Blaupunkt RX+ 35e Instruction Manual

RX+ 35e

Digitalradio mit USB/SD
Digital Radio with USB/SD

RX+ 35e

2

RX+ 35e

3

RX+ 35e

4

RX+ 35e

5

RX+ 35e

6

RX+ 35e

7

RX+ 35e

8

RX+ 35e

9

RX+ 35e

10

RX+ 35e

11

RX+ 35e

12

RX+ 35e

13

RX+ 35e

14

RX+ 35e

15

RX+ 35e

16

08:00

31-05-2013

Friday

08:00

Digital Radio

Blaupunkt

RX+ 35e

17

RX+ 35e

18

RX+ 35e

19

RX+ 35e

20

RX+ 35e

21

RX+ 35e

22

BBC Radio4 3

RX+ 35e

23

RX+ 35e

24

RX+ 35e

25

RX+ 35e

26

RX+ 35e

27

100.80MHz 3

RX+ 35e

28

Signal Strength

RSSI

RX+ 35e

29

RX+ 35e

30

RX+ 35e

31

RX+ 35e

32

RX+ 35e

33

RX+ 35e

34

RX+ 35e

35

RX+ 35e

36

RX+ 35e

37

RX+ 35e

38

RX+ 35e

39

RX+ 35e

40

RX+ 35e

41

RX+ 35e

42

Important Safety Instructions

Important Safety Instructions

Caution:

To reduce the risk of electric shock, do not dismantle the product and do not expose the
apparatus to rain or moisture. No user-serviceable parts inside. Refer servicing to
qualified personnel only.

Explanation of Graphical Symbols:

To achieve the utmost in enjoyment and performance, and in order to become familiar with its
features, please read this manual carefully before attempting to operate this product. This will
assure you years of trouble free performance and listening pleasure.

Important Notes

This safety and operating instruction should be retained for future reference.
The apparatus should not be exposed to dripping or splashing or placed in a humid

atmosphere such as a bathroom.

¡Do not install the product in the following areas:
¡Places exposed to direct sunlight or close to radiators.
¡On top of other stereo equipment that radiate too much heat.
¡Blocking ventilation or in a dusty area.
¡Areas where there is constant vibration.
¡Humid or moist places.
Do not place near candles or other naked flames.
Operate the product only as instructed in this manual.
Before turning on the power for the first time, make sure the power adaptor is properly

connected.

Plug-in the USB stick directly or use an USB-extension cable which is not longer than 25 cm.

For safety reasons, do not remove any covers or attempt to gain access to the inside of the
product. Refer any servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user
serviceable par ts inside. Refer all servicing to qualified service personnel.

The lightning flash within an equilateral triangle is intended to aler t you to the
presence of uninsulated dangerous voltage within the product's enclosure that
may be of sufficient magnitude to constitute an electric shock to a person or
persons.

The exclamation point within an equilateral triangle is intended to alert you to
the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.

RX+ 35e

Conformity

Model number: RX+ 35e
Description:
Brand name: Blaupunkt
Responsible party: M3 Electronic GmbH
Gutenbergstrasse 5, D-65830 Kriftel. Germany
Hereby, Blaupunkt Competence Center Audio M3 Electronic GmbH, declares that this Class 1
equipment is in compliance with the essential requirement and other relevant provisions of
Directive 1999/5/EC.
Letter of conformity can be obtained from [e-mail].

Safety Instructions

Digital Radio with USB/SD

Read Instructions - All the safety and operating instructions must be read before
the product is operated.
Retain Instructions - The safety and operating instructions should be kept with the
product for future reference.
Heed warnings - All warnings on the product and in the operating instructions
should be adhered to.

Follow instructions - All operating and users’ instructions should be followed.
Installation - Install in accordance with the manufacturer's instructions.
Power sources - This product should be operated only from the type of power

source indicated by the marking adjacent to the power cord entry. If you are not
sure of the type of power supply to your home, consult your product dealer or local
power company.
Grounding or polarization - the product is not required to be grounded. Ensure
that the plug is fully inser ted into the wall outlet or extension cord receptacle to
prevent blade or pin exposure. Some versions of the product are equipped with a
power cord fitted with a polarized alternating line plug (a plug having one blade
wider than the other). This plug will fit onto the power outlet only one way. This is a
safety feature. If you are unable to inser t the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug. When using
an extension power-supply cord or a power-supply cord other than that supplied
with the appliance, it should be fitted with the appropriate molded plugs and carry
safety approval appropriate to the country of use.
Power cord protection - Power-supply cords should be routed so that they are not
likely to be walked on, kinked or pinched by items placed on or against them,
paying particular attention to cords from plugs, receptacles and the point where
they exit from the product.
Overloading - Do not overload wall outlets, extension cords, or multiple sockets, as
this can result in a risk of fire or electric shock.
Ventilation - The product must be properly ventilated. Do not place the product on
a bed, sofa, or other similar surface. Do not cover the product with any items such as
tablecloths, newspapers, etc.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

43

RX+ 35e

Heat - The product should be situated away from heat sources such as radiators,

heat registers, stoves, or other products, including amplifiers that produce heat. No
naked flame sources, such as lighted candles, should be placed on the apparatus.
Water and moisture - To reduce the risk of fire or electric shock, do not expose the
product to train, dripping, splashing or excessive moisture such as in a sauna or
bathroom. Do not use this product near water, for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool (or
similar).
Object and Liquid Entry - Never push objects of any kind into this product through
openings, as they may touch dangerous voltage points or short-circuit par ts that
could result in a fire or electric shock. Never spill liquid of any kind on the product.
Do not place any object containing liquid on top of the product.
Cleaning - Unplug the product from the wall outlet before cleaning. Dust in the
woofer may be cleaned with a dry cloth. If you wish to use an aerosol cleaning spray,
do not spray directly on the cabinet; spray onto the cloth. Be careful not to damage
the drive units.
Attachments - Do not use attachments not recommended by the product
manufacturer, as they may cause hazards.
Accessories - Do not place this product on an unstable cart, stand, tripod, bracket
or table. The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions and should use a mounting
accessory recommended by the manufacturer.
Moving the product - A product and cart combination should be moved with care.
Quick stops, excessive force and uneven surfaces may cause the product and cart
combination to overturn.
Unused periods - The power cord of the appliance should be unplugged from the
outlet during lightning storms or when the apparatus is left unused for a long
period of time.
Servicing - Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified ser vice personnel.
Please remove the power plug form the main power source or wall power source
when not in use. When plugged in to a power source, the system is in standby mode,
so the power is not entirely cut off.
Replacement parts - When replacement parts are required, ensure that the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
Mains fuses - For continued protection against fire hazard, use fuses only of the
correct type and rating. The correct fuse specification for each voltage range is
marked on the product.
Do not turn up the volume while listening to a section with very low level inputs or
no audio signals. If you do, the speaker may be damaged when a peak level section
is suddenly played.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

44

RX+ 35e

45

The only means of completely disconnecting the product from the power supply is
by removing the power cord from the wall outlet or the product. The wall outlet or
the power cord entry to the product must remain freely accessible at all times while
the product is in use.
Try to install the product near a wall socket or extension cord and shall be easily
accessible.
The highest environmental temperature suitable for this product is 35°C.
ESD hints - The normal function of the product may be disturbed by strong Electro­Magnetic Interference. If so, simply reset the product to resume normal operation
by following the instruction manual. In case the function could not resume, please
use the product in other location.

Battery

24.

25.

26.

27.

28.

The batteries must not be exposed to excessive heat such as sunshine, fire or
the like.
The batteries should be drawn to the environmental aspects of battery
disposal.
Batter y usage CAUTION-to prevent battery leakage which may result in body
injuries, property damage, or damage to the apparatus:
Install all batteries correctly, + and – as marked on the apparatus.
Do not mix batteries (old and new or carbon and alkaline, etc.)
Remove batteries when the unit is not used for a long time.

1).

2).

3).

ERP2 (Energy Related Products) note

This product with ecodesign complies with the stage 2 requirements of Commission
Regulation (EC) NO. 1275/2008 implementing Directive 2009/125/EC regard to standby
and off mode electric power consumption of electronic household and office equipment.
After 15 minutes without any audio input, the device will automatically switch into
standby mode. Follow up the instruction manual to resume the operation.

This device is equipped with an energy saving mode: if no signal is given during 15
minutes the device will switch automatically into standby mode in order to save energy
(ERP 2 standard). Please note that low volume setting in the audio source may be
recognized as “no audio signal”: this will affect the capability of signal detection from the
device and can also originate an automatic switch into standby mode. If this happens
please reactivate the audio signal transmission or increase the volume setting on the
audio source player (MP3 player, etc.), in order to resume playback. Please contact the
local service center if the problem remains.

Warning

This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.

Important note:

RX+ 35e

46

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

Never use the device unsuper vised! Switch off the device whenever you are not
using it, even if this only for a shor t while.
The appliance is not intended to be operated by means of an external timer or
separate remote control system.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Before operating this system, check the voltage of this system to see if it is identical
to the voltage of your local power supply.
The unit should not be impeded by covering the ventilation opening with items
such as newspaper, table-cloths, curtains etc. Make sure that there are at least 20
cm of space above and at least 5 cm of space on each side of the unit.
The apparatus must not be exposed to dripping or splashing and that objects filled
with liquids, such as vases, must not be placed on the apparatus.
To prevent fire or shock hazard, do not expose this equipment to hot places, rain,
moisture or dust.
Do not locate this unit near any water sources e.g. taps, bathtubs, washing
machines or swimming pools. Ensure that you place the unit on a dry, stable
surface.
Do not place this unit close to a strong magnetic field.
Do not place the unit on a amplifier or receiver.
Do not place this unit in a damp area as the moisture will affect the life of electric
components.
If the system is brought directly from a cold to a warm location, or is placed in a very
damp room, moisture may condense on the lens inside the player. If this occurs, the
system will not operate properly. Please leave the system turned on for about an
hour until the moisture evaporates.
Do not attempt to clean the unit with chemical solvents as this might damage the
finish. Wipe with a clean, dry or slightly damp cloth.
When removing the power plug from the wall outlet, always pull directly on the
plug, never pull on the cord.
Depending on the electromagnetic waves used by a television broadcast, if a TV is
turned on near this unit while it is also on, lines might appear on the TV screen.
Neither this unit nor the TV is malfunctioning. If you see such lines, keep this unit
well away from the TV set.
The mains plug is used as the disconnect device, the disconnect device must
remain readily operable.

1.

2.

3.

4.

5.

Front Panel

Rear Panel

DISPLAY SCREEN

INFORMATION

SLEEP/ STANDBY

MENU

NEXT

ENTER / < STOP

EARPHONE PORT
VOLUME KNOB

SD CARD PORT

PRESET/ PLAY/PAUSE

USB PORT

SOURCE

PREVIOUS

SPEAKER

TELESCOPIC ANTENNA

POWER SUPPLY INPUT

RX+ 35e

47

Switching on for the first time

1. Connect the mains plug to a wall outlet.

2. Extend the telescopic aerial as far as it can go.
(Note: The quality of the DAB/FM reception will be influenced by the positioning of
the aerial.)

08:00

31-05-2013

3. When you turn on the unit, it will first show the information of our brand. Then on
the standby mode it will display the information of time & date. The time and date is
updated automatically when you turn on to DAB mode.
(Note: if the DAB signal is weak, the unit system may be unable to scan stations or
find the DAB signal and the time and date are not activated by DAB mode. Please
place the unit on a position with strong DAB signal. You can also adjust the time and
date manually, please refer to Page 55 for more operation details.)

4. Press and hold the SLEEP/ STANDBY button to turn the unit to the normal
playback status.

General Operation

Standby mode

Press and hold the SLEEP/ STANDBY button to switch the radio into standby mode.
To resume normal operation press and hold this button again.
Note: When you switch on the unit from standby the last used mode will resume.

Mode Selection

The SOURCE button is for mode selection, there are four modes: USB, SD, DAB and FM,
press this button repeatedly to cycle through and choose the mode you want.

Volume Control

The volume knob is to control the volume. To increase volume, adjust the knob to
clockwise direction. To decrease volume, adjust the knob to anticlockwise direction.

Friday

08:00

Digital Radio

Blaupunkt

Opening screen:

RX+ 35e

48

DAB Operation

Press SOURCE button repeatedly to switch to the DAB mode.
During scan mode, the LCD will display a slide bar that indicates the progress of the scan,
and the amount of radio stations that have been found so far. Once the scan finished, the
radio will play the first alphanumeric station.

Station selection

To listen to the stations that have been found use the PREV/NEXT buttons to cycle through.
Each time you press these buttons the unit will skip to the previous or next stored station.
Press the ENTER button to activate the station.

Station Scan mode

1. Press the MENU button, then use PREV or NEXT button to find <Station Scan>, press
ENTER button.

2. There are several scan modes: Local Scan, Full Scan, Manual Tune.

Local Scan: search the local DAB channels.
Full Scan: search all DAB channels.

3. If you choose Local Scan or Full Scan, press ENTER to confirm and it will start scanning.

4. Use the PREV or NEXT button to select Manual Tune, and press ENTER.

5. Use the PREV or NEXT button to cycle through the DAB channels, which are

numbered from 5A to 13F.

6. Now press the ENTER button to enter the ensemble/multiplex you want to search.

The screen will display the first station found in the ensemble/multiplex. Press
ENTER button and the first station of the ensemble starts playing.

7. To see which stations are present in the found ensemble/multiplex, just press either

PREV/NEXT buttons. When you have located a station that you would like to listen to,
just press the ENTER button to activate it.

Storing station presets

It is possible to store up to 10 of your favorite stations. This will enable you to access your
favorite stations quickly & easily.
To store a preset station, you must first be listening to the station that you would like to save.

1. Press the PRESET button, the screen will show “ Preset X empty” (if any stations have

been preset before, it will show the station name e.g. “BBC Radio4 3")

2. Press the PREV or NEXT button to select the number you want to store.

3.

RX+ 35e

To confirm preset, press and hold the ENTER button, then it will show "Preset X
saved". For example, if you are listening to BBC World which you want to preset in

no. 5 station: first, press PRESET button, it might show "Preset 1 empty" as there is
no preset station. Then, press PREV or NEXT button to find "Preset 5 empty" (if this
no. 5 has already a preset a station, you can still preset one new station on it). Press
and hold ENTER button, then it will show "Preset 5 saved".

49

Recalling a station preset

To recall a preset station, press the PRESET button on the unit, it will display the information
like following:

The name represents the station, and the NO.3 represents the preseted no.. Press the PREV/
NEXT button to scroll through the previous or next preset station. If the no. 4 does not have
any preset station, it will show "Preset 4 empty"
If you want to recall the no. 2 preset station, press PREV/NEXT button to select the second
preset station, then press ENTER button to confirm recalling.

BBC Radio4 3

Ensemble/Multiplex (Group name)

A multiplex/ensemble is a collection of radio stations that are bundled and transmitted on
one frequency. There are national and local multiplexes. Local ones contain stations that
are specific to that area e.g. MXR West.
NOTE: DAB (in opposition to traditional FM) groups together several radio stations and
transmits them in one frequency.

Bit rate

This displays the type of broadcast which you are receiving (e.g. mono or stereo) and which
bit rate is being used.

DLS (Dynamic Label Segment)

Dynamic label segment is a scrolling message that the broadcaster may include in his
transmissions. This message usually includes information like program details.

Program Type

This describes the “style” or “genre” of music that is being broadcast e.g. “Rock” or
“Classical”.

Display modes

Every time you press the “INFO” button, the display will cycle through the following display
modes: (the information is displayed on the lower segment of the LCD display):

RX+ 35e

50

Prune Station

This function can delete a station from the stored station list.

1. Press the MENU button.

2. Use the PREV or NEXT button to find <Main Menu>, then press ENTER button.

3. Press either PREV or NEXT button to find <Prune Station>. There is indication

“Press ‘ENTER’ to Prune station” .

4. If you want to prune the station, do as the indication.

Station Order

This function allows you to change the order of the stored stations.

1. Press the MENU button.

2. Use either PREV or NEXT button to find <Main Menu>, then press the ENTER

button.

3. Press either PREV or NEXT button to find <Station Order>.

4. Use the PREV or NEXT button to choose between Multiplex, Alphanumeric and

Active.

5. Press ENTER to save the setting.

DRC ( Dynamic Range Control)

This allows the radio to reduce the dynamic range of the audio signal. The purpose
is to adapt the dynamic range of the audio signal to a noisy listening environment.
NOTE: this option may not be available in some DAB stations.

1. Press the MENU button. When the <Station scan> option appears press either
PREV or NEXT button to find <Main Menu>. Press ENTER button.

2. Use PREV or NEXT button to find <DRC> and then press the ENTER button.

3. Choose between DRC off, DRC low and DRC high.

4. Press ENTER to save the setting.

RX+ 35e

51

100.80MHz 3

FM Operation

Press the SOURCE button repeatedly to switch to FM.

RX+ 35e

Scanning for stations

1. You can scan up or down the frequenc y range manually by pressing the PREV/NEXT

buttons to increase or decrease the frequency in 0.05 MHz steps.

2. You can scan up or down from the current frequency range automatically: press and

hold the PREV or NEXT button to scan backward or scan forward from the current
frequency. Once a station is found, it will stop and play that station.

Storing station presets

It is possible to store up to 10 of your favorite stations. This will enable you to access
quickly & easily to your favorite stations.

To store a preset station you must first be listening to the station that you would like to
save. Then press the PRESET button: the screen will show " Preset X empty" (if any station
has been preset before, it will show the station frequency e.g. "100.80MHz 3").
Then you can press the PREV or NEXT button to select the number which you want to
store. To confirm preset, press and hold the ENTER button: it will show "Preset X saved".

For example, if you are listening to 88.5MHz which you want to preset in no. 5 station, you
can press PRESET button, it might show "Preset 1 empty " as there is no preset station.
Use the PREV or NEXT button to find "Preset 5 empty" (if the no. 5 has a preset station,
you can still preset one new station there). Press and hold ENTER button: it will show
"Preset 5 saved".

Recalling a station preset

To recall a preset station, press the PRESET button on the unit and it will display
information like following:

The frequency represents the station, and the no. 3 represents the preset number.
Press the PREV/NEXT button to scroll through the previous or next preset station.
If the no. 4 has not any preset station, it will show as "Preset 4 empty".
If you want to recall the no. 2 preset station, press PREV/NEXT button to select the
second preset station, then press ENTER button to confirm recalling.

Audio Mode (Stereo/Mono)

Indicates if the broadcast is in Stereo or in Mono audio mode.
To specify that a station can be only played in mono or that it can be played in stereo or
mono:

1. Press the MENU button and find <Audio Setting>.

2. Press ENTER button. Use the PREV or NEXT button to cycle through the 2 options:

<Mono only> or <Stereo or mono>.

3. Press ENTER button to confirm.

Mono only: plays all stations in mono regardless of the availability of a stereo signal.
Stereo or mono: stations might be played in mono or in stereo.

52

SW Version

Follow the below steps to scan the version of this unit.
SD mode):

1. Press the MENU button. Use the PREV/NEXT button to find <Main Menu> and press
the ENTER button.

2. Use the PREV/NEXT button to choose <SW Version> and press ENTER button to
review the version.

(this function does not work in USB or

Signal Strength

RSSI

Language

Follow the below steps to set the language of this unit.
or SD mode):

1. Press the MENU button. Use the PREV/NEXT button to find <Main Menu>, press the

ENTER button.

2. Use the PREV/NEXT button to choose <Language> and press the ENTER button.

3. Choose English or Deutsch by PREV/NEXT button and press ENTER button to confirm.

(this function does not work in USB

Advanced operation

Factory Reset

Follow the below steps to restore to factory settings (this function does not work in USB or
SD mode):

1. Press the button. Use the / button to find < >, then press

the ENTER button.

2. Use PREV/NEXT button to choose <Factory Reset>, then press the ENTER button.

3. Indication "Press 'INFO' To confirm Reset" will be shown on the screen. If you want

to reset, press INFO button to start the reset process.
NOTE: once the reset has taken place, you will lose all your stored presets both DAB+ and FM,
and the internal DAB registry.

MENU PREV NEXT Main Menu

Program Type

"Classical". If no Program Type has been set by the broadcaster then <No PTY> will be
displayed.

This describes the "style" or "genre" of music that is being broadcast e.g. "Rock" or

Radio Text

about the current program. If Radio Text information is not available, then the display will
show <No Radio Text>.

Like in DAB mode the broadcaster can include a scrolling text that displays information

Display modes

Every time you press the “INFO” button, the display will cycle through the following display
modes:

RX+ 35e

53

Play/Pause

During playback, press the PLAY/PAUSE button once to pause playback and press it
again to resume playback.

Stop

During playback, press the STOP button once to stop playback and resume playback by
pressing the PLAY/PAUSE button.

Skipping Tracks

Press the NEXT button to listen to the next track on the USB/SD mode. Press the PREV
button to listen to the previous track.

Repeat / Random playback

During playback the tracks can be played repeatedly or in a random order.
Press INFO button repeatedly to choose between the several options:
Random: the tracks will be played in a random order which is different from the original
one.

Intro: it will play the first 10 seconds of each track.
Repeat One: will repeat playing the current track.
Repeat All: will repeat playing all tracks. Note:

USB/SD Operation

1.

2. Press the SOURCE button to cycle through and enter to the desired mode. The unit
will detect the device automatically. If the USB or SD devices have not been
connected then "NO USB" or "NO SD" will be shown in the screen. Then you can
connect the USB or SD card. If one of these devices is found, the radio will start
playing automatically.

3. In this external audio mode you can use the function like skip tracks, pause or stop
playback.
Remark: Plug-in the USB stick directly or use an USB-extension cable which is not longer
than 25 cm.

Connect the USB or SD card to the USB or SD Card port on the front panel of the radio.

Note:

1. USB extension cable shall have a max. length of 0,25 m.

2. Depending on the amount of data and media speed, it may take longer for system to

read the contents from the media device. In some cases, reading time may be as long
as 60 seconds. This is not a malfunction.

3. Depending on the content some files may not be played or displayed even when they

are in a supported format.

4. The max. supported capacity of USB devices is 32GB and SD max. capacity is 16GB.

Warning: connect your USB device directly to the USB port of the radio. Using an extension
cable is not recommended and may cause interference and failure of data transfer.

RX+ 35e

54

RX+ 35e

Basic Setup

In standby mode press MENU button to set time, date, alarms and language.
Each time that you press this button, it will turn to each setup page.

Time Setup (only in standby mode)

In standby mode you can make time setting.

1. Press and hold the SLEEP/ button to enter to the Standby mode.

2. Press MENU button to enter Time Setup interface. In this status, you can see

the hour digit flashing. Then you can adjust the Volume knob to set the correct hour
time: rotate the knob in clockwise direction to increase numbers, and in opposite
direction to decrease.

3. After setting the correct hour time, press ENTER button to confirm. Then the minute

digits will flash and you can set the minute time. The setting method is the same
as the hour setting.

4. Press ENTER button to confirm the time setup.

After time setting, you can make date setting.
Note: when you press MENU button, and select "Time Auto update" to ON, the
clock time will update automatically when the DAB signal is available; if you select
OFF, the unit will show the manual time setting.

5. After you press the ENTER button to confirm time setup, you can see the year time

digits flashing, and you can adjust it with the Volume knob.
The method is the same as for Hour setting.

6. After setting the correct year, press ENTER button to confirm. Then the month digits

will flash and you can set the month time. The setting method is the same as the
Hour setting. Press ENTER button to confirm.
Then you can set the day: the method is the same as above operation.

7. Press ENTER button to confirm the date setup.

Alarm Setup (only in standby mode)

In standby mode, you can make alarms setting. The alarms will turn on the unit in the
mode that you have selected.

1. Press the MENU button repeatedly to enter in the Alarm Setup interface. There are

two alarms.

2. In the alarm setting interface, you can see "Alarm 1 status", and option ON will flash:

adjust the Volume knob in any direction to choose ON or OFF and press ENTER
button to confirm your choice.

3. Then you are required to set the alarm time: first the hour digits flash and the setting

method is the same as in Time Setup.

4. After setting, press ENTER button to confirm. Afterwards you can set the frequency

of Alarm. There are several choices: Once, Daily, Weekdays and Weekends. Adjust
the volume knob to set your choice and press ENTER button to confirm.

5. Press ENTER button and you can set the mode which the unit will be on when the

alarm time is activated. You can choose Buzzer (audible signal), FM, DAB, SD or USB.
If you choose FM, DAB, SD or USB you have to set the volume: the Volume setup
indication appears. Use the Volume knob to adjust the desired volume level and
press ENTER button to confirm.

55

RX+ 35e

6. If you choose the alarm mode FM, DAB, SD or USB the unit will

turn on to the corresponding mode and will start playback in that setting volume.
Note: after setting, the alarm logo will be shown on the screen. Then you can set the
second alarm: press the MENU button repeatedly to the "Alarm 2 Status". The method of
Alarm 2 setting is the same as Alarm 1.

Deactivate the alarm

To deactivate the alarm please follow the below steps:

1. Press the MENU button repeatedly to enter Alarm Setup inter face.

2. You can see "Alarm 1 status": adjust the Volume knob to choose OFF and press

ENTER button to confirm.

Note: if you set the same time for Alarm 1 and Alarm 2 the Alarm 1 is the priority ring.

Snooze Time

When you choose BUZZER you will hear an audible signal and you can activate the
Snooze mode to delay the alarm for 3 minutes. When the alarm is ringing, adjust the
volume knob to any direction: the audible signal will be off and the alarm will repeat after
3 minutes. You can delay it for another 3 minutes by adjusting the volume knob after the
alarm starts ringing. To cancel the alarm: press the ENTER button once or press and hold
the SLEEP/ button.
NOTE: during the delayed 3 minutes, if you press and hold the SLEEP/ button to switch
between standby or normal playback mode, the alarm will be canceled.

Alarm in normal playback status

After setting a alarm with Buzzer mode, you can turn the unit to the normal playback
status. When the alarm is ringing and the normal playback pauses, then you can adjust the
volume knob to delay 3 minutes or you can press the ENTER button to cancel the alarm.

Language Setup

You can set the language in Standby mode:

1. Press the MENU button repeatedly to the Language setup interface.

2. You can see Language: English. Adjust the Volume knob in any direction to choose

between English or Deutsch.

3. Press ENTER button to confirm.

Sleep time Setup (Not in standby mode)

This setting is to set the time when the unit will switch automatically in the standby status.

1. Press the SLEEP/ button repeatedly to choose between different time periods:

sleep off, 10 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, 90 minutes
or 120 minutes.

2. If you want to select 10 minutes sleep time just use the SLEEP/ button to c ycle

through this option: do not touch any buttons for a few seconds, it will return to the
normal playing status and this setting will be saved.

3. When the set time is reached, the unit will switch to the standby mode.

4. To resume normal playback status, press and hold SLEEP/ button.

56

After using your unit.

The sound is weak or has
poor quality

Other devices, e.g. a television,
are interfering with reception.

Move the unit further away
from these devices.

RX+ 35e

57

DAB+:

174.928~239.200 MHz

FM:

Standby Power Consumption:............................................................................................< 1 Watt

Max. Power Consumption:....................................................................................................20 Watt

POWER INPUT:

DC 12V

RX+ 35e

87.5~108 MHz

58

This symbol on the product or in the instructions means that your electrical and electronic
equipment should be disposed at the end of its life separately from your household waste.
There are separate collection systems for recycling in the EU.
For more information, please contact the local authority or your retailer where you purchased
the product.

All rights reserved by Blaupunkt Competence Center Audio M3 Electronic GmbH. This
material may be reproduced, copied or distributed for personal use only.

59

RX+ 35e