Bosch B36CT80SNS, B36CT81SNS Quick Guide

Quickstart Helpful Hints

Note:

For important safety instructions, information on installation, use and maintenance of the appliance, please refer to the entire user manual.

First steps

1. Remove information material,

adhesive tape and protective foil.

2. Remove the power cord and

the equipment package from the appliance.

3. Clean the appliance.

4. Roll appliance to its final location.

Aligning the appliance

1. Using a wrench, screw down both

height adjustable feet, so that they firmly touch the floor.

2. Adjust each separately, so that

the appliance is also aligned and straight.

3. Use a level to confirm.

Align the vertical gap between the doors

→ refer to "Installing the appliance"

in the user manual, page 8

Align the horizontal gap between the doors

→ refer to "Installing the appliance"

in the user manual, page 9

Setting cool-fresh compartment

→ refer to "Controls for cool-fresh compartment" in the user manual, page 16

1. Press any button on the cool-fresh compartment controls.

2. Press and hold the unlock button of the cool-fresh compartment

controls, until the light bar lights up completely.

3. Press your desired storage setting button.

Equipment Bar

 You can adjust the equipment bar vertically and move the

bin (hanging), shelf (hanging) and bottle shelf (hanging) sideways.

Connect your appliance

1. Download the

Home Connect (America) app.

2. Scan the

QR code.

3. Follow the

instruc tions in the app.

Installing the handles

(only applicable for appliances with handles)

1. Fit the handles vertically and

horizontally onto the pre-assembled bolts.

2. Use the included 2.5 mm

Allen wrench to tighten the pre-assembled screws clockwise in the handles.

Note:

The holes in the door handles face up and down (vertical handles) and the holes in the drawer handles only face down (horizontal handles).

Water and electrical connection

 Connect water supply on the rear

of the appliance.

 Insert the power cord plug on the

rear of the appliance and into an outlet.

Purge the water filter

1. Hold the glass under the

water dispenser.

2. Push the glass upwards against

the dispenser lever or press è button and dispense water for 5 minutes, approximately 3 gallons.

3. Press " button to switch on ice

cube production and discard ice cubes within the first 24 hours.

Cleaning your appliance

 Clean the appliance with a

soft cloth, lukewarm water and a little pH-neutral cleaning liquid.

Ethylene absorber installation

1. Install and activate the timer.

2. Insert both unopened sachets

into the inside housing holders.

3. Ax adhesive strip onto the

outside housing holder.

4. Place the Ethylene absorber

on the interior wall closest to the middle of the cool-fresh bin.

Lighting customization

Note:

Never use stainless steel

cleaners on the exterior of

the appliance.

Installing the equipment

 Install the loose equipment parts

as shown in the appliance overview picture.

→ refer to "Getting to know your applian

ce" in the user manual, page 14

1. Press menu button.

2. Press light settings button.

3. Press Y/X Settings button

repeatedly until the settings display shows the desired brightness level.

Note:

0 = lighting o 1 = minimum brightness 5 = maximum brightness

8001151558

(9904)

en-us

Quickstart Helpful Hints

Note:

For important safety instructions, information on installation, use and maintenance of the appliance, please refer to the entire user manual.

First steps

1. Remove information material,

adhesive tape and protective foil.

2. Remove the power cord and

the equipment package from the appliance.

3. Clean the appliance.

4. Roll appliance to its final location.

Aligning the appliance

1. Using a wrench, screw down both

height adjustable feet, so that they firmly touch the floor.

2. Adjust each separately, so that

the appliance is also aligned and straight.

3. Use a level to confirm.

Align the vertical gap between the doors

→ refer to "Installing the appliance"

in the user manual, page 8

Align the horizontal gap between the doors

→ refer to "Installing the appliance"

in the user manual, page 9

Setting cool-fresh compartment

→ refer to "Controls for cool-fresh compartment" in the user manual, page 16

1. Press any button on the cool-fresh compartment controls.

2. Press and hold the unlock button of the cool-fresh compartment

controls, until the light bar lights up completely.

3. Press your desired storage setting button.

Equipment Bar

 You can adjust the equipment bar vertically and move the

bin (hanging), shelf (hanging) and bottle shelf (hanging) sideways.

Connect your appliance

1. Download the

Home Connect (America) app.

2. Scan the

QR code.

3. Follow the

instruc tions in the app.

Installing the handles

(only applicable for appliances with handles)

1. Fit the handles vertically and

horizontally onto the pre-assembled bolts.

2. Use the included 2.5 mm

Allen wrench to tighten the pre-assembled screws clockwise in the handles.

Note:

The holes in the door handles face up and down (vertical handles) and the holes in the drawer handles only face down (horizontal handles).

Water and electrical connection

 Connect water supply on the rear

of the appliance.

 Insert the power cord plug on the

rear of the appliance and into an outlet.

Purge the water filter

1. Hold the glass under the

water dispenser.

2. Push the glass upwards against

the dispenser lever or press è button and dispense water for 5 minutes, approximately 3 gallons.

3. Press " button to switch on ice

cube production and discard ice cubes within the first 24 hours.

Cleaning your appliance

 Clean the appliance with a

soft cloth, lukewarm water and a little pH-neutral cleaning liquid.

Ethylene absorber installation

1. Install and activate the timer.

2. Insert both unopened sachets

into the inside housing holders.

3. Ax adhesive strip onto the

outside housing holder.

4. Place the Ethylene absorber

on the interior wall closest to the middle of the cool-fresh bin.

Lighting customization

Note:

Never use stainless steel

cleaners on the exterior of

the appliance.

Installing the equipment

 Install the loose equipment parts

as shown in the appliance overview picture.

→ refer to "Getting to know your applian

ce" in the user manual, page 14

1. Press menu button.

2. Press light settings button.

3. Press Y/X Settings button

repeatedly until the settings display shows the desired brightness level.

Note:

0 = lighting o 1 = minimum brightness 5 = maximum brightness