes no
claim written, oral, or implied that these detectors
work with any two-wire control panels except those
specified in the Control Panel Compatibility chart in
the Technical Service Note (P/N: 4998148185).
Four-wire: Thes detectors are compatible with all UL
Listed four‑wire control panels. For proper end-of-line
(EOL) resistor selection, see the control panel's
installation instructions.

Mounting the Bases

Depending on local regulations, the bases can be
surface mounted directly on four-inch square or
octagonal electrical boxes and single-gang switch
boxes.

Notice

The volume of any electrical box used should be
adequate to accommodate the number and size of
conductors as specified by the National Electrical
Code or any local authorities having jurisdiction
(AHJ).

End-of-Line Power Supervision

Loop supervision requires one D275 or PAM-4 or
F220‑B6E per loop when using F220‑B6R/B6C bases
and is accomplished by the control panel.

Wiring the Bases

For detailed wiring instructions, see the F220 Series
Detectors with F220‑B6/C/E/R Bases Installation
Instructions, the F220 Series Detectors with
F220‑B6RS Bases Installation Instructions, or the
F220‑B6PS/M Installation Instructions.

Parts included

QuantityComponent

1 Detector head with dust cover

Technical specifications

Electrical

Current (alarm):
(detector head only)

Current (start‑up
\standby):

Maximum RMS Ripple: 25% of DC input

Power-up Time: 22 sec maximum

Voltage (standby)

F220‑B6: 8.5 VDC to 32.0 VDC

F220‑B6C/‑B6R/‑B6E: 10.0 VDC to 30.0 VDC

F220‑B6RS: 16.0 VDC to 30.0 VDC

F220‑B6PM: 18.9 VDC to 28.0 VDC

F220‑B6PS: With D299: 18.9 VDC to 28.0 VDC

20 mA minimum at 8.5 VDC;
35 mA maximum at 32 VDC

0.12 mA maximum at 35 VDC

Without D299: 9.6 VDC to 28.0 VDC

Environmental

Relative Humidity: 0% to 95% non-condensing

Notice

Consult NFPA 72 for proper detector placement.

Temperature
(normal operating):

Note: The normal environment where these detectors are installed
should be within the specified normal operating temperature limits.

+32°F to +100°F (0°C to +38°C)

3 | F220 Heat Detectors

Mechanical

Color: White

Dimensions
(diameter x H):

6.75 in. x 2.25 in. (17.1 cm x 6.4 cm)

Trademarks

All hardware and software product names used in this
document are likely to be registered trademarks and
must be treated accordingly.

Ordering information

F220‑135 Electronic Rate‑of‑Rise/Fixed Temperature
(+135°F [+57°C]) Heat Detector

Rate‑of‑rise/fixed temperature heat detector head
only; requires base.

Order number F220-135

F220‑135F Electronic Fixed Temperature (+135°F
[+57°C]) Heat Detector

Fixed temperature heat detector head only; requires
base.

Order number F220-135F

F220‑190F Electronic Fixed Temperature (+190°F
[+88°C]) Heat Detector

Fixed temperature heat detector head only; requires
base.

Order number F220-190F

Accessories

D275 Power Supervision Module

Line supervision device for four-wire fire detection
circuits

Order number D275

F220‑B6C 12/24 VDC Four‑wire Base with Auxiliary
Form C Relay

Four‑wire base with a normally‑open (NO) alarm loop
relay and a set of auxiliary contacts (Form C).

Order number F220-B6C

F220‑B6E 12/24 VDC Four‑wire Power Supervision Base
with End‑of‑line Power Monitoring Relay

Four‑wire base with a normally‑open (NO) alarm relay
and an EOL power supervision relay.

Order number F220-B6E

F220‑B6PM 24 VDC Four‑wire Addressable Multiple De­tector Base

The multiple detector base provides an address on the
FACP data expansion circuit for its detector and up to
an additional 19 detectors. It accepts the F220
Photoelectric Smoke Detector Heads and Heat
Detector Heads.

Order number F220-B6PM

F220‑B6PS 12/24 VDC Four‑wire Addressable Single De­tector Base

The single detector base provides an address on the
FACP data expansion circuit for its detector. It accepts
the F220 Photoelectric Smoke Detector Heads and
Heat Detector Heads.

Order number F220-B6PS

DRA‑5 Remote Annunciator (5 VDC)

Designed to provide remote annunciation of alarms for
a number of Bosch smoke and heat detectors

Order number DRA-5

DT‑2 Detector Removal Tool

Use the DT‑2 to remove, replace, or test the detector
head

Order number DT-2

F220‑B6 12/24 VDC Two‑wire Base

Standard base for two‑wire (12 VDC or 24 VDC
system) applications.

Order number F220-B6

F220‑B6R Standard 12/24 VDC Four‑wire Base

Standard base for four‑wire (12 VDC or 24 VDC)
detector systems.

Order number F220-B6R

F220‑B6RS 24 VDC Four‑wire Detector Base with Soun­der

Four-wire detector base with sounder for use with the
F220 Photoelectric Smoke and Heat Detectors.

Order number F220-B6RS

4 | F220 Heat Detectors

Represented by:

Americas: Europe, Middle East, Africa: Asia-Pacific: China: America Latina:

Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.us

Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: [phone]
[e-mail]
www.boschsecurity.com

Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.asia

Bosch (Shanghai) Security Systems Ltd.
203 Building, No. 333 Fuquan Road
North IBP
Changning District, Shanghai
200335 China
Phone [phone]
Fax: [phone]
www.boschsecurity.com.cn

Robert Bosch Ltda Security Systems Division
Via Anhanguera, Km 98
CEP 13065-900
Campinas, Sao Paulo, Brazil
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.com

© Bosch Security Systems 2015 | Data subject to change without notice
2701717003 | en, V8, 27. Jul 2015