The equipment has been tested and found to comply with the limits for a Class B device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and, if not installed and used in accordance with instructions, may cause
harmful interference with radio communications. However, there is no guarantee that radio
interference will not occur in particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to contact the dealer or an experienced
help.
You are cautioned that any changes or modifications not expressly approved in this manual could
void your authority to operate this equipment.
RadioE!V
technician for
Owner’s Record
The model and warranty numbers are located on the top of the unit. Record the warranty (serial)
number in the space provided below. Refer to these numbers whenever you call upon your
Blaupunkt dealer regarding this product.
Warranty Number
Attach Sales Receipt Here
Table of Contents
.
English
FCC Warning
Owner’s Record..
Features ...........................................................
Precautions
Detachable Face
Electrical Connections and Installation
Installation
Maintenance
Specifications
Emplacements des
Mode d’Emploi/Fonctionnement General..
Fonctionnement de
Fonctionnement delaRadio..
Fonctionnement du Lecteur de Cassette..
Prise Auxiliare
Guide de Depannage
Congratulations on your purchase of this Blaupunkt Cassette Receiver. Its
Codem
III-US FM/AM
Tuner and Autoreverse Cassette Tape Player mechanism provide the ultimate in sound
reproduction. Its high-power amplifier and
4Channel
preamp output provide you with tremendous
system configuration flexibility. Its auxiliary input jack lets you easily incorporate portable audio
equipment, such as a CD or DAT player, into your car’s sound system.
l
l
Codem
-
-
-
-
III-US Tuner Features:
Multipath Management
ASU Electrical Impulse Noise Reduction
Superior AM Frequency Response
15 FM/5 AM Presets, Including 5 FM
5 AM Travelstore Presets
-
Station Scan
-Local/Distant Seek & Manual Tuning
&
Audio Features:
-35 Watts x 4 Channel Integrated Amplifier
-
Dual-Level Fader
-3.0 Volt Max. Preamp Output (Max. w/
cl%
4-Channel, Low lmpendance (100 Q) Preamplifier
- 2Channel
-
BassTreble, Balance, Fader Controls
RCA Preamp Output Harness Included
-Adjustable Maximum Turn-On Volume
-Loudness Button
l Cassette Tape Player Features
-Auto-Reverse Cassette Mechanism
-
True Fast-Forward/Rewind
-
Hard Permalloy Tape Head
-Radio Monitor with Radio Preset Access
-Dolby B Noise Reduction
Your unit’s detachable front faceplate makes the
unit useless to would-be thieves.
-Mute Button
-Auxiliary Input
l
Other Features:
-
Detachable Face
-Display Priority Control
-
Temoorarv Display Change Control
- Clock/lgniiion-bff
-18Ox50x155mm
DIN/IS0
Chassis
Clock Recall
(7x2x6l/Bin.)
-Detachable Wire Harness
Designed, Engineered and Manufactured
f3y
Blaupunkt.
-Snap-In DIN Sleeve & Mounting Hardware
-Side-Mount Compatible
THD)
Traffic Safety and Precautions
l Do not adjust your unit in difficult driving conditions that demand your full attention.
l As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation at all
times. Never use your unit in a way that could distract you.
l Always make sure that you are still able to hear any warning signals coming from outside of the
vehicle, such as police or fire engine sirens, so that you can react accordingly.
l If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside
the vehicle, allow the unit to cool off before operating your unit.
l You are cautioned that any changes or modifications not expressly approved in this manual could
void your warranty.
l Car Wash precaution
the tuner
- so
that the antenna is lowered and antenna damage is prevented.
-
If you have a motorized antenna, make sure to turn off the unit - not just
.
Detachable
Detaching & Attaching the Face:
The face of this unit can be detached and taken with you to prevent it from being stolen.
Detaching the Face:
Press the
Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it
from the chassis.
Attaching the Face:
Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at the
front of the chassis. Gently push the left side of the face against the front of the chassis until it
snaps into place.
Note: Make sure that the face is inserted right side up. Do not press against the display window.
Do not press hard against the face when attaching it to the chassis, it may be easily attached with
gentle pressure. Do not expose the face to direct sunlight, heat sources such as hot air ducts or
leave it in a humid place. Never leave it on the dash board of a vehicle parked in direct sunlight,
where there may be a considerable rise in temperature inside the vehicle.
Affixing Faceplate For Retail Display:
The faceplate can oe affixed to the unit’s chassis, which is desirable for a retail display, for
example.
REL
(Release) Button and detach the face by gently pulling it off as illustrated.
Face
*
To affix the faceplate:
Insert the black bolt into the hole at the left front of the top of the radio. See* below.
5
Electrical Connections and Installation
@/c?#&*>@! To avoid the aggravation of costly mistakes and serious damage that could make
you feel this way, please carefully read all of the instructions before you begin. Carefully follow all
instructions. You’ll be glad you did!
GENERAL RECOMMENDATIONS
l If you’re not confident that you can install the unit correctly, have it installed by a qualified
Blaupunkt installation technician.
l Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC).
l Be sure to detach the faceplate before you start to connect or install the unit.
l We recommend making and testing all electrical connections before installing the unit. Connect
the leads (wires) according to instructions and diagram below.
ELECTRICAL CONNECTION INSTRUCTIONS
Disconnect the vehicle battery’s negative terminal before making connections.
1.
Connect the speakers and/or external amplifiers (if you have any) following the guidelines in
2.
the SPEAKER CONNECTION section below.
Connect the blue (trigger output) lead to an amplifier’s trigger input terminal and/or antenna
3.
motor trigger input terminal (if you have either or both of these items). The combined total
amperage required for triggering the antenna motor and/or amplifier must not exceed 300
DO NOT connect the blue lead to the antenna’s and/or amplifier’s power supply input.
Connect the black (power ground) lead to a grounded metal part on the vehide. We
4.
recommend grounding all audio system black ground leads (head unit,
external
amplifier, etc.)
to a common grounding point, preferably a non-painted surface under the instrument panel.
Connect the yellow (constant power) input lead to a source of constant battery power,
5.
preferably a terminal to an appropriate slot in the fuse box.
6.
Connect the red (turn-on power) input lead only after the other leads are connected. Be sure to
connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the
ignition key is set to the on position or accessory position.
7.
Cover the ends of any unused leads with electrical tape. This will prevent them from touching
the vehicle or each other and causing a short-circuit and damage to the radio or vehicle.
8.
Reconnect the vehicle’s battery.
9.
Verify that no fuses have blown.
10. Plug the harness into the unit.
11. Attach the faceplate and test the unit.
Once the connections have been successfully made, you can begin to mount the unit.
mA.
SPEAKER
The unit’s Dual-Level Fader allows you to fade between the front and
CONNECT;ONS
the
rear channels using either
the front and/or rear speaker leads and/or the rear preamp outputs, providing you tremendous
flexibility in configuring your speaker arrangement:
You can connect a speaker (regular, co-axial or tri-axial speakers or component speaker system,
all hereafter referred to simply as “speaker”) to each of the units’ four pairs of speaker leads.
You can connect the 2 RCA preamp outputs to multiple external amplifiers and power multiple
speakers or speaker systems through the amplifiers. (Blaupunkt amplifiers and speakers
available
separately). To add front preamp output, purchase Blaupunkt part 8634494218.
You can use a combination of these two methods.
Connecting the Speaker Leads
To prevent short circuits or serious damage to the unit
l Connect the speaker leads only as indicated in the wiring diagram. Disconnect the vehicle
and/oi
speakers:
battery’s negative terminal before making connections.
l Only use speakers that have impedance ratings of 4 ohms or higher and have power-handling
capabilities greater than the head unit’s stated power level.
l The unit’s internal amplifier is designed to handle a
l DON’T connect two speakers to a single pair of speaker leads (“in parallel”) unless both speakers
4-ohm
load on each pair of speaker leads.
each have at least 8 ohms impedance.
6
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.