Bosch 3SE24M850EU User Manual
en
138
1,65
16
13
140
1,05
14
–
75
0,90
14
11
30
0,80
10
–
19
0,05
4
–
140
1,60
16
–
Brief and handy:
everything your dishwasher
needs...
Before using for the first
time, read the installation
and operating instructions!
Fill with special salt
Set the water softening system *
Find out the water hardness at your water utility
company and enter
* only before using the dish-
washer for the first time or
if the water hardness
changes
Dissolves limescale (not required for set value 0!)
Read off the setting ... and then set
ABC
Reset
Quickly sorted ...
– Hold down programme button B and switch on the main
switch, then release the buttons. The display of button B
and the number 4 set by the factory flash.
– Each time button B is depressed, the setting increases by
one; if 7 has been reached, the display jumps back to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
Summary of instructions for dishwasher
Switch on appliance
Press On/Off switch, running time of the
chosen programme appears
Switch off the appliance Everything O.K...
9000 167 295 8605
When the display shows 0 (end of programme),
press On/Off switch
Fill with rinse aid
Fill with detergent
Select programme
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
2 pt water into the
salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never detergent!)
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2.
Pour in
rinse aid.
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufacturer’s instructions.
Pour in
detergent.
Quick, economical or intensive ...
Programme overview
This overview lists the max. possible number of
programmes. The programmes supplied with your
appliance are indicated on the fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Additional programmes **
** on some models
h.
Duration in minutes
Electricity consumption in kWh
Water consumption in litres
with Aquasensor
Time selection
...switches on as soon as
you press the time
selection button:
Alters the programme
start in hourly steps
Increased flexibility ...
Upper basket cleaning
...Only the crockery in the
upper basket is cleaned
NormalIntensiveEcoQuick
Gentle
Screw on the
lid. Switch on
dishwasher
immediately.
Close the
lid. CLICK!
Push the lid
shut, press.
PLOP!
455070 65 40
Prerinse
Maintenance and care
Strainers ...
Check, if
required, clean
Rotate filter
cylinder, remove
filter system ...
For perfect rinsing results ...
rinse under
flowing water ...
Insert ... Screw in filter
system NOTE
MARK!
Cleaning the waste-water pump *
* With some models
– Ladle out water and remove filters
– Unscrew cover (Torx T20)
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Spray arms ...
Remove
blockages/deposits
Pull lower arm
upwards ...
Rectifying minor faults yourself ...
Fault Possible causes
Residual water
in the appliance
Appliance is not running /
stops
Check water supply
Display lights up
Plastic / utensils
discoloured
Waste water pump blocked
The programme has not yet ended
Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Too little detergent
Discoloration caused by food colourings
(tomato sauce)
Unscrew upper
arm ...
... as it is worth doing it yourself!
Remedial action
Clean waste-water pump (see above).
Close appliance and switch on.
or terminate programme (see
Terminating the programme).
Open supply fitting.
Install supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min. when
water supply is open.
If the flow rate is less, replace the
supply fitting.
Follow manufacturer’s instructions
(detergent).
Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
Clean spray nozzles
under flowing water
(perhaps with
toothpick) ...
Fault Possible causes Remedial
Utensils are not clean
Sand or gritty residue
on the utensils
Stains and streaks
Milky film on the utensils
(removable)
Milky film, glasses
cloudy / dull
(not removable)
Insert lower arm ...
Screw in upper arm
Utensils are situated close together
or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Rinse-aid dosage too high / too low
Water softening system incorrectly set;
No salt
Glasses not dishwasher-proof.
action
Separate the utensils, prevent contact
points.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Streaks: reduce dosage.
Water or limescale stains: increase
dosage.
Correctly set water softening system.
Refill with salt.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
Rust on the cutlery Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Use dishwasher-proof cutlery.
Never wash rusting parts
in the appliance.
More information can be found in the operating instructions
Stopping the programme ... Loading the dishwasher correctly ...
Press and hold the two
reset buttons simultaneously for
approximately 3 seconds while
the programme is running
(RESET)
”0” appears
The programme will stop
after 1 minute
Switch off the appliance.
Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,
large remnants of jam, dairy products and food) according to the operating instructions and check that
the spray arms can rotate freely.
Loading...