Page 1
Mobile Nav
igation
TravelPilot Lucca 3.4
Operating instructions
(Long version)
Page 2
Device overview
Device overview
3
1
2
2
Page 3
The following buttons are located
beside the display:
1 On/Off switch:
Long press (longer than 3 sec-
•
onds): Switches the device
on/off.
Short press: Switches the
•
screen on/off. (Energy-saving
mode)
2 MENU:
Long press (longer than 3 sec-
•
onds): Opens the main menu of
the device.
Short press: Opens the quick
•
settings menu.
3 3.5" LCD touchscreen:
All entries and the control of
Lucca are carried out in a simple
and intuitive way by touching the
buttons displayed on the touchscreen.
Device overview
4
5
6
4 Headphone jack
5 SD/MMC card slot
6 Power connection
3
Page 4
Device overview
9
7
The underside features the following
controls:
7 USB connection
8 Connects the Lucca with the
suction cup holder
4
8
The rear side of the device features
the following element:
9 TMC antenna connection
Page 5
Contents
Device overview .......................2
About these instructions .......10
Safety notes ...........................10
Safety notes for navigation ...........10
Safety notes for handling
the Lucca ...................................... 11
Initial startup of Lucca ..........12
Lucca scope of delivery ................ 12
Protective screen fi lm ................... 13
Switching on the Lucca ................13
Setting the language ..................... 13
Charging the battery ..............14
Installation in the vehicle ......15
Attaching the suction cup
holder ........................................ 15
Removing the suction cup
holder ........................................ 15
Installing Lucca in the suction
cup holder ................................. 16
Removing the Lucca ................... 16
Switching on/off ....................16
Switching on .............................. 16
Activating the idle state ............. 16
Switching off ............................. 16
The menu button ....................17
Quick settings ............................ 17
The INFO button ........................ 17
Additional functions ................... 17
Operating the navigation
menus .....................................18
Software keyboard ........................ 18
Entering blank spaces ................ 18
Deleting characters .................... 18
Entering numbers, umlauts
and letters..................................18
List ................................................ 19
Buttons ......................................... 20
Information ................................... 21
Traffi c reports ............................ 21
GPS status .................................22
5
Page 6
Contents
Navigation ..............................23
General notes about
the navigation ............................... 23
Starting the navigation .................24
Entering a destination ................ 24
Navigating home ........................ 24
Showing a map .......................... 24
Traffi c reports (TMC) ................. 24
Settings...................................... 25
Exiting the menu ....................... 25
Additional functions ................... 25
GPS Info ..................................... 25
Route planning ........................... 25
Select map ................................. 25
Performing basic settings .............25
Setting the time zone ............... 26
Entering the home address ........ 26
Entering a destination................... 27
Entering a destination ................ 27
Entering the destination country .. 27
Entering a destination address ..29
Additional functions .................. 30
Selecting a point of interest ......... 30
Point of interest in the current
vicinity ....................................... 30
6
Additional functions .................. 32
Point of interest at a specifi c
location ...................................... 33
Special national destination ...... 35
Copying a destination from
the map......................................... 36
Moving the map section ............. 37
Copying the destination from
the favourites ................................ 39
Copying a favourite for
destination guidance .................39
Additional functions .................. 39
Copying one of the last
destinations .................................. 40
Additional functions .................. 41
Using the home address as
destination .................................... 41
Managing destinations ..........42
Saving destinations....................... 42
Saving one of the last
destinations ............................... 43
Renaming a destination ............. 43
Deleting a destination ................ 44
Deleting the complete list
with destinations ....................... 44
Page 7
Contents
Route planning with stages ...45
Planning a route ............................ 45
Editing a route .............................. 46
Changing the order of
route points ............................... 46
Deleting a route point ................ 46
Deleting a complete route list .... 47
Saving a route ............................... 47
Loading a route ............................. 47
Calculating a route ........................ 47
Starting the destination guidance
(GPS reception required) .......... 47
Calculating the route
without GPS reception .............. 47
Showing the route on the map .. 48
Travelling the route (simulation) .. 48
Specifying routing options ....49
TMC function .........................50
Connecting the TMC antenna ....... 50
Switching on the TMC function .... 51
Adjusting TMC options ................. 51
Showing traffi c reports ................. 51
Destination guidance .............52
Disturbed GPS reception ........... 53
Quitting the destination
guidance .................................... 53
Reaching the place of
destination ................................. 53
Working with the map ...........54
Map operation ..............................54
Showing a map .......................... 54
Touching the map ...................... 54
Buttons ......................................... 54
In map view without GPS
reception ................................... 55
In map view with GPS reception .. 55
Additional functions ................... 56
Day/night mode ......................... 57
Mute ........................................... 57
Settings...................................... 57
7
Page 8
Contents
Map display during
destination guidance ...............58
Navigation tools ............................ 58
Route information ......................... 59
Signpost information (exit signs) .. 59
Speed limit ...................................60
Activating additional map
information ................................... 60
Map information ........................60
Route information ...................... 61
Signpost information
(exit signs) ................................. 61
Speed limit ................................ 62
Additional functions during
the destination guidance ......... 63
Inserting an interim destination ... 63
Approaching the next destination .. 64
Blocking route segments .......64
Manual blocking ......................... 64
Unblocking ................................. 65
8
Basic settings of the Lucca ....65
Settings ........................................ 65
Language ................................... 66
Home address ............................ 66
Map information ........................67
Route information ...................... 67
Routing options .........................67
Route planning ........................... 67
TMC (traffi c information
data channel) ............................. 68
Signpost information ................. 68
Speed limit ................................ 68
Auto mode .................................69
Time zone ..................................70
Format ....................................... 70
Display ....................................... 70
Factory settings ......................... 71
Touchscreen ............................... 71
Product information ................... 71
Page 9
Contents
GPS mode of operation .........71
Using the SD/MMC card ........72
Preparation ................................... 72
Inserting the SD/MMC card ..........73
Removing the SD/MMC card......... 73
MP3 player .............................73
Starting the MP3 player ................ 73
Operating the MP3 player ............. 74
MP3 list ...................................... 74
Picture Viewer .......................75
Starting the Picture Viewer........... 75
Operating the Picture Viewer .......76
Slide show ................................. 76
Full-screen mode ....................... 77
Installing the map material ....77
Saving map material on
the SD/MMC card ......................... 77
Using map material with
the Lucca ...................................... 78
Removing the SD/MMC card......... 78
Updating the software
of the Lucca ...........................79
Technical data ........................79
Disposal of old unit ...............80
Service ...................................81
Warranty ................................81
Frequently asked questions /
FAQ .........................................82
9
Page 10
About these instructions Safety notes
About these instructions
The menus and buttons used in illustrations feature the English language.
In order to make these instructions
more comprehensible, the devicerelated terms in the text are listed
in the respective offi cial language –
with the exception of English – and in
parentheses behind the English term,
e.g. Quick Settings menu.
10
Safety notes
For your personal benefi t, carefully
read the following safety notes and
warnings before operating your Lucca for the fi rst time.
Safety notes for navigation
Caution:
Do not operate the Lucca while driving to protect yourself and others
against accidents!
View the display only if you are in a
safe travel situation!
The street routing and traffi c signs
have priority over the instructions of
the navigation system.
Follow the instruction of the Lucca
only if circumstances and traffi c regulations allow! Lucca will bring you to
your destination even if you have to
deviate from the planned route.
Page 11
Safety notes
Notes:
Routes are best planned before
•
starting your trip. If you want to
enter a new route while on the
road, please head for the next
parking or rest area!
If you did not understand the
•
voice information or if you
are not sure what to do at
the next intersection, use the
map or arrow display for quick
orientation.
Safety notes for handling
the Lucca
Caution:
Protect the device against moisture
since it is not waterproof and not
splashproof.
Notes:
•
Remove the power supply
connector of the Lucca if you
switch off the engine since the
GPS receiver constantly uses
electricity and could discharge
the vehicle battery.
Do not unplug the connector
•
by pulling on the wire. The wire
could be damaged!
Do not use harsh solvents to
•
clean the device; use only a
damp, lint-free cloth.
11
Page 12
Initial startup
Initial startup of Lucca
When you switch on the Lucca for
the fi rst time, a dialogue appears and
asks which language the Lucca should
use. (For further details, please read
the section "Setting the language"
in this chapter.) Wait a few minutes
after this setting until the navigation
application is operational.
Note:
Upon purchasing the Lucca, the
battery maybe empty. Please
charge the battery before using
the device.
12
Lucca scope of delivery
The scope of delivery contains the
following components:
Lucca
•
Suction cup holder
•
Charger cable for cigarette lighter
•
Antenna for TMC reception
•
Operating instructions
•
(short version)
CD/DVD with Europe road maps
•
and operating instructions
(long versions)
Optional accessories:
Carrying case
•
Battery charger for 110 to 230 V
•
USB cable
•
Second car set
•
Van/SUV suction cup holder
•
Bracket for ventilation opening
•
Page 13
A
Initial startup
Protective screen fi lm
Prior to the initial use, remove the
protective fi lm from the screen.
Switching on the Lucca
The On/Off switch is used to switch
the Lucca on or off. In its delivery
state, the Lucca is switched off.
➜
Briefl y press the On/Off switch in
the lower left corner of the Lucca.
A
The start screen of the Lucca appears.
Setting the language
The Lucca uses US English as the
standard language for the menus
and voice output. When you switch
on the Lucca for the fi rst time, a dialogue menu appears in which you can
select another language:
Select your preferred language in
➜
the dialogue menu.
Please follow the instructions.
➜
The language is loaded and the
main menu is displayed again.
13
Page 14
Charging the battery
Charging the battery
The rechargeable battery allows for
operating the Lucca without the external power supply.
If you started the navigation mode,
MP3 player or Picture Viewer, the top
center part of the screen shows the
charge indicator of the battery. The
symbols have the following meaning:
–
: The device is supplied by
an external power source. The
battery is fully charged.
–
: The device is supplied by
an external power source. The
battery is being charged.
–
: The device is supplied by
its internal battery. The charge
state of the battery is suffi cient.
–
: The device is supplied by
its internal battery. The charge
state of the battery is low.
The number of dark block segments on
the battery indicates the charge state
of the battery (0 to 3 segments).
14
Note:
If the charge state of the battery
is very low, a warning message is
displayed.
➜
To charge the battery, use the supplied charger cable for the cigarette lighter or an optional battery
charger.
Notes:
Use only a charger approved by
•
Blaupunkt. Please contact your
specialised Blaupunkt dealer.
Do not discard any batteries
•
in the household trash;
instead, return them to the
corresponding collection sites.
Page 15
Installation in the
vehicle
For temporary installation in a vehicle, the Lucca features a suction cup
holder to attach it to the windshield.
Caution:
Install the Lucca so that it does not
block your view and does not distract
from the traffi c.
Do not install the Lucca in the airbag
deployment area.
Ensure that the Lucca does not pose
a threat to passengers in the vehicle
in case of emergency braking.
Attaching the suction cup holder
The Lucca can be installed in the vehicle in a simple and safe way using
the supplied suction cup.
➜
Locate a suitable place for installing the Lucca.
To ensure a perfect hold, the glass
➜
must be free of dust and oil. If necessary, clean the glass fi rst.
Installation in the vehicle
Press the suction plate of the suc-
➜
tion cup against the windshield.
Push the lever on the suction cup
➜
towards the glass.
The track for mounting the Lucca
➜
must be aligned vertically.
Removing the suction cup holder
If you change vehicles, you can simply
remove the suction cup holder.
Push the lever on the suction cup
➜
away from the glass.
Carefully loosen the suction cup at
➜
the edge from the glass so that air
can enter between suction plate
and glass.
Carefully pull the suction cup off
➜
of the glass.
15
Page 16
p
Installation in the vehicle Switching on/off
Installing Lucca in the suction cup
holder
The suction cup holder features a
track for mounting the Lucca on the
inside.
Carefully push the guide of the
➜
Lucca over the track of the suction
cup holder.
p
Removing the Lucca
Pull the Lucca up and out of the
➜
suction cup holder.
16
Switching on/off
Switching on
Briefl y press the On/Off switch.
➜
The device switches on and displays the start screen.
Activating the idle state
Briefl y press the On/Off switch.
➜
The Lucca switches to the idle
state (screen off state).
Switching off
Press and hold the On/Off switch
➜
for longer than 3 seconds.
The Lucca is switched off.
Note:
The Lucca continues to require a
small amount of energy even if it is
switched off. If you use the Lucca
again after an extended period of
time, it may be necessary to recharge the battery.
Page 17
The menu button
The menu button
Quick settings
In the Quick Settings menu volume
and brightness can be adjusted. The
Quick Settings menu can be called at
any time, regardless of the currently
active menu.
➜
Press the MENU button.
The Quick Settings menu is dis-
played.
➜
Touch the
volume or brightness.
➜
to the previous menu.
Note:
After 5 seconds without touching
the display Lucca returns automatically to the previous menu.
/ buttons to adjust
: Touch this button to return
The INFO button
Prerequisite:
A destination guidance is active.
•
Touch the Info button in the Quick
➜
Settings menu.
The last voice instruction is re-
peated.
Additional functions
Touch the More button in the
➜
Quick Settings menu to call up the
additional functions.
Information
•
Touch the Information button.
–
The product information is dis-
played.
Battery
•
Touch the Battery button.
–
The status of the battery is dis-
played:
17
Page 18
The menu button Operating the navigation menus
Power Saving
•
Touch the Power Saving button.
–
The Power Saving menu is dis-
played.
Backlight Time Out: Touch the
–
setting under this menu item to
set the time until the backlight
will be switched off after the
last operation (save energy!).
Press the OK button to confi rm.
Battery Warning Time Out:
–
Touch the setting under this
menu item to adjust the time
for the battery warning. The
battery warning will be displayed accordingly before the
battery runs out. Touch the OK
button to confi rm.
Operating the
navigation menus
Software keyboard
If text entries are required, the touchscreen displays a software keyboard.
You can perform all entries using your
fi nger. Only capital letters can be entered.
You do not have to enter any special
characters or umlauts when entering
city or street names. The Lucca completes these characters automatically.
Entering blank spaces
To enter a blank space, touch the
➜
button.
Deleting characters
➜
To delete the last character, touch
button.
the
Entering numbers, umlauts and
letters
You can switch the software keyboard
so that you can enter numbers and
umlauts in addition to letters.
18
Page 19
Operating the navigation menus
To enter numbers, such as a postal
code,
touch the
➜
To return to the character entry mode,
touch the
➜
To enter an umlaut,
touch the
➜
The umlaut keyboard is displayed.
As soon as you enter an umlaut,
the character keyboard is automatically displayed again.
Note:
Umlauts do not have to be entered
when entering address information, but they may be helpful for
the description of stored destinations and routes.
button
button.
button
List
In many cases, you can display lists
from which you can select an entry.
This is the case, for example, if you
do not enter the complete name of a
place during the entry. After every entry of a letter, the text fi eld shows the
fi rst entry that starts with the previously entered characters. To display a
list with additional matching entries,
touch the List button.
The end of the list features entries what
contain the sequence of previously entered characters not at the beginning,
but in the middle or at the end.
One entry of the list is always selected.
The selected entry can be selected
➜
by touching the OK button.
These lists contain the following buttons:
➜
➜
: Touch the OK button to accept the selected entry. However,
you can also directly touch an entry to accept it.
: Touch this button to scroll
up in the list by one page (5 elements).
19
Page 20
Operating the navigation menus
➜
: Touch this button to scroll
down in the list by one page
(5 elements).
➜
To scroll in the list by several pages, touch the arrow symbols several times.
Note:
If the list features more than 5 elements, the scroll bar indicates the
current position in the list.
➜
: Touch this button to return
to the entry without selecting a
list element.
Buttons
These buttons are located on all menus of the Lucca:
➜
➜
: Touch this button to return
to the previously opened menu.
If you are in the Navigation menu,
you reach the main menu where
you can start another application,
such as the MP3 player or the Picture Viewer.
More: Touch this button to obtain
access to additional functions. Depending on the menu in which this
button is located, different functions are offered.
If this button is deactivated, no additional functions are available.
20
Page 21
Information
From the Navigation menu, you can
display the current traffi c reports and
the GPS status at any time.
Traffi c reports
Your Lucca is supplied with traffi c
reports via TMC (traffi c information
data channel). It considers the current traffi c situation and allows calculating dynamic routes. The traffi c
reports received can also be shown
on the display.
➜
In the Navigation menu, touch the
TMC button.
The TMC menu is displayed.
Operating the navigation menus
Touch the arrow symbols to change
➜
between traffi c reports.
Every report contains the name of
the concerned street and the type
of traffi c obstruction.
Touch the Update display button
➜
to update the traffi c reports.
Touch the button to close the
➜
menu.
Note:
If no TMC reception is currently
available, the Lucca automatically
searches for TMC signals.
21
Page 22
Operating the navigation menus
GPS status
The GPS status menu contains informa-
tion about your current position and
your current speed. In addition, you
can also save your current position.
➜
In the Navigation menu, touch the
More button.
The following window displays:
Touch the GPS Info button.
➜
The GPS Status menu is displayed.
GMT – Greenwich Mean Time:
•
West European Time without
daylight savings time.
Longitude/Latitude: Current
•
position. Entry of the eastern
longitude and northern latitude
Altitude: Current height above
•
mean sea level.
Direction: Current travel direc-
•
tion while moving.
Satellites: Number of satellites
•
received. The positioning requires
signals from at least three satellites. Only then is a destination
guidance possible.
22
Page 23
Operating the navigation menus Navigation
•
HDOP – Horizontal Dilution of
Precision: Indicates the qual-
ity of the positioning. In theory,
values from 0 to 50 are possible,
The following applies: The lower
the value, the more precise the
positioning (value 0 = no deviation from the actual position).
Values up to 8 are acceptable for
a destination guidance.
•
Speed: Indicates the current
speed of the vehicle.
•
Current position: Address of the
current location (if available).
➜
Save current position: Touch this
button to save the current position
to the favourites. This requires a
suffi cient GPS reception (at least
3 satellites).
➜
Touch the
GPS window.
button to close the
Navigation
General notes about the
navigation
The use of the Lucca is at your own
risk.
Caution:
Do not operate the Lucca while driving to protect yourself and others
against accidents!
View the display only if you are in a
safe travel situation!
The street routing and traffi c signs
have priority over the instructions of
the navigation system.
Follow the instruction of the Lucca
only if circumstances and traffi c regulations allow! Lucca will bring you to
your destination even if you have to
deviate from the planned route.
23
Page 24
Navigation
Starting the navigation
Switch on the device with the On/
➜
Off switch.
In the main menu, touch the Navi-
➜
gation button.
The Navigation menu is displayed.
24
The Navigation menu allows access to
all the functions of the navigation.
Entering a destination
Touch the Destination entry but-
➜
ton to enter a destination for the
destination guidance.
For further details, please read the
section "Entering a destination".
Navigating home
Touch the Home button to use
➜
your stored home address as the
destination for the destination
guidance.
For further details, read the section
"Using the home address as destination".
Showing a map
Touch the Show map button to
➜
display the loaded street map.
For further details, read the section
"Working with the map".
Traffi c reports (TMC)
Touch the TMC button to obtain an
➜
overview of the current traffi c reports received by our Lucca.
Page 25
Navigation
Settings
Touch the Settings button to ad-
➜
just the settings of your Lucca.
For further details, read the section
"Performing basic settings".
Exiting the menu
In the Navigation menu, touch
➜
Additional functions
➜
The list of additional functions displays.
to quit the navigation.
You are returned to the main
menu.
Touch the More button to obtain
access to additional functions of
the navigation.
GPS Info
➜
Touch the GPS Info button to obtain information about the current
GPS status and about your current
position.
Route planning
➜
Touch the Itinerary button to plan
a route with several stages.
For further details, read the section
"Route planning with stages".
Select map
➜
Touch the Select Map button to
choose one of the available road
maps.
Performing basic settings
Before you start a destination guidance,
you should set the time zone of
•
your position so that the correct
arrival times are displayed during
the destination guidance and
you should enter your home ad-
•
dress to quickly navigate home
from any location.
25
Page 26
Navigation
Setting the time zone
➜
In the Navigation menu, touch the
Settings button.
The Settings menu displays.
Touch the
➜
til the Time zone button appears.
Next, touch Time zone.
➜
The Time zone menu is displayed.
Touch Time zone to open the list
➜
of possible Settings.
Touch the time zone in the list that
➜
applies to your current location.
(For the West European Time,
select "(GMT) Greenwich Mean
Time").
The time zone is set, and you are
returned to the Time zone menu.
26
button repeatedly un-
Note:
The selection is facilitated by the
display of the capitols in the respective time zone.
➜
If daylight savings time currently
applies to your position, touch the
Daylight saving time button.
The button displays a check mark.
Note:
If the time is changed at your position or if you drive into a different time zone, you must adjust the
corresponding settings.
Touch the OK button.
➜
The Navigation menu is displayed.
Entering the home address
In the Navigation menu, touch the
➜
Settings button.
The Settings menu displays.
Repeatedly touch the
➜
until the Home address button appears.
➜
Touch the Home address button.
The Home address menu is dis-
played.
buttons
Page 27
Touch the Enter your home ad-
➜
dress button.
The Destination entry menu is dis-
played.
Touch the Address button and en-
➜
ter your home address. (see "Entering a destination address")
Touch the Set as home address
➜
button.
The address is copied into the
Home address menu.
Touch the OK button.
➜
The Navigation menu is displayed
again.
Navigation
Entering a destination
This section contains information
about the different methods for entering, selecting and managing destinations with the Lucca.
The chapter "Destination guidance"
describes how to start the destination guidance.
Entering a destination
With the Lucca, you can enter or select destinations in different ways:
Entering a destination address
•
Selecting a point of interest
•
Copying a destination from the
•
map
Copying the destination from the
•
favourites
Reusing one of the last destina-
•
tions
Using the home address
•
Entering the destination country
First, enter the country in which your
destination is located.
Note:
This entry does not have to be repeated. Only if your destination
27
Page 28
Navigation
is in a different country than the
previous one, you must re-enter
the country.
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
Touch the Destination entry but-
➜
ton.
The Destination entry menu is dis-
played.
➜
Touch the Country button.
The list of countries displays.
Touch the country in which your
➜
destination is located.
The Address menu is displayed.
28
Page 29
Navigation
Note:
You can only select countries which
are at least partially displayed on
the currently loaded map.
Entering a destination address
To call the Address menu:
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
In the Navigation menu, touch the
➜
Destination entry button.
The Destination entry menu is dis-
played.
Touch the Address button.
➜
The Address menu is displayed.
Note:
If the country containing your destination is not displayed in the top
line (see country code), touch the
button and select the correct country. How to select a country is described in the section "Entering the destination country".
➜
➜
➜
➜
Touch the city fi eld and en-
ter the place of destination.
You can enter either the postcode
or the name of the location.
Touch the street fi eld and
enter the street.
If you know the house number
of your destination, touch the
house number fi eld to enter the
house number.
Note:
If no house number is stored for
the specifi ed street in the map
material, the house number fi eld
is deactivated.
If you want to defi ne an inter-
section as the destination,
touch the intersection fi eld to enter
the crossroad to the defi ned street.
29
Page 30
Navigation
Note:
How to save a defi ned destination
is described in the chapter "Saving
one of the last destinations".
Additional functions
Touch the More button to gain ac-
➜
cess to additional functions of the
Address menu.
The list of additional functions displays.
The following additional functions
are available:
Routing options:
•
The routing options for the
–
destination guidance can be
adjusted here.
30
For further details, read the chapter
"Specifying routing options".
•
Show:
–
Select this button to view the
address entered on the map.
For further details, read the chapter
"Working with the map".
•
Save:
–
This function allows you to save
the address entered to your favourites.
For further details, read the chapter
"Saving one of the last destinations".
Selecting a point of interest
You can display points of interest or
"POI" on the map. Points of interest
include airports, ferry ports, restaurants, hotels, petrol stations, public
institutions, etc. Points of interest
can be used for the destination guidance.
Point of interest in the current
vicinity
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
Page 31
Navigation
In the Navigation menu, touch the
➜
Destination entry button.
The Destination entry menu is dis-
played.
Touch the Point of interest but-
➜
ton.
The Point of interest menu is dis-
played.
Note:
Points of interest from your vicinity can only be selected if the GPS
reception is suffi cient for determining the position.
Touch the ... nearby button.
➜
The submenu displays.
➜
➜
Touch the surrounding ra-
dius fi eld and select the radius in which you are looking for a
point of interest.
Touch the category fi eld
and select the category
(e.g. petrol station) from which
you want to look for points of interest.
Only those categories are available
for selection for which points of
interest can be located in the current vicinity.
31
Page 32
Navigation
➜
➜
➜
➜
Touch the subcategory fi eld
and select the subcategory
(e.g. a petrol station of a specifi c
brand) from which you want to
look for points of interest.
Only those subcategories are available for selection for which points
of interest can be located in the
current vicinity.
Touch the point of interest
fi eld to select a specifi c target.
The keyboard is displayed. If you
know a part of the description of
the point of interest, it can be entered here to shorten the list.
Touch the List button.
A list with points of interest is
displayed. The points of interest
correspond to the selected category and subcategory. They also
contain the letters you may have
entered.
Touch the entry of the point of interest to which you want to navigate.
➜
If you desire more detailed information about the point of interest,
touch the More button, followed
by Show details.
Touch the OK button to accept the
➜
selected point of interest.
Note:
You do not have to fi ll out the
fi elds Category and Subcategory.
They are only intended to restrict
the list of points of interest in the
Point of interest fi eld. This list can
quickly become very extensive,
particularly at larger locations.
How to save a defi ned destination is
described in the chapter "Saving one
of the last destinations".
Additional functions
Touch the More button to gain ac-
➜
cess to additional functions of the
Point of interest menu.
The list of additional functions displays.
32
Page 33
Navigation
The following additional functions
are available:
•
Routing options:
–
The routing options for the next
destination guidance can be
adjusted here.
For further details, read the chapter
"Specifying routing options".
•
Show:
–
Select this button to view the
address entered on the map.
For further details, read the chapter
"Working with the map".
•
Save:
–
This function allows you to save
the address entered to your favourites.
For further details, read the chapter
"Saving one of the last destinations".
Point of interest at a specifi c
location
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
Touch the Destination entry but-
➜
ton.
The Destination entry menu is dis-
played.
In the menu, touch the Point of
➜
interest button.
The Point of interest menu is dis-
played.
➜
In the Point of interest menu, touch
the ... in a town button.
The submenu displays.
33
Page 34
Navigation
Note:
If the country containing your
destination is not displayed in the
fi rst line, touch the
twice and select the correct country. How to select a country is described in the chapter "Entering
the destination country".
➜
➜
Touch the city fi eld and en-
ter the location in which you
want to look for a point of interest.
You can enter either the postcode
or the name of the location.
Touch the category fi eld
and select the category (e.
g. "culture") from which you want
to look for points of interest.
button
Only those categories are available for selection for which points
of interest can be located in the
specifi ed town.
➜
➜
➜
Touch the Subcategory fi eld
and select the subcategory
(e.g. "museum" or "theatre") from
which you want to look for points
of interest.
Only those subcategories are available for selection for which points
of interest can be located in the
specifi ed town.
Touch the Point of Interest
fi eld.
The keyboard is displayed. If you
know a part of the description
of the point of interest, it can be
entered here to shorten the list.
However, you may also continue
without an entry.
Touch the List button.
A list with points of interest is dis-
played. The points of interest displayed correspond to the selected
category and subcategory. They
also contain the letters you may
have entered.
34
Page 35
➜
Touch the entry of the point of interest to which you want to navigate.
➜
If you desire more detailed information about the point of interest,
touch the More button, followed
by Show details.
➜
Touch the OK button to accept the
selected point of interest.
Special national destination
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
➜
Touch the Destination entry button.
The Destination entry menu is dis-
played.
➜
In the menu, touch the Point of interest button.
The Point of interest menu is dis-
played.
Navigation
In the Point of interest menu, touch
➜
the ... nationwide button.
The submenu displays.
Note:
If the country containing your
destination is not displayed in the
fi rst line, touch the
button
35
Page 36
Navigation
twice and select the correct country. How to select a country is described in the chapter "Entering
the destination country".
➜
➜
➜
➜
Touch the Category fi eld
and select the category
(e.g. airport) from which you want
to look for points of interest. The
selection offers only categories
whose points of interest have a national meaning.
Touch the Point of Interest
fi eld.
The keyboard is displayed. If you
know a part of the description
of the point of interest, it can be
entered here to shorten the list.
However, you may also continue
without an entry.
Touch the List button.
A list with points of interest is dis-
played. The points of interest displayed correspond to the selected
category. They also contain the
letters you may have entered.
Touch the entry of the point of interest to which you want to navigate.
If you desire more detailed infor-
➜
mation about the point of interest,
touch the More button, followed
by Show details.
Touch the OK button to accept the
➜
selected point of interest.
Copying a destination from
the map
This function allows you to select the
destination for a destination guidance directly on the map. In addition
to towns and streets, you can also
quickly select points of interest.
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
➜
Touch the Destination entry button.
The Destination entry menu is dis-
played.
➜
In the destination entry, touch the
On map button.
The map is displayed.
36
Page 37
Moving the map section
To view the desired destination area
on the map, you can move the map
section and zoom in/out.
•
Zoom / Moving
Touch this button to switch be-
tween the zoom and move mode.
–
Zoom: In the zoom mode, you
can enlarge and reduce the
map section.
Enlarge: Draw a diagonal starting at the top left corner.
Reduce: Draw a diagonal starting at the bottom right corner.
Note:
The map section can also be reduced or enlarged using the buttons
/ .
Navigation
Move: The map can be moved
–
in the move mode. For this purpose, touch the map, hold the
pen or your fi nger pressed and
move the map area in the desired direction.
Touch the town (street or point of
➜
interest) to be defi ned as the destination for a few seconds.
The town is identifi ed by an orange-dotted circle.
A window with information about
the selected location is displayed.
This window also allows you to call
up functions for the location.
37
Page 38
Navigation
You have the following options:
•
Touch the Start navigation but-
ton to use the selected location as
place of destination for the destination guidance.
Notes:
•
This function is only available
with GPS reception.
•
If you use this function during a
destination guidance, all previously defi ned route locations
(stages and destination points)
are deleted!
•
Touch the Save button to save
the selected destination. You can
select the destination at any time
from the list of favourites.
38
Touch the Search nearby button
•
to search for a point of interest in
the vicinity of the selected destination.
Touch the Interim dest. button to
•
add the selected destination to
a route (as the next stage to be
approached). The route is immediately recalculated and the destination guidance is subsequently
continued.
Touch the Add button to add the
•
selected destination to the end
of a route (as the last stage). The
route point is subsequently identifi ed on the map by a fl ag and also
entered in the route point list in
the Itinerary menu.
Note:
If you use this function during a
destination guidance, the route
is immediately recalculated and
the destination guidance is subsequently continued.
Touch the
•
the map view without executing a
function.
button to return to
Page 39
Copying the destination
from the favourites
The favourites contain all the destinations you saved using the Save button.
You can perform the following in this
menu:
Accepting destinations for the
•
destination guidance
Renaming destinations
•
Deleting saved destinations.
•
Copying a favourite for destination
guidance
In the main menu, touch the Navi-
➜
gation button.
The Navigation menu is displayed.
Touch the Destination entry but-
➜
ton.
The Destination entry menu is dis-
played.
Touch the Favourites button.
➜
The Favourites menu is displayed.
Navigation
➜
Touch the desired destination.
Note:
If you want to view the address
of a saved destination, touch this
destination. Touch More, followed
by Show details.
Touch the OK button.
➜
The Address menu is displayed.
The address of the selected destination is entered in the corresponding fi elds.
How to delete or rename a saved destination is described in the chapter
"Managing destinations".
Additional functions
➜
In the Favourites menu, touch the
More button to obtain access to
39
Page 40
Navigation
additional functions in the Favourites menu.
The list of additional functions displays.
The following additional functions
are available:
Show details:
•
Touch the Show details button
–
to show the address of the selected destination.
Delete entry:
•
Touch the Delete entry button
–
to delete the selected destination.
Delete all:
•
Touch the Delete all button to
–
delete all the destinations from
the Favourites.
For further details read the chapter
"Deleting a destination".
Rename entry
•
Touch the Rename entry but-
–
ton to change the designation
of the selected destination.
40
Copying one of the last
destinations
The destinations approached last are
automatically stored in the Last desti-
nations list.
You can perform the following in this
list:
•
Accepting a destination for the
destination guidance
•
Saving a destination in the Fa-
vourites
•
Deleting one destination or all
destinations
•
Calling details about a destination
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
➜
Touch the Destination entry button.
The Destination entry menu is dis-
played.
➜
Touch the Last destinations button.
The Last destinations menu is dis-
played.
Page 41
Select the desired destination.
➜
Touch the OK button.
➜
The destination is accepted in the
Address menu, and the addresses
are entered in the corresponding
fi elds.
Additional functions
In the Last destinations menu,
➜
touch the More button to obtain
access to additional functions in
the Last destinations menu.
The list of additional functions displays.
Navigation
The following additional functions
are available:
•
Show details:
–
Touch this button to show the
address of the selected destination.
•
Delete entry:
–
Touch this button to delete the
marked destination.
•
Delete all:
–
Touch this button to delete all
the entries from the Last desti-
nations list.
•
Save under Favourites:
–
Touch this button to save the
marked destination in the Fa-
vourites.
Using the home address as
destination
If your home address is saved, you
can quickly navigate home from any
location.
How to save your home address is
described in the chapter "Home address".
41
Page 42
Navigation Managing destinations
➜
In the main menu, touch the Navigation button.
The Navigation menu is displayed.
➜
Touch the Home button.
The route calculation is performed
and the destination guidance
starts.
Note:
The route type used for the route
calculation is automatically selected from the setting which you defi ned in the Routing options menu.
Managing destinations
Two lists are available in which individual destinations are saved:
Favourites
•
Last destinations
•
Each destination you enter and the
destinations from the Last destina-
tions list can be saved in the Favourites. This is particularly useful if you
want to approach this destination
repeatedly.
Destinations from the Favourites can
be renamed.
You can delete individual destinations
from both lists.
Saving destinations
Prerequisite:
You entered a destination as de-
•
scribed in the chapter "Entering a
destination".
Touch the More button.
➜
Touch Save.
➜
A menu for entering a name is displayed.
42
Page 43
Enter a name for the destination.
➜
Touch the OK button.
➜
The destination is saved in the
Favourites.
Saving one of the last destinations
Prerequisite:
You opened the Last destinations
•
list as described in the chapter
"Copying one of the last destinations".
Select the destination to be saved
➜
in the Last destinations list.
Touch the More button.
➜
Touch Save under Favourites.
➜
Managing destinations
A menu for entering a name is displayed.
Enter a name for the destination.
➜
Touch the OK button.
➜
The destination is saved in the Favourites.
Renaming a destination
Open the Favourites menu as de-
➜
scribed in the chapter "Copying
the destination from the favourites".
Select the destination to be re-
➜
named.
Touch the More button.
➜
Touch Rename entry.
➜
A menu for entering a name is displayed.
43
Page 44
Managing destinations
Enter a new name for the destina-
➜
tion.
Touch the OK button.
➜
The destination is renamed.
Deleting a destination
Prerequisite:
You opened the Favourites as de-
•
scribed in the chapter "Copying
the destination from the favourites".
- or You opened the Last destinations
•
list as described in the chapter
"Copying one of the last destinations".
Select the destination to be de-
➜
leted from the list.
Touch the More button.
➜
Touch Delete entry.
➜
A confi rmation menu is displayed.
44
➜
Touch OK to delete the destination.
- or -
➜
Touch
tination.
Deleting the complete list with
destinations
Prerequisite:
•
You opened the Favourites as de-
scribed in the chapter "Copying the
destination from the favourites".
- or -
•
You opened the Last destinations list
as described in the chapter "Copying one of the last destinations".
➜
Touch the More button.
➜
Touch Delete all.
A confi rmation is displayed.
Touch OK to delete the list.
➜
- or Touch
➜
to not delete the des-
not to delete the list.
Page 45
Route planning with
stages
You can also perform the route planning in the comfort of your home,
even without GPS reception.
You can plan any number of routes
with several route points, e.g. for
your vacation. They can be saved and
used for destination guidance at a
later time.
Planning a route
In the Navigation menu, touch the
➜
More button.
Touch Itinerary.
➜
The Itinerary menu is displayed.
Route planning
Touch the Add button to enter the
➜
fi rst route point.
The Destination entry menu is dis-
played.
Defi ne the route point similar to
➜
the destination entry. For more information, see the chapter "Entering a destination".
Touch the Add button.
➜
The Itinerary menu is displayed.
The destination entered is listed
as route point 1.
Repeat the steps for all additional
➜
destinations to be added to the
route.
45
Page 46
Route planning
Editing a route
You can insert additional route points
in the routes at any time, change the
order of route points or display the
route on the map.
The Itinerary menu provides various
buttons for this purpose:
Touch the route point you want to
➜
select.
If the list features more than 3 entries, use the following buttons:
Touch the
➜
the list by one page (3 elements).
➜
Touch the
down the list by one page (3 elements).
➜
To scroll several pages, touch the
corresponding button repeatedly.
Note:
If the list features more than 3 elements, the scroll bar indicates the
current position in the list.
Changing the order of route points
•
Move route point up:
➜
Select the route point to be moved.
➜
Touch the More button.
button to scroll up
button to scroll
Touch the Route point up button.
➜
The Itinerary menu is displayed
again. The selected route point is
moved up one position in the route
list.
Repeat this process until the route
➜
point appears at the correct position in the route list.
Move route point down:
•
Select the route point to be moved.
➜
Touch the More button.
➜
Touch the Route point down but-
➜
ton.
The Itinerary menu is displayed
again. The selected route point is
moved down one position in the
route list.
Repeat this process until the route
➜
point appears at the correct position in the route list.
Deleting a route point
Select the route point to be de-
➜
leted.
Touch the More button.
➜
Touch Delete from route.
➜
The route list is displayed again.
46
Page 47
Route planning
Deleting a complete route list
If you want to delete all the route
points from the current route list:
➜
Touch the More button.
➜
Touch Delete the complete list.
Saving a route
In the Destination entry menu,
➜
touch the More button.
Touch Save route.
➜
A menu for entering a name is displayed.
Enter a name for the route.
➜
Touch OK.
➜
Note:
The route points are saved. If you
load a saved route, it must be recalculated.
Loading a route
In the Destination entry menu,
➜
touch the More button.
Touch Load route.
➜
Touch the route to be loaded.
➜
The Itinerary menu with the selected route is displayed.
Calculating a route
You can use a planned route for the
destination guidance or calculate before the trip to gain an overview of
the route in advance. The advance
route calculation does not require
GPS reception.
Starting the destination guidance
(GPS reception required)
For the destination guidance of a
planned route, the current location
is the starting point. The fi rst stage
is the travel to the fi rst route point
entered.
To start the destination guidance,
load the desired route.
➜
Touch the Start navigation but-
➜
ton.
The route is being calculated. The
map is displayed. Additional information about destination guidance can be found in the chapter
"Destination guidance".
Calculating the route without GPS
reception
For the calculation of a planned route
without GPS reception, the fi rst route
47
Page 48
Route planning
point entered is the starting point of
the route.
After calculating the route, you can view
it on the map or take a virtual trip.
For the route calculation:
load the desired route.
➜
Touch the Calculate button.
➜
The route is being calculated. A
window displays the progress of
the calculation.
After the calculation, the Itiner-
ary menu is displayed again. The
Calculate button is no longer
available. Instead, you can view
the distance and the anticipated
travel time. The route list displays
the distances and the anticipated
travel times for each stage.
48
Showing the route on the map
Touch the Show button to display
➜
the entire route on the map.
The map is displayed.
The route is highlighted in blue.
The route points entered are iden-
tifi ed by fl ags.
Travelling the route (simulation)
Touch the map.
➜
A selection menu is displayed.
Touch the Simulation button.
➜
The route is automatically travelled
and driving recommendations are
output.
Touch
➜
tion. Otherwise, the simulation is
repeated.
Note:
The length of the stage may not
exceed 100 kilometres for the
simulation.
to end the simula-
Page 49
Specifying routing
options
In the Routing options menu, you can
defi ne the speed profi le of your vehicle, select the type of routing and exclude certain streets from usage. The
routing options are retained for every
subsequent destination guidance.
In the Navigation menu, touch the
➜
Settings button.
The Settings menu displays.
Touch the
➜
the list by one page (3 elements).
Touch the
➜
the list by one page (3 elements).
To scroll up or down the list by several pages,
touch the corresponding button
➜
repeatedly.
In the Settings menu, touch the
➜
Routing options button.
The Routing options menu is dis-
played.
button to scroll up
button to scroll down
Specifying routing options
Touch the Speed profi le fi eld to
➜
change between the available profi les.
Touch the Type of routing fi eld
➜
to change between the various
modes:
Dynamic
•
The TMC function is switched
–
on for this option. That is, traffi c reports are included in the
calculation of the route. Without TMC reception, the fast
route is calculated.
Fast
•
This option calculates the short-
–
est route for the required time.
49
Page 50
Specifying routing options TMC function
Short
•
This option calculates the
–
shortest route for the kilometres to be travelled.
Touch the fi elds Motorways, Fer-
➜
ries and Toll roads in succession
to include the road types in the
route calculation or to avoid them:
Permitted
•
This option includes the cor-
–
responding street type in the
calculation of the route.
Avoid
•
This option avoids the corre-
–
sponding street type as far as
possible.
Forbidden
•
This option does not include
–
the corresponding street type
in the calculation of the route.
50
TMC function
The Traffi c Message Channel (TMC)
supplies your Lucca with traffi c reports that are broadcast by the radio
stations with the RDS (Radio Data System) signal.
The broadcast traffi c reports can be
included in the route calculation by
the Lucca. An alternate route is calculated in case of traffi c obstructions.
The Lucca allows you to a dynamic
destination guidance that adjusts to
the respective traffi c situation. You
can also display the TMC reports.
TMC is available in the following countries: Belgium, Denmark, Germany,
England, Finland, France, Italy, Netherlands, Norway, Austria, Spain, Sweden, Switzerland and Czech Republic.
Connecting the TMC antenna
Connect the supplied TMC anten-
➜
na to the TMC antenna input 9 on
the rear side of the Lucca.
Attach the TMC antenna with the
➜
suction cups as parallel as possible to the instrument panel.
The Lucca can now receive traffi c
reports, if available.
Page 51
Switching on the TMC
function
The TMC function is activated in the
Routing options menu (see "Specifying routing options"):
➜
In the Navigation menu, touch the
Settings button.
The Settings menu displays.
➜
Touch the Routing options button.
The Routing options menu is displayed.
➜
Touch the Type of routing fi eld to
change to Dynamic.
The TMC function is switched on
if the Dynamic option is set. If no
TMC signal is available, the Lucca
calculates the fast route.
Adjusting TMC options
In the TMC menu, you can adjust
whether the destination guidance
should be automatically changed by
the Lucca in case of traffi c obstructions or whether it should wait for
your confi rmation:
➜
In the Navigation menu, touch the
Settings button.
TMC function
Touch the
➜
screen with the TMC button appears.
➜
Touch the TMC button.
➜
Touch the Route modifi cation but-
ton to change between the two
options:
•
Automatically: The Lucca automatically guides you around the traffi c
obstruction.
With confi rmation: The Lucca sug-
•
gests an alternate route in case
of a traffi c obstruction. The route
changes can be confi rmed or rejected.
Touch OK.
➜
button until the
Showing traffi c reports
In the Navigation menu, touch the
➜
TMC button.
The traffi c reports are displayed.
Touch the arrow symbols to change
➜
between messages.
Note:
A detailed description for operating the traffi c reports can be found
in the chapter "Information".
51
Page 52
Destination guidance
Destination guidance
Prerequisite:
•
You entered a place of destination
as described in the chapter "Entering a destination".
- or -
•
You selected a place of destination
from the Favourites as described in
the chapter "Copying the destination from the favourites".
- or -
•
You selected a place of destination from the Last destinations list
as described in the chapter "Copying one of the last destinations".
- or -
•
You planned or loaded a route (as
described in the chapter "Route
planning with stages").
Touch the Start navigation button.
➜
The route is being calculated.
The map is displayed. Your cur-
rent position is represented by a
yellow triangle. The route is highlighted in blue.
Touch the buttons More and
➜
in succession to show or hide
additional buttons.
Notes:
The route is calculated with
•
the set routing options. These
settings can be viewed and
changed via the Routing options
menu. For detailed information,
read the chapter "Specifying
routing options".
If the destination guidance for
•
a planned route is started, the
starting point is always the
current position. The fi rst stage
of the route is the travel to the
fi rst route point.
or
52
Page 53
Destination guidance
Disturbed GPS reception
A message notifi es you if no adequate
GPS signal is received.
If you are in an enclosed room, move
to the outside. The Lucca requires an
unobstructed line of sight to the sky.
The map shows the
GPS reception is insuffi cient. The
destination guidance is stopped. As
soon as the GPS reception is re-established, the Lucca automatically
recognises whether your position
has changed and, if necessary, recalculates the route. At that time, you
can simply continue your destination
guidance.
symbol if the
Quitting the destination guidance
➜
Touch this button
the destination guidance.
A confi rmation dialogue appears.
Touch OK to quit the destination
➜
guidance.
If you quit the destination guidance
before reaching your destination, the
Navigation menu opens. You can now
enter a new destination or continue
the destination guidance to the original destination by selecting the original destination again from the "last
destinations".
Reaching the place of destination
As soon as you have reached the destination point, the message "You have
reached your destination" appears.
At this point, the map displays only
your current position (yellow arrow).
to quit
53
Page 54
Working with the map
Working with the map
Map operation
In this section you learn which information and which processing options are available in the map view.
Depending on whether you display a
map without or during the destination guidance, different options are
available for operation.
Showing a map
You can display the map:
•
During route planning
•
To display destinations on the
map
•
To copy destinations from the map
for the destination guidance
You can open the map view as follows:
•
Via the Show map button in the
Navigation menu.
•
Via the On map button in the Destination entry menu.
•
Via the Show button in the additional functions in the Address
menu after selecting a destination.
54
Touching the map
➜
Briefl y touch the map to display
additional functions.
Depending on whether you are currently in an active destination guidance or only display the map, only
certain functions are available.
➜
Touch the map for a few seconds
to defi ne the city (street or point
of interest) as the destination.
(Identifi ed by an orange-dotted
circle around the city.)
A window with information about
the selected location is displayed.
This window also allows you to call
up functions for the location.
For further details, please read the
section "Copying a destination from
the map".
Buttons
Different buttons are available in the
map view with which you can adjust
the display according to your needs.
Page 55
Working with the map
In map view without GPS reception
•
Showing/hiding buttons
–
More
This button allows you to hide
the additional buttons to gain
a better overview of the map.
Touching it again redisplays the
auxiliary buttons.
In map view with GPS reception
Auto mode
•
More
–
Touch this button to restore
the standard view of the map
after making changes. In doing
so, the settings for the map orientation and auto zoom are applied, the auxiliary buttons are
hidden and the map is centred
according to your position.
Additional buttons
•
/
–
These buttons allow you to switch
the additional buttons that are
distributed onto 2 pages.
•
Fix map
Fix position
This button is only active during a
destination guidance. Touch this
button to fi x the map or the position.
Fix map
–
In this mode, the map is fi xed
and the current position (yellow
arrow) moves across the map.
Fix position (standard setting)
–
In this mode, the map is continually moved so that the current position (yellow arrow) is
always closely centred in the
bottom third of the map.
Note:
The "Map fi xed" mode is automatically set as soon as you move the
map; otherwise, the map would
constantly jump back to the current position. This mode should
also be set if you want to select
destinations from the map during
the destination guidance.
Zoom
•
Touch this button to switch be-
tween the zoom and move mode.
/
/ Moving
55
Page 56
Working with the map
–
Zoom: In the zoom mode, you
can enlarge or reduce the
map section.
Enlarge: Draw a diagonal starting
at the top left corner.
Reduce: Draw a diagonal starting at the bottom right corner.
Note:
The map section can also be reduced or enlarged using the buttons
/ .
–
Move: The map can be moved
in the move mode. For this purpose, touch the map, hold the
pen or your fi nger pressed and
move the map area in the desired direction.
•
Showing the complete route
–
Touch this button , to display
the complete route on the
map.
•
Map orientation ...
in travel direction
to the north
Touch this button to orient the
map in travel direction or to the
north.
/
3-D view
•
–
Touch this button to display
the map in a three-dimensional
representation from a bird's
eye view.
–
Touch the More button to display the map in two-dimensional form again.
•
TMC traffi c reports
Touch this button to display cur-
rent traffi c reports. (TMC reception must be available)
•
Quit navigation
Touch this button to quit the des-
tination guidance.
Additional functions
Briefl y touch any position on the
➜
map.
The menu with the additional func-
tions displays.
Depending on whether you are
currently in a destination guidance or only display the map, only
certain functions are available.
56
Page 57
Day/night mode
Touch the Night mode button to
➜
switch the night mode for the
screen on or off.
Mute
Touch the Mute button to switch
➜
the voice instructions on or off.
Settings
The Preferences button calls up the
Settings menu.
For further details, read the chapter
"Basic settings of the Lucca".
Working with the map
All other buttons are effective only
during the destination guidance:
Block road: For further details,
•
read the section "Blocking route
segments".
Interim dest.: For further details,
•
read the section "Inserting an interim destination".
Next dest.: For further details,
•
read the section "Approaching the
next destination".
Route options: For further de-
•
tails, read the section "Routing
options".
Simulation: For further details,
•
read the section "Routing options".
To close the menu with the additional
functions and to return to the map,
touch the
➜
button.
57
Page 58
Map display during destination guidance
Map display during
destination guidance
During a destination guidance, the
map display shows different navigation tools, route information and
signpost information.
Caution
The information on the digital road
maps may be incorrect due to shortterm changes (construction, etc.)!
The traffi c situation and the local
signpost information have priority
over the information of the Lucca.
58
Navigation tools
The left and lower area of the map display the following navigation tools:
•
Your position on the map is indicated by
tion guidance, the map section
moves so that your position is
always displayed as close to the
center of the map as possible
("Moving Map").
•
In case of actions that must be
executed in brief succession, the
next to one action is displayed in
the small upper arrow fi eld.
•
The large lower arrow fi eld displays the next action and the distance to the next action.
. During the destina-
Page 59
Map display during destination guidance
–
If you come closer to the action location, a yellow bar is
displayed to the right of the
large arrow fi eld instead of the
distance:
–
–
–
: Estimated time of
arrival.
: Estimated remaining
travel time.
: Remaining distance to
destination.
Signpost information
–
The more yellow bars are displayed, the closer you are to
the location of the next action.
•
The upper street fi eld displays the
next street name.
•
The lower street fi eld displays the
current street name.
(exit signs)
The top part of the map displays information about the signpost information, e.g exist signs. If you follow
the signpost information, you reach
the next street which is displayed in
the upper street fi eld:
Route information
The right area of the map displays the
following route information:
Note:
This information can only be displayed if it is part of the map material.
–
: This symbol represents
stages. All information below it
refers to the next destination.
59
Page 60
Map display during destination guidance
Speed limit
The right area of the map displays the
speed limit that may apply:
Note:
This information can only be displayed if it is part of the map material.
Activating additional map
information
You can use the Lucca to defi ne which
additional information is displayed on
the map. All settings are performed
in the Settings menu.
To open the Settings menu:
➜
Touch the Settings button in the
Navigation menu.
- or -
➜
Touch any part of the map and select the Preferences button.
Map information
In the Settings menu, touch Map
➜
information.
Activate the Info bar entry so that
➜
the compass and your current
speed are displayed on the map in
the lower right border.
Activate the Point of interest en-
➜
try so that all points of interest
are displayed on the map (default
setting).
Activate the Street names 2D en-
➜
try so that the street names are
displayed on the map (only possible in 2-D display).
60
Page 61
Map display during destination guidance
➜
Touch the OK button to save your
settings.
- or -
➜
Touch the
save the settings and to return to
the Settings menu.
Route information
➜
In the Settings menu, touch the
Route information button.
The Route information menu is dis-
played.
➜
Activate the desired route information with the corresponding
buttons.
button to not
The corresponding information for
the next stage (upper area) and
the complete route (lower area) is
displayed on the map.
➜
Touch the OK button to save your
settings.
- or -
➜
Touch the
save the settings and to return to
the Settings menu.
Signpost information (exit signs)
➜
In the Settings menu, touch Signpost information.
The Signpost information menu is
displayed.
➜
Touch the Show traffi c signs but-
ton to activate or deactivate the
display of the exit signs.
If you activate the button, the signpost information is displayed on
the map.
button to not
61
Page 62
Map display during destination guidance
➜
Touch the OK button to save your
settings.
- or -
➜
Touch the
save the settings and to return to
the Settings menu.
Speed limit
➜
In the Settings menu, touch Speed
limit.
The Speed limit menu is displayed.
In the Speed limit menu you can defi ne whether speed limits should
be displayed during the destination
guidance and whether you should be
warned audibly if you are exceeding
the speed limit.
•
Displaying traffi c signs
button to not
➜
Touch the Show traffi c signs but-
ton to change between the modes
"Always", "On speeding only" or
"Never".
•
Warning in a town:
Adjust the value of the speed limit
at which you want to receive an
audible warning. This setting applies only to urban areas.
➜
Touch the Warning in urban areas
button to change the value or to
set it to Never.
•
Warning in rural areas:
Adjust the value of the speed limit
at which you want to receive an
audible warning. This setting applies outside of urban areas.
➜
Touch the Warning in rural areas
button to change the value or to
set it to Never.
•
Warning
➜
Activate the Warning button to
receive a warning for speed limits
when wet.
➜
Touch the OK button to save your
settings.
Your settings are displayed on the
map.
62
Page 63
Additional functions
Additional functions
during the destination
guidance
You can perform the following during
destination guidance:
•
Inserting an interim destination
•
Skip a route point
(Approaching the next destination)
•
Block a route segment
Inserting an interim
destination
During the destination guidance, you
can insert a new interim destination
at any time. The route is then recalculated so that this interim destination
can be approached as the next destination. After reaching the interim
destination, all remaining places of
destination are selected.
An interim destination is created as
follows:
Prerequisite:
You are in the map display during
•
a destination guidance.
Briefl y touch any position on the
➜
map.
The menu with the additional functions displays.
Touch the Interim dest. button.
➜
The Destination entry menu is dis-
played.
Enter the place of destination as
➜
described in "Entering a destination".
Touch the Set as route point but-
➜
ton.
The route is recalculated and the
defi ned interim destination is selected as the next route point.
63
Page 64
Additional functions Blocking route segments
Note:
You can also select the interim
destination directly from the map
as described in the section "Copying a destination from the map".
Next, touch the Interim dest. button.
Approaching the next
destination
This function is only available if you
travel on a route with at least one intermediate destination.
Use this function if you want to skip
the next route point.
Touch the Next destination but-
➜
ton to approach the next to one
route point.
The route is recalculated and the
next but one route point is approached as the next destination.
64
Blocking route
segments
Manual blocking
You have the option of manually
blocking a route segment located on
your route to evade this road section
during the destination guidance. After a manual blocking, the route is
recalculated.
Supposing that you are on the motorways and hear a traffi c report on the
radio about a traffi c jam of 5 km on
your route. In this case, you can use
a manual blocking of the section to
evade the traffi c jam.
The manual blocking applies only to
the current destination guidance. For
a new destination guidance or after
a restart of the navigation mode, the
blocking is no longer available.
Route segments are blocked as follows:
Prerequisite:
•
You are in the map display during
a destination guidance.
Briefl y touch any position on the
➜
map.
Page 65
Blocking route segments Basic settings of the Lucca
Select the Block road entry.
➜
The Block road menu is displayed.
Basic settings of the
Lucca
Settings
You can perform settings in the Lucca
for the following areas:
•
Language
•
Home address
•
Map information
•
Route information
•
Enter the number of kilometres
➜
which you want to block, starting
with your current position.
The route is recalculated and the
blocked route segment is evaded.
The blocked segment is marked in
red on the map.
Unblocking
Briefl y touch any position on the
➜
map.
Select the Block road entry.
➜
The road blocking is cancelled
and the destination guidance uses
once again the original calculated
route.
Routing options
•
Route planning
•
TMC (traffi c information data
channel)
•
Signpost information
•
Speed
•
Auto mode
•
Time zone
•
Format
•
Display
•
Factory settings
•
Touchscreen
•
Product information
65
Page 66
Basic settings of the Lucca
In the Navigation menu, touch the
➜
Settings button to confi gure the
Lucca.
If you changed the settings in the Set-
tings menu,
touch the OK button to confi rm
➜
the changes.
- or Touch the
➜
Settings menu without saving the
changes.
Language
In the Language menu, you can select
your preferred for the menus and
voice output.
Touch the Language button.
➜
The current language is displayed.
Touch the Language: ...
➜
The language list displays.
Touch the preferred language.
➜
The selected language is loaded.
Home address
In the Home address menu, you can
store your home address so that you
can quickly navigate home from any
location.
66
button to exit the
➜
Touch the Home address button.
The Home address menu is dis-
played.
➜
Touch the Enter your home address button.
The Destination entry menu is dis-
played.
➜
Touch the Address button to enter
your home address as described
in the section "Entering a destination address".
➜
Touch the Set as home address
button.
The address is copied into the
Home address menu.
Caution:
The information in the map material
may be incorrect due to short-term
changes (construction, etc.)!
The traffi c situation and the local
signpost information have priority
over the information of the navigation system.
Page 67
Basic settings of the Lucca
Map information
In the Map information menu, you
can perform the following settings:
•
Info bar
–
Activate the entry so that the
compass and your current
speed are displayed on the map
in the lower right border.
•
Points of interest
–
Activate the entry so that all
points of interest are displayed
on the map (default setting).
•
Street names 2D
–
Activate the entry so that the
street names are displayed on
the map (only possible in 2-D
display).
Route information
In the Route information menu, you
can perform the following settings for
the entire route and the next stage:
•
Distance
•
Duration
•
Time of arrival
➜
If you activate the entries for Total
Tri p, the map shows the informa-
tion up to the destination point.
If you activate the entries for Stage
➜
Point, the map shows the information up to the next route point.
Note:
This information is displayed only
if your planned route contains several route points or you entered
at least one intermediate destination.
Routing options
In the Routing options menu, you can
defi ne the speed profi le of your vehicle, select the type of routing and exclude certain streets from usage. The
routing options remain valid for every
subsequent destination guidance.
For further details, read the chapter
"Specifying routing options".
Route planning
In the Itinerary menu, you can activate
or deactivate an automatic destination guidance for the route planning:
Touch the Automatically button
➜
to activate or deactivate the automatic function:
67
Page 68
Basic settings of the Lucca
•
Automatic activated: The Lucca
automatically guides you from the
fi rst to the last stage.
•
Automatic deactivated: After
reaching a stage, the Lucca asks
whether you want to continue the
route to the next planned stage.
You can confi rm or skip this stage.
To do so, press the Next destina-
tion button.
TMC (traffi c information data
channel)
In the TMC menu, you can adjust
whether the destination guidance
should be automatically changed by
the Lucca in case of traffi c obstructions or whether it should wait for
your confi rmation:
Note:
A detailed description of the functionality can be found in the chapter "TMC function".
Signpost information
In the Signpost information menu,
you can specify whether signpost
information, which you are to follow,
68
should be displayed during the destination guidance or not.
Touch the Show traffi c signs but-
➜
ton to activate or deactivate the
display.
Note:
This information can only be displayed if it is part of the map material.
Speed limit
In the Speed menu you can defi ne
whether speed limits should be displayed during the destination guidance and whether you should be
warned audibly if you are exceeding
the speed limit.
•
Displaying traffi c signs
➜
Touch the Show traffi c signs but-
ton to change between the modes
"Always", "On speeding only" or
"Never".
•
Warning in a town:
Adjust the value of the speed limit
at which you want to receive an
audible warning. This setting applies only to urban areas.
Page 69
Basic settings of the Lucca
➜
Touch the Warning in urban areas
button to change the value or to
set it to Never.
•
Warning in rural areas:
Adjust the value of the speed limit
at which you want to receive an
audible warning. This setting applies outside of urban areas.
➜
Touch the Warning in rural areas
button to change the value or to
set it to Never.
•
Warning
➜
Activate the Warning button to
receive a warning for speed limits
when wet.
➜
Touch the OK button to save your
settings.
Your settings are displayed on the
map.
Note:
This information can only be displayed if it is part of the map material.
Auto mode
In the Auto mode menu, you can perform the following settings:
Begin with
•
Select whether the map should
–
be displayed in 3-D view or in
2-D view by default.
3D auto zoom
•
Select whether you desire Au-
–
tozoom as default in 3-D view
during a destination guidance.
2D auto zoom
•
Select whether you desire "Low
–
autozoom", "Standard", "High
autozoom" or "No autozoom"
by default during a destination
guidance with 2-D view.
Note:
For 2-D and 3-D auto zoom, the
zoom depth is changed in reference
to your speed: If you travel slowly,
the scale becomes smaller. If you
travel faster, the scale becomes
larger. The deeper the auto zoom,
the smaller the scale of the map.
•
2D (map display)
–
Select whether the map should
be oriented to the north or in
69
Page 70
Basic settings of the Lucca
driving direction by default during a destination guidance with
2-D view.
Time zone
In the Time zone menu, you can set
the time zone that is valid for your
position. This setting is important for
the correct calculation of estimated
arrival times.
Time zone
•
Touch this fi eld to set the time
➜
zone valid for your position.
Daylight saving time
•
Touch this fi eld to toggle between
➜
daylight savings time (button with
check mark) and winter time (button without check mark).
Note:
If the time is changed at your location or if you drive into a different
time zone, you must adjust the settings.
70
Format
In the Format menu you can specify
which units of measure should be
used for times and distances and the
language to be used for the menus
and voice output of the Lucca.
Time
•
Touch this fi eld to toggle between
➜
12-hour and 24-hour display.
Distance
•
Touch this fi eld to toggle between
➜
the display in kilometres and miles.
Display
In the Representation menu, you can
set the brightness for day and night
mode.
Touch the Representation but-
➜
ton.
The Representation menu is dis-
played.
Touch the Brightness Day button
➜
to select the brightness value for
day mode.
Touch the Brightness Night but-
➜
ton to select the brightness value
for night mode.
Page 71
Basic settings of the Lucca GPS mode of operation
Factory settings
In the Factory settings menu, you can
reset the navigation software to the
factory settings.
Touch the Factory settings but-
➜
ton.
A confi rmation is displayed.
Confi rm the reset to the factory
➜
settings by touching OK.
To avoid resetting the device,
touch the
➜
Touchscreen
In the Touchscreen menu, you can rec-
alibrate (align) the touchscreen if it
responds imprecisely to touches.
Touch the Start calibration button
➜
and follow the instructions on the
screen.
Product information
Touch this fi eld to display the ver-
➜
sion of the map being used and
the version of the navigation software.
button
GPS mode of operation
The Global Positioning System (GPS)
was developed in the 70s by the US
military.
GPS is based on a total of 24 satellites that are orbiting the earth and
sending out signals. The GPS receiver
receives these signals and calculates
its distance to the individual satellites using the propagation time of
the signals. This information is then
used to derive its current geographical position.
The positioning requires signals from
at least 3 satellites. Starting with the
fourth one, it is possible to also determine height above mean sea level.
The positioning is carried out with an
accuracy to 3 metres.
Destination guidance with GPS. The
supplied map material also contains
the geographic coordinates of points
of interest, streets and cities that you
can view on the screen of the Lucca.
This allows the navigation system to
calculate a route from a starting point
to a place of destination.
71
Page 72
GPS mode of operation Using the SD/MMC card
If the Lucca receives the signals from
at least 3 satellites, it can determine
its position and display it on the map.
This position can then be used as the
starting point for a route calculation.
Since a positioning and position display is carried out once every second,
you can view your movement on the
map.
72
Using the SD/MMC card
You can use an SD/MMC card with
the Lucca for the following:
Loading navigation data from
•
other countries (chapter "Installing the map material")
Playing audio data
•
(chapter "MP3 player")
Calling up image data
•
(chapter "Picture Viewer")
The SD/MMC cards may have a capacity of up to 4 GB and must be
formatted using the FAT 16 or FAT 32
format.
Preparation
The fi les can be stored either at the
top directory level or in subdirectories. You can also mix different fi le
formats within a directory. The MP3
player plays only the audio fi les and
ignores the image fi les. Likewise, the
Picture Viewer shows only the image
fi les.
Page 73
Using the SD/MMC card MP3 player
Audio fi les
(MP3 player)
MP3 fi les
(ID3 tags version
1 and 2)
WMA GIF (max. 2.2 mill.
OGG BMP (max. 13 MB)
Image fi les
(Picture Viewer)
JPG (max. 2.2 mill.
pixel)
pixel)
Inserting the SD/MMC card
The SD/MCC card slot is located on
the right side of the Lucca.
➜
Push the SD/MMC card into the
SD/MMC card slot according to
the marking on the slot until the
card engages.
Removing the SD/MMC card
➜
You quit the MP3 or Picture Viewer
menu by touching the button.
Carefully push on the SD/MMC
➜
card in the slot until it disengages.
The SD/MMC card is ejected from
the slot. Remove the card.
MP3 player
You can use the Lucca to play audio
fi les from an SD/MMC card. The Lucca recognises the formats MP3, WMA
and OGG. The playback uses either
the internal loudspeaker or connected
headphones.
The chapter "Using the SD/MMC card"
provides information about the use
and preparation of the card.
Starting the MP3 player
If you are in a different operating
mode,
➜
press the MENU button for longer
than 3 seconds.
The main menu displays.
73
Page 74
MP3 player
Touch the Music Player button.
➜
The MP3 menu is displayed.
Operating the MP3 player
In the MP3 menu, you can operate the
MP3 player and calling the MP3 list.
10
11
12
13
18 17 16 14
: Playing the most recent MP3 fi le
; Playing the MP3 fi le repeatedly/
Exiting the repeat function
< Calling the MP3 list
= Muting the sound/
Cancel mute
> Volume control
15
? Playing the previous/next MP3 fi le
@ Ending playback (Stop)
A Interrupting playback (Pause)/
Continuing playback
B Closing the MP3 player and
returning to the main menu
Note:
The MENU button (long press) allows you to change to the navigation or the Picture Viewer without
ending the MP3 playback.
MP3 list
If you touch the FILE button in the
MP3 player, the MP3 lists is called up
in the MP3 list menu. It lists all the
music data and directories and you
can select them directly.
74
Page 75
MP3 player Picture Viewer
Picture Viewer
You can view images with the Lucca
that are stored on a SD/MMC card.
The Lucca recognises image data in
19
the format JPG, GIF and BMP.
The chapter "Using the SD/MMC card"
provides information about the use
20
and preparation of the card.
22
C Buttons (arrows) for scrolling the
music data in the MP3 list
D Moving up one directory level
E Music fi le (or directory) for direct
selection
F Returning to the MP3 menu (MP3
player)
21
Starting the Picture Viewer
If you are in a different operating
mode,
➜
press the MENU button for longer
than 3 seconds.
The main menu displays.
Touch the Picture Viewer button.
➜
75
Page 76
Picture Viewer
The Picture Viewer menu and the
fi rst recognised image fi le are displayed.
Operating the Picture
Viewer
In the Picture Viewer menu, you can
view images and start the slide show.
23
27
26
G Buttons (arrows) for scrolling the
image fi les
H Image fi les for direct selection
I Starting the slide show
J Starting the ffull-screen mode
K Closing the Picture Viewer and
returning to the main menu
76
24
25
Slide show
If you touch the SLIDE button in the
Picture Viewer, all images are displayed in 3 second intervals.
At the end of the slide show, a reference appears whether the fi rst image
should be displayed.
To cancel the slide show, touch
➜
the current image.
The Picture Viewer menu is dis-
played again.
Page 77
Picture Viewer Installing the map material
Full-screen mode
If you touch the FULL button in the
Picture Viewer, the current image is
displayed in full-screen mode. Use
the arrow symbols to change to the
previous or next image fi le.
To return to the Picture Viewer
➜
menu, touch the current image.
Installing the map
material
The map material of the country in
which the Lucca was purchased is
preinstalled in the memory of the
Lucca. This map material is also contained on the enclosed CD/DVD for a
future restore. Depending on the purchase version, the CD/DVD may also
contain other map material.
The map material can be installed
only via an SD/MMC card in the memory of the Lucca.
Saving map material on the
SD/MMC card
Copy the map material with a PC
from the CD/DVD to the SD/MMC
card. Use it for:
An external map reader
•
- or The Lucca as a map reader via the
•
USB port
77
Page 78
Installing the map material
Using map material with the
Lucca
➜
Switch on the Lucca by pressing the
On/Off switch for a few seconds.
The SD/MCC card slot is located on
the right side of the Lucca.
➜
Push the SD/MMC card into the
SD/MMC card slot according to
the marking on the slot until the
card engages.
A dialogue menu displays.
➜
Please follow the instructions.
You have two options for the use
of the map material:
–
Load the map material into the
main memory and overwrite the
old map material.
- or –
Use the map material directly
from the SD/MMC card.
➜
Touch the OK button.
The road map is activated and the
Navigation menu is displayed.
78
Removing the SD/MMC card
Carefully push on the SD/MMC
➜
card in the slot until it disengages.
The SD/MMC card is ejected from
the slot. The map can now be removed.
Page 79
Updading the software of Lucca Technical data
Updating the software
of the Lucca
To ensure that your Lucca is always
state-of-the-art, Blaupunkt offers software downloads at regular intervals.
They can be found on the Blaupunkt
Internet site www.blaupunkt.com.
Technical data
Operating system:
Microsoft Windows
CE 5.0
CPU: Atlas II Dual Core
Processor (300 MHz)
Main memory:
64 MB DRAM
512 MB NAND Flash
Unit size (mm):
115 (W) x 80 (L) x 25 (H)
Weight (g): approx. 190
GPS: QuickFind-Technologie
Centrality GPS
20 channels
Battery: Rechargeable battery
(Li-lon 1230 mA)
Sound: Max 1.5 W speaker
built-in
Operating temperature:
-20 °C ... 60 °C
Storage temperature:
-30 °C ... 70 °C
Music Player:
MP3 (ID3 tag version
1/2), WMA, OGG
79
Page 80
Technical data Disposal of old unit
Picture Viewer:
JPG (max. 2.2 mill. pixel),
GIF (max. 2.2 mill. pixel),
BMP (max. 13 MB)
SD/MMC card:
max. 4 GB
80
Disposal of old unit
(EU countries only)
Do not dispose of your old unit in
the household trash!
Please use the return and collection
systems available to dispose of the
old unit.
Page 81
Service Warranty
Service
In some countries Blaupunkt offers
a specifi c repair service including a
pick-up service.
In case your Lucca has to be sent to
Blaupunkt for service you can order
a pick-up service for your device on
the internet.
Refer to www.blaupunkt.com to
check if this service is available in
your country.
Warranty
We provide a manufacturer's warranty for our products purchased within
the European Union. For devices purchased outside the European Union,
the warranty terms issued by our respective responsible domestic agency are valid. The warranty period for
the battery is 1 year.
The warranty terms can be called
up under www.blaupunkt.com or requested directly from:
Blaupunkt GmbH, Hotline
Robert-Bosch-Str. 200
D-31139 Hildesheim
81
Page 82
FAQ
Frequently asked
questions / FAQ
Why does the Lucca require GPS
reception?
The system must know where it is located or where it is moving. This is
accomplished with the help of GPS
satellites. Without GPS reception,
navigating is not possible.
What can I do if the Lucca receives
GPS signals poorly?
If you change your location and the
device is switched off, e.g. after travel
by plane, it is possible that the Lucca
cannot establish a GPS reception for
an extended period of time.
Move to the outside. The Lucca automatically searches for GPS signals.
After a few minutes, your Lucca is operational again.
In which countries is TMC available?
The following countries currently offer TMC service: Germany, Denmark,
Sweden, Finland, Norway, England,
82
Belgium, Netherlands, Austria, Switzerland, France, Italy, Spain and
Czech Republic. Hungary and Poland
plan to introduce it.
Which cards can I use?
Commercial SD or MMC cards.
Which data format is required for an
SD/MMC card?
FAT 16/32.
What can I use an SD/MMC card for
with the Lucca?
You can use SD cards with a capacity
of up to 4 GB. The Lucca recognises
the following data:
•
Navigation data from other countries
•
MP3/WMA data for playback in the
MP3 player
•
JPG data for playback in the Picture Viewer
Page 83
FAQ
Can the navigation software be
changed?
Yes. Simply insert the SD/MMC card
in the SD/MMC card slot or use the
USB connection, and you can immediately navigate with the new data.
The internal navigation software remains intact and you can use either
the internal navigation software or
the one on the SD/MMC card for the
selection.
Is the old internal navigation software overwritten with a change of
the navigation software?
No, the system can navigate with the
internal as well as the external data. If
the external data (SD/MMC card) are
used for navigation, the SD/MMC slot
for the MP3 playback for the Lucca is
unavailable during this time.
Can the internal navigation software
be changed?
Yes. The data can be loaded in the
internal memory. For this purpose,
insert the SD/MMC card in the SD/
MMC card slot or connect the Lucca
via the USB-port with your PC and initiate the loading process via menu.
How long does the loading take from
the SD/MMC card to the internal
memory?
The loading process lasts approx.
15 minutes and is dependent upon
the data size. For this reason, the
individual countries are delivered as
completely manufactured maps.
The data do not have to be loaded
from the SD/MMC card into the internal memory.
Is it possible to play WMA fi les with
DRM protection?
The playback of WMA fi les with Digital
Rights Management protection (WMADRM) is not possible since the license
key is not transferred during the transfer of the WMA fi le from the PC.
The playback of WMA fi les without DRM
protection is, of course, possible.
83
Page 84
Country: Phone: Fax:/www:
Germany (D) 0180-5000225 05121-49 4002
www.blaupunkt.com
Austria (A) 01-610 39 0 01-610 39 391
Belgium (B) 02-525 5444 02-525 5263
Denmark (DK) 44-898 360 44-898 644
Finland (FIN) 09-435 991 09-435 99236
France (F) 01-4010 7007 01-4010 7320
Great Britain (GB) 01-89583 8880 01-89583 8394
Greece (GR) 210 94 27 337 210 94 12 711
Ireland (IRL) 01-46 66 700 01-46 66 706
Italy (I) 02-369 62331 02-369 62464
Luxembourg (L) 40 4078 40 2085
Netherlands (NL) 0800 400 1010 0800 400 1040
Norway (N) 66-817 000 66-817 157
Portugal (P) 2185 00144 2185 00165
Spain (E) 902 52 77 70 91 410 4078
Sweden (S) 08-7501850 08-7501810
Switzerland (CH) 01-8471644 01-8471650
Czech. Rep. (CZ) 02-6130 0446 02-6130 0514
Hungary (H) 76 511 803 76 511 809
Poland (PL) 0800-118922 022-8771260
Turkey (TR) 0212-335 06 71 0212-346 00 40
Blaupunkt GmbH,
Robert-Bosch-Straße 200,
D-31139 Hildesheim
03/07 CM-AS/SCS1 (GB)
8 622 405 394
84
Loading...