Page 1
VEHICLE SECURITY
SYSTEM S01/S02
S01
Operating and Installation Instructions
S02
Enjoy it.
Page 2
CAUTIONS
Safety Notes
This vehicle security system has been manufactured according to established safety
guidelines. However, dangers may still occur
if the safety notes in this manual is not observed. This manual is intended to familiarize
the user with the vehicle security system’s
important functions. Read this carefully, prior
to using the vehicle security system. Keep
this manual in an easily accessible location.
In addition, do observe the instructions of
the devices used in conjunction with this
vehicle security system.
Attentions
•
Keep the device in a dry and well-ventilated environment.
•
Do not drop the device or subject it to
physical shock.
•
Improper use or replacement of the
battery may cause in explosion hazard.
Replace with the equivalent type only.
•
The vehicle security system is a
complicated technical device implying
connection to the car circuits related to
engine operation. It is strongly advised to
have a professional car mechanic installing
the system.
This manual may be updated from time to
time without any notice.
Disclaimer
In no event shall Blaupunkt be liable for any
direct, indirect, punitive, incidental, special
consequential damages to property or life
and whatsoever arising out of or connected
with the use or misuse of our products.
USA & CANADA: This product is not intended
for sale in the United States and Canada. If
purchased in the U.S. or Canada, this product
is purchased on as-is basis. No warranty,
whether expressed or implied is provided in
the U.S. or Canada.
STRUCTURE
1
2
4
3
S01 S02
Function
Arm
Disarm
Panic
Trunk Release
Beep Sound (Silent)
Auto Relock (Default: Activated)
Foot Brake Lock (Default: Activated)
Valet Mode (Default: Activated)
Exit Delay Time (5 & 30Sec) (Default: Activated)
SPECIFICATIONS
Remote Arm, Disarm and Panic
•
Remote Silent Arm and Disarm
•
Remote Boot Release
•
Beep Sound (Remote Selectable)
•
Auto Relocking / Auto Rearming (Remote
•
Selectable)
Foot Brake Lock (Remote Selectable)
•
Valet Mode (Remote Selectable)
•
Door Not Closed Warning (Remote
•
Selectable)
Button
Button 1
Button 2
Button 3
Hold Button 2 /4
Button 1 & 2
Hold Button 1
Hold Button 2
Hold Button 1 & 2
Hold Button 3
Exit Delay Time 5 or 30 sec. (Remote
•
Selectable)
Door Open Detection
•
2 Ports Three Wire Dual Zone Shock
•
Sensor
Passive Immobilizer
•
Code Learning Technology
•
Ignition Status
ON (Deactivate)
ON (Deactivate)
ON (Deactivate)
ON (Deactivate)
1
2
4
3
OFF
OFF
OFF
OFF
OFF
1
2
Page 3
FUNCTIONS
1. Arm (Lock)
Press Button 1 to arm.
•
The central lock will be lock, alarm will
•
beep once, hazard light ashes and LED
light will turn on.
The immobilizer will function if the
•
ignition is turned ON.
2. Disarm (Unlock)
Press Button 2 to disarm.
•
The central lock will be unlocked and
•
alarm will beep twice.
Hazard light ashes twice and LED light
•
will turn o.
3. Beep Sound (Remote Selection)
Press Button 1 and 2 simultaneously to
•
disable Beep sound, hazard light will
ash twice.
Repeat the same step to enable the
•
Beep sound.
The alarm will beep and hazard light
•
will ash.
4. Panic
Press Button 4 to trigger the alarm and
•
hazard light for approx. 45 sec. instantly
in case of emergency.
Press buttons other than Button 4 to turn
•
o the alarm, alarm system will remain
armed and locked.
5. Auto Relock/ Auto Rearm
(Remote Selection)
After 30 seconds of disarming the alarm
•
system and no doors are being open, the
system will automatically relock / rearm
the vehicle.
If the central locking was accidentally
•
unlocked after 15 sec. second alarm will
beep and hazard light ashes, indicating
the system will be rearmed and the door
will be relocked in another 15 sec.
To disable this function, turn on the
•
ignition, press and hold Button 1 for
2 sec., the alarm will beep twice and
hazard light ashes.
Repeat the same step to enable this
•
function again, alarm will beep once and
hazard light ashes.
6. Passive Immobilizer
This function will be activated either
•
after the ignition is turned o for 60 sec.
at disarm mode or 60 sec. passed after
Button 2 is pressed.
The passive immobilizer sends out signal
•
to stop the electronic start/ ignition
circuit in order to immobilize the vehicle.
The blinking LED indicates the function
is enabled.
To Cancel the passive immobilizer, press
•
Button 2; the LED will stop blinking
indicating the function is disabled.
Note : The auto-relock function will override passive immobilizer function.
7. Doors/ Boot/ Bonnet Zone Protection
The alarm will be triggered if any zones
•
are opened while the alarm status is in
armed mode.
The siren will last for 45 sec. and 5 sec.
•
break, every time the system check for
the zone status.
Upon completion of 3 zone status check-
•
ing, the violated port is ignored and the
system will be rearmed.
FUNCTIONS
8. Key on Trigger Zone
•
The alarm will be triggered if the alarm is
in arm mode and the ignition is ON.
•
The siren will continue for 45 sec. before
it takes 5 sec. to check on the ignition
status, the siren will continue if alarm is
still in arm mode while ignition is ON.
9. Manual Override System
•
To set o the alarm system without
using a the remote in case of missing/
malfunction remote, turn on the ignition
and press the Reset switch once.
10. Ignition / Starter Disable (External
Heavy Duty 30A Relay)
•
When the alarm system is in arm mode
and ignition is ON, the system will halt
the ignition (subject to relay connection)
and the alarm will be triggered. This will
immobilize the vehicle to prevent car
from being stolen.
11. 3 Independent Triggering Zones
with Memory
•
There are sensors on the doors/ bonnet/
boot & ignition key zones.
•
The alarm will beep 3 times after the
alarm is disarmed, indicating doors/
bonnet/ boot zone is triggered; 4 times
indicate sensor, 5 times indicate ignition
key zone triggered.
•
The memory will automatically be
erased when the ignition is turned on in
disarm mode.
12. LED Indicator shows the Status of
the Security System
A dashboard mounted red arm and
•
memory LED will light up to indicate
when the alarm system is arm, disarm,
triggered.
13. Valet Mode (Remote Selection)
To turn on the Valet Mode, then the
•
ignition ON, press Button 1 and 2 for
hold for 2 sec., the alarm will beep once
and hazard light ashes, the arm LED
ashes too.
The alarm system will be disabled when
•
in valet mode (Not include Central Lock
System).
To return to normal mode, repeat the
•
same steps again while the ignition
is ON.
14. Door Open Detection
In disarm mode, when the alarm system
•
detects opened doors and the ignition is
ON, the hazard light ashes.
The hazard light will stop ashing when
•
the doors are closed.
15. Opened Door Warning (Remote
Selection)
When door lock mode is activated, alarm
•
will beep and hazard light ashes when
the doors are opened.
After 30 sec., the alarm will be trigger.
•
To disable this function, follow the Exit
•
Delay Time Selection.
3
4
Page 4
FUNCTIONS
16. Exit Delay Time (Remote Selection)
Exit delay time (5/ 30 sec.) can be select-
•
ed by the remote control.
For exit delay time 5 sec., turn ON the
•
ignition, then press and hold the Button
3, the alarm will beep twice and hazard
light ashes.
When select exit delay time 5 sec.,
•
opened door warning function will be
disabled.
Repeat the same procedure again for the
•
exit delay time to 30sec., the alarm will
beep once and hazard light ashes.
17. Trunk Release Activation by Remote
(Optional)
Press and hold Button 2 or 4 (open trunk
•
signal output is required).
The alarm system will automatically
•
disarm each time the trunk is opened.
18. 3 Wire Dual Zone Shock Sensor
(TWDZ) Optional
If the vehicle is hit by light impact, the
a)
alarm will release a warning beep.
If the vehicle is hit by high impact, the
b)
alarm will release the siren for 45 sec.
before it stops.
19. Transmitter Pairing Process
Turn the ignition ON & OFF, repeat the
a)
steps 5 times, then keep the ignition ON.
Press any button on the remote, LED
b)
light will be on without ashes. Press any
button again, the LED light will be o,
indicating pairing successful.
The LED will blink again as a sign for
c)
ready learning once more. Repeat step
b. again for up to 6 pairing. A maximum
of 10 sec. is allowed for each complete
learning at one time.
After completed pairing, turn o the
d)
ignition to exit the pairing process.
TROUBLESHOOTING
If any of the following problem occur, please resort to Troubleshooting for the possible
solutions. Consult Blaupunkt authorized dealer if problem persist.
Problems
Remote does not work
System will not arm
Possible Causes
Remote is not proggrammed
or not pair.
Weak or stale battery.
Power supply problem.
Remote is not functioning.
5 6
Solutions
Program remote and check
the wire connection.
Replace with a new and
equivalent type of battery.
Check +12V & ground (earth)
at the system module.
Check the battery level of
the remote.
WIRING DIAGRAM
Shock Sensor (Optional)
LED Status Indicator
Reset Switch
Ultra Sonic Sensor
(Optional)
Hazard Light
Door / Bonnet / Boot
9 Brown
7 Orange
1 White / Yellow
2 White / Yellow
3 Green
4 Blue
Central Locking
Yellow
Ignition Key (ON)
12 White
13 Brown / White
5 Black
6 Red
Antenna
Yellow
Front View
Boot Release Module
(Optional)
Red
Blue
Yellow
Blue
Green
10 Green/ Black
Brake Light
Foot Brake Switch
Existing Low Current Solenoid
Feed Wire (+12V DC, Key “ON” only)
To Start Solenoid To Ignition Switch
Black Black
Orange / White
(Optional)
11 Orange / White
1
2
3
4
5
6
7
8
9
10
11
12
13
:
Hazard Light
:
Hazard Light
:
Lock (Relay)
:
Unlock (Relay)
:
Ground
:
+12V DC
:
Door Switch
:
(-) Output
:
Siren
:
Foot Brake
:
Key On
:
Unlock (-)
:
Lock (-)
8 Grey
+ 12VDC
+ 12VDC
Page 5
Designed and engineered by Blaupunkt Competence Centre
VSS S01
1 521 19 007 23 01
VSS S02
1 521 19 008 23 01
Loading...