Bontrager Ion Pro RT, Ion 200 RT, Flare RT Users guide

trekbikes.com

PN 572345-3

Ion Pro RT Ion 200 RT Flare RT

About this manual

This manual is for Bontrager lights Ion Pro RT, Ion 200 RT (headlights) and Flare RT (tail light).

RT indicates light is rechargeable and remote controllable when paired with Bontrager Transmitr remote, PN 502865, or another ANT+ compatible device.

WARNING

Do not use if the battery is impacted. Also do not puncture, crush, deform, disassemble, or heat a lithium-ion battery above the permitted temperature. Inﬂicted damage to the battery may result in a ﬁre, explosion, or coming in contact with specks of lithium or lithium dust.

Please read all Warnings in this manual before using these lights.

Speciﬁcations

• Ion Pro RT: 4900mAh, 3.63V, 17.787Wh lithium-ion battery

• Ion 200RT and Flare RT: 420mAh, 3.7 Vdc,

1.6 Wh lithium polymer battery

• Battery charging and operating temperature: 32˚F to 113˚F (0˚C to 45˚C). Reduced performance when operating below freezing.

For more information

If you need help not offered by this manual, talk to your Bontrager retailer or visit trekbikes.com.

List of parts

You may have purchased one or more of the following lights.

Ion Pro RT Ion 200 RT Flare RT

Light

Mount

25.4 - 35.0mm Adjustable Bar Mount with shim PN W552375

Charging Cable

Fast Charge Micro USB Cable

PN W559136, (4-wire)

Front of bike

Quick Connect 0˚ Mounting Bracket

PN W527649

Quick Connect 16˚ Bracket for tail light

PN W533846

Mounts to the seatpost or a rack.

*Fits 22.2mm to 35mm bars.

Charger Cable PN W327765, (2-wire) Charger Cable PN W327765, (2-wire)

Basic operation (see Table 1)

To turn on, double click (Ion Pro RT) (similar to a computer mouse) and single click (Ion 200 RT / Flare RT) the power button. To turn off, press and hold the power button. To change mode, quick-press the power button.

NOTE: When turned on Ion Pro RT, Ion 200 RT and the Flare RT will return to the last active mode.

Table 1. Modes, runtimes, and battery life

Model Power Button/Status LED Mode

Ion Pro RT

Power / Status LED Button

High 1300 1.5

Max Output

(lumens)

Medium 800 3 Low 400 6 Red Steady 5 to 25% Night Flash 200 26 Day Flash 300 22

Ion 200 RT

Power Button Status LED

High 200 1.5 Medium 100 3 Low 5 14.5 Red Steady 5 to 25% Night Flash 5 30

Day Flash

Flare RT

Power Button Status LED

Day Flash All Day Flash

Night Flash 5 15 Red Steady 5 to 25% Day Steady

Night Steady 5 13.5

Supports auto brightness. 2Not including 30 minute low battery feature

Battery charging and care (see Table 2)

Although the light is charged at the factory, it is recommended to charge it before ﬁrst use.

To charge the battery

IMPORTANT: For best results, charge at room temperature in a dry place. Use

a quality CE or UL approved USB charger rated for 500 mA or greater. Avoid extreme conditions including wet, cold, or extremely hot.

1. Open the USB port cover.

2. Plug the Micro charger cable into the USB port on the light.

3. Plug the cable into a computer or wall adapter.

4. When the charge is complete, unplug the Micro charger cable and close the USB port cover.

IMPORTANT: Ensure the USB cover is latched before riding in rain or in wet conditions. If the USB cover is not closed, damage to the light may occur.

Ion Pro RT

Ion 200 RT

Flare RT

100 12

90 6 45 12

25 4.5

Table 2. Battery charging and care

Model

Ion Pro RT

Ion 200 RT

Flare RT

Flashes fast (2 Hz) with 4 wire USB cable and a 500mA charger, or slow

(1 Hz) with 2 wire USB cable

When fully charged, status led remains steady for 1 minute then turns off

Requires a 4 wire USB cable, supplied, and a 500mA charger

Runtime

(hours)

Power Button/

Status LED Color

Green Steady 25 to 100%

Red Flashing Less than 5%

Green Steady 25 to 100%

Red Flashing Less than 5%

Green Steady 25 to 100%

Red Flashing Less than 5%

Power Button/

Status LED

Color

Red Flash

Yellow Flash

Green Flash

Green Steady2 100%

Red Flash 0% - 75%

Green Flash 75% - 99%

Green Steady2 99% - 100%

Red Flash 0% - 75%

Green Flash 75% - 99%

Green Steady2 99% - 100%

Battery Life, %

Charge

Charge, %

Duration

(hours)

<25%

25% - 75% 7

75% - 99% 15

Accessories

(purchase separately)

Head Lights Tail Lights

Helmets (Blendr mount system) *Circuit Model 21764

Rally Model 21797

22.2-31.8mm Adjustable Bar Mount

PN W530421

Rack attachment

Use an 8mm M5 bolt and washer, PN 537061 with Quick Connect 16˚ bracket supplied, or with complete rack mount kit, PN 552376

Bontrager Helmet Bracket

PN 428462

Transmitr Remote

Model 502865

*Compatible with all

22.2-35.0mm Adjustable Sync Bracket

Model 418921

Bontrager Garmin Edge 1030 GPS Computer

Model 21831

Seat Pack Clips

Metal, PN 424905 Plastic, PN W528503

22.2

25.4

31.8

35.0

Bontrager RT lights.

Speed Concept Attachment

Take off the reﬂector mounting bracket, PN W327560 and replace the end with the Flare Round Mounting Kit interface, PN 418932

WARNING

The lights may be hot and could cause a burn or damage material it may contact. Do not activate (turn on) light in enclosed area. Avoid accidental wireless activation.

Caring for the battery

Store the light at room temperature in a dry place. Avoid moisture, or extreme hot or cold.

Store the light in the charged condition. Avoid ‘deep discharge’. Battery life will decrease if the battery is stored in a fully discharged condition.

Over time, the run time of the battery will diminish. Expect about 500 full charges, depending on care. After a full life, the battery will continue to charge but with a lower run time. When the run time is unsatisfactory, do not open the

case of the light or incinerate; please recycle.

Traveling with the battery

Li-ion batteries cannot be shipped by air due to airline regulations. When traveling by air, place the light in your carry-on.

Recycling

Please recycle the battery. In the US, you can ﬁnd out

where to do this at www.call2recycle.org This symbol on the product(s) and / or accompanying

documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, outside the US, please take this product(s) to designated collection points. Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Ion Pro RT information, installation, and special features

Installation

1. Loosen knob and open.

2. Adjust for bar size (31.8mm or 35mm).

3. Close and tighten knob.

4. Slide light onto mount until it locks in place. NOTE: Use provided shim to ﬁt 25.4 bars.

Removal

5. Press down.

6. Slide light to remove.

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the output brightness to 50 lumens. This extends the light output for an additional 30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button 8 seconds to select it. The light will turn off and the main LED will ﬂash once. To unlock, repeat the process.

Reset

To reset the light to factory default settings, with the light on, press and hold the power button for 15 seconds. The main LED will ﬂash once at 8 seconds, and again at 15 seconds. Release the button after the second ﬂash.

Wireless Communication

The light is shipped with ANT+ and Bluetooth wireless connectivity enabled. To disable, with the light off, press and hold the power button for 15 seconds. The main LED will ﬂash once at 8 seconds, and again at 15 seconds. Release the button after the second ﬂash.

NOTE: The status LED turns on blue for 3 seconds IF the wireless is enabled. After 3 seconds, the status LED continues to display the battery level. If the

31.8mm 35mm

wireless is disabled, the status LED immediately displays the battery level.

Pairing to the Transmitr Remote, Bontrager Garmin Edge® GPS computer or select Garmin Edge® computers

The Transmitr Remote (or select Garmin Edge computers, sold separately) allows remote control of the light. This feature is only available on the Ion Pro RT, Ion 200 RT, and the Flare RT as well as other compatible Transmitr lights.

For more complete instructions, refer to the Transmitr manual at trekbikes.com. For Garmin related instruction and a complete listing of compatible Edge devices visit support: garmin.com.

Before starting, place the remote and all lights within a small area. Move 15 feet from other Transmitr / ANT+ compatible lights to prevent unintentional pairing. If a light is unintentionally paired, restart the pairing process at the beginning.

NOTE: All pairings must be done in a single session. After pairing is ﬁnished, pairing any additional lights will require that you repeat the entire pairing procedure.

1. Place the light close to the Transmitr Remote (within 15cm / 6in).

2. Quick-press the power button on the light to turn it on, then quick-press to turn it off again.

NOTE: After completing this step, do not press the power button on the light again until pairing is complete.

3. Press-and-hold the center button on the Transmitr Remote for at least 8 seconds. When the corner buttons ﬂash, release the center button.

4. While the remote searches for a light, its center button ﬂashes red. When the Transmitr Remote ﬁnds a light, the center button on the remote will change from red to green, and the found light will ﬂash.

5. While the found light is still ﬂashing, quick-press the button on the Transmitr Remote to which you would like to pair the light. The selected button will glow, and the found (paired) light will stop ﬂashing and turn off.

NOTE: After the pairing, the center button on the remote will ﬂash red until the Transmitr Remote ﬁnds another available light.

6. Repeat Step 4 and Step 5 for each additional light to be paired.

To exit pairing

1. When all lights are paired, quick-press the center button on the remote. The button will stop ﬂashing and turn off.

To verify pairing

1. Quick-press the center button on the remote to turn on all paired lights.

2. Press-and-hold the center button to turn off all of them.

3. Turn on each light individually. Quick-press each paired corner button on the remote to turn on the individual light(s).

4. Press-and-hold the same corner button to turn off the light.

Using the Transmitr Remote

To turn on all lights

ON: Quick-press the center button. OFF: Press and hold the center button.

To turn on an individual light

ON: Quick-press the corner button that controls the light. OFF: Press and hold the same button.

To change modes of an individual light

Each quick-press of a button that controls a light will cycle through the modes.

To see battery power status on the remote

When a corner button is pressed, the center button will show the battery status of the light.

Center Button Color Battery Life, %

Flashing red Less than 5

Red Between 5 and 25

Green More than 25

Ion 200 RT information, installation, and special features

Installation

To attach with the Quick Connect 0˚ offset bracket

1. Place the quick connect on the handlebar with the hook in front.

2. Stretch the strap under the bar and connect to the hook. NOTE: Use the second hook to latch excess strap.

3. Slide the Ion 200 RT onto the bracket until it clicks. The power button should be facing up and the lens of the light should be perpendicular to the road.

Removal

Press down on the tab and slide the light away from the lever.

Alternatively, you can remove the entire quick-connect bracket, with the light attached.

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the output brightness to 5 lumens. This extends the light output for an additional 30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button 8 seconds to select it. The light will turn off and the main LED will ﬂash once. To unlock, repeat the process.

Auto brightness

The light is shipped with an ambient light sensor disabled. When the ambient light sensor is enabled, the light automatically changes modes with ambient light conditions. It changes from Day Flash to High Steady. To enable, press and hold the power button 8 seconds. The light will ﬂash once.

NOTE: When auto brightness is enabled, all modes are manually accessible.

Reset

Wireless Communication

NOTE: The status LED turns on blue for 3 seconds IF the wireless is enabled. After 3 seconds, the status LED continues to display the battery level. If the wireless is disabled, the status LED immediately displays the battery level.

Front of bike

2. Remove

1. Press

Flare RT information, installation, and special features

Installation

To attach with the Quick Connect 16˚ offset bracket

IMPORTANT: The seatpost/saddle icon shows that the lens is oriented perpendicular to the ground to optimize visibility.

NOTE: Use the second hook to latch any excess strap.

To attach to a seat pack

Attach the seat pack clip to the bag loop. To optimize visibility, ensure the light lens is oriented perpendicular to the ground.

To attach to a rack

Remove the quick connect clip from the rubber strap and attach to a rack with a M5 bolt and washer, sold separately, PN 537061.

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the output brightness and begins to ﬂash. This extends the light output for an additional 30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button 8 seconds to select it. The light will turn off and the main LED will ﬂash once. To unlock, repeat the process.

Auto brightness

The light is shipped with an ambient light sensor disabled. When the ambient light sensor is enabled, the light automatically changes modes with ambient light conditions. It changes from Day Flash or All Day Flash to Night Flash, OR Day Steady to Night Steady. To enable, press and hold the power button 8 seconds. The light will ﬂash once.

NOTE: When auto brightness is enabled, Day Flash, All Day Flash and Day Steady are manually accessible.

Reset

Wireless Communication

WARNING

A bicycle without correct lights and reﬂectors might be difﬁcult for other people to see, and you might not be able to see. If you cannot see, or other people cannot see you, you could have an accident. Make sure your lights operate correctly and that batteries are charged.

Trek Bicycle Corporation contact information:

North America

Trek Bicycle Corporation 801 West Madison Street Waterloo, WI 53594 USA Tel: 800-313-8735

Europe

Bikeurope BV Ceintuurbaan 2-20C 3847 LG Harderwijk The Netherlands Tel: +31 (0)88 4500699

Australia

Trek Bicycle Corp. Au. 8 Townsville Street (Level One) Fyshwick (ACT) 2609 AU Tel: +61 (02) 61 732 400

Statements of Regulatory Compliance

FCC Compliance

Ion Pro RT FCC ID: 2AHXD552373 Ion 200 RT/Flare RT FCC ID: 2AHXD553852

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

— Consult the dealer or experienced radio / TV technician for help.

NOTES: TREK BICYCLE CORPORATION IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY TREK BICYCLE CORPORATION OF THIS DEVICE COULD VOID THE USER’S AUTHORITY TO OPERATE THE DEVICE.

Industry Canada Compliance

Ion Pro RT (P/N 552373) IC ID: 21334-552373 Ion 200 RT (P/N 553853) IC ID: 21334-553852 Flare RT (P/N 553852) IC ID: 21334-553852

CAN ICES-3(B)/NMB-3(B) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Leprésent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils radio. Exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilsateur de l’appareil doit accepter tout brouillage radioélectrque subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.

This Ion Pro RT lighting equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The radiated output power of the Ion Pro RT Wireless Device is below the Industry Canada (IC) radio frequency exposure limits, when used as directed in this manual (Note: attaching this light to a helmet changes the absorption characteristics of the light-body system). This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/ nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Cet appareil est conforme aux limites d’exposition à la fréquence radio (FR) d’IC et de FCC. La puissance de sortie émise par l’appareil de sans ﬁl Ion Pro RT est inférieure à la limite d’exposition aux fréquences radio d’Industry Canada (IC). Cet appareil est en contact direct avec l’utilisateur dans des conditions normales d’utilisation. L’émetteur ne doit pas être co-implémenté ou utilisé conjointement avec une autre antenne ou un autre émetteur. Ce périphérique est homologué pour l’utilisation au Canada. Pour consulter l’entrée correspondant à l’appareil dans la liste d’équipement radio (REL Radio Equipment List)d’Industry Canada rendez-vous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch. do?lang=fra

Pour des informations supplémentaires concernant l’exposition aux RF au Canada rendezvous sur: http://www.ic.gc.ca/eic/site/smt-gst.nsf/fra/sf08792.html

European Union Compliance

Ion Pro RT and Ion 200 RT do not comply with German StVZO regulations! Trek Bicycle Corporation and Bontrager hereby declare that the wireless device

identiﬁed as ‘Ion Pro RT’, ‘Ion 200 RT’ and ‘Flare RT’ are in compliance with the following European Directives:

• Radio Equipment Directive 2014/53/EU (Ion Pro RT only)

• EMC Directive 2014/30/EU

• Low Voltage Directive 2014/35/EU (Ion Pro RT only

• RoHS Directive 2011/65/EU The full text of the EU declaration of conformity is available from your dealer, or

at the following internet address: http://www.trekbikes.com/support

If you wish to see this manual in another language, please visit trekbikes.com/manuals and look for the Ion Pro RT/Ion 200 RT/Flare RT manual on the Manuals and user guides page.

DE Wenn Sie dieses Handbuch in einer anderen Sprache sehen möchten,

besuchen Sie bitte www.trekbikes.com/support und suchen Sie nach dem Handbuch Ion Pro RT / Ion 200 RT / Flare RT auf der Seite Handbücher und Benutzerhandbücher.

FR Si vous souhaitez voir ce manuel dans une autre langue, rendez-vous sur

www.trekbikes.com/support et recherchez le manuel Ion Pro RT / Ion 200 RT / Flare RT sur la page Manuels et guides de l’utilisateur.

ES Si desea ver este manual en otro idioma, visite www.trekbikes.com/support

y busque el manual Ion Pro RT / Ion 200 RT / Flare RT en la página Manuales y guías del usuario.

IT Se si desidera vedere questo manuale in un’altra lingua, visitare

www.trekbikes.com/support e cercare il manuale Ion Pro RT / Ion 200 RT / Flare RT nella pagina Manuali e manuali dell’utente.

PL Jeśli chcesz zobaczyć tę instrukcję w innym języku, odwiedź stronę

www.trekbikes.com/support i poszukaj instrukcji Ion Pro RT / Ion 200 RT / Flare RT na stronie Podręczniki i instrukcje obsługi.

PT Se você deseja ver este manual em outro idioma, visite

www.trekbikes.com/support e procure o manual do Ion Pro RT / Íon 200 RT / Flare RT na página Manuais e guias do usuário.

NL Als u deze handleiding in een andere taal wilt bekijken, gaat u naar

www.trekbikes.com/support en zoekt u naar de Ion Pro RT / Ion 200 RT / Flare RT-handleiding op de pagina Handleidingen en gebruikershandleidingen.

JA このマニュアルを別の言語で表示したい場合は、www.trekbikes.com/

supportにアクセスして、マニュアルおよびユーザーガイドページのIon Pro RT / Ion 200 RT / Flare RTマニュアルを参照してください。

KO 󼓣󾖴󻝓󺿣󼌫󼒳󾖴󻁓󻛧󾖴󼌧󼌣󻗋󻩣󺩏󾖴󼁥󻁓󻟣󻛫

󻦘󻢧󽋇󼍛󾖴󻝓󺿣󼌫󾖴󻥾󾖴󻸛󼐘󼓿󾖴󼊷󺸣󻺋󾖴󽄇󼓣󼜯󼌿󻺋 󻝓󺿣󼌫󼒳󾖴󼦭󼒫󼁜󼁋󼎓

ZH 如果您希望以其他语言查看本手册，请访问www.trekbikes.com/support，

并在手册和用户指南页面上查找Ion Pro RT / Ion 200 RT / Flare RT手册。

إذا كنت ترغب في مشاهدة هذا الدليل بلغة أخرى ، يرجى زيارة www.trekbikes.com/support وابحث عن Ion Pro RT / Ion 200 RT / Flare RT دليل على صفحة الأدلة وكتيبات المستخدم.

Bontrager Ion Pro RT, Ion 200 RT, Flare RT Users guide

Specifications and Main Features

Frequently Asked Questions

User Manual