Bosch D1260, D1260B User Manual 2

Download

Page 1

D1260/D1260B

Owner's Manual

Keypad

Page 2

D1260/D1260B | Owner's Manual

This system includes a telephone line seizure feature. The system may be programmed to communicate with a central monitoring station to report system events. You will not be able to use your phone while the system is communicating with the central monitoring station. In the unlikely event that the central station is not able to receive the report, your phone may be unavailable for up to 20 minutes while the panel makes additional communication attempts.

Some commands listed below may not be available. Contact your security company for more information.

Contents

Introduction .....................................................................5

Your Keypad .....................................................................5

About This Owner’s Manual ........................................... 6

Part I: Security system basics .......................................7

Using the keypad ..............................................................7

Command center keys......................................................7

Points 8

What is a Point? ................................................................8

Controlled Points ..............................................................8

24-Hour Points ..................................................................8

Your Custom Display.......................................................8

View Faulted or Bypassed Points....................................9

To automatically scroll faulted or bypassed points.......9

Warning Displays and Tones ........................................10

Keypad Quiets for Keystrokes.......................................10

Priority of Events ............................................................10

Fire Alarms ......................................................................11

Silencing Fire Alarms .....................................................11

Burglary Alarms ..............................................................12

Silencing Burglary Alarms .............................................12

Fire Trouble and Fire Supervisory Events...................13

Silencing Fire Trouble and Fire Supervisory conditions 13

Special Fire Trouble and Fire Supervisory Display....13

Viewing Fire Trouble and Fire Supervisory conditions 13

Non-Fire Trouble and Supervisory Events ..................13

Silencing Non-Fire Trouble and Supervisory Events .13

Special System Trouble Display....................................13

Cleared Events Are Not Lost.........................................13

Entry Delay Tone and Display......................................14

Exit Delay Tone and Display ........................................14

Keystroke Checking Tones............................................14

Silencing an Alarm .........................................................14

To SILENCE an alarm:..................................................14

How Your System Reports Alarms...............................14

Part II: System Commands......................................... 15

Entering a Passcode........................................................ 15

Turning On the System (Arming)................................. 16

To Turn Your Security System On (Arm):.................. 16

Turning Off the System (Disarming)............................ 16

To Turn Your Security System Off (Disarm):............. 16

Turning On the System (Arming) With a Duress

Passcode........................................................................... 16

Turning On the System (Arming) With Doors or

Windows Open............................................................... 17

MASTER ARM ? (COMMAND + 1)......................... 19

Description ...................................................................... 19

Using Master Arm:......................................................... 19

Master Arming all Areas ............................................... 20

MASTER ARM INST ? (COMMAND + 1 + 1) ....... 21

PERIMETR INST (COMMAND + 2)........................ 22

Turn On the Perimeter With No Delays..................... 22

Using Perimeter Inst: ..................................................... 22

PERIMETR DELAY ? (COMMAND + 3) ................ 23

Turn On the Perimeter With Delays............................ 23

Silence the Trouble Sounder & Clear Trouble Display

(COMMAND + 4) ......................................................... 24

Description ...................................................................... 24

Using COMMAND 4:................................................... 24

VIEW MEMORY ? (COMMAND + 4 + 0).............. 24

View Event Memory...................................................... 24

Using View Memory: .................................................... 24

WALK TEST ? (COMMAND + 4 + 4)...................... 25

Walk Test ........................................................................ 25

RESET SENSORS ? (COMMAND + 4 + 7) ............. 27

Reset Sensors .................................................................. 27

Using Reset Sensors:...................................................... 27

WATCH MODE ? (COMMAND + 6)....................... 28

Watch Mode ................................................................... 28

Entering Watch Mode: .................................................. 28

Exiting Watch Mode:..................................................... 28

PERIMETR PART ? (COMMAND + 8).................... 29

Partially Turn On the Perimeter................................... 29

Using Perimetr Part:....................................................... 29

2 Bosch Security Systems | 9/04 | 50410D

Page 3

Special Alerts (COMMAND + 7 and COMMAND +

9) 30

Using COMMAND 7:....................................................30

Using COMMAND 9:....................................................31

Part III: Advanced Commands..................................32

Advanced Commands....................................................32

Terms Used in This Section...........................................32

BYPASS A POINT? (COMMAND + 0)....................33

Description.......................................................................33

Using Bypass a Point ......................................................33

UNBYPASS A POINT? (COMMAND + 0 + 0)........35

Description.......................................................................35

Using Unbypass a Point:................................................35

SEND REPORT ? (COMMAND + 4+1 or 4+2).......36

Description.......................................................................36

Using Send Report..........................................................36

REMOTE PROGRAM ? (COMMAND + 4 + 3)......38

Description.......................................................................38

For systems without a phone number...........................38

For systems with a phone number or network

connection........................................................................39

CHANGE TIME/DATE (COMMAND + 4 + 5) ......40

DOOR CONTROL (COMMAND + 4 + 6) ..............41

Description.......................................................................41

Using Door Control........................................................41

Access Level ....................................................................43

CHANGE DISPLAY (COMMAND + 4 + 9) ............44

Brighten/Dim Display ....................................................44

Show Continuous Time/Date........................................44

EXTEND CLOSING (COMMAND + 5 + 1)............45

CHG SKEDS ? (COMMAND + 5 + 2).......................47

Description.......................................................................47

Using Chg SKEDS..........................................................47

DEL USER ? (COMMAND + 5 + 3) ..........................50

CHG RELAYS ? (COMMAND + 5 + 4)....................51

CHG PASSCODES ? (COMMAND + 5 + 5)............51

Description.......................................................................51

Using Chg Passcodes......................................................52

ADD/CHANGE USER (COMMAND + 5 + 6)........53

DEFAULT TEXT ? (COMMAND + 5 + 7)...............60

FIRE TEST ? (COMMAND + 5 + 8)..........................61

DISPLAY REV ? (COMMAND + 5 + 9)...................62

SERVICE MENU ? (9 + 9 + Enter).............................63

Using View Log ..............................................................64

Using Print Log ...............................................................65

Using Display Rev ..........................................................65

Using Service Walk Test................................................65

D1260/D1260B | Owner's Manual | Contents

Using Default Text ......................................................... 66

Using Setup ..................................................................... 66

Part IV: Multi-Area Use.............................................. 68

Working with Multiple Areas from a Single Command Center 68

View Area Status ............................................................ 68

View Point Status............................................................ 69

MOVE TO AREA ? (COMMAND + 5 + 0)............. 70

Turning On the System ................................................. 71

Turning on Selected Areas............................................ 71

Turning on Multiple Areas with a Passcode ...............71

Faulted Points in Other Areas....................................... 72

Turn On the Entire System Without Delays............... 72

Turning on All or Selected Areas................................. 72

Turning Off the System ................................................. 73

Turning Off Multiple Areas with a Passcode.............. 73

Turning Off Multiple Areas with Disarm All.............. 73

Turning Off Selected Areas........................................... 74

Appendix ....................................................................... 76

Supplementary Information for Adding Passcodes.... 76

User Authority Levels.................................................... 76

Passcode Worksheet....................................................... 76

User Interface.................................................................. 76

User Interface.................................................................. 77

User (Passcode) Worksheet (User 000 to 038) ............ 78

♦ User (Token) Worksheet (User 000 to 038)

D9412G/D7412G Only................................................. 79

User (Passcode) Worksheet (User 039 to 075) ............ 80

♦ User (Token) Worksheet (User 039 to 075)

D9412G/D7412G Only................................................. 81

User (Passcode) Worksheet (User 076 to 114) (101-249

= D9412G only).............................................................. 82

♦ User (Token) Worksheet (User 076 to 114) D9412G/D7412G Only (101-249 = D9412G only) ... 83

User (Passcode) Worksheet (User 115 to 150) (101-249

= D9412G only).............................................................. 84

User (Token) Worksheet (User 115 to 150) (101-249 =

D9412G only) .................................................................85

User (Passcode) Worksheet (User 151 to 189) (101-249

= D9412G only).............................................................. 86

User (Token) Worksheet (User 151 to 189) (101-249 =

D9412G only) .................................................................87

User (Passcode) Worksheet (User 190 to 226) (101-249

= D9412G only).............................................................. 88

♦ User (Token) Worksheet (User 190 to 226) D9412G/D7412G Only (101-249 = D9412G only) ... 89

User (Passcode) Worksheet (User 227 to 249) (101-249

= D9412G only).............................................................. 90

Bosch Security Systems | 9/04 | 50410D 3

Page 4

D1260/D1260B | Owner's Manual Contents

User (Token) Worksheet (User 227 to 249) (101-249 =

D9412G only)..................................................................91

User (Passcode) Worksheet (Blank) ..............................92

User (Token) Worksheet (Blank)...................................93

Security System Limitations...........................................93

Fire Safety and Evacuation ............................................94

Standard Displays ...........................................................95

System Trouble Displays................................................96

Security System Glossary...............................................98

Maintenance and Service...............................................99

How to Clean the Command Center ...........................99

Your Alarm Company ...................................................99

Figures

Figure 1: D1260/D1260B front panels......................5

Figure 2: D1260/D1260B Digital Keypad ................6

Figure 3: Using soft keys for display menus .............6

Figure 4: Smoke Detector Locations (Plan View)..94 Figure 5: Smoke Detector Locations (Elevation

View)...........................................................94

Figure 6: Escape Route .............................................94

Tables

Table 1: D1260/D1260B Keypad keys ....................7

Table 2: Keypad Commands ..................................15

Table 3: Door Status.................................................42

Table 4: Sked Table..................................................49

Table 5: Screen Area Definitions............................69

4 Bosch Security Systems | 9/04 | 50410D

Page 5

D1260/D1260B | Owner's Manual | Contents

Introduction

Your security system helps to secure life, property, and investments against fire, theft, and bodily harm. The keypad is an advanced digital device that offers a variety of features not available with other systems. Its highly visible, backlit keypad and built-in sounder alert you to a number of system events. A familiar ATM style design and ease-of-use make it ideal for property monitoring.

Your Keypad

Your Keypad is composed of two main sections: the numeric keypad section and the display/selection keys (also referred to as “soft keys”).

Figure 1: D1260/D1260B front panels

1 - LCD Display 2 - Digital Keypad

D1260B

D1260

3- Soft Keys 4 - Keypad Function Keys

Bosch Security Systems | 9/04 | 50410D 5

Page 6

D1260/D1260B | Owner's Manual | Introduction - About This Owner’s Manual

The numeric keypad section is a standard 3x4-keypad matrix that should be very familiar to you. It has been designed to closely resemble that of a standard telephone with the numeric keys of 1-0; and * and # keys. The display is an easy-to-read 4 line by 20character liquid crystal display that becomes backlit when a key is pressed or a system event occurs.

Figure 2: D1260/D1260B Digital Keypad

• Advanced Commands: Allow users to perform

advanced system functions like add and delete user passcodes, reassign authority levels to user passcodes and operate or change programmed scheduled events (Skeds) from the keypads. As you make changes to the system, update the information contained in the tables in this guide to provide an accurate account of the programmed information.

• Multi-Area Use: Each of the functions described

in the preceding section on Advanced Commands is presented as though your system includes only one area. If your system includes more than one area, it can be set up one of two ways by the installing company: (1) Each keypad will only have

D1260 D1260B

The soft keys are used to make selections when the display shows an arrow pointing next to it. For example, the display shown to the right is what will appear when there are faulted points in your system.

access to the local area to which it is assigned, or (2) Each keypad may access either some or all areas beyond the one to which it is assigned.

• Appendix: Covers the limitations of a Security

System, Fire Safety and Evacuation, Maintenance and Service of your Security System and How to

Clean the Keypad. Pressing the soft key adjacent to the View Points> display will then begin to scroll the faulted point(s) in your system.

Figure 3: Using soft keys for display menus

About This Owner’s Manual

This owner’s manual is divided into five main sections:

• Security System Basics: Covers how to use the

Keypad, the various keys on the Keypad, what a “Point” is and the various types of Points, and custom displays.

• System Commands: This section covers system

commands, such as turning the system on and off, resetting sensors, etc. Your security company programs the functions described in this section. Some of them may not be included in your system. Some of the functions covered may require you to enter your personal passcode.

6 Bosch Security Systems | 9/04 | 50410D

Page 7

Part I: Security system basics

D1260/D1260B | Owner's Manual | Part I: Security system basics

Using the keypad

Your security system provides quick access to functions by pressing the COMMAND key and one or two additional keys.

D1260 D1260B

Another way to access functions is through the Command Menu. To access the Command Menu, press the soft key adjacent to

Menu>

shown in the

display.

Pressing the

<Previous

Next>

soft key while in the Menu List allows you to scroll up or down through the list of functions programmed by your security company.

Command center keys

Pressing the soft key adjacent to the function being displayed initiates the function.

<Exit

To exit the Command Menu, press the

soft key.

Use the Command Menu to locate functions you don’t use often or that don’t have a command number.

Table 1: D1260/D1260B Keypad keys

Key

D1260 D1260B

Name Description

COMMAND Use the COMMAND key in combination with one or two numeric keys to perform

ENTER The ENTER key is used to complete the entry of your passcode at the command

EXIT When Exit> or <Exit appears in the keypad display, pressing the soft key

a function

enter. Whenever a function requires that you enter your passcode at the keypad, first press the digits of the code and then press the ENTER key. Your system will not recognize your passcode until you press ENTER.

adjacent to it will bring you one level up in the function or will exit you out of the function you are in.These functions may be displayed on either side of the display.

When viewing a list, pressing the <Previous soft key will take you back to the previously shown item.

Press the Next> soft key to pass over the present item(s) in a menu or function.

Bosch Security Systems | 9/04 | 50410D 7

Page 8

D1260/D1260B | Owner's Manual | Part I: Security system basics - Points

Points

What is a Point?

A “point” is a detection device, or group of devices connected to your security system. Points display individually at the keypad with custom text. The text can describe a single door, motion sensor, smoke detector, or an area such as UPSTAIRS or GARAGE. There are two basic types of points, controlled and 24hour.

Controlled Points

Controlled points respond to alarm conditions depending upon whether the system is turned on (armed) or turned off (disarmed). Controlled points are programmed to respond instantly to alarm conditions or to provide a delay for you to reach the keypad and disarm the system.

The type of alarm appears before the point text when there is an alarm. There are two types of controlled points, perimeter points and interior points.

Perimeter Points

These points usually include all exterior doors and windows of the building.

Interior Points

These points usually include interior forms of burglary detection devices, such as motion sensors, or inside doors, for example.

24-Hour Points

24-hour points are always on, even when the burglary system is disarmed (turned off). There are two types of 24-hour points, fire points and non-fire points.

Fire Points

Fire points exclusively monitor fire detection devices. They are always armed and cannot be disarmed. You can clearly distinguish fire points from other non-fire points at the keypad.

When there is a fire alarm, the display shows the following:

*FIRE ALARM* is displayed on the first line, text identifying the point as a fire point is displayed on the second line, and instructions for silencing the alarm are displayed on the third and fourth lines.

Fire alarms have a unique audible warning signal.

Non-Fire Points

Non-fire 24-hour points are always armed and cannot be disarmed.

Your Custom Display

“At an idle state” means that the system is not currently performing a function entered by a user. There are three idle states the system may be in:

• Turned on (Armed)

• Turned off (Disarmed) with no points faulted

(doors or windows open) in the area

• Turned off with faulted points (doors or windows

open) in the area.

8 Bosch Security Systems | 9/04 | 50410D

Page 9

D1260/D1260B | Owner's Manual | Part I: Security system basics - View Faulted or Bypassed Points

This manual uses the default idle state displays for examples of these idle states. Your security company may have programmed custom text for the idle displays in your system. The custom text and the default text for the three system idle displays follow.

Default Text Custom Text Area Name Text

Appears on the top line of the display

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Throughout this manual, all examples of “AREA # NAME TEXT” will use “AREA 1 WAREHOUSE.” The actual name of Area 1 will differ depending on the specifics of your system.

Area Is On Text

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

The Silence> soft key is only shown when the keypad buzzer is active

Area Off Text

Indicates the area is turned off (disarmed). 24-hour points remain armed.

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Area Not Ready Text

Indicates that the area is turned off, but not ready to arm.

View Faulted or Bypassed Points

To properly arm your system, all the doors and windows in the system must be in the normal (not faulted) condition. Viewing the faulted points helps you find faulted points and correct them so proper arming is possible.

Your keypad offers two ways of displaying faulted and bypassed point information. The first causes the faulted or bypassed point information to scroll automatically through the display. The second allows you to manually scroll through each individual point description.

To automatically scroll faulted or bypassed points

1. Ensure your keypad shows idle text.

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

2. Press any number key. The text for Area 1 is

displayed first followed by the number (#) of faulted points on the next line

3. The display changes to show the point text

description of the faulted points. If there is more than one faulted point, the display will automatically cycle through all of them before returning to idle text.

These displays scroll at the rate of 3 seconds each.

The View Points> soft key may be displayed on the third line of the keypad if there are faulted points.

Bosch Security Systems | 9/04 | 50410D 9

Page 10

D1260/D1260B | Owner's Manual | Part I: Security system basics - Warning Displays and Tones

4. The display returns to idle text after scrolling

through the faulted and bypassed point information.

Warning Displays and Tones

Your keypad emits one of several distinct tones and displays custom text to alert you to system events. Additional bells or sirens may also be connected to your system. Bells or sirens mounted on the exterior of your premises alert neighbors to emergencies and provide an audible guide for police and fire fighters.

The View Points> soft key will be shown when there are faulted points.

To manually scroll faulted or bypassed points:

5. Ensure your keypad shows idle text.

6. Press the View Points> soft key to display the first

faulted point.

Keypad Quiets for Keystrokes

Pressing any key on the keypad lights the keys and quiets any warning tones. If you don’t press another key within 20 seconds, the keypad lights go out and the warning tones resume.

Priority of Events

If more than one event occurs, your system sorts them into one of four groups. The groups (highest priority first) are:

• Fire Alarms

• Burglary Alarms

Press the Next> soft key or the <Previous soft key repeatedly to display the faulted and bypassed point information.

• Fire Troubles and Fire Supervisory conditions

• Non-Fire Troubles and Non-Fire Supervisory

conditions.

The group with the highest priority scrolls first in the keypad’s display. Descriptions of the tones and displays for each group and instructions for silencing the tones are included in the descriptions that follow.

If faulted or bypassed points in other areas exist, then the display changes to show these points before returning to idle text.

10 Bosch Security Systems | 9/04 | 50410D

Page 11

D1260/D1260B | Owner's Manual | Part I: Security system basics - Fire Alarms

3 seconds

Fire Alarms

Fire alarms are the highest priority events. When a fire point activates, your keypad emits a pulsating highpitched fire tone. Evacuate all occupants and investigate for smoke or fire. Ensure that all occupants know the difference between the burglary tone and the fire tone. The tone sounds for the time set by your security company.

Silencing Fire Alarms

Entering a personal passcode with the proper authority level silences a fire alarm and disarms the system if it was armed.

The system will now display * second line and

Clear Display>

Then the number of points in alarm (

ALARMS NAME TEXT

points in alarm (

) and then the area text appears (

) followed by the custom text of all the

SMOKE DETECTOR

of occurrence. If there is more than one point causing an alarm, the

display will show each point for three seconds before showing the next one.

When the last alarm is shown, the next display is the idle text. The cycle is repeated until COMMAND 4 is pressed.

Alarm Silenced*

on the

appears on the fourth.

# FIRE

AREA 1

), in the order

Your system may be programmed so that you cannot silence some fire alarms until the fire event clears. Entering COMMAND 4 clears the scrolling point text from the display.

The *

Alarm Silenced*

message will continue to alternate with idle text as a reminder that it is still possible to view the text of the points in alarm by using the View Memory function. See

VIEW MEMORY ?

(Command 40) for more information.

To clear the event memory and remove the *

Silenced* Display>

message from the display, press the

soft key.

Alarm

Clear

The display will show the instructions for clearing the message. Enter a valid passcode and press the

Clear>

soft key.

If a fire trouble still exists after acknowledging the alarm, the display shows

Fire Trouble

To remove this display, the fire point(s) must be returned to normal. If you wish to review cleared events, use COMMAND 40.

Bosch Security Systems | 9/04 | 50410D 11

Page 12

D1260/D1260B | Owner's Manual | Part I: Security system basics - Burglary Alarms

3 seconds

Burglary Alarms

Burglary alarms are the second priority. When a burglary point activates while your system is armed, your keypad emits a steady high-pitched burglary tone. The tone sounds for the time set by your security

Silencing Burglary Alarms

Entering a personal passcode with the proper authority level silences a burglary alarm and disarms the system if it was armed.

The system will now display

company. The keypad display shows the number of burglary

points activated, the point text then idle text.

and then the number of points in alarm and the custom text of all the points in alarm, in the order of occurrence.

If there is more than one point causing an alarm, the display will show each point for three seconds before showing the next one. When the last alarm is shown, the next display is idle text followed by the first alarm

Entering COMMAND 4 clears the scrolling point text from the display.

The *

Alarm Silenced*

alternate with idle text as a reminder that it is still possible to view the text of the points in alarm by using the View Memory function. See (Command 40) for more information.

*Alarm Silenced*

### Alarms

message will continue to

VIEW MEMORY ?

To clear the event memory and remove the *

Silenced*

message from the display, press the Clear

Alarm

Display> soft key.

The display will show the instructions for clearing the message. Enter a valid passcode and press the Clear> soft key.

12 Bosch Security Systems | 9/04 | 50410D

Page 13

D1260/D1260B | Owner's Manual | Part I: Security system basics - Fire Trouble and Fire Supervisory Events

Fire Trouble and Fire Supervisory Events

When a fire trouble or fire supervisory condition occurs, your keypad emits three warble tones, then a pause (repeatedly).

The system displays the number of fire points that are in a trouble or supervisory condition as well as the point text of the affected points.

Silencing Fire Trouble and Fire Supervisory conditions

Pressing COMMAND 4 or the

Silence>

silences the conditions. In addition to this, entering a personal passcode with the proper authority level silences the condition and disarms the panel if it was armed. If you wish to review these cleared troubles, using COMMAND 40 can do this.

Some systems may be programmed to automatically re-sound the keypad’s trouble tone after a period of time if the fire trouble or fire supervisory condition remains. Consult your security company for further information.

Special Fire Trouble and Fire Supervisory Display

If you silence the keypad or clear a trouble or supervisory condition for a Fire Point from the display and the fire point remains in trouble,

Fire Supervisory

appears in the keypad’s display. This remains in the display until the condition causing the trouble is cleared.

Some fire points, when tripped, will display FIRE TROUBLE for a preset amount of time. If no other fire activity is detected, this condition will automatically clear. If the condition remains or another fire detector is tripped, a fire alarm will occur.

Viewing Fire Trouble and Fire Supervisory conditions

After pressing COMMAND 4 or entering your passcode, the text of the fire point in trouble continues to automatically scroll through the display. Press

Points>

soft key and then

Next>

soft key to scroll

these displays manually if you wish. Events scroll in chronological order.

soft key

Fire Trouble

View

Non-Fire Trouble and Supervisory Events

When a trouble event occurs, your keypad may be programmed to emit three warble tones, then a pause (repeatedly).

If the system was armed the keypad display shows the number of non-fire trouble events or non-fire supervisory events and then custom text for each activated point.

Silencing Non-Fire Trouble and Supervisory Events

Pressing COMMAND 4 or the

Silence>

soft key silences the Trouble and/or non-fire Supervisory conditions. In addition to this, entering a personal passcode with the proper authority level silences a trouble and disarms the panel if it was armed. Press the

View Points>

soft key then the

Next>

soft key to scroll these displays manually. If you wish to review these cleared troubles, use COMMAND 40 to do this.

Special System Trouble Display

These displays appear on all keypads in the system. See Standard Displays for a description of each system trouble display. Entering your passcode, COMMAND 4 or pressing the system trouble tone, but the System Trouble display will not clear until the faulted condition is corrected.

A system trouble display begins by sounding a trouble tone and then three seconds later the specific System Trouble Display is shown, such as

Cleared Events Are Not Lost

If you clear the alarms and troubles from the display, you can still view all the events that occurred since the last time the system was armed by using COMMAND 40 (View Event Memory).

Silence>

soft key will silence a

Service AC Fail

Some system may be programmed to not initiate a trouble tone during these conditions.

Bosch Security Systems | 9/04 | 50410D 13

Page 14

D1260/D1260B | Owner's Manual | Part I: Security system basics - Silencing an Alarm

Entry Delay Tone and Display

When you enter an armed system through a point programmed for entry delay, the keypad emits a repeating warble tone and displays the following to remind you to turn off your security system.

To SILENCE an alarm:

Enter your passcode and press ENTER.

If you fail to turn off the security system before the entry delay time expires, it may sound the burglary tone and may also send an alarm report to your security company.

Exit Delay Tone and Display

After you arm your system, the keypad emits a repeating beep tone, displays

is now arming…

then

AREA 1 NAME TEXT

EXIT NOW!

and counts down the exit delay time.

Keystroke Checking Tones Valid Entry

If you press an appropriate key for the function or entry you desire, the keypad emits a muted beep tone, indicating it accepted your keystroke.

Invalid Entry

A flat buzz tone sounds when you perform a function that is not allowed or when the keypad has no information to display.

How Your System Reports Alarms

Your security system may be programmed to automatically disconnect your telephones when sending reports to your security company. Once the report is completed, your security system returns the telephones to normal operation (check with your security company). Other methods of communicating alarm conditions are also available. Please consult your security company for services available in your area.

Your system makes repeated attempts to send reports to your security company.

In the event your security system fails to communicate, the keypad sounds a Trouble Tone and displays

1 WAREHOUSE Comm Fail Route Grp1

AREA

(where the

Route Group can be 1, 2, 3, or 4):

Notify your security company of the communications failure.

If your system uses telephone lines as its means of communication and telephone service is interrupted, your security system cannot send reports to your security company unless it has an alternate means of transmitting them.

Silencing an Alarm

The audible alarm sounds for a specific period of time before it automatically shuts off. If an alarm occurs and you want to silence the siren before the time expires, simply enter your personal passcode and press ENTER.

14 Bosch Security Systems | 9/04 | 50410D

Page 15

D1260/D1260B | Owner's Manual | Part II: System Commands - Entering a Passcode

Part II: System Commands

Below is a summary of the commands covered in this section.

Some of these functions may not be available in your system. Please consult your security company to determine which commands have been made available to you.

If you attempt to enter a function that’s not available or if the function is available in the system but your passcode is not authorized to perform the function, then

**No Authority**

will display on the Keypad.

Press the COMMAND key and then the one or two digits shown in the table below to perform the function. When you use a command to perform a function, the displays in the function list below do not appear at your keypad.

Some commands listed below may not be available. Contact your security company for more information.

Table 2: Keypad Commands

COMMAND Function

Master Arm

Master Arm Instant

Perimeter Instant

Perimeter Delay

Silence Trouble Sounder & Clear Trouble Display

View Memory

Walk Test

Reset Sensors

Watch Mode

Special Alert

Perimeter Partial

Special Alert

Walk Test

Entering a Passcode

1. The display may prompt you to enter your

passcode.

2. The passcode is shown as asterisks (*) when

entered and advance from the right side of the display to the left until all passcode digits (from a minimum of 3 to a maximum of six) are entered.

3. Press ENTER.

Bosch Security Systems | 9/04 | 50410D 15

Page 16

D1260/D1260B | Owner's Manual | Part II: System Commands - Turning On the System (Arming)

Turning On the System (Arming)

Your security system can be turned on (armed) in many different ways, depending on the arming command used. Arming Commands are those commands used to turn on the system. The most basic arming command is to arm the entire system. The simplest way to arm your system is to enter your personal passcode or press [COMMAND] [1].

There are several other arming commands to turn on the system. These are described later in this manual.

To Turn Your Security System On (Arm):

1. Enter your passcode and press ENTER.

2. The keypad briefly displays

TEXT is now arming…

AREA 1 NAME

Turning Off the System (Disarming)

Entering your personal passcode turns off your security system. When the system is turned on, you must enter through a designated entry door to prevent an instant alarm condition. Opening the door starts entry delay time and the Keypad emits a pulsing “beep” tone to remind you to turn off the system. Enter your passcode before the delay time expires and the system will turn off.

If you enter through the wrong door or fail to disarm before the entry delay time expires, you will cause an alarm.

If this happens, silence the alarm (by entering your personal passcode and pressing ENTER) and call your security company to let them know that it is not an emergency situation.

To Turn Your Security System Off (Disarm):

1. Enter your passcode and press ENTER.

and the exit delay tone begins. After exit delay time expires,

the display changes to idle armed text.

5. You must press the ENTER key within 5 seconds

of entering your passcode, or the passcode entry will be invalid.

6. The display returns to idle disarmed text.

Turning On the System (Arming) With a

Your passcode may have a special duress feature that is simply your personal passcode with its last digit increased by 1 or 2.

If an intruder demands that you arm or disarm the security system, you can use your duress passcode. The duress passcode arms or disarms the system an alarm report to your security company. There is no alarm tone or visual indication at the premises that the report is sent. Check with your security company before attempting to use this feature.

Duress Passcode

and

sends

16 Bosch Security Systems | 9/04 | 50410D

Page 17

D1260/D1260B | Owner's Manual | Part II: System Commands - Turning On the System (Arming) With Doors or

Turning On the System (Arming) With

Doors or Windows Open

If a protected door or window is open, you may have the option of “force arming” with that point faulted. Faulted points (opened doors or windows) that are force armed are not included in the system. The remaining points arm normally.

Force armed points either return to normal operation after you turn off your system or return to normal when the door or window is closed. Your system might not offer force arming or it may be restricted to specific points. Contact your security company for more information.

1. Use your passcode or an arming function to start

the arming process.

7. The display shows

8. One of the messages below may display in place of

Check Area #

Indicates that more than the number of allowable points are faulted. Bypassed points are counted as faulted. Your system’s maximum number of bypassed and/or force armed points is set by your security company. Check with them to learn this number.

9. The display shows

Ready to Arm

10. Pressing the

specifics for any points that are faulted, if any, and bypassed, if any.

Faulted points are displayed first then bypassed points.

11. The display changes to show the number of faulted

points in the area.

AREA 1 WAREHOUSE Not

View Points>

soft key will show the

Indicates the system is programmed not to arm with particular points faulted (doors or windows open).

Indicates that the system’s number of allowable bypassed points has been reached. Your system’s maximum number of bypassed and/or force armed points is set by your security company. Check with them to learn this number.

Press Next> soft key repeatedly to scroll through the point text for each faulted point.

If you do not want to go through the list of faulted points and want to go directly to the soft key or

COMMAND button.

Force Bypass>

soft key, press the

Force Arm>

Bosch Security Systems | 9/04 | 50410D 17

Page 18

D1260/D1260B | Owner's Manual | Part II: System Commands - Turning On the System (Arming) With Doors or

12. Once the last faulted point is displayed, pressing

the

Next>

soft key will start displaying a summary

and then specifics of any bypassed points.

13. Once the last bypassed point is displayed, the

display will change to show the soft key to either force arm the faulted points (

Force Arm>

) or force arm the faulted/bypassed points (

Force/Bypass Arm>

14. Press the appropriate soft key to arm your system

with the faulted/bypassed points removed from service.

18 Bosch Security Systems | 9/04 | 50410D

Page 19

D1260/D1260B | Owner's Manual | Part II: System Commands - MASTER ARM ? (COMMAND + 1)

MASTER ARM ? (COMMAND + 1)

Description

Use this function to turn on the entire system, both perimeter and interior. When you turn on the system, the display shows how many seconds of exit delay time you have to exit the protected area. You should leave before exit delay time expires.

Leaving after exit delay has expired will cause the entry delay to start. You may also cause an alarm on an interior device. Enter your personal passcode to disarm the system.

This function may be used by your cleaning service, a serviceman, or others who need to turn on your system when they leave.

Using Master Arm:

Using the COMMAND +1 shortcut will only arm the area where the keypad has been assigned. Example, if the D1260 is assigned to Area 1, only Area 1 will be

1. The display shows disarmed idle text.

armed when COMMAND + 1 is pressed.

6. If the passcode has valid authority for this

command, the display shows delay time remaining)

Exit now #

(# = exit

seconds remaining

After the exit delay time expires, the display changes to idle armed text.

7. To disarm your security system, enter your

personal passcode and press ENTER.

2. Press the COMMAND key.

3. The display shows

*System Command*

4. Press the 1 key

5. If your system is programmed to require a

passcode when performing a COMMAND 1, the display prompts you to enter your passcode.

The passcode is shown as asterisks (*).

Bosch Security Systems | 9/04 | 50410D 19

Page 20

D1260/D1260B | Owner's Manual | Part II: System Commands - MASTER ARM ? (COMMAND + 1)

Master Arming all Areas

If you prefer, you may use the Master Arm ?> command in the Command Menu to initiate this

7. To arm a selected area, press Next> until the

desired area appears (Area name text along with Arm Area # ?).

function which will arm all available areas according to your authority level.

1. The display shows disarmed idle text.

8. Then press Arm>

9. The next available area will appear with the option

to arm it.

2. Press the MENU> soft key to enter the Command

Menu,

Every time the keys are pressed, the display scrolls to the next unarmed area.

Next>,<Previous

3. then press NEXT> soft key repeatedly

Arm>

soft

4. until you reach the

MASTER ARM ?>

prompt.

Press the soft key.

5. The display may prompt you to enter your

passcode. The passcode is shown as asterisks (*) when

entered.

6. If there is more than one area that is set up, the

option is given to arm all of them with MASTER ARM ALL ?

or by pressing the Next> soft key…

10. To arm all available areas, press the Arm> soft

key when the display reads Master Arm All ?

11. The display changes to show that all areas are

arming. Depending on what areas are armed or areas that

you have authority, 12345678 may or may not appear.

12. then displays

Exit now #

(# = exit delay time

remaining).

to view each unarmed area and optionally arm each one.

After the exit delay time expires, the display changes to idle armed text.

20 Bosch Security Systems | 9/04 | 50410D

Page 21

D1260/D1260B | Owner's Manual | Part II: System Commands - MASTER ARM INST ? (COMMAND + 1 + 1)

13. To disarm your security system, enter your

personal passcode and press ENTER.

14. The display changes to show that all the areas are

disarmed. Depending on what areas are armed or areas that

you have authority, 12345678 may or may not appear.

MASTER ARM INST ? (COMMAND + 1 + 1)

Use this function to turn on a single area, both perimeter and interior without delays. When entering COMMAND 11, remember that the second 1 must be pressed within 2 seconds after pressing the first 1.

The menu entry that it allows all or selected areas to be armed instantly.

MASTER ARM INST>

is different in

COMMAND 11 does not comply with SIA CP-01 Standard.

The display returns to idle text.

Using the COMMAND + 1 + 1 shortcut will only instantly arm the area where the keypad has been assigned. Example, if the D1260 is assigned to Area 1, only Area 1 will be armed when COMMAND + 1 + 1 is pressed.

1. The display shows disarmed idle text.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 1 key. Now press the 1 key again.

4. The keypad display shows

WAREHOUSE All On Instant

AREA 1

5. To disarm your security system, enter your

personal passcode and press ENTER.

Bosch Security Systems | 9/04 | 50410D 21

Page 22

D1260/D1260B | Owner's Manual | Part II: System Commands - PERIMETR INST (COMMAND + 2)

PERIMETR INST (COMMAND + 2)

4. The display shows

Perimeter On Instant

Turn On the Perimeter With No Delays Description

Use this function to turn on only the perimeter of your building, leaving the interior of the building disarmed. This function allows no exit or entry delay time through the perimeter, including the designated exit delay door.

This function is useful in residential systems when everyone is home and ready to retire for the evening. You can have the security of an armed perimeter, yet move freely throughout the interior of the premises.

It is also useful in commercial systems when you are working before or after business hours and wish to have the perimeter armed. Remember there are no entry or exit delays when you use this function. You

After arming the perimeter without delays, you cannot enter or exit the premises without disarming the system. Opening a perimeter door before disarming will generate an alarm. If this happens, silence the alarm by turning off your system and call your security company to let them know that it is not an emergency situation.

5. To disarm your security system, enter your

personal passcode and press ENTER. The display then returns to idle text.

must disarm (turn off) the system to enter or exit the premises.

Using Perimeter Inst:

1. Interior points are not armed with this command

and may remain faulted while arming with COMMAND 2.

2. Press the COMMAND key.

The display shows

*System Command*

3. Press the 2 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu,

then press NEXT> soft key repeatedly.

until you reach the PERIMETR INST ?> prompt, then press the adjacent soft key.

22 Bosch Security Systems | 9/04 | 50410D

Page 23

D1260/D1260B | Owner's Manual | Part II: System Commands - PERIMETR DELAY ? (COMMAND + 3)

PERIMETR DELAY ? (COMMAND + 3)

Turn On the Perimeter With Delays Description

In residential systems this function allows you to only arm the perimeter and exit through a door programmed for exit delay. The interior of the building remains disarmed. People or pets are free to move throughout the interior of the premises.

This function is also useful in commercial systems when you are working before or after business hours and wish to have the perimeter armed. Other system users can enter through doors programmed for entry delay, which will start the entry delay sounder and countdown.

Using Perimeter Delay

1. Interior points are not armed with this command

and may remain faulted while arming with COMMAND 3.

2. Press the COMMAND key.

The display shows

*System Command*

After the exit delay expires,

Delayed

is displayed.

Perimeter On

5. To disarm your security system, enter your

personal passcode and press ENTER.

The display then returns to idle text.

3. Press the 3 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu,

then press NEXT> soft key repeatedly.

until you reach the PERIMETR DELAY ?> prompt, then press the adjacent soft key.

4. The display shows

time remaining).

Exit now! #

(# = exit delay

Bosch Security Systems | 9/04 | 50410D 23

Page 24

D1260/D1260B | Owner's Manual | Part II: System Commands - Silence the Trouble Sounder & Clear Trouble Display

Silence the Trouble Sounder & Clear

Trouble Display (COMMAND + 4)

Description

Use COMMAND 4 to silence the trouble sounder during system events. This command also clears system messages from the display. If an alarm has occurred and was silenced, the * will continue to scroll to remind you that cleared events can be seen with the View Memory function (refer to VIEW MEMORY ? (COMMAND + 4 + 0) on page 24).

Using COMMAND 4:

1. The display shows disarmed idle text.

ALARM SILENCED*

display

VIEW MEMORY ? (COMMAND + 4 + 0)

View Event Memory Description

Your system stores events that occurred since the last time memory was cleared. Use COMMAND 40 to view Event Memory.

Event Memory allows you or a service technician to review events after they are cleared from the keypad’s display. * to remind you that events are stored in Event Memory.

Each time you turn on the system on, the Event Memory is erased and the message is cleared.

ALARM SILENCED*

ALARM SILENCED

will continue to scroll

Using View Memory:

1. The display shows disarmed idle text.

Press the COMMAND key. The display shows

*System Command*

2. Press the COMMAND key. The display shows

*System Command*

2. Press the 4 key.

3. The Keypad sounder is silenced.

3. Press the 4 key and then the 0 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the VIEW MEMORY ?> prompt, press its adjacent soft key.

Press ENTER.

24 Bosch Security Systems | 9/04 | 50410D

Page 25

D1260/D1260B | Owner's Manual | Part II: System Commands - WALK TEST ? (COMMAND + 4 + 4)

4. Your system displays event summary lines and

point text in this order: a. fire alarm summary line

b. point text for each fire alarm event c. alarm summary line d. point text for each alarm event e. fire trouble summary line f. point text for each fire trouble event g. trouble summary line h. point text for each trouble event.

5. Press NEXT> to scroll through the events.

If there are no events to view,

currently no events in memory

There are

displays.

Upon initiation, the walk test will test the burglary bell pattern on the bell output and ring the keypad burglary bell for 2 seconds. The AC will be disabled for 4 minutes in order to test the system’s battery power. If the battery cannot maintain the system for the 4-minute period, the keypad will appear to go dead. If your keypads are programmed to be supervised, the main alarm panel will beep intermittently during this 4minute period. If this happens, contact your security company. At the end of the 4-minute period, AC is returned to the system and the panel restores. To test individual detection devices, simply activate sensors and open protected doors and windows one-at-a-time. As each detection device is faulted, the Keypad emits a brief tone and the display indicates for 60 seconds that the point has been tested. This verifies that each detection device is working properly.

Using Walk Test:

1. The display shows disarmed idle text.

6. You can return to idle text at any time by pressing

Exit> soft key.

WALK TEST ? (COMMAND + 4 + 4)

Walk Test Description

Use this function to test keypads, detection devices, and sounders (both interior and exterior) to be certain they function properly. You can review untested points at your keypad to help pinpoint any problems.

You cannot arm your system while in the walk test mode, and no alarm reports are sent to your security company unless a 24-hour point is activated (such as fire or panic). A Walk Test Start Report may be programmed to be sent to your security company.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 4 key and then the 4 key.

Bosch Security Systems | 9/04 | 50410D 25

Page 26

D1260/D1260B | Owner's Manual | Part II: System Commands - WALK TEST ? (COMMAND + 4 + 4)

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate

The display shows

### points untested

this function. Press the MENU> soft key to enter the

Command Menu.

Press NEXT> soft key repeatedly.

information about specific points that have not yet been tested.

Press the

Next Pt>

Prev Pt>

soft keys to see

6. Move through this list by pressing the

soft key.

When you reach the WALK TEST ?> prompt, press its adjacent soft key.

Next Pt>

Press ENTER.

4. The burglary bell sounds for 2 seconds. When the

display shows

### points remain to be tested

(### is the number of points) you can begin.

If you know the point number, you can enter it by pressing its number key and then the ENTER key

The display will change to show the point that was entered. If the point is invalid the message “Invalid Point” or “This is not a valid walk point” appears.

Test each point by first opening and then closing the door or window or other detection device.

Check the display after testing each point. For interior points, walking past the device once is sufficient. If any point does not test correctly, contact your security company for service.

5. During the Walk Test you may want to see the

points that remain untested by pressing the

untested pts>

soft key.

View

The display changes to show the information for that point.

Press the

Exit>

soft key to return to the

points remain to be tested

continuing with the walk test.

7. When all points have been tested,

remain to be tested

Press the

<Exit

is displayed.

soft key.

The display momentarily shows

been tested.

The displays then shows idle text.

###

screen before

0 points

All points have

26 Bosch Security Systems | 9/04 | 50410D

Page 27

D1260/D1260B | Owner's Manual | Part II: System Commands - RESET SENSORS ? (COMMAND + 4 + 7)

RESET SENSORS ? (COMMAND + 4 + 7)

Reset Sensors Description

Detection devices, such as smoke detectors and shock sensors, must be reset after being activated. This function momentarily removes power from these sensors to reset them.

It also clears point information from the display, leaving the *ALARM SILENCED display as a reminder that the View Memory function can be used to view the cleared point information.

To clear the event memory and remove the *

Silenced*

message from the display, press the Clear

Display> soft key.

The display will show the instructions for clearing the message. Enter a valid passcode and press the Clear> soft key.

message in the

Alarm

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the RESET SENSORS ?> prompt, press its adjacent soft key.

Press ENTER.

4. The display shows for approximately 15 to 20

seconds.

Arming the system will also clear the display and the event memory.

Using Reset Sensors:

1. The display shows disarmed idle text.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 4 key, followed by the 7 key.

The display then shows retrieving the panel information.

The display then returns to show idle text.

If you enter this function and the detector or sensor resets momentarily, but then returns to a faulted condition, the conditions causing the activation may still be present or the detector may be faulty. Check to be certain that there is no smoke, fire, or other danger present. If you can’t reset the detector or sensor contact your security company.

Bosch Security Systems | 9/04 | 50410D 27

Page 28

D1260/D1260B | Owner's Manual | Part II: System Commands - WATCH MODE ? (COMMAND + 6)

WATCH MODE ? (COMMAND + 6)

Watch Mode

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Description

With your security system disarmed, you can use watch mode to monitor some points. Each time some points

Press the MENU> soft key to enter the Command Menu.

are faulted (door or window is opened) the keypad chimes once and displays the point text for 60 seconds. No alarms are generated by this mode except 24-hour

Press NEXT> soft key repeatedly.

alarms (fire, panic, etc.). When the keypad’s keypad lighting is on, the keypad

does not chime. The keys light for 20 seconds whenever you press a key.

Use this function in residential systems to monitor

When you reach the WATCH MODE ?> prompt, press its adjacent soft key.

entries or exits in your home. In commercial systems it can serve as a door chime to alert you when a customer or delivery person enters your business.

Press ENTER.

Contact your security company to find out which points are watch points and whether or not your system automatically turns the Watch Mode on whenever you disarm.

3. The display briefly shows

on.

Watch Mode is now

Entering Watch Mode:

1. The display shows disarmed idle text.

Press the COMMAND key. The display shows

*System Command*

2. Press the 6 key.

The display returns to show idle text.

Exiting Watch Mode:

1. The display shows disarmed idle text.

Press the COMMAND key. The display shows

*System Command*

2. Press the 6 key.

28 Bosch Security Systems | 9/04 | 50410D

Page 29

D1260/D1260B | Owner's Manual | Part II: System Commands - PERIMETR PART ? (COMMAND + 8)

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

In commercial systems, when you need access to the large overhead doors to receive deliveries, using this function will allow you to keep the rest of the building perimeter armed.

Press the MENU> soft key to enter the Command Menu.

Using Perimetr Part:

1. The display shows disarmed idle text.

Press NEXT> soft key repeatedly.

When you reach the WATCH MODE ?> prompt, press its adjacent soft key.

Press ENTER.

3. The display briefly shows

off.

Watch Mode is now

The display returns to show idle text.

PERIMETR PART ? (COMMAND + 8)

Partially Turn On the Perimeter Description

This function is used to turn on the perimeter of your building while selected portions of the perimeter remain turned off. Perimeter points that are not secure (faulted) when this function is entered are automatically bypassed and are not included in the system. This function does not turn on the interior of your building. Entry/exit delays are provided with this arming command.

Use this function in residential systems to turn on the front of your house while the interior and the rear perimeter doors are left turned off, giving you freedom of movement between the house and patio.

Press the COMMAND key. The display shows

*System Command*

2. Press the 8 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the PERIMETR PART ?> prompt, press its adjacent soft key.

Press ENTER.

3. The display prompts the user to exit the area and

starts counting down from 10 seconds to arm the system.

# is the number of seconds remaining, counting down from 10 seconds, before the system is armed.

Bosch Security Systems | 9/04 | 50410D 29

Page 30

D1260/D1260B | Owner's Manual | Part II: System Commands - Special Alerts (COMMAND + 7 and COMMAND +

4. When exit delay time expires and the system turns

on, the display shows:

Special Alerts (COMMAND + 7 and

COMMAND + 9)

Description

Commands 7 and 9 can be programmed to respond to a choice of numerous situations that may need immediate attention. They may also be used to send a

5. When performing a COMMAND 8 and no points

are faulted or if the points return to normal before

silent alarm to your security company without sounding an alarm signal on the premises. Check with your security company for the options they offer.

the exit delay time expires, the system is turned on as in COMMAND 3.

6. To disarm, enter your personal passcode and press

Using COMMAND 7:

1. The display shows disarmed idle text.

ENTER.

Press the COMMAND key. The display shows

*System Command*

2. Press the 7 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the USER CMD 7 ?> prompt, press its adjacent soft key.

Press ENTER.

30 Bosch Security Systems | 9/04 | 50410D

Page 31

D1260/D1260B | Owner's Manual | Part II: System Commands - Special Alerts (COMMAND + 7 and COMMAND

3. Your COMMAND 7 special alert has been

programmed to:

 notify your alarm company  ring a bell on your premises  display at your keypad

Description: __________________________________________

__________________________________________ __________________________________________

Using COMMAND 9:

3. Your COMMAND 9 special alert has been

programmed to:

 notify your alarm company  ring a bell on your premises  display at your keypad

Description: __________________________________________

__________________________________________ __________________________________________

1. The display shows disarmed idle text.

Press the COMMAND key. The display shows

*System Command*

2. Press the 9 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the USER CMD 9 ?> prompt, press its adjacent soft key.

Press ENTER.

Bosch Security Systems | 9/04 | 50410D 31

Page 32

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - Advanced Commands

Part III: Advanced Commands

Use this section of the manual to perform advanced system functions like add and delete user passcodes, reassign authority levels to user passcodes and operate or change programmed scheduled events (Skeds) from the keypads. As you make changes to the system, update the information contained in the tables in this guide to provide an accurate account of the programmed information.

Advanced Commands

Some commands listed below may not be available. Contact your security company for more information.

Advanced

COMMAND Function

Bypass a Point

Unbypass a Point

COMMAND Function

Advanced

Change Sked

Delete Passcode

Test Report

Status Report

Remote Program

Change Time/Date

Door Control

Access Level Change

Change Display

Move to Area

Extend Closing

Print Log View Log View Point Status

Change Relay

Change Passcode

Add Passcode

Default Text

Fire Test

Display Rev

Terms Used in This Section

Listed below are some of the terms you’ll see throughout this section. Each term is covered in greater detail later in this section and in Part II: System Commands.

Account Area Arm and Disarm

Authority Levels Keypad Keypad Scope Panel

Relays Skeds

One or more areas reporting under a particular account number. A group of detection devices connected to your security system. To switch your burglar detection devices “on” and “off.” When the burglar detection

device is armed and is tripped, an alarm may be set off. When the burglar detection devices are disarmed, the security system will not detect intruders. Detection devices programmed as 24-Hour or Fire points are always on.

Levels of access authority assigned to passcodes. Arming station used to operate your security system. Determines which areas a particular keypad can access. The main control unit, which is locked in a steel enclosure. It sends data to and

receives inputs from the keypads. Optional dry contact outputs that respond to system events. Functions programmed by your security company that occur at predetermined

32 Bosch Security Systems | 9/04 | 50410D

Page 33

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - BYPASS A POINT? (COMMAND + 0)

times.

User Passcodes

A three to six digit number entered at a keypad to access the system.

BYPASS A POINT? (COMMAND + 0)

Description

This command allows you to bypass points that you do not want included in the system. Points that are not included in the system do not detect intruders and cannot send any reports. You can bypass points when an area is disarmed. Bypassing a point reduces the level of security and should be used with discretion. Points remain bypassed until you unbypass them or some points may return when the area is disarmed. See Unbypassing a Point (COMMAND 00).

You could use COMMAND 0 to leave a window open over night without initiating an alarm. Also see Turning the System On With Doors or Windows Open.

Using Bypass a Point

1. The display shows disarmed idle text.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the BYPASS A POINT ?> prompt, press its adjacent soft key.

Press ENTER.

Press the COMMAND key. The display shows

*System Command*

2. Press the 0 key.

3. You will prompted for your passcode. It will

appear on the display as asterisks (*).

4. The display changes to show

or press next key

Enter point number

Bosch Security Systems | 9/04 | 50410D 33

Page 34

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - BYPASS A POINT? (COMMAND + 0)

•

5. If a digit is pressed, the display shows

number: #

display changes to

. As soon as a digit key is pressed, the

Entering point number:

Enter point

FRONT DOOR cannot by bypassed.

indicates the system is programmed not to allow that point to be bypassed.

(# is the point number entered) If you know the point number you wish to bypass,

enter the number and press the Enter> soft key or the ENTER button.

If you don’t know the number of the point you wish to bypass, you can view the list of devices that can be bypassed by pressing the Next> soft key.

Continuously pressing Next> scrolls through the available points that can be bypassed.

When the point text of the point you wish to bypass appears, press the Bypass> soft key.

One of the following messages displays (FRONT DOOR is used here as an example):

•

FRONT DOOR is not bypassed

point is not bypassed and the option is given to bypass it.

FRONT DOOR is now bypassed.

•

the point was successfully bypassed.

indicates the

indicates

Invalid point Please try again.

•

the entered point doesn’t exist and the display returns to allow another point to be entered.

No additional points.

•

no more points that can be bypassed.

6. You can return to idle text by pressing <Exit.

7. If the bypassed point is a 24-hour point, the

message in the display with

24Hr Point Bypassed

A1 AREA IS OFF

indicates that there are

indicates that

begins alternating

FRONT DOOR is already bypassed.

•

indicates that the point has already been bypassed.

34 Bosch Security Systems | 9/04 | 50410D

If the bypassed point is a Fire Point, the message

Fire Point Bypassed

display with

A1 AREA IS OFF

begins alternating in the

Page 35

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - UNBYPASS A POINT? (COMMAND + 0 + 0)

UNBYPASS A POINT? (COMMAND + 0 + 0)

Description

4. The display changes to show

or press next key

Enter point number

Unbypassing a point is a way to return a bypassed point to the security system so that it can once again respond to trouble and alarm conditions.

Using Unbypass a Point:

1. The display shows disarmed idle text.

5. If digits are pressed, the display shows

number: #.

display changes to

As soon as a digit key is pressed, the

Entering point number:

Enter point

Press the COMMAND key. The display shows

*System Command*

(# is the point number that was entered) If you know the point number you wish to

unbypass, enter the number and press the

Enter>

soft key or the ENTER button.

2. Press the 0 key twice.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

If you don’t know the number of the point you wish to unbypass, you can view the list of devices that can be unbypassed by pressing the

Next>

key. Continuously pressing

Next>

scrolls through the

available points that are currently bypassed. When the point text of the point you wish to

unbypass appears, press the

Unbypass>

soft key.

soft

Press NEXT> soft key repeatedly.

When you reach the UNBYPAS A POINT ?> prompt, press its adjacent soft key.

Press ENTER.

3. You will prompted for your passcode. It will

appear on the display as asterisks (*).

One of the following messages displays (FRONT DOOR is used here as an example):

•

FRONT DOOR is not bypassed

point is not bypassed and the option is given

indicates the

to bypass it.

FRONT DOOR is now bypassed.

•

indicates

the point was successfully bypassed.

Bosch Security Systems | 9/04 | 50410D 35

Page 36

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SEND REPORT ? (COMMAND + 4+1 or 4+2)

•

FRONT DOOR is already bypassed.

indicates that the point has already been bypassed.

SEND REPORT ? (COMMAND + 4+1 or

4+2)

Description

This function tests the communication link between your security system and your security company. It is an important part of maintaining a high level of security for your property.

Two types of test reports may be sent. The first type of report is a simple test report (Command 41). The second type of report is a status report (Command 42).

FRONT DOOR cannot by bypassed.

•

indicates the system is programmed not to allow that point to be bypassed.

This status report indicates the current condition of your system.

Using Send Report

1. Always call your security company before sending

Invalid point Please try again.

•

indicates that

the entered point doesn’t exist and the display

a test report.

2. The display shows disarmed idle text.

returns to allow another point to be entered.

No additional points.

•

indicates that there are

no more points that can be bypassed.

6. You can return to idle text by pressing <Exit.

7. If you are attempting to unbypass a 24-Hour or

Fire Point that is still faulted, the keypad will display

Cannot unbypass 24hr faulted points.

Press the COMMAND key. The display shows

*System Command*

3. Press the 4 key then the 1 key to send a test report.

Press the 4 key then the 2 key to send a status report.

36 Bosch Security Systems | 9/04 | 50410D

Page 37

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SEND REPORT ? (COMMAND + 4+1 or 4+2)

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

6. If the test (or status) report doesn‘t successfully

transmit to the central station, the keypad may sound a trouble tone and display

Route Grp#

(# = 1-4) after numerous unsuccessful

Comm Fail

attempts.

Press NEXT> soft key repeatedly.

When you reach the SEND REPORT ?> prompt, press its adjacent soft key.

Another menu appears allowing for the selection of sending a test report (Test Rpt?>) or a status report (Status Rpt?>). Press either one of the adjacent soft keys.

4. The keypad displays

wait…

until the report is transmitted to the

Sending report… Please

security company.

5. When the transmission is complete the keypad

displays

Report sent

for 5 seconds.

If the <Exit soft key is pressed before 5 seconds have elapsed, idle text will be displayed.

The display returns to idle text.

Bosch Security Systems | 9/04 | 50410D 37

Page 38

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - REMOTE PROGRAM ? (COMMAND + 4 + 3)

REMOTE PROGRAM ? (COMMAND + 4 + 3)

Description

This function allows the user to initiate Remote Account Manager sessions. When the phone is ringing at the panel, the user initiates this function to have the

5. Press the 4 key then the 3 key.

6. Do not hang up the telephone.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

panel seize the line. Your security company can remotely program your

security system using the telephone line to which your

Press the MENU> soft key to enter the Command Menu.

panel is connected. Typical remote programming functions include: changing personal passcodes, changing entry/exit delays, resetting the system

Press NEXT> soft key repeatedly.

clock/calendar, and adding/deleting system arming commands.

Your security company may ask you to follow the steps below to begin a remote programming session. The time it takes to program the panel is dependent on the number of changes made to the program.

When you reach the REMOTE PROGRAM ?> prompt, press its adjacent soft key.

You’ll notice that two sets of procedures are presented. The one you use will depend upon whether your system has a pre-programmed telephone number

Press ENTER.

in its memory.

 My system has a phone number  My system does not have a phone number

For systems without a phone number

1. The display shows disarmed idle text.

7. The display changes to show the two choices that

are available for connecting to RAM:

• Contact RAM: RAM via phone or network

• Answer Now

2. Call this phone number:

___________________________

This number is designated for the Remote Account Manager.

You must make the call using the telephone located at:

___________________________

3. Identify yourself and your premises (account

number, name, address, etc.) and advise the

8. Press the

RAM.

Answer Now>

When your security company is communicating with your panel during a RAM session, the D1260 may display Call for Service…

9. The display shows

soft key to connect to

RAM connecting

…

operator of the services you wish to have performed. When the operator instructs you, proceed to steps 4 and 5.

4. Press the COMMAND key. The display shows

*System Command*

10. The security system will now disconnect

telephones sharing its telephone line during the remote programming session. Hang up the telephone now.

38 Bosch Security Systems | 9/04 | 50410D

Page 39

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - REMOTE PROGRAM ? (COMMAND + 4 + 3)

11. At the conclusion of the programming session your

system sends a report to the security company and then returns your telephone to normal service and your display to idle text.

15. The display changes to show the two choices that

are available for connecting to RAM:

• Contact RAM: RAM via phone or network

• Answer Now

For systems with a phone number or network connection

 My system uses a phone number for Remote

Programming

 My system uses an IP Address and network

connection for Remote Programming

12. Ensure your keypad shows idle disarmed text.

13. Press the COMMAND key. The display shows

*System Command*

14. Press the 4 key then the 3 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

16. Press the

Contact RAM>

soft key to specify the

connection method to RAM.

17. Press either the

RAM via phone>

(to connect the panel to the RAM software via a pre-programmed phone number) or

RAM via network>

soft key (to connect the panel to the RAM software via a pre-programmed IP network address).

18. The display shows

RAM connecting

…

19. The security system will now call the telephone

number or connect to the IP Address specified for network connection during the remote programming session.

20. At the conclusion of the programming session your

system sends a report to the security company and then returns your telephone to normal service and your display to idle text.

Press NEXT> soft key repeatedly.

When you reach the REMOTE PROGRAM ?> prompt, press its adjacent soft key.

Press ENTER.

Bosch Security Systems | 9/04 | 50410D 39

Page 40

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHANGE TIME/DATE (COMMAND + 4 + 5)

CHANGE TIME/DATE (COMMAND + 4 + 5)

4. The display changes to

Enter new time:

The time and date in your system must be correct for scheduled events to occur at the correct times. Check the time at least once a month to ensure accuracy. Use this function to set both the time and date. The system uses a 12-hour, AM/PM format. There is the option to continuously display the time and date in place of area status. The Time and Date will be shown continuously until a new command is entered or the current area’s status has changed. See CHANGE DISPLAY (COMMAND + 4 + 9), Time/Date Display for more information.

To just change the date, press the key, See Step 6.

If you input the wrong time, press the key to clear the time.

Enter the new time using a 12-hour (HH:MM)

Set Date>

<Exit

soft

format.

1. Ensure your keypad shows idle disarmed text.

Ex: If the desired time is 12:34, press 1 + 2 + 3 + 4

2. Press the COMMAND key. The display shows

*System Command*

The Set Date> soft key will disappear when the first digit is entered.

3. Press the 4 and then the 5 key.

Press the

5. The display changes to show

keys.

Enter>

soft key or the [ENTER] button.

AM>

PM>

soft

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press the Press the

6. The display shows

AM> PM>

soft key to select AM.

soft key to select PM.

Enter new date:

Press NEXT> soft key repeatedly.

When you reach the CHG TIME/DATE ?> prompt, press its adjacent soft key.

See Step 9 for use of the

Time/Date Display>

soft key. If you input the wrong date, press the

<Exit

soft

key to clear the time.

40 Bosch Security Systems | 9/04 | 50410D

Page 41

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DOOR CONTROL (COMMAND + 4 + 6)

Enter the new date using a MM/DD/YY format. Ex: If the desired time is January 1, 2002,

press 0 + 1 + 0 + 1 + 0 + 2

7. Press the

8. The

Enter>

soft key or the [ENTER] button.

Time/Date Display>

soft key is used to show

how the time and date entered will look.

DOOR CONTROL (COMMAND + 4 + 6)

Description

There are three functions with the door control function:

•

Cycle Door

allow a person into an area

Unlock Door

•

Secure Door

regardless of a user’s authority level

Using Door Control

1. Ensure your keypad shows idle disarmed text.

– momentarily unlocks a door to

– unlocks a door to allow free access

– locks a door and prohibits access

9. The new time and/or date is displayed for 20

seconds before the display returns to idle text.

Press the

<Exit

soft key to return to idle text.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the

key and the 6 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the DOOR CONTROL ?> prompt, press its adjacent soft key.

4. The display will change and show a choice of

Cycle Door>, Unlock Door> Door>

, and

Secure

Press the adjacent soft key.

Bosch Security Systems | 9/04 | 50410D 41

Page 42

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DOOR CONTROL (COMMAND + 4 + 6)

Cycle Door

1. If you wish to momentarily unlock an access door

to allow a person into an area, press the

Door>

2. The display will read *

soft key.

Cycle Door*1 2 3 4 5 6 7 8

Cycle

2. The display will read *

if all door are at a normal state and are available.

Unlock Door*1 2 3 4 5 6 7

if all door are at a normal state and are available.

If a door is not at a normal state, the number of the door would be replaced with a symbol indicated in Table 3.

3. Enter the number of the door you wish to unlock

then press the ENTER key. This door will be unlocked and the display will change to reflect the new status of the doors.

For example, if you wanted to unlock Door 3,

Table 3: Door Status

Symbol Meaning

- Door is not active, in scope, or user does not have access level authority.

C Door is on timed door sequence. U Strike and shunt are latched active (held

open).

X Strike and shunt are deactivated (secured). F There is a problem with the door. Call your

security company.

3. Enter the number of the door you wish to cycle

then press the ENTER key. This door will be cycled and the display will change to reflect the new status of the doors.

For example, if you wanted to cycle Door 3, press

then press the ENTER key.

press

then press the ENTER key.

The display changes to show that all the doors are at a normal state except for Door 3, which is unlocked.

4. Enter another door number to unlock or press the

Exit>

soft key to leave this function.

Secure Door

1. If you wish to unlock an access door to allow free

access, press the

2. The display will read *

if all door are at a normal state and are available.

Unlock Door>

Secure Door*1 2 3 4 5 6 7

soft key.

The display changes to show that all the doors are at a normal state except for Door 3, which is cycled.

If a door is not at a normal state, the number of the door would be replaced with a symbol indicated in

4. Enter another door number to cycle or press the

Exit>

soft key to leave this function.

Unlock Door

Table 3 on page 42.

3. Enter the number of the door you wish to secure

then press the ENTER key. This door will be secured and the display will change to reflect the new status of the doors.

1. If you wish to unlock an access door to allow free

access, press the

Unlock Door>

soft key.

42 Bosch Security Systems | 9/04 | 50410D

Page 43

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - Access Level

For example, if you wanted to secure Door 3, press

then press the ENTER key.

The display changes to show that all the doors are at a normal state except for Door 3, which is secured.

4. Enter another door number to secure or press the

Exit>

soft key to leave this function.

Access Level

This function is used to manually enable/disable access authority levels assigned to users. It can also be used to temporarily disable a user’s access level instead of deleting and then re-adding the user.

 I have this feature.  I do not have this feature.

1. Ensure your keypad shows idle disarmed text.

2. Press the

Menu.

3. Press

the

Menu>

Next>

soft key to enter the Command

soft key repeatedly until you reach

CHANGE LEVEL ?>

prompt.

Press the adjacent soft key.

4. A prompt will appear asking for entry of the

Authority Level to be modified.

5. Enter the level number (1 – 14) and press the

Enter>

soft key.

6. If the level entered is currently enabled, the

keypad will ask if you want to disable this level.

(Level 14 is used here as an example.)

7. If the level entered is currently disabled, the

keypad will ask if you want to enable this level.

(Level 14 is used here as an example.)

Bosch Security Systems | 9/04 | 50410D 43

Page 44

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHANGE DISPLAY (COMMAND + 4 + 9)

8. After selecting whether to disable or enable the

level, the display prompts you again to enter an Authority Level to modify.

CHANGE DISPLAY (COMMAND + 4 + 9)

This function presents three options:

• dim the display

• brighten the display

• continuously show the time and date in the display.

Brighten/Dim Display

You can change your keypad’s display to make the backlit LCD display bright or dim. When the display is dim, the tones are softer than when the display is bright. Use this option for keypads in bedrooms where

9. Press the

<Exit

soft key when you are finished.

a brighter display and louder tones could interfere with sleep.

If you dim the keypad backlit display and an alarm or trouble condition arises, the display automatically brightens and the volume increases. The backlit display returns to dim lighting when you clear the alarm or trouble condition.

Show Continuous Time/Date

Use this function to replace the disarmed idle text with a continuous time and date display and to prevent a passersby from knowing the status of your system.

Any time your keypad has an event to display, the time and date display is automatically removed. To return the time and date display, you must perform this function again.

1. Ensure your keypad shows idle disarmed text.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 4 and then the 9 key.

44 Bosch Security Systems | 9/04 | 50410D

Page 45

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - EXTEND CLOSING (COMMAND + 5 + 1)

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

EXTEND CLOSING (COMMAND + 5 + 1)

Your system may be programmed to expect you to arm within a scheduled closing window, which is a duration of time that is programmed by your alarm company. Your system may also be programmed to automatically arm at the end of the window.

COMMAND 51 lets you extend the scheduled closing

Press NEXT> soft key repeatedly.

window time either prior to the closing window time or during the closing window time. Use this function when you expect to stay past the scheduled end of the closing window. Your alarm company sets the length of

When you reach the CHG DISPLAY ?> prompt, press its adjacent soft key.

time prior to the start of the closing window in which you are allowed to extend the closing window.

Close window is not currently active

the time when the keypad won’t allow the window to be extended.

displays during

4. The display changes to show the display options:

Bright Display> -

•

Press to increase the LCD’s backlit brightness. The backlight adjustment will take effect after 20 seconds of inactivity.

•

Dim Display> -

Press to decrease the LCD’s

At the beginning of the closing window, the keypad beeps and displays

Please Close Now

to remind you to arm your system. It remains in the display until you arm, the close window ends, or you extend closing.

backlit brightness. The backlight adjustment will take effect after 20 seconds of inactivity.

•

Time/Date Display> -

Press to continuously

show the time and date instead of idle text.

The closing window can only be extended once the window has started.

If your system is turned on (armed), you cannot display the time.

Alarm or trouble messages replace this message in the event of an alarm or trouble condition.

To further adjust the LCD’s brightness, the settings for the Bright Display> and Dim Display> soft keys can be changed by accessing the Service Manual (99 + Enter).

Pressing the and clear the message for 10 minutes.

Silence>

soft key will silence the beep

If the alarm or trouble condition clears before the end of the close window

Please Close Now

message

returns to the keypad display.

Bosch Security Systems | 9/04 | 50410D 45

Page 46

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - EXTEND CLOSING (COMMAND + 5 + 1)

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

If you have not armed or extended closing, the

Close Now

message and beep will reappear after 10

Please

minutes. Your alarm company sets the length of time for the closing window. To extend the window, enter the new time at which you would like the reminder tone to begin. This time will be the new beginning of the closing window. The time length of the closing window is programmed by your security company and remains fixed.

When you hear the warning you can:

• Press the

Silence>

soft key will silence the beep

and clear the message for 10 minutes

• Leave before the end of the closing window

• Stay past the scheduled end of the closing window,

by using COMMAND 51 to extend the closing window.

Extending the closing window does not effect the amount of time available to close.

For example, if your closing window starts at 4:00 p.m. and stops at 4:30 p.m. and you extend closing to 5:00 p.m., the closing window will now be between 5:00 and 5:30 p.m.

1. Ensure your keypad shows idle disarmed text.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the EXTEND CLOSING ?> prompt, press its adjacent soft key.

4. The display changes to show the current start time.

Press the

Change>

soft key to change the start

time. Press the

Accept>

soft key to accept the start time

and return to idle text.

5. Enter the new time using a 12-hour (HH:MM)

format.

Ex:

If the desired time is 12:34, press [1] [2] [3] [4]

2. Press the COMMAND key. The display shows

*System Command*

Press the Press the

AM>

soft key to select AM.

PM>

soft key to select PM.

6. The display changes to show the new start time

briefly before returning to idle text.

3. Press the 5 key and then the 1 key.

7. Press the

Accept>

soft key to accept the Close

Start time.

46 Bosch Security Systems | 9/04 | 50410D

Page 47

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG SKEDS ? (COMMAND + 5 + 2)

CHG SKEDS ? (COMMAND + 5 + 2)

Description

A Sked is a function programmed to be performed automatically at a scheduled time by your security system. You can change the scheduled time for some functions, disable the Sked and thus prevent it from automatically happening or restart a previously disabled Sked. Contact your security representative to determine what Skeds may be programmed for your system.

To change a Sked’s time, enable a Sked, or disable a Sked, follow the procedure below to first select the Sked from a list of Skeds programmed for your system.

Using Chg SKEDS

1. Ensure your keypad shows idle disarmed text.

2. Press the COMMAND key. The display shows

*System Command*

4. The number of the first Sked programmed into

your system is displayed, plus either its time or an indication that it is disabled.

Press the

Next>

soft key to scroll through the list

of Sked numbers to find the one you wish to change.

Your alarm system may be programmed with up to 40 Skeds. If the Sked number being displayed is not programmed, the keypad will display

No program

. (11 is used as an example).

Skd11 –

When an

appears in the Sked display, it is an

indication that “Except on Holidays” is enabled.

3. Press the 5 key and then the 2 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the CHG SKEDS ?> prompt, press its adjacent soft key.

Specific holidays are programmed by your security company.

When an

appears in the Sked display, it is an

indication that the Sked has or will happen today.

5. If the Sked is currently enabled, the sked is shown

with

Disable this sked>

on the second line. Press

the adjacent soft key.

6. The display changes to show that the sked is

disabled.

If the Sked is currently disabled, the display says

Skd 1 is disabled.

Press the

7. The display shows two soft keys:

Enable this sked>

soft key.

Bosch Security Systems | 9/04 | 50410D 47

Page 48

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG SKEDS ? (COMMAND + 5 + 2)

•

Only on holiday>

Pressing this soft key will enable the sked only on holidays and change the first line of the display to

Except on holiday>

•

Pressing this soft key will disable the sked on holidays and change the first line of the display to

Consult your security company and determine which holidays have been programmed in your system.

The display changes to allow a new time to be entered.

Skd 1 X 08:00AM

Skd 1 08:00am

without the X.

with the X.

Enter the new time using a 12-hour (HH:MM) format.

Ex:

If the desired time is 8:00, press

Press the

8. If the time is a valid time, the keypad display

changes to show the new time with a selection of AM or PM.

Press the Press the

9. The display shows the Sked with the new time.

Enter>

AM> PM>

soft key or the ENTER button.

soft key to select AM.

soft key to select PM.

8 + 0 + 0.

Press the

48 Bosch Security Systems | 9/04 | 50410D

<Exit

soft key to return to idle text.

Page 49

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG SKEDS ? (COMMAND + 5 + 2)

Table 4: Sked Table

SKED # Except on

Holiday

SKED 1 Yes / No S M T W T F S SKED 2 Yes / No S M T W T F S SKED 3 Yes / No S M T W T F S SKED 4 Yes / No S M T W T F S SKED 5 Yes / No S M T W T F S SKED 6 Yes / No S M T W T F S SKED 7 Yes / No S M T W T F S SKED 8 Yes / No S M T W T F S SKED 9 Yes / No S M T W T F S SKED 10 Yes / No S M T W T F S SKED 11 Yes / No S M T W T F S SKED 12 Yes / No S M T W T F S SKED 13 Yes / No S M T W T F S SKED 14 Yes / No S M T W T F S SKED 15 Yes / No S M T W T F S SKED 16 Yes / No S M T W T F S SKED 17 Yes / No S M T W T F S SKED 18 Yes / No S M T W T F S SKED 19 Yes / No S M T W T F S SKED 20 Yes / No S M T W T F S SKED 21 Yes / No S M T W T F S SKED 22 Yes / No S M T W T F S SKED 23 Yes / No S M T W T F S SKED 24 Yes / No S M T W T F S SKED 25 Yes / No S M T W T F S SKED 26 Yes / No S M T W T F S SKED 27 Yes / No S M T W T F S SKED 28 Yes / No S M T W T F S SKED 29 Yes / No S M T W T F S SKED 30 Yes / No S M T W T F S SKED 31 Yes / No S M T W T F S SKED 32 Yes / No S M T W T F S SKED 33 Yes / No S M T W T F S SKED 34 Yes / No S M T W T F S SKED 35 Yes / No S M T W T F S SKED 36 Yes / No S M T W T F S SKED 37 Yes / No S M T W T F S SKED 38 Yes / No S M T W T F S SKED 39 Yes / No S M T W T F S SKED 40 Yes / No S M T W T F S

Time Date Day of Week Function

Bosch Security Systems | 9/04 | 50410D 49

Page 50

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DEL USER ? (COMMAND + 5 + 3)

DEL USER ? (COMMAND + 5 + 3)

This function allows a user to be deleted.

Enter the user number, not the passcode. (123 is as an example.)

This function will delete the passcode, Master User, and all sub-users associated with the user number.

1. Ensure your keypad shows idle disarmed text.

Press either the

Enter>

soft key or the ENTER

button.

5. If the user number entered is a valid user in the

system, the display will show

Are you sure?

Delete User 123?

2. Press the COMMAND key. The display shows

*System Command*

(123 is as an example.) If the user number entered is not a valid user in

3. Press the 5 key and then the 3 key.

the system, the display will show

currently not in use

This user is

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the DEL USER ?> prompt, press its adjacent soft key.

4. The display changes to show

deleted:

Enter user # to be

6. Press the

The display briefly shows that the user has been deleted before returning to idle text (123 is used as an example).

Yes>

soft key to delete the user.

The user text is not deleted when deleting a user. To modify a user’s text, see Add/Change User (Command 56).

50 Bosch Security Systems | 9/04 | 50410D

Page 51

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG RELAYS ? (COMMAND + 5 + 4)

CHG RELAYS ? (COMMAND + 5 + 4)

Your security company may program relays for automatic control and/or control from your keypad of devices such as premises lighting or entry gates. Contact them for further information regarding the use of relays in your security system.

1. Ensure your keypad shows idle disarmed text.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 5 key and then the 4 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Enter the relay number then press either the

Enter>

soft key or the ENTER button.

5. If the relay is valid and turned off, the display

changes to

currently off.

Change Relay* Relay 123 is

(123 is used as an example.) Press the

Turn on>

soft key to turn on the relay.

6. If the relay is valid and turned on, the display

changes to

currently on.

Change Relay* Relay 123 is

(123 is used as an example.) Press the

Turn off>

soft key to turn off the relay.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the CHG RELAYS ?> prompt, press its adjacent soft key.

4. The command center display changes

Relay* Enter relay number:

Valid entries are 1 to 128, depending how the system is configured.

*Change

7. The display returns to the

relay number:

Press the

<Exit

soft key to return to idle text.

*Change Relay* Enter

CHG PASSCODES ? (COMMAND + 5 + 5)

Description

Use this function to change your personal passcode without assistance from the security company.

Before you begin:

• Choose a new passcode three to six digits long. If

you choose a passcode with the same digit in consecutive order (for example “33” in 334697), take care when entering it.

Bosch Security Systems | 9/04 | 50410D 51

Page 52

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - CHG PASSCODES ? (COMMAND + 5 + 5)

• To avoid conflicting with other passcodes and

duress codes, your system does not let you change passcodes to an existing passcode or to within plus or minus 2 of an existing passcode. For example, if 1234 were an existing code, your system would not

5. The display changes to

Enter the new passcode. As soon as a number is pressed,

on the third line next to the asterisks.

Enter new passcode:

Entering:

appears

let you change your code to 1232, 1233, 1234, 1235, or 1236.

Using Chg Passcodes

1. Ensure your keypad shows idle disarmed text.

The passcode is shown as asterisks (*) when entered and advance from the right side of the display to the left until all passcode digits are entered.

2. Press the COMMAND key. The display shows

*System Command*

6. Press the ENTER button.

If an invalid passcode is entered, the command center will momentarily display

Passcode is

already in use. Please try again.

3. Press the 5 key and then the 5 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the CHG PASSCODES ?> prompt, press its adjacent soft key.

4. You will prompted for your passcode.

As soon as a number is pressed,

Entering:

on the third line next to the asterisks. The passcode is shown as asterisks (*) when

entered and advance from the right side of the display to the left until all passcode digits are entered.

appears

7. If the new passcode is valid, the display changes to

Enter new passcode again:

Enter the new passcode again. As soon as a number is pressed,

Entering:

appears

on the third line next to the asterisks.

The passcode is shown as asterisks (*) when entered and advance from the right side of the display to the left until all six passcode digits are entered.

8. If the passcode matches the previously entered

passcode, the display changes to

changed.

Passcode

52 Bosch Security Systems | 9/04 | 50410D

Page 53

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

If the passcode does not match, the command center will emit a error tone and display

Passcode

not changed.

• To avoid conflicting with other passcodes and

duress codes, your system does not let you change passcodes that are the same within plus or minus 2 of an existing passcode. For example, if 1234 were an existing code, your system would not let you add or change your code to 1232, 1233, 1234, 1235, or 1236.

• Choose an authority level for each area. Not

9. The display automatically returns to idle text after

three seconds.

assigning the authority level for an area denies the passcode access to that area.

1. Ensure your keypad shows idle disarmed text.

ADD/CHANGE USER (COMMAND + 5 + 6)

Use this function to add or change a user to your system without assistance from your security company. You need to know which user numbers are available, the authority level you want to assign to the new passcode and the areas in which it will be valid before you add it.

The user numbers identify users in reports transmitted from your system. Additionally, you will be able to change the following:

• the authority level (which determines what system

functions the passcode can access)

• the area number (which identifies which parts of

your security system the user will have access to)

• the name of the user

• the card number they use for access control

• whether they are a Master or Sub-User.

Contact your security company if you don’t know what user numbers, authority levels, or areas are available. See the Appendix for further information on adding passcodes.

Before you begin, keep these points in mind:

• Do not try to add new users without knowing the

available user numbers. An already defined user number will be overwritten when the new user is defined. These are two or three digit numbers, not to be confused with passcodes, that identify users at your security company.

• When choosing passcodes, choose a new passcode

three to six digits long. If you choose a passcode with the same digit in consecutive order (for example “33” in 334697), take care when entering it.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 5 key and then the 6 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the ADD/CHG USER ?> prompt, press its adjacent soft key.

4. The display changes to show

Enter user #:

Add / Change User

Bosch Security Systems | 9/04 | 50410D 53

Page 54

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

5. Enter the user number and press either the

soft key or the ENTER button.

Enter>

If your system has a D9412 or D7412 Control Panel, this menu allows the following User items to be changed:

• Passcode - Press the

<Passcode

soft key to

change the user’s passcode.

6. The display changes to show the user number

entered and the user’s name (if any). (User 2 is used as an example.) Press the

Continue>

soft key to proceed on to

changing the user’s information.

• Level - Press the

<Level

the user’s Authority Level.

• Name - Press the

Name>

the user’s name.

• Card - Press the

Card>

user’s card.

• Sub-User - Press the

soft key to change

soft key to change the

Sub-User>

soft key to

change the user’s sub-user status.

If there is no name for the user, the text appears in the second line.

(User 2 is used as an example.) Press the

Continue>

soft key to change the user’s

information.

USER 2

If your system has a D9112 or D7212 Control Panel, this menu allows the following User items to be changed:

• Name - Press the

Name>

soft key to change

the user’s name.

• Passcode - Press the

<Passcode

soft key to

change the user’s passcode.

• Level - Press the

<Level

soft key to change

the user’s Authority Level.

7. The display changes to

Add/Change Menu.

The display varies depending on the type of control panel that was installed in your system.

 My system has a D9412 or D7412 Control

Panel

 My system has a D9112 or D7212 Control

Panel

Add/Change Passcode

1. Pressing the

will allow you to add/change a user’s passcode.

<Passcode

or the

Passcode>

soft key

User 123 is used here as an example.

2. The display changes to User 123 Add a passcode

for this user? Press the Yes> soft key to add a new passcode. Go to Step 3.

Pressing the No> soft key advances to Add/Change Level, if the panel is a D9112 or D7212, or Add/Change Card, if the panel is a D9412 or D7412.

If the user already has an assigned passcode. it will be detected by the panel and will automatically go to Step 4.

54 Bosch Security Systems | 9/04 | 50410D

Page 55

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

3. The display changes to

Enter the new passcode. As soon as a number is pressed,

on the third line next to the asterisks.

The passcode is shown as asterisks (*) when entered and advance from the right side of the display to the left until all passcode digits are entered.

Press the ENTER button. If the passcode matches the previously enter

passcode, the display changes to Passcode added. Pressing the

Add/Change Level (if the panel is a D9112 or D7212) or Add/Change Card (if the panel is a D9412 or D7412).

Next>

Enter new passcode:

Entering:

soft key advances to the

appears

4. The display changes to User 123 Change this

user’s passcode?

Press the Press the

and skip ahead to Add/Change Level (if the panel type is a D9112 or D7212) otherwise if the panel is a D9412 or D7412, the Add/Change Card appears next.

You will prompted for the user’s passcode. As soon as a number is pressed,

on the third line next to the asterisks. It will appear on the display as asterisks (*).

Yes>

soft key to change the passcode.

No>

soft key not to change the passcode

Entering:

appears

If an invalid passcode is entered, the command center will momentarily display

already in use. Please try again.

If the passcode does not match, the command center will emit an error tone and display

Passcode is

Passcode not changed.

Pressing the Add/Change Level (if the panel is a D9112 or D7212) or Add/Change Card (if the panel is a D9412 or D7412).

Next>

soft key advances to the

Press the ENTER button. The display changes to Enter new passcode again:

Enter the new passcode again. Press the ENTER button. If an invalid passcode is entered, the command

center will momentarily display

Passcode is

already in use. Please try again.

If the passcode matches the previously enter passcode, the display changes to

Passcode

changed.

Bosch Security Systems | 9/04 | 50410D 55

Page 56

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

If the passcode does not match, the command center will emit an error tone and display

Passcode not changed

5. Press the

<Exit

soft key to return to the

Add/Change Menu

Add/Change Level

1. Pressing the

allow you to add/change a user’s authority level.

2. The display changes to

<Level

Level for this user?

Press the Press the

Passcode - if the panel is a D9112 or a D7212) or to Change Sub-User ID - if the panel is a D9412 or a D7412.

Press the and return to the Step 7).

3. The display changes to

Area 1?

Press the authority level in Area 1.

Press the in Area 1 and proceed to display user’s authorization in Area 2.

Press the and return to the Level changed display.

Yes>

soft key to add an Authority Level.

No>

soft key to advance to Add/Change

<Exit

soft key to exit out of this menu

Yes>

soft key to/add change this user’s

No>

soft key if the user isn’t authorized

<Exit

soft key to exit out of this menu

or the

Level>

soft key will

User 123 Add Auth.

Level changed.

display (Refer

Is this user authorized in

If the user is authorized in Area 1, the displays changes to User’s current authority level: 14 for Area 1.

(14 is used as an example here)

To change the Authority Level, Enter a new authority level (from 1 to 14), if desired, and press either the

Before determining the Authority Level for a user, please consult your security company to assist you in selecting the correct authority level.

Press the and return to the

4. Repeat Step 3 for each area through Area 8.

5. The display changes to

user’s Auth. Level?

Press the authority level in Area 1.

Press the Passcode (if the panel is a D9112 or a D7212) or to Change Sub-User ID (if the panel is a D9412 or a D7412).

Press the and return to the Step 7).

If the user is authorized in Area 1, the displays changes to Area 1.

(14 is used as an example here)

To change the Authority Level, Enter a new authority level (from 1 to 14), if desired, and press either the

Before determining the Authority Level for a user, please consult your security company to assist you in selecting the correct authority level.

Enter>

<Exit

soft key or the ENTER button.

soft key to exit out of this menu

Level changed

display.

User 123 Change this

Yes>

soft key to add/change this user’s

No>

soft key to advance to Add/Change

<Exit

soft key to exit out of this menu

Level changed.

display (refer to

User’s current authority level: 14

Enter>

soft key or the ENTER button.

for

56 Bosch Security Systems | 9/04 | 50410D

Page 57

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

<Exit

Press the and return to the

6. Repeat Step 5 for each area through Area 8.

7. Once the user’s authority level has been verified

for Area 8, the display changes to

Next>

If the changes to Add/Change Sub-User ID (for D9412/D7412 panels) or Add/Change Passcode (for D9112/D7212 panels).

soft key to exit out of this menu

Level changed.

display.

Level changed.

soft key is pressed, the display

Adding/Changing a User’s Name

1. Pressing the Name> soft key will change the

display to (JANE DOE is used as an example.)

2. To change the name use the following soft keys:

<? JANE DOE

If the changes to

<Exit

soft key is pressed, the display

Add / Change User Enter User #:

Pressing this soft key will display a series of help screens where the keypad can be used to enter specific letters.

Pressing either of these soft keys will cause the currently underlined character to change the previous or next character in the list. The available characters are A-Z, 0-9, @, #, $, &, *, /, -, _, ?, and +.

Pressing either of these soft keys will cause the cursor of the currently underlined character to move left to the previous position in the name or right to the next position in the name.

Another option is to use the numeric keys to add characters to the text. For the keys with letters, pressing the digit will allow you to cycle through the letters on the key. For instance, pressing '2' will display an A. Pressing it again will display a B, and pressing it a third time will display a C.

The '0' (zero) key will display a 0. The '1' key functions like a space bar - it puts a space in the current position, and advances to the next position.

3. Once the name appears as desired, press the

Continue>

4. The display will change to

soft key.

JANE DOE Is this correct?

At this point you can accept or reject the changes.

New user name is

Press the return to the main (depending on panel model).

Bosch Security Systems | 9/04 | 50410D 57

Yes>

soft key to accept the name and

Add/Change Menu

Page 58

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

D9412/D7412:

D9112/D7212:

Press the return to Step 1.

Add/Change Card

1. Pressing the

add/change a user’s access card or credential.

2. The display changes to either one of the following

depending on if an access card exists for the user:

User 123 Add Access Card for this user?

access card exists for that user.

<No

soft key to reject the name and

Card>

soft key will allow you to

- if no

3. If a card reader is connected to your system, the

display changes to

now.

Pressing the function and returns the display to idle text.

If the display changes to

Present card to card reader

<Exit

soft key exits out of this

D9210 not ready,

contact your security company.

Pressing the function and returns the display to idle text.

4. If the card you are trying to add to the system

already exists, an error tone sounds and the display changes to

<Exit

soft key exits out of this

Card already exists. Please try again.

Pressing the Pressing the

Add/Change Level.

User 123 Change this user’s Access Card?

access card already exists for this user and you wish to change it. (In both cases, 123 is used as an example)

Pressing the Pressing the

Add/Change Level.

Yes>

soft key will jump to Step 3.

No>

soft key will jump to

Yes>

soft key will jump to Step 3.

No>

soft key will jump to

-if an

Pressing the function and returns the display to idle text.

Then the display returns to

reader now.

Pressing the function and returns the display to idle text.

<Exit

soft key exits out of this

Present card to card

<Exit

soft key exits out of this

58 Bosch Security Systems | 9/04 | 50410D

Page 59

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)

5. If the card is accepted, the display changes to

either

Card added.

already exists in your system.

Pressing the function and returns the display to idle text.

Pressing the function and returns the display to either Add/Change Level.

<Exit

Next>

Card changed

soft key exits out of this

if the card

3. The display changes to

Press the sub-user 1.

Press the sub-user 2.

Press the sub-user 3.

Press the

/ Change User

4. If adding or changing a sub-user and a card reader

is connected to your system, the display changes to

Add

<Sub-User 1

<Sub-User 2

<Sub-User 3

Exit>

soft key to return to the main

display.

(or

Change) Sub-User 1: Present card to

card reader now.

Select Sub-User:

soft key to add or change

Add

Add/Change Sub-User ID

For each user in the system, there can be up to four access cards; one Master User (assigned in the prompt) and up to three sub-users.

1. Pressing the

add/change a user’s Sub-User access card or credential.

2. The display changes to

Sub-User IDs?

sub-user IDs.

Pressing the Pressing the

Add/Change Passcode.

Sub-User>

soft key will allow you to

User 123 Add/Change

to add or change any of this user’s

Yes>

soft key will jump to Step 3.

No>

soft key will jump to

Card>

If the display changes to your security company.

If 20 seconds elapse without pressing a key the display returns to idle text. Pressing the key exits out of this function and returns the display to the main

D9210 not ready

<Exit

Add / Change User

, contact

soft

display.

Bosch Security Systems | 9/04 | 50410D 59

Page 60

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DEFAULT TEXT ? (COMMAND + 5 + 7)

5. If the card you are trying to add to the system

already exists, an error tone sounds and the display changes to

Card already exists. Please try again.

Pressing the

Next>

soft key exits out of this function and returns the display to Add/Change Passcode depending on if a passcode already exists for the user.

If 20 seconds elapse without pressing a key returns the display to idle text. Pressing the

<Exit

soft key exits out of this function and returns the display to the main

Then the display returns to

reader now.

Add / Change User

Present card to card

display.

DEFAULT TEXT ? (COMMAND + 5 + 7)

This function allows the current state of the area for 3 seconds before returning to idle text.

Present the card to the reader to continue or press the

<Exit

soft key to exit out of this function and

return the display to idle text.

6. If the card is accepted, the display changes to

either

Card added.

Card changed

if the card

already exists in your system.

Pressing the

<Exit

soft key exits out of this

function and returns the display to the main

Change User

display.

Add /

1. Ensure your keypad shows idle disarmed text.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 5 key and then the 7 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the DEFAULT TEXT ?> prompt, press its adjacent soft key.

60 Bosch Security Systems | 9/04 | 50410D

Page 61

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - FIRE TEST ? (COMMAND + 5 + 8)

4. The current state of the area is displayed for 3

seconds before returning to idle text.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

FIRE TEST ? (COMMAND + 5 + 8)

Use this function to test fire points and other 24-hour points to be certain they function properly. You can review both the tested and untested points at your command center to help pinpoint any problems.

Upon initiation, the fire test will test the fire bell pattern on the bell output and ring the command center fire bell for 2 seconds. The AC will be disabled for 4 minutes in order to test the system’s battery power. If the battery cannot maintain the system for the 4-minute period, the command center will appear to go dead. If this happens, contact your security company. At the end of the 4-minute period, AC is returned to the system and the panel restores. A message will be sent to your security company upon initiation and completion of the Fire Test. During the

Fire Test, no 24-hour alarms will be sent to your security company.

If there is no activity on the system for 20 minutes, the system will automatically exit from the Fire Test.

Using Fire Test:

1. Ensure your keypad shows idle disarmed text.

Press NEXT> soft key repeatedly.

When you reach the FIRE TEST ?> prompt, press its adjacent soft key.

4. When the display shows

be tested

you can begin. (### is the number of

### points remain to

points). Test each point by first activating the detection

device to fault the point.

If you know the point number, you can enter it by pressing its number key and then the ENTER key.

The display will change to show the point that was entered. If the point is invalid the message “Invalid Point” or “This is not a valid walk point” appears.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 5 key and then the 8 key.

Bosch Security Systems | 9/04 | 50410D 61

Page 62

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - DISPLAY REV ? (COMMAND + 5 + 9)

5. As you fault each point, your command center will

display the point text for 60 seconds and ring the fire sounders for 2 seconds. This verifies that the detection device is working properly. Your system automatically resets smoke detectors.

Press the information about specific points that have not yet been tested.

The display changes to show the information for that point.

Point information>

soft key to see

• When a resettable point (such as a smoke

detector) is faulted, the display shows

Sensors…resetting…please wait…

seconds. During this time power is removed from smoke power relays.

• Faulting a point more than once does not

increment the test count. However, the command center emits a brief tone and displays the point text each time you fault the point allowing you to test multiple devices assigned to one point.

6. When the point has been tested, the display

changes to show

SMOKE DETECTOR tested.

for 5

Move through this list by pressing the

Point>

Press the

soft key.

<Exit

soft key to return to the

points remain to be tested.

Fire Test.

8. When all 24-hour points have been tested,

points remain to be tested

Press the The display momentarily shows

<Exit

soft key.

been tested.

###

before continuing the

is displayed.

All points have

7. During the Fire Test you may want to see the

points that remain untested by pressing the

untested pts>

The display shows ### pts untested.

soft key.

View

before returning to idle text.

DISPLAY REV ? (COMMAND + 5 + 9)

62 Bosch Security Systems | 9/04 | 50410D

1. Ensure your keypad shows idle disarmed text.

Page 63

D1260/D1260B | Owner's Manual | Part III: Advanced Commands -

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 5 key and then the 9 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the DISPLAY REV ?> prompt, press its adjacent soft key.

4. The display will change to Radionics D9412*

Version 6-40 (D9412 and 6-40 are used as an example, other

panels could be D9112, D7412, D7212)

SERVICE MENU ? (9 + 9 + Enter)

The service menu is used to access the following commands:

• View Log - Use this function to review events in

your system at your command center. Reviewing past events may help you identify problems. Viewing events does not require any additional equipment since the information is displayed at your command center. Events are stored in the panel’s memory in order of occurrence and tagged with the date and time.

• Print Log - The Print Log function lets you print

the events stored in your security system’s log. You can choose to print the entire log or set a start date and print the events recorded from that date up to today. Your system must include a parallel printer interface and a printer to perform this function.

• Display Rev (COMMAND + 5 + 9) - The

command will retrieve the panel’s software version and display it.

• Service Walk (D9412/D9112 only) – The

command will allow all the points on the system to be walk tested regardless of the type of point. For D7412 and D7212 panels this function must be added to the keypad’s menu. Contact your security company for more information.

• Default Text – This command will show the

current state of the area for 3 seconds before returning to idle text.

1. Ensure your keypad shows idle disarmed text.

5. The display will return to idle text after 5 seconds.

2. Press the 9 key twice.

3. Press the ENTER key.

4. The display changes to show the service menu.

Service Walk Test?>

Bosch Security Systems | 9/04 | 50410D 63

appears on D9412/D9112

Panels only

Page 64

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)

Using View Log

1. Press the

2. The display changes to Enter start date:

View Log ?>

soft key.

6. The display will show one of two ways depending

on if the date entered was for an event first in the log or not.

• If the date was for the first event in the log, it

will display the next latest event in the log.

Press the last event in the log.

Press the return to idle text.

3. Enter the start date in the form of mm/dd.

For example, to enter 7/14 as the start date, press

+ 7 + 1 + 4

Once you start entering digits, the

event>

key.

Press the return to idle text.

4. Press either the

button.

5. If the date entered is valid, the first event for that

date will appear.

Go to last event>

<Exit

soft key to exit this function and

soft key to go to the

Go to last

soft key is replaced with the

<Exit

soft key to exit this function and

Enter>

soft key or the ENTER

Enter>

soft

7. Press the

• If the date was for an event (not the first) in the

log, the display will be the same except the

<Previous

Press the return to idle text.

the log. If there are no more events in the log,

Log*

will appear.

Press the event in the log.

Press the return to idle text.

soft key has been added.

<Exit

soft key to exit this function and

Next>

soft key to go to the next event in

<Previous

<Exit

soft key to go to the previous

soft key to exit this function and

*End of

Press the return to idle text.

If the date entered is invalid (there are no events with that date in the log), it will display the next latest event in the log.

Press the return to idle text.

64 Bosch Security Systems | 9/04 | 50410D

<Exit

soft key to exit this function and

<Exit

soft key to exit this function and

Page 65

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)

Using Print Log

1. Press the

Print Log ?>

2. The display changes to

Press the

Print all events>

soft key.

Enter start date:

soft key to print all

events in the log. Press the

<Exit

soft key to exit this function and

return to idle text. The events are sent to a connected printer and

display changes to

Printing all events in history

for three seconds before returning to idle text.

4. If the date entered is valid, the events for that date

will be sent to a connected printer and the display will show before returning to idle text.

Printing events.

for three seconds,

Using Display Rev

1. Press the

Display Rev ?>

soft key.

2. The display will change to

Version 6-40

*Bosch D9412*

3. Enter the start date in the form of mm/dd.

For example, to enter 12/21 as the start date, press

1 + 2 + 2 + 1

Once you start entering digits, the

events>

soft key is replaced with the

Print all

Enter>

key. Press either the

Enter>

soft key or the ENTER

button.

soft

(D9412 and 6-40 are used as an example, other panels could be D9112, D7412, D7212).

3. The display will return to idle text after 5 seconds.

Using Service Walk Test

The Service Walk Test function is only available in the Service Menu for D9412 and D9112 panels. If the panel model is D7412 or D7212, the Service Walk Test will have to be enabled on the Function list for the command center through the panel’s programming.

1. When the display shows

be tested

you can begin. (### is the number of

### points remain to

points).

Bosch Security Systems | 9/04 | 50410D 65

Page 66

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)

If you know the point number, you can enter it by pressing its number key and

3. When all points have been tested,

remain to be tested

is displayed.

0 points

then the ENTER key. The display will change to show the point

that was entered. If the point is invalid the message “Invalid Point” or “This is not a valid walk point” appears.

Test each point by first opening and then closing the door or window or other detection device.

Check the display after testing each point. For

Press the

<Exit

soft key.

The display momentarily shows

been tested.

All points have

interior points, walking past the device once is sufficient. If any point does not test correctly, contact your security company for service.

2. During the Walk Test you may want to see the

points that remain untested by pressing the

untested pts>

soft key.

View

before returning to idle text.

The display shows

### pts untested.

Press the

Point information>

soft key to see information about specific points that have not yet been tested.

The display changes to show the information for that point.

Move through this list by pressing the

Point>

Press the

points remain to be tested.

soft key.

<Exit

soft key to return to the

before continuing the

###

Service Walk Test.

Using Default Text

This function allows the current state of the area for 3 seconds before returning to idle text.

1. Press the

Default Text?>

soft key to display the

current state of the area.

2. The current state of the area is displayed for 3

seconds before returning to idle text.

Using Setup

The Setup function is accessed by pressing the

Setup?

> soft key.

The adjustable functions that are available in this menu are:

• High Brightness,

66 Bosch Security Systems | 9/04 | 50410D

Page 67

D1260/D1260B | Owner's Manual | Part III: Advanced Commands - SERVICE MENU ? (9 + 9 + Enter)

• Low Brightness,

• Contrast.

Each of these selections have

<- Level +>

soft keys on either side of the display that allows you to increase (+) or decrease (-) the setting being displayed. The High and Low Brightness are associated to Command 49’s Bright Display and Dim Display settings.

Also shown in this menu is the Command Center address, whether the Encoding Tone is On or Off,

and the Command Center software revision.

Bosch Security Systems | 9/04 | 50410D 67

Page 68

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Working with Multiple Areas from a Single Command

• PERIMETR INST? (Perimeter On Instant),

Part IV: Multi-Area Use

Working with Multiple Areas from a Single

Command Center

Each of the functions described in the preceding section on Advanced Commands is presented as though your system includes only one area. If your system includes more than one area, it can be set up in one of two ways by the installing company:

• Each command center will only have access to the

local area to which it is assigned, or

• Each command center may access either some or

all areas beyond the one to which it is assigned. This factor is referred to hereafter as command center scope.

If your command center allows access to areas other than the local area (that is to say, has scope in other areas), then the command center will limit your access to those areas within the command center scope and for which your personal passcode has authority.

Given that you have access to areas beyond the local area, the means of accessing the various system functions depends upon the specific function.

For some functions, the command center allows you to select the area (or point) in which to perform the function. These “selectable” functions are:

• DISARM ?,

• MASTER ARM AREA ?.

• BYPASS A POINT? and

• UNBYPASS A POINT?

Another group of functions may automatically work in all areas in which you have passcode authority and which are within the scope of the command center. These are:

• Turning On Multiple Areas with a Passcode,

• Turning Off Multiple Areas with a Passcode,

• DISARM ALL ?,

• MASTER ARM ALL?,

• VIEW MEMORY?,

• WALK TEST?,

• RESET SENSORS ?,

• ADD PASSCODES ?,

• FIRE TEST?,

• VIEW POINT STATUS? and

• VIEW AREA STATUS?

Some functions may be area-specific. To perform these functions, you must first use the MOVE TO AREA ? function (Command 50) to gain access to the desired area. Once in the desired area you can perform the functions you wish. Area-specific functions include:

• PERIMETR DELAY ? (Perimeter On Delay),

• PERIMETR PART ? (Perimeter On Partial),

• EXTEND CLOSING ?,

• WATCH MODE ?,

• COMMAND 7 ?,

• COMMAND 9 ? and

• CHG DISPLAY ?.

A last group of functions don’t relate to specific areas and are thus system-wide. These are:

• SEND REPORT?,

• REMOTE PROG ?,

• CHG TIME/DATE ?,

• CHG SKEDS ?,

• DEL PASSCODES ?,

• CHG RELAYS ?,

• CHG PASSCODES ?,

• PRINT LOG ? and

• VIEW LOG?

View Area Status

Use this function when you need to know the status (whether armed or disarmed) of areas other than the one you’re in.

1. Ensure your keypad shows idle disarmed text.

2. Press the

Menu.

3. Press

AREA STAT ?>

Press the adjacent soft key.

Menu>

Next>

key to enter the Command

repeatedly until you reach the

prompt.

VIEW

68 Bosch Security Systems | 9/04 | 50410D

Page 69

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - View Point Status

4. The display will change to show on the top line the

area name and the current status on the second line.

5. The top line indicates that you are still in View

Point Status mode. The second line will display the point text.

Pressing the

Next>

soft key will change the display to the next area and remain for 20 seconds or until the

Next>

soft key is pressed for the next area. If the time has elapsed, the display returns to idle text.

Pressing the

<Previous

soft key will change the

display to the previous area.

5. Press the

<Exit

soft key to return to idle text.

View Point Status

Use this function to identify the number or location of each point in an area, and to show the current condition of any point you select.

1. Ensure your keypad shows idle disarmed text.

2. Press the

Menu.

3. Press

PT STATUS ?>

Press the adjacent soft key.

4. In this example, Area 1 is the area and there are

eight points assigned to area 1 that can be viewed.

Menu>

Next>

key to enter the Command

repeatedly until you reach the

prompt.

VIEW

Pressing the point in the area whereas the

Next>

soft key takes you to the next

<Previous

will take you to the previous point in the area. To view the status of a point, press the

key.

6. After pressing the

Status>

key, the command

center will display the following information:

Refer to Table 5 for more information.

Table 5: Screen Area Definitions

Line # Area Name Definition

Area # This may display numbers 1 to 8. 1 Pt # This may display point numbers 1

to 127 and 129 to 247,

2 (Point

State), HW

Normal indicates that the point

is not in the faulted state.

Open indicates that the point

is in an open state.

Short indicates that the point

is in a shorted state.

Missing indicates that the point

is missing.

soft key

Status>

soft

Press the the area; press the last point in the area. You may press the

Next>

soft key to view the first point in

<Previous

soft key to view the

<Exit

soft

key at any time to exit this function.

Bosch Security Systems | 9/04 | 50410D 69

Page 70

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - MOVE TO AREA ? (COMMAND + 5 + 0)

MOVE TO AREA ? (COMMAND + 5 + 0)

With this function you can perform tasks in an area

4. You may be prompted for your passcode. If so,

enter your passcode and press the ENTER key. It will appear on the display as asterisks (*).

other than the one you’re in without having to physically go to that area. Your access to other areas is limited by the scope of the command center and your authority level. For example, if your passcode gives you authority to all 8 areas, but the command center you’re working with is limited in scope to areas 1 and

The

<Exit

2, then you will only be able to move to either area 1 or area 2.

Upon moving to another area, the range of tasks you may perform depends upon the command center you’re working with. Once you’ve performed a task (such as Turning the Area On), the command center reverts back to its programmed area after 10 seconds. Thus only one task can be performed in another area at a time.

1. Ensure your keypad shows idle disarmed text.

return to idle text.

5. The command center will then display the Area

Name Text of each area that falls within the scope of the command center and authority level of the user, if applicable. (All 8 area names are shown as an example).

soft key will quit this function and

If the user's authority level does not permit access to a certain area and that area is not within the scope of the command center, or the area is not enabled, it will not appear in the display.

If the area you wish to move to does not appear in this list, press the Next> key to display additional areas.

2. Press the COMMAND key. The display shows

*System Command*

3. Press the 5 key and then the 0 key.

If you prefer, you may use the Command Menu in place of steps 2 and 3 to initiate this function.

Press the MENU> soft key to enter the Command Menu.

Press NEXT> soft key repeatedly.

When you reach the MOVE TO AREA ?> prompt, press its adjacent soft key.

To select an area, simply press the soft key corresponding to the Area Name.

Moving to…AREA 1 WAREHOUSE

displays briefly, and then the text of the area you’ve moved to is displayed (AREA 1 WAREHOUSE is used as an example here).

70 Bosch Security Systems | 9/04 | 50410D

Page 71

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning On the System

7. You are now able to perform tasks in this area.

The number of areas to which you can move will be limited by the scope of the command center.

If you try to move to an area for which the command center does not have scope,

AUTHORITY*

8. When you have completed all tasks in the area

you’ve moved to, simply allow the command center to time-out and revert to the area from which you started or enter the Move to Area function again.

is displayed.

*NO

4. The display changes and shows

ALL ?

with the following options:

•

<Previous

that can be armed (based on passcode and authority level)

•

Next>

that can be armed (based on passcode and authority level)

•

Arm>

passcode and authority level)

•

<Exit

text

soft key – will scroll to the last area

soft key – will scroll to the first area

soft key – will arm all areas (based on

soft key – will return the display to idle

MASTER ARM

Turning On the System

Turning on Selected Areas

Areas covered in the scope of the command center can be armed individually by accessing the Master Arm function through the menu.

1. Press the

Menu.

2. Press the

reach the the adjacent soft key.

3. You will prompted for your passcode. It will

appear on the display as asterisks (*).

Menu>

Next>

MASTER ARM ?>

key to enter the Command

soft key repeatedly until you

prompt then press

5. If the

6. Pressing the

Next>

soft key is pressed, the first area that can be armed (based on passcode entered and user authority level) is displayed (

WAREHOUSE

area that can be armed).

is used an example of the first

Arm>

soft key will cause

WAREHOUSE is now arming…

seconds before the prompt to arm the next available area is displayed.

AREA 1

to display for 3

Turning on Multiple Areas with a Passcode

You can use your personal passcode to turn on both perimeter and interior points in all areas where your passcode has authority. If there are areas already turned on, this function turns on all areas that are off without changing the status of the areas that are already on.

Bosch Security Systems | 9/04 | 50410D 71

Page 72

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turn On the Entire System Without Delays

1. Enter your passcode and press ENTER.

2. The command center will display the following:

Command center scope and/or your authority level limit the actual number of areas you may turn on. For example, if you have authority to arm all 8 areas but the scope of the command center you’re using is limited to areas 1, 2, and 5, then you will only be able to turn on areas 1, 2, and 5.

3. If a point is faulted (door or window open for

example), see Turning On the System (Arming) With Doors or Windows Open for further information.

Faulted Points in Other Areas

If there is a faulted point in an area you select (other than the one you are in), an example here) appears for 3 seconds and then the display returns to the area disarmed idle text.

Check Area 1

(1 is used as

Turn On the Entire System Without Delays

You can use this Command Menu function to turn on the entire system, both perimeter and interior, without delays. You may use this function in all of the areas or some of the areas where your passcode has authority. If there are areas already turned on, this function turns on all areas that are off without changing the status of the areas that are already on.

Turning on All or Selected Areas

Areas covered in the scope of the command center can be armed individually by accessing the Master Arm function through the menu.

1. Press the

Menu.

2. Press the

reach the press the adjacent soft key.

3. You will prompted for your passcode. It will

appear on the display as asterisks (*).

Menu>

Next>

key to enter the Command

soft key repeatedly until you

MASTER ARM INST ?>

prompt then

If there is a faulted point in more than one area and the system is being armed, the display will prompt

Area 1 3

and 3.

Try one of the following:

• Clear faulted points (close doors and/or windows)

• Bypass faulted points (if your system and/or

• Force arm (if your system and/or authority allows).

meaning there are faulted points in Areas 1

and return to step 1.

authority allows) and return to step 1.

See Turning On the System (Arming) With Doors or Windows Open for more information.

Check

4. The display changes and shows

ALL ?

with the following options:

•

<Previous

that can be armed (based on passcode and authority level)

•

Next>

that can be armed (based on passcode and authority level)

•

Arm>

passcode and authority level)

<Exit

•

text

soft key – will scroll to the last area

soft key – will scroll to the first area

soft key – will arm all areas (based on

soft key – will return the display to idle

MASTER ARM

72 Bosch Security Systems | 9/04 | 50410D

Page 73

Next>

5. If the

can be armed (based on passcode entered and user authority level) is displayed (

WAREHOUSE

area that can be armed).

6. Pressing the

WAREHOUSE is now arming…

seconds before the prompt to arm the next available area is displayed.

7. Once all available areas have been displayed, the

display returns to

8. To instantly arm all the areas that are within the

scope of the command center, press the key.

9. This display changes to show

WAREHOUSE All On Instant

all areas are armed.

soft key is pressed, the first area that

AREA 1

is used an example of the first

Arm>

soft key will cause

ARM INSTANT ALL ?

AREA 1

to display for 3

Arm>

soft

AREA 1

indicating that the

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use -

Turning Off the System

Turning Off Multiple Areas with a Passcode

This function is useful for turning off multiple areas with a few keystrokes. It is quicker than disarming several areas independently. Your passcode must have the proper authority level for each area.

• After enter your passcode, the following will

display

areas are now disarmed.

may appear due to what areas are in the scope of the command center.

• When an area is turned on (armed), you must enter

a door programmed for entry delay time. Opening the door, starts the entry delay time. Failing to turn off the system before the entry delay time expires or entering through a door not programmed for entry delay time, causes an alarm.

• If this happens, silence the alarm by entering your

personal passcode and pressing ENTER. Call your security company to let them know that it is not an emergency situation.

Turning Off Multiple Areas with Disarm All

• This function turns off multiple areas with a few

keystrokes. It is quicker than disarming several areas independently. Your passcode must have the proper authority level for each area. This function works the same as entering your passcode to disarm, but allows the Disarm All feature to be included in the Command Menu.

• When an area is turned on (armed), you must enter

• If this happens, silence the alarm by entering your

personal passcode and pressing ENTER. Call your security company to let them know that it is not an emergency situation.

1. The display initially shows that the system is

armed.

Disarm: 12345678 All user-authorized

(Not all area number

Bosch Security Systems | 9/04 | 50410D 73

Page 74

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning Off the System

2. Press the

Menu.

Menu>

key to enter the Command

7. If the

Disarm>

areas, the display changes to show

soft key is pressed to disarm all

12345678 All user-authorized areas are now

3. Press the

reach the adjacent soft key.

4. If entering through a door which is part of an area

that is armed, the display changes to show:

5. Enter your passcode and press ENTER.

The passcode is shown as asterisks (*) when entered and advance from the right side of the display to the left until all the passcode digits are entered.

Next>

soft key repeatedly until you

DISARM ?>

prompt then press the

disarmed.

turned off. Command center scope and/or your authority level limit the actual number of areas you may turn off.

For example, if you have authority to disarm all 8 areas but the scope of the command center you’re using is limited to areas 1, 2, and 5, then you will only be able to turn off areas 1, 2, and 5.

Turning Off Selected Areas

If your passcode has the proper authority level this function allows you to turn off areas other than the one you are in.

1. The display initially shows that the system is

armed.

indicating that all areas are being

Disarm:

6. If the entered passcode is valid, the display

changes to show DISARM ALL?

Press the areas.

Press the area (see Turning Off Selected Areas).

Press the armed area.

Press the

Disarm>

Next>

<Previous

<Exit

soft key to disarm all armed

soft key to go to the first armed

soft key to go to the last

soft key to return to idle text.

2. Press the

Menu.

3. Press the

reach the adjacent soft key.

4. If entering through a door which is part of an area

that is armed, the display changes to show:

Menu>

Next>

DISARM ?>

key to enter the Command

soft key repeatedly until you

prompt then press the

74 Bosch Security Systems | 9/04 | 50410D

Page 75

D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Turning Off the System

5. Enter your passcode and press ENTER.

The passcode is shown as asterisks (*) when entered and advance from the right side of the display to the left until all the passcode digits are entered.

6. If the entered passcode is valid, the display

changes to show

DISARM ALL?

Press the

Disarm>

soft key to disarm all armed

areas.

7. Press the

Next>

soft key to go to the first armed

area.

8. The display changes to show

DISARM AREA 1 ?

(or the first area that is armed).

Press the Press the

Disarm> Next>

soft key to disarm this area.

soft key to scroll through the

remaining areas you have the authority to turn off. To disarm the area, press the

Disarm>

soft key.

9. After turning off other areas, the command center’s

display returns to the idle text for the area you are in.

Bosch Security Systems | 9/04 | 50410D 75

Page 76

D1260/D1260B | Owner's Manual | Appendix - Supplementary Information for Adding Passcodes

If you are having trouble understanding the concept of

Appendix

Supplementary Information for Adding

Passcodes

Use the information contained in this Supplement to help you add user passcodes.

User Authority Levels

Your security company uses the information contained on this page to establish authority levels for system users. For each of the 1- 14 authority levels, each command center function is either enabled (E), disabled (blank), or Passcode enabled (P). A function that is enabled (E) is available to all users. A function that is passcode enabled (P) is only available to users assigned an authority level that includes that function. If you do not want a particular command included in a given authority level, leave it blank.

authority levels, try this simple exercise. Refer to the column titled E/P on the next page. Notice that your security technician has marked some of the cells in this column with the letter “E”, others the letter “P”, while others are left blank. An “E” indicates that this function is enabled for all authority levels. A “P” indicates that the function is passcode protected. Look across the same row, and notice that some of the cells in the authority level area have the letter “E”. For each authority level in which an “E” appears, this function is enabled (with a passcode required). A blank cell in the E/P column means that this function is unavailable for any authority level.

Under the heading Authority Level, you’ll see columns 1-14, representing the fourteen authority levels. Now look at the column labeled 1. Following down this column, you’ll see that some cells are blank while some contain the letter “E”, which stands for enabled. Wherever there is an “E”, it means that that function is available to users with an authority level of 1.

Passcode Worksheet

The passcode worksheet presents the information discussed previously onto one page, and also includes the user’s ID number, assigned passcode, and his or her name.

An important piece of information included in the passcode worksheet is the listing of areas to which the user has access, along with the authority level assignment for each of those areas.

User Interface

# Functions* Command E/P 1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 Disarm ? 2 Master Arm Delay ? CMD 1 P E E E E E 3 Master Arm Instant? CMD 11 E E 4 Perimeter Instant ? CMD 2 P E E E E 5 Perimeter Delay ? CMD 3 P E E E E 6 Watch Mode ? CMD 6 E E E E 7 Perimeter Part ? CMD 8 P E E E E 8 View Area Status ? P E E 9 View Memory ? CMD 40 E E E E 10 View Pt Status ? E E E E 11 Walk Test ? CMD 44 E E E 12 Fire Test ? CMD 58 P E E 13 Send Report ? CMD 41/42 P 14

♦Door Control ? ♦Cycle Door ? ♦Unlock Door ? ♦Secure Door ?

♦Access Control Level?

15 Change Display ? CMD 49 E E 16 Change Time/Date ? CMD 45 E E 17 Change Passcode ? CMD 55 P E 18 Add User ? CMD 56 P E 19 Del User ? CMD 53 P E 20 Extend Close ? CMD 51 P 21 View Log ? E E

CMD 46 P E E E E E E E E E E P E

Authority Levels

E E E E E

76 Bosch Security Systems | 9/04 | 50410D

Page 77

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

22 Print Log ? P E 23 User Command 7 ? CMD 7 P 24 User Command 9 ? CMD 9 P 25 Bypass a Point ? CMD 0 P E E E E 26 Unbypass a Point ? CMD 00 P E E E E 27 Reset Sensors ? CMD 47 E E E E E 28 Change Relays ? CMD 54 P E E 29 Remote Program ? CMD 43 P E E E E 30 Move To Area ? CMD 50 P E E 32 Display Rev ? CMD 59 E E 33 Service Walk ? P 34 Default Text ? CMD 57 P 35 Change Skeds ? CMD 52 P E

* Command Center Function Authority Level Options: Blank = Disabled, E = Enabled. ♦ D9412G/D7412G only.

Authority Level 15 can not be edited.

Authority Levels

User Interface

# Functions* Command E/P 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Custom Functions

128 Custom Function 128 P E 129 Custom Function 129 P E 130 Custom Function 130 P E 131 Custom Function 131 P E 132 Custom Function 132 P E 133 Custom Function 133 P E 134 Custom Function 134 P E 135 Custom Function 135 P E 136 Custom Function 136 P E 137 Custom Function 137 P E 138 Custom Function 138 P E 139 Custom Function 139 P E 140 Custom Function 140 P E 141 Custom Function 141 P E 142 Custom Function 142 P E 143 Custom Function 143 P E

♦Access Levels** ♦ Security Level ?

♦ Disarm Level ?

* Command Center Function Authority Level Options: Blank = Disabled, E = Enabled.

Authority Level 15 can not be edited.

♦ D9412G/D7412G only.

Authority Levels

E M M P P P D E I D D D D

** Access Authority Level Options:

Security Level?

Disarm Level?

M = Any Armed State, P = Perimeter Armed, D = Disarmed, Blank = No Access

I = Disarm to Perimeter Instant, D = Disarm All, Blank = No Disarm Rights

Bosch Security Systems | 9/04 | 50410D 77

Page 78

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 000 to 038)

User User Area Authority ### Passcode Group 1 2 3 4 5 6 7 8 User Name

000 001 002 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 003 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 004 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 005 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 006 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 007 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 008 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 009 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 010 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 011 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 012 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 013 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 014 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 015 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 016 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 017 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 018 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 019 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 020 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 021 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 022 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 023 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 024 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 025 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 026 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 027 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 028 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 029 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 030 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 031 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 032 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 033 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 034 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 035 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 036 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 037 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 038 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __

2 3 __ __ __

123456

________

____

15 15 15 15 15 15 15 15

__ __ __ __ __ __ __ USER 1

Note:

Text shown in Times font (ex. 15) indicates sample text.

SERVICE

PASSCODE

USER 2 USER 3 USER 4 USER 5 USER 6 USER 7 USER 8 USER 9 USER 10 USER 11 USER 12 USER 13 USER 14 USER 15 USER 16 USER 17 USER 18 USER 19 USER 20 USER 21 USER 22 USER 23 USER 24 USER 25 USER 26 USER 27 USER 28 USER 29 USER 30 USER 31 USER 32 USER 33 USER 34 USER 35 USER 36 USER 37 USER 38

Product Handler Note: RADXUSR1 is for Users 000 - 124; RADXUSR2 is for Users 125 - 249.

78 Bosch Security Systems | 9/04 | 50410D

Page 79

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

♦ User (Token) Worksheet (User 000 to 038) D9412G/D7412G Only

User Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3

Site Card Data Site Card Data Site Card Data Site Card Data

## #

Not Available

000

001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038

Bosch Security Systems | 9/04 | 50410D 79

Page 80

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 039 to 075)

User User Area Authority

### Passcode Group 1 2 3 4 5 6 7 8 User Name

039 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 040 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 041 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 042 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 043 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 044 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 045 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 046 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 047 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 048 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 049 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 050 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 051 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 052 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 053 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 054 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 055 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 056 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 057 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 058 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 059 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 060 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 061 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 062 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 063 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 064 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 065 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 066 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 067 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 068 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 069 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 070 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 071 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 072 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 073 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 074 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 075 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __

USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER

39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

80 Bosch Security Systems | 9/04 | 50410D

Page 81

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

♦ User (Token) Worksheet (User 039 to 075) D9412G/D7412G Only

User Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3

### Site Card Data Site Card Data Site Card Data Site Card Data

039

040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075

Bosch Security Systems | 9/04 | 50410D 81

Page 82

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 076 to 114) (101-249 = D9412G only)

User User Area Authority ### Passcode Group 1 2 3 4 5 6 7 8 User Name

__ __ __ __ __ __

076 077 __ __ __ __ __ __ 078 __ __ __ __ __ __ 079 __ __ __ __ __ __ 080 __ __ __ __ __ __ 081 __ __ __ __ __ __ 082 __ __ __ __ __ __ 083 __ __ __ __ __ __ 084 __ __ __ __ __ __ 085 __ __ __ __ __ __ 086 __ __ __ __ __ __ 087 __ __ __ __ __ __ 088 __ __ __ __ __ __ 089 __ __ __ __ __ __ 090 __ __ __ __ __ __ 091 __ __ __ __ __ __ 092 __ __ __ __ __ __ 093 __ __ __ __ __ __ 094 __ __ __ __ __ __ 095 __ __ __ __ __ __ 096 __ __ __ __ __ __ 097 __ __ __ __ __ __ 098 __ __ __ __ __ __ 099 __ __ __ __ __ __ 100 __ __ __ __ __ __ 101 __ __ __ __ __ __ 102 __ __ __ __ __ __ 103 __ __ __ __ __ __ 104 __ __ __ __ __ __ 105 __ __ __ __ __ __ 106 __ __ __ __ __ __ 107 __ __ __ __ __ __ 108 __ __ __ __ __ __ 109 __ __ __ __ __ __ 110 __ __ __ __ __ __ 111 __ __ __ __ __ __ 112 __ __ __ __ __ __ 113 __ __ __ __ __ __ 114 __ __ __ __ __ __

____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____

__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __

__ __ __ __ __

USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER

76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114

82 Bosch Security Systems | 9/04 | 50410D

Page 83

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

♦ User (Token) Worksheet (User 076 to 114) D9412G/D7412G Only (101-249 = D9412G only)

User

Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3

###

076 077

078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114

Site Card Data Site Card Data Site Card Data Site Card Data

Bosch Security Systems | 9/04 | 50410D 83

Page 84

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 115 to 150) (101-249 = D9412G only)

User User Area Authority

### Passcode Group 1 2 3 4 5 6 7 8 User Name

115 116 __ __ __ __ __ 117 __ __ __ __ __ 118 __ __ __ __ __ 119 __ __ __ __ __ 120 __ __ __ __ __ 121 __ __ __ __ __ 122 __ __ __ __ __ 123 __ __ __ __ __ 124 __ __ __ __ __

125 126 __ __ __ __ __ 127 __ __ __ __ __ 128 __ __ __ __ __ 129 __ __ __ __ __ 130 __ __ __ __ __ 131 __ __ __ __ __ 132 __ __ __ __ __ 133 __ __ __ __ __ 134 __ __ __ __ __ 135 __ __ __ __ __ 136 __ __ __ __ __ 137 __ __ __ __ __ 138 __ __ __ __ __ 139 140 __ __ __ __ __ 141 __ __ __ __ __ 142 __ __ __ __ __ 143 __ __ __ __ __ 144 __ __ __ __ __ 145 __ __ __ __ __ 146 __ __ __ __ __ 147 __ __ __ __ __ 148 __ __ __ __ __ 149 __ __ __ __ __ 150 __ __ __ __ __

__ __ __ __ __

End RADXUSR1 Handler

USER USER USER USER USER USER USER USER USER USER

USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER

115 116 117 118 119 120 121 122 123 124

125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150

84 Bosch Security Systems | 9/04 | 50410D

Page 85

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Token) Worksheet (User 115 to 150) (101-249 = D9412G only)

User

Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3

###

115

116 117 118 119 120 121 122 123 124

125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150

Site Card Data Site Card Data Site Card Data Site Card Data

End RADXUSR1 Handler

Bosch Security Systems | 9/04 | 50410D 85

Page 86

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 151 to 189) (101-249 = D9412G only)

User User Area Authority ### Passcode Group 1 2 3 4 5 6 7 8 User Name

USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER

151_ 152_ 153_ 154_ 155_ 156_ 157_ 158_ 159_ 160_ 161_ 162_ 163_ 164_ 165_ 166_ 167_ 168_ 169_ 170_ 171_ 172_ 173_ 174_ 175_ 176_ 177_ 178_ 179_ 180_ 181_ 182_ 183_ 184_ 185_ 186_ 187_ 188_ 189_

151 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 152 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 153 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 154 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 155 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 156 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 157 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 158 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 159 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 160 __ __ __ __ __ __ ____ __ __ 161 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 162 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 163 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 164 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 165 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 166 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 167 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 168 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 169 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 170 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 171 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 172 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 173 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 174 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 175 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 176 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 177 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 178 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 179 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 180 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 181 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 182 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 183 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 184 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 185 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 186 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 187 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 188 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 189 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __

__ __ __ __ __

86 Bosch Security Systems | 9/04 | 50410D

Page 87

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Token) Worksheet (User 151 to 189) (101-249 = D9412G only)

User Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 ### Site Card Data Site Card Data Site Card Data Site Card Data 151

152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189

Bosch Security Systems | 9/04 | 50410D 87

Page 88

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 190 to 226) (101-249 = D9412G only)

User User Area Authority ### Passcode Group 1 2 3 4 5 6 7 8 User Name

190 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 190 191 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 191 192 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 192 193 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 193 194 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 194 195 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 195 196 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 196 197 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 197 198 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 198 199 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 199 200 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 200 201 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 201 202 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 202 203 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 203 204 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 204 205 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 205 206 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 206 207 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 207 208 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 208 209 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 209 210 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 210 211 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 211 212 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 212 213 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 213 214 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 214 215 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 215 216 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 216 217 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 217 218 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 218 219 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 219 220 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 220 221 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 221 222 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 222 223 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 223 224 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 224 225 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 225 226 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ USER 226

88 Bosch Security Systems | 9/04 | 50410D

Page 89

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

♦ User (Token) Worksheet (User 190 to 226) D9412G/D7412G Only (101-249 = D9412G only)

User

Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3

###

190

191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226

Site Card Data Site Card Data Site Card Data Site Card Data

Bosch Security Systems | 9/04 | 50410D 89

Page 90

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (User 227 to 249) (101-249 = D9412G only)

User User Area Authority ### Passcode Group 1 2 3 4 5 6 7 8 User Name

227 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 228 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 229 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 230 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 231 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 232 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 233 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 234 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 235 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 236 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 237 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 238 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 239 240 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 241 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 242 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 243 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 244 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 245 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 246 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 247 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 248 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __ 249 __ __ __ __ __ __ ____ __ __ __ __ __ __ __ __

__ __ __ __ __ __ ____ __ __ __ __ __ __ __ __

USER

227

USER

228

USER

229

USER

230

USER

231

USER

232

USER

233

USER

234

USER

235

USER

236

USER

237

USER

238 USER 239 USER

240 USER

241 USER

242 USER

243 USER

244 USER

245 USER

246 USER

247 USER

248 USER

249

90 Bosch Security Systems | 9/04 | 50410D

Page 91

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Token) Worksheet (User 227 to 249) (101-249 = D9412G only)

User

Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3

###

227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249

Site Card Data Site Card Data Site Card Data Site Card Data

Bosch Security Systems | 9/04 | 50410D 91

Page 92

D1260/D1260B | Owner's Manual | Appendix - Passcode Worksheet

User (Passcode) Worksheet (Blank)

###

Passcode

__ __ __ __ __ __ ____ __ __ __ __ __ __ __ __

User

Group

1 2 3 4 5 6 7 8

Area Authority User

USER

___ USER

___ USER ___ USER

___ USER

___

User Name

92 Bosch Security Systems | 9/04 | 50410D

Page 93

User (Token) Worksheet (Blank)

Master ID ###-0 Sub-User ###-1 Sub-User ###-2 Sub-User ###-3 Use

###

Site Card Data Site Card Data Site Card Data Site Card Data

D1260/D1260B | Owner's Manual | Appendix - Security System Limitations

Security System Limitations

Not even the most advanced security system can guarantee protection against burglary, fire, or environmental threats. All security systems are subject to possible compromise or failure-to-warn for a variety of reasons including, but not limited to, the following:

• If sirens or horns are placed outside the hearing

range of people in remote areas of the building or in areas, which are frequently closed off, they do not provide the intended protection.

• If intruders gain access through unprotected points

of entry, the system will not detect their entrance.

• If intruders have the technical means of bypassing,

jamming, or disconnecting all or part of the system, they will not be detected.

• If the AC power supply is OFF and the back-up

battery is either missing or dead, sensors will not detect intrusion.

• Smoke detectors cannot detect smoke in chimneys,

walls, or roofs, or smoke blocked by a closed door. They may not detect smoke or fire on a level of the building different from the one on which they are located. Smoke detectors may not be able to warn in time about fires started by explosions, improper storage of flammables, overloaded electrical circuits, or other types of hazardous conditions.

• If phone lines are out of service, reports from the

security system to the Security Company cannot be sent unless there is an alternate means of communication. Telephone lines are vulnerable to compromise by several means.

Inadequate maintenance and failure to test are the most common causes of alarm failure. It is strongly recommended that you test your system once a week to be sure that all system components are working properly.

Bosch Security Systems | 9/04 | 50410D 93

Page 94

D1260/D1260B | Owner's Manual | Appendix - Fire Safety and Evacuation

Although having a security system may make you eligible for reduced insurance premiums, the system is no substitute for insurance. Warning

Figure 5: Smoke Detector Locations (Elevation

View)

devices cannot compensate you for loss of life or property.

Fire Safety and Evacuation

Residential fire is a leading cause of accidental death. Most fire related deaths occur at night when occupants suffocate in their sleep from smoke and toxic gases, rather than from burns. To help reduce this risk, the following program should be implemented.

2 2

1. Minimize fire hazards. Smoking in bed, cleaning

with flammable liquids such as gasoline, leaving children home alone, and using unsafe holiday decorations are some of the common causes of household fire.

2. Install a fire alarm system. The primary purpose of

this system is to protect lives by giving the earliest possible warning of danger.

3. A smoke detector should be provided to protect

each sleeping area in a home (Figure 4 and Figure 5).

Figure 4: Smoke Detector Locations (Plan View)

4 5

1 - Smoke Detector 2 - TV Room 3 - Bedroom

4 - Dining Room 5 - Kitchen 6 - Living Room

1 - Smoke Detector 2 - Bedroom

4. Practice an escape plan. Because there may be

very little time between detection of a fire and the time it becomes deadly, it is important that every member of the family understand how to quickly evacuate according to the plan.

5. Plan both primary and alternate escape routes.

Since stairwells and hallways may be blocked during a fire, exiting through a bedroom window must be a part of the escape plan. If the sleeping area is above the ground floor, install a means of safely descending outside the building if one does not already exist.

6. As a part of this plan, all family members should

arrange to meet at a location away from the house (such as a neighbor’s house) so you will know that everyone is accounted for.

Figure 6: Escape Route

3 345

1 - Fire 2 - Escape Routes 3 - Bedroom 4 - Kitchen

5 - Dining Room 6 - Living Room 7 - Smoke Detector

7. If it is determined that the alarm was accidentally

sounded, the bell should be silenced, the detectors reset, and your security company notified immediately that there is no emergency situation.

94 Bosch Security Systems | 9/04 | 50410D

Page 95

D1260/D1260B | Owner's Manual | Appendix - Standard Displays

Standard Displays

Your command center uses standard and custom displays to show the status of the security system. Many standard displays are described below. Your system may not use all of them. Descriptions of your custom text follow.

System Command

Displays when you press the COMMAND key. The system is waiting for you to enter a one or two digit number to complete the command.

Exit Now

Arming your system starts exit delay time. The command center emits a repeating beep tone and displays 3 seconds and then displays

AREA 1 WARE HOUSE is now arming

Exit Now!

for

Enter Passcode to Disarm

When the system is turned on, entering through a delay door starts entry delay time.

The command center emits a tweedle tone and alternates between

ENTER key to disarm is in entry delay

an example.) You must turn off the system before entry delay time

expires to avoid creating an alarm event.

Enter Passcode and press the

and

AREA 1 WAREHOUSE

. (AREA 1 WAREHOUSE is used as

No Authority

The system does not recognize the passcode entered.

Perimeter Delay

Indicates that the perimeter is armed (turned on) with entry/exit delay time. (See Turning On the System With

Delays

)

Perimeter Instant

Indicates that the perimeter is armed (turned on) without entry/exit delay time. (See Turning On the

System Without Delays

First Disarm – Area must be disarmed first

Indicates that the function requested can only be performed when the area is disarmed. Disarm the area to perform the function.

Bosch Security Systems | 9/04 | 50410D 95

Page 96

D1260/D1260B | Owner's Manual | Appendix - System Trouble Displays

System Trouble Displays

Service AC Fail

If you see any of the system trouble displays shown below, contact your security company to determine whether repairs are needed.

The Silence> soft key is only displayed if a trouble tone is present. Press the Silence> soft key to silence the following trouble conditions.

Call for Service

Indicates that AC power to the security system is interrupted. Check the plug-in transformer and circuit breaker. Entering COMMAND 4 silences the trouble buzz. The display clears when AC power returns.

Service Missing Battery

Call your security company. Your security system may have failed (Your Security Co. will be replaced with the name of your security company).

Service Panel

Indicates the security system’s battery is disconnected or shorted.

Service Communication Fail

Indicates a problem with the panel. The panel is not operating (Your Security Co. will be replaced with the name of your security company). Call your security company for service.

Service Parameter

Indicates a problem with the panel. Your panel may not be operating properly (Your Alarm Company will be replaced with the name of your security company). Call your security company for service.

Service Low Battery

Indicates the security system’s battery is low, or temporarily draining faster than the system can charge it. If this display remains or appears frequently, call your security company for service.

Your security system makes repeated attempts to communicate with the security company.

In the event your security system fails to communicate, the command center buzzes and displays

Comm Fail Route Grp1

(Route Group number can

be from 1 to 4) Notify your security company of the communication

trouble.

Service Keypad

Indicates that a command center, other than the one displaying the message, is in a trouble condition. Notify your security company.

96 Bosch Security Systems | 9/04 | 50410D

Page 97

Service Phone Line #1 (or #2)

D1260/D1260B | Owner's Manual | Appendix - System Trouble Displays

24 Hour Point Bypass

Indicates telephone line trouble. Call your phone company from another phone to report telephone trouble. This message may not appear in some systems.

Service Printer

Printer number could also be 18 or 19

Indicates that a local printer (if installed) at your premises is in a trouble condition. Check to be sure the printer is powered on, the paper is correctly is inserted, and the printer is selected. Contact your security company if you have questions or the display doesn’t clear. You system may not include a local printer.

Service D9210

This display indicates that 24-hour points have been bypassed.

Indicates that one of the D9210 Access Control Modules (possible of 8 total) connected to the panel has encountered a problem. Contact your security company.

Service Point Bus 1 (or 2)

Displays when a problem has occurred with the panel’s Point Bus Wiring. Call your security company.

Fire Point Bypass

This display indicates that fire points have been bypassed.

Bosch Security Systems | 9/04 | 50410D 97

Page 98

D1260/D1260B | Owner's Manual | Appendix - Security System Glossary

Security System Glossary

Area

A group of detection devices

Exit Delay

connected to your security system.

Arm

To turn on your controlled points (burglar detection devices). When an area is armed and a controlled point trips, an alarm occurs or entry delay begins. When an area is disarmed,

Authority Level

faulting controlled points does not generate alarms.

Your security company or security representative assigns an authority

Faulted Point

Force Arm

level to your passcode. The authority level determines what command center functions you can execute.

Bypass

Selectively remove points from the

Idle Text

security system. You might bypass a point in order to arm the perimeter with a window open.

Central Station

A facility where trained personnel monitor your security system 24 hours

Master Arm

a day. Your security system may be programmed to contact the central

station during alarm conditions,

Closing Report

enabling central station personnel to dispatch the proper authorities.

A report your system can be programmed to send to the central

Opening Report

station indicating that an area has been armed. Opening and closing reports

Command Menu

are commonly used by commercial accounts.

A list of functions programmed by your security company. They can

Perimeter Arm

Point

perform most command center functions with only two or three keystrokes.

Entry Delay

A programmed delay of system alarm response, which allows you to enter an armed area through the correct point and disarm the area. If you don’t

Relay

disarm before the delay time expires, the system begins an alarm response, which may include reports to the central station.

A programmed delay of system alarm response, which allows you to exit after arming an area. If you don’t exit before the delay time expires, entry delay begins. You must disarm the system. If you don’t disarm before the delay time expires, the system begins an alarm response, which may include reports to the central station.

A point that is not normal (a door or window is open).

To turn on (arm) the security system even though one or more points are faulted. Force arming bypasses the faulted points.

The security system displays idle text at command centers when it is not performing a user-requested function. Idle text shows the arming status of the system.

To turn on (arm) both interior points and perimeter points.

A list of functions you execute from a command center.

A report your system can be programmed to send to the central station indicating that an area has been disarmed. Opening and closing reports are commonly used by commercial accounts.

An arming command that arms only the perimeter points.

A detection device or group of devices connected to your security system. Points display individually at the command center with custom text. The text can describe a single door, motion sensor, smoke detector, or an area such as UPSTAIRS or GARAGE.

Your system may have relays programmed to provide control of devices such as premises lighting or entry gates. Your security company programs relays for automatic control and/or control from your command center.

Trouble

A service condition that needs to be corrected, such as a broken wire

98 Bosch Security Systems | 9/04 | 50410D

Page 99

D1260/D1260B | Owner's Manual | Appendix - Maintenance and Service

Maintenance and Service

This security system requires very little maintenance, however, you should test the system weekly to ensure it is working properly. A test schedule and maintenance program can be arranged. If you notice a change in operation during normal use or testing, call for service as soon as possible. Do not attempt to repair the control panel, command centers, or detectors yourself.

How to Clean the Command Center

If your command center gets dirty, apply a household glass cleaner to a clean cloth or paper towel and wipe the surface. Do not spray any liquid directly onto the command center. It could run inside the case and damage electrical circuits.

Your Alarm Company

Name: Call This

Number Before Testing

Bosch Security Systems | 9/04 | 50410D 99

Page 100

Bosch Security Systems 130 Perinton Parkway Fairport, NY 14450-9199 Customer Service: (800) 289-0096 Technical Support: (888) 886-6189

Bosch D1260, D1260B User Manual 2

Specifications and Main Features

Frequently Asked Questions

User Manual