Blaupunkt Orlando-MP-46 Owners Manual
Orlando MP46 7 646 480 310
Radio CD MP3 WMA
0QFSBUJOH JOTUSVDUJPOT
1 32
12
4
5
6 7
11
8
9
10
2
Controls
1 On/Off button
Short press: Mutes the device.
Long press: Switches the device off.
2
button to open the fl ip-release con-
trol panel.
3 Volume control
4 SOURCE button to switch sources be-
tween radio, CD, CD changer (if connected) and AUX.
5 AUDIO button to adjust bass, treble,
middle, subout, balance and fader.
Switching X-BASS on/off and adjusting it.
Selects an equalizer presetting.
6 BND•TS button
8 DISPL
button
Short press: Briefl y displays alternative
display contents (e.g. time).
Long press: Changes display contents.
9 MENU button
Short press: Calls up the menu for basic settings.
Long press: Starts the Scan function.
: Arrow buttons
; Buttons 1 - 6
<
button (Eject) for removing a CD
from the device.
Short press: Selects the FM memory
banks and the MW and LW wavebands.
Long press: Starts the Travelstore function.
TRA•RDS button
7
Short press: Switches traffi c information standby on/off.
Long press: Switches convenient RDS
function on/off.
40
Contents
Notes and accessories ...................... 43
Disposal of old unit
(EU countries only) ........................43
Installation .................................... 43
Optional equipment(not part of
the scope of delivery) .....................43
Detachable control panel ................. 44
Theft protection.............................44
Detaching the control panel ............. 44
Attaching the control panel ..............45
Switch-off time (OFF TIMER) ........... 45
Switching on/off ..............................46
Adjusting the volume .......................46
Setting the power-on volume ........... 46
Quickly reducing the volume (Mute) .. 47
Telephone Audio/Navigation Audio ... 47
Switching the confi rmation
beep on/off ................................... 48
Automatic Sound ........................... 48
Radio mode .....................................49
Adjusting the tuner.........................49
Switching to radio mode .................49
Convenient RDS functions (AF, REG) .. 49
Selecting the waveband/
memory bank ................................ 50
Tuning into a station ....................... 50
Setting the sensitivity of
station seek tuning ......................... 51
Storing stations ............................. 51
Storing stations automatically
(Travelstore) .................................51
Listening to stored stations ............. 52
Scanning receivable stations (SCAN) ...52
Setting the scanning time ................ 52
Programme type (PTY) .................. 52
Traffi c information ........................... 55
Switching traffi c information
priority on/off ............................... 55
Setting the volume for traffi c
announcements ............................. 55
CD mode .........................................56
Switching to CD mode ....................56
Selecting tracks ............................. 56
Fast track selection ........................ 56
Fast seek tuning (audible) ............... 57
Random track play (MIX) ................. 57
Scanning tracks (SCAN)..................57
Repeating tracks (Repeat) ............... 57
Interrupting playback (PAUSE) .........57
Confi guring the display ...................58
Displaying CD text .......................... 58
Traffi c announcements in CD mode .. 58
Ejecting a CD................................. 59
MP3/WMA mode ............................. 59
Preparing an MP3 CD ..................... 59
Switching to MP3 mode .................. 61
Confi guring the display ...................61
Confi guring the MP3 scrolling texts ... 61
Selecting a directory ...................... 62
Selecting tracks/fi les ...................... 63
Fast seek tuning(not in MP3
browse mode) ............................... 63
Random track play – MIX
(not in MP3 browse mode) .............. 63
Scanning tracks – SCAN
(not in MP3 browse mode) .............. 63
Repeating individual tracks or
whole directories – REPEAT
(not in MP3 browse mode) .............. 64
Interrupting playback (PAUSE) .........64
ENGLISH
Optimising radio reception .............. 54
Confi guring the display ...................54
41
Contents
CD changer mode ............................ 65
Switching to CD changer mode ........65
Selecting CDs ................................ 65
Selecting tracks ............................. 65
Fast seek tuning (audible) ............... 65
Repeating individual tracks or
whole CDs (REPEAT) ......................65
Random track play (MIX) ................. 65
Scanning all tracks on all CDs (SCAN) ...66
Interrupting playback (PAUSE) .........66
Clock time ....................................... 66
Displaying the time ........................ 66
Setting the time ............................. 66
Selecting 12/24-hour clock mode .... 67
Displaying the time continuously
when the device is off and the
ignition is on ................................. 67
Adjusting the display settings ........... 71
Entering a switch-on message .......... 71
Adjusting the display brightness .......72
Adjusting the viewing angle ............. 72
Adjusting a positive or negative
display presentation ....................... 73
Setting the display illumination
colour .......................................... 73
External audio sources ..................... 74
Switching the AUX input on/off ........ 74
Adjusting the AUX preamplifi cation ... 75
TMC for dynamic navigation systems ....75
Technical data ................................. 76
Briefl y displaying time with
switched-off device ........................ 67
Sound ............................................. 68
Adjusting the bass ......................... 68
Adjusting the middle ...................... 68
Adjusting the treble ........................ 68
Setting the left/right volume
distribution (balance) ..................... 69
Adjusting the front/rear volume
distribution (fader) ........................ 69
Preamplifi er output
(Preamp-Out/Sub-Out) ....................69
Adjusting the sub-out level ..............69
Adjusting the sub-out
cut-off frequency ........................... 69
X-BASS ...........................................70
Adjusting the X-BASS boost ............. 70
Equalizer presettings (Presets) ........ 71
42
Notes and accessories
Notes and accessories
Thank you for choosing a Blaupunkt product. We hope you enjoy using this new piece
of equipment.
Please read these operating instructions
before using the equipment for the fi rst
time.
The Blaupunkt editors are constantly working on making the operating instructions
clearer and easier to understand. However,
if you still have any questions on how to operate the device, please contact your dealer
or the telephone hotline for your country.
You will fi nd the telephone number printed
at the back of this booklet.
We provide a manufacturer's warranty for
our products bought within the European
Union. The warranty terms can be called
up under www.blaupunkt.de or requested
directly from:
Road safety
Road safety has absolute priority.
Only operate your car sound system
쏅
if the road and traffi c conditions allow you to do so.
Familiarise yourself with the device
쏅
before setting off on your journey.
You should always be able to hear police, fi re and ambulance sirens in good
time from inside your vehicle.
For this reason, listen to your car
쏅
sound system at a suitable volume
level during your journey.
Installation
If you want to install your car sound system
yourself, please read the installation and
connection instructions that follow these
operating instructions.
ENGLISH
Blaupunkt GmbH
Hotline
Robert Bosch Str. 200
D-31139 Hildesheim, Germany
Disposal of old unit
(EU countries only)
Do not dispose of your old unit in the
household trash!
Please use the return and collection systems available to dispose of the old unit.
Optional equipment
(not part of the scope of delivery)
Use only accessories approved by
Blaupunkt.
Remote control
The steering wheel and/or handheld remote
control allows you to access the basic functions of your car sound system safely and
conveniently.
You cannot switch the device on/off using
the remote control.
You can fi nd out from your Blaupunkt dealer
or on the Internet at www.blaupunkt.com
which remote controls can be used with
your car sound system.
43
Notes and accessories Control panel
Amplifi er
You can use all Blaupunkt and Velocity amplifi ers.
CD changers
You can connect the following Blaupunkt
CD changers:
CDC A 03, CDC A 08 and IDC A 09.
Detachable control panel
Theft protection
The device is equipped with a detachable
control panel (fl ip-release panel) as a way
of protecting your equipment against theft.
The device is worthless to a thief without
this control panel.
Protect your device against theft by taking
the control panel with you whenever you
leave your vehicle. Do not leave the control
panel inside your vehicle - not even in a hiding place.
Notes:
•
Never drop the control panel.
•
Never expose the control panel to direct sunlight or other heat sources.
•
Avoid direct skin contact with the
control panel’s electrical contacts. If
necessary, please clean the contacts
with a lint-free cloth moistened with
cleaning alcohol.
Detaching the control panel
Press the button 2.
쏅
The control panel opens out towards you.
쏅
Hold the control panel by its right side
and then pull the control panel straight
out of the bracket.
44
Control panel
Notes:
The device is switched off after a time
•
preset by you. For further details,
please read the section "Switch-off
time (OFF TIMER)" in this chapter.
All the current settings are saved.
•
Any CD already inserted in the device
•
remains there.
Attaching the control panel
Hold the control panel approximately at
쏅
a right angle to the device.
Slide the control panel into the de-
쏅
vice’s guides that are positioned on the
left and right at the lower edge of the
housing. Push the control panel carefully into the bracket until it clicks into
Switch-off time (OFF TIMER)
After opening the control panel, the device
is switched off after an adjustable time. You
can set this time from 0 to 30 seconds.
Press the MENU button 9.
쏅
Press the
쏅
until "VARIOUS MENU" appears on the
display.
Press the
쏅
menu.
Press the
쏅
until the displays shows "OFF TIMER".
Set the time with the
쏅
:.
When you have fi nished making your changes,
or button : repeatedly
button : to open the
or button : repeatedly
or button
ENGLISH
place.
쏅
Carefully fl ip up the control panel until
it clicks into place.
2.
1.
If the device was still switched on when you
detached the control panel, it will automatically switch on with the last setting activated (radio, CD, CD changer or AUX) when
the panel is replaced.
press the MENU button 9 three
쏅
times.
Note:
If you set the switch-off time to 0 seconds, the device is switched off immediately after opening the control panel.
45
Switching on/off Volume
Switching on/off
There are various ways of switching the device on/off:
Switching on/off using button 1
To switch on the device, press button
쏅
1.
The device switches on.
To switch off the device, press and
쏅
hold down button 1 for longer than
two seconds.
The device switches off.
Switching on/off using the vehicle
ignition
The device will switch on/off simultane-
Adjusting the volume
You can adjust the volume in increments
from 0 (off) to 66 (maximum).
To increase the volume,
turn the volume control 3 clockwise.
쏅
To decrease the volume,
쏅
turn the volume control 3 counterclockwise.
Setting the power-on volume
Note:
The device features a time-out function
(time window).
For example, if you press the MENU
button 9 and select a menu item, the
ously with the ignition if the device is correctly connected to the vehicle’s ignition as
shown in the installation instructions and
you did not switch the device off by pressing button 1.
Switching the device on/off using the
detachable control panel
Detach the control panel.
쏅
The devices switches off after the time set
in the "OFF TIMER" menu.
Attach the control panel again.
쏅
The device switches on. The last setting
(radio, CD, CD changer or AUX) is reactivated.
Note:
To protect the vehicle battery, the device will switch off automatically after
one hour if the ignition is off.
device switches back after approx. 8
seconds after the last button activation.
The settings performed are saved.
You can set the power-on volume.
쏅
Press the MENU button 9.
쏅
Press the
until "VOLUME MENU" appears on the
display.
Press the
쏅
menu.
Press the
쏅
edly until "ON VOLUME" appears on the
display.
Set the power-on volume with the
쏅
button :.
To help you adjust the setting more easily,
the device will increase or decrease the volume as you make your changes.
or button : repeatedly
button : to open the
or button : repeat-
or
46
Volume
If you enable "LAST VOL", the volume which
was set the last time you switched off the
device is re-enabled.
Note:
To protect your hearing, the power-on
volume is limited to the value "38". If
the volume before switching off was
higher and the "LAST VOL" setting was
selected, the device switches on again
with the value "38".
When you have fi nished making your changes,
쏅
press the MENU button 9 three
times.
Quickly reducing the volume
(Mute)
You can quickly reduce the volume to a preset level (Mute).
쏅
Briefl y press button 1.
Press the
쏅
edly until "MUTE LVL" appears on the
display.
Set the mute level with the
쏅
button :.
When you have fi nished making your changes,
press the MENU button 9 three
쏅
times.
or button : repeat-
or
Telephone Audio/Navigation
Audio
If your car sound system is connected to a
mobile telephone or a navigation system,
the sound system’s volume will be muted as
soon as you “pick up” the phone or as soon as
a navigation announcement is made. You will
then hear the caller or navigation announcement over the car sound system’s loudspeakers. In order for this feature to work, the mobile telephone or navigation system must be
ENGLISH
"MUTE" appears on the display.
Cancelling mute
To return to your previously set volume
level,
쏅
briefl y press button 1 again.
Adjusting the mute level
You can adjust the mute level.
쏅
Press the MENU button 9.
쏅
Press the
until "VOLUME MENU" appears on the
display.
쏅
Press the
menu.
or button : repeatedly
button : to open the
connected to the car sound system as described in the installation instructions.
You can fi nd out from your Blaupunkt dealer
which navigation systems can be used with
your car sound system.
If the sound system receives a traffi c announcement during a telephone call or
whilst a navigation announcement is being made, you will only be able to hear the
traffi c announcement after the call or navigation announcement is fi nished (in so far
as the traffi c announcement is still being
broadcast). The traffi c announcement is
not recorded!
You can adjust the volume with which you
switch on the telephone calls or the voice
output of the navigation.
47
Volume
Press the MENU button 9.
쏅
Switch the BEEP ON or OFF with the
쏅
Press the
쏅
until "VOLUME MENU" appears on the
display.
Press the
쏅
menu.
Press the
쏅
until "TEL VOL" appears on the display.
Set the desired volume with the
쏅
button :.
When you have fi nished making your changes,
쏅
press the MENU button 9 three
times.
Note:
You can use the volume control 3 to
adjust the volume of telephone calls
and navigation announcements whilst
you are listening to them.
or button : repeatedly
button : to open the
or button : repeatedly
or
or button :.
When you have fi nished making your changes,
press the MENU button twice 9.
쏅
Automatic Sound
This function automatically adjusts the volume of the car sound system to the vehicle
speed. For this purpose, the car sound system must be connected as described in the
installation instructions.
You can adjust the automatic sound in 6 increments from (0 - 5).
Press the MENU button 9.
쏅
Press the
쏅
until "VOLUME MENU" appears on the
display.
Press the
쏅
menu.
or button : repeatedly
button : to open the
Switching the confi rmation beep
on/off
The system will output a confi rmation beep
for some functions if you keep a button
pressed down for longer than two seconds,
for instance, when assigning a radio station
to a station preset button. You can switch
the beep on or off.
쏅
Press the MENU button 9.
쏅
Press the
until "VOLUME MENU" appears on the
display.
Press the
쏅
menu.
Press the
쏅
until "BEEP ON" or "BEEP OFF" appears
or button : repeatedly
button : to open the
or button : repeatedly
Press the
쏅
edly until "AUTO SD" appears on the
display.
Set the automatic sound 0 - 5 with the
쏅
or button :.
When you have fi nished making your changes,
press the MENU button 9 three
쏅
times.
Note:
Your optimal setting of 0 - 5 of the
speed-dependent sound adjustment
depends upon the driving noise development of your vehicle. You will need to
test various settings in order to fi nd out
which is best suited to your vehicle.
or button : repeat-
on the display.
48
Radio mode
Radio mode
This device is equipped with an RDS radio
receiver. Many of the receivable FM stations
broadcast a signal that not only carries the
programme but also additional information
such as the station name and programme
type (PTY).
The station name appears on the display as
soon as the tuner receives it.
Adjusting the tuner
To ensure proper functioning of the tuner,
the device must be set for the region in
which it is being operated. You can select
among Europe "EUROPE", America "USA",
South America "S-AMERICA", and Thailand
"THAI". The tuner is factory-set to the region in which it was sold. If you experience
problems with your radio reception, please
check this setting.
To save the setting,
switch the device off and on again or
쏅
wait approx. 8 seconds. The radio
starts playing with the last setting selected (radio, CD, CD changer or AUX).
Switching to radio mode
If you are in CD, CD changer or AUX mode,
press the BND•TS button 6
쏅
or
press the SOURCE button 4 repeat-
쏅
edly until the memory bank, e.g. "FM1",
appears on the display.
Convenient RDS functions
(AF, REG)
The convenient RDS functions AF
(Alternative Frequency) and REGIONAL extend your radio’s range of functions.
ENGLISH
The radio functions described in these operating instructions refer to the tuner setting EUROPE.
쏅
Switch off the device by pressing button 1.
쏅
Hold the buttons 1 and 5 ; pressed at
the same time and switch on the device
again with the button 1.
"TUNER" is displayed.
쏅
Select your tuner region with the
button :.
or
AF: If the RDS function is activated, the
•
radio automatically tunes into the best
receivable frequency for the station
that is currently set.
REGIONAL: At certain times, some ra-
•
dio stations divide their programme
into regional programmes providing
different content. You can use the REG
function to prevent the car radio from
switching to alternative frequencies
that are transmitting different programme content.
Note:
REGIONAL must be activated/deactivated separately in the menu.
49
Radio mode
Switching REGIONAL on/off
Press the MENU button 9.
쏅
"USER MENU" appears on the display.
Press the
쏅
edly until "TUNER MENU" appears on
the display.
Press the
쏅
menu.
Press the
쏅
until "REG" appears on the display.
"OFF" or "ON" is displayed alongside
"REG".
To switch REGIONAL on/off,
쏅
press the
When you have fi nished making your changes,
or button : repeat-
button : to open the
or button : repeatedly
or button :.
Six stations can be stored in each memory
bank.
To switch between the FM memory banks
(FM1, FM2 and FMT) and the MW and LW
wavebands,
쏅
briefl y press the BND•TS button 6.
Tuning into a station
There are various ways of tuning into a station.
Automatic station seek tuning
쏅
Press the
The radio tunes into the next receivable station.
Tuning into stations manually
or button :.
press the MENU button twice 9.
쏅
Switching the RDS function on/off
To switch the RDS functions AF and
REGIONAL on or off,
쏅
press and hold down the TRA•RDS but-
ton 7 for longer than two seconds.
"RDS ON" or "RDS OFF" is activated and
briefl y appears on the display.
Selecting the waveband/memory
bank
This device can receive programmes broadcast over the FM frequency range as well as
the MW and LW (AM) wavebands. There are
three memory banks available for the FM
You can also tune into stations manually.
Note:
You can only tune into stations manually if the convenient RDS function is
deactivated.
To change the set frequency in small increments,
쏅
briefl y press the
To change the set frequency quickly,
쏅
press and hold down the
: for a longer period of time.
or button :.
or button
waveband (FM1, FM2 and FMT) and one
for each of the MW and LW wavebands.
50
Loading...