Black Widow BW RAS 651 User Manual

Button 1 Button 2

Button 3 Button 4

REMOTE AUTO START

Optional Keyless Entry Instructions Included

SYSTEM MANUAL

STANDARD FEATURES

Some of the system’s standard features include:

• 4-button remote transmitter

•Extended range receiver w/built-in LED status
indicator & valet switch

• Flashing parking lights

• Auto cold Start feature

• Stop & go feature

• Programmable engine run-time

• Hood & brake pedal safety inputs

SYSTEM OPERATION

DOOR LOCKING

To lock the system press transmitter button 1:

• The parking lights will flash once.

• The horn will honk once.*

• The doors will lock.*

• The LED will begin flashing after 3
seconds.

• The Starter Defeat feature will activate.*

Optional Feature

*

OPTIONAL FEATURES

This system has optional features that may
require additional parts and/or labor. Please
contact your dealer for more details.

• Remote keyless entry (door lock/unlock)

• Trunk/hatch release
Note: Some features may not be appropriate

for certain vehicles.

REMOTE TRANSMITTER BUTT ONS

Transmitter Icons

NOTE: Transmitter cosmetics may differ, but
button functions remain the same as described:

Button 1 locks the doors* and also activates
the Panic Mode* when held for 4 seconds.

Button 2 unlocks the doors*.
Button 3 controls the Remote Start feature.
Button 4 activates the Car Finder feature.

1

COMFORT CLOSURE

The optional Comfort Closure feature activates
the lock output as long as button 1 is held. Using
this feature will roll-up the windows and close
the sunroof on some late model vehicles.

To activate the Comfort Closure feature:

1. Press and release transmitter button 1 to
lock the doors.

2. Immediately press and hold button 1 again
until the windows and sunroof are closed.

• The LED will flash once.

• The parking lights will flash once.

• The doors will lock.*

Optional Feature

*

DOOR UNLOCKING

To unlock the system press transmitter button 2.

• The parking lights will flash twice.

• The horn will honk twice.*

• The doors will unlock.*

• The LED will stop flashing.

• The Starter Defeat will deactivate.*

Optional Feature.

*

SILENT LOCKING/UNLOCKING

If the optional Horn Honk feature is installed,
pressing transmitter buttons 1&2 together
provides one-time silent operation. The system
locks or unlocks the doors without horn
confirmation.

IGNITION CONTROLLED LOCKS

The ignition controlled locks feature
automatically locks the doors after turning on
the ignition, and unlocks when the ignition key
is turned off. This feature may also be
programmed for ignition lock without ignition
unlock,and off (no ignition control).

VALET MODE

When the system is placed into the Valet Mode
the remote start feature will be disabled.
However,the optional keyless entry and trunk
release features will still function if installed.

To enter mode:

1. Be sure the system is in unlock mode.

2. Turn ignition on.

3. Press and hold the valet switch for 5
seconds.

• The LED will turn on solid 5 seconds

after turning ignition off.

• The horn will honk 5 times.*

4. Turn ignition off.

To exit valet mode:

1. Be sure the system is in unlock mode.

2. Turn ignition on.

3. Press and hold the valet switch for 5
seconds.

• The LED will turn off.

• The horn will honk twice.*

4. Turn ignition off.

OPTIONAL TRUNK RELEASE

The activate the system’s auxiliary feature (or
trunk release) press button 2 for three

seconds. NOTE:the Trunk Release feature may
be programmed to activate with button 4
instead. See your dealer for more details.

CAR LOCA TOR FEATURE

To activate the system’s car locator feature
press and hold button 4 for three seconds. The
parking lights will flash and the horn will honk
(optional) 5 times.

REMOTE START FEATURES

Important: Only start the vehicle in a well
ventilated area. Do not use in a closed garage
or indoors. Be sure to familiarize yourself with
all features prior to using the remote start.

REMOTE ST AR TING THE VEHICLE

To remote start the vehicle press button 3.

• The parking lights will flash 4 times then
remain on.

• The system will attempt to start.

• Once the car has started,the heater or air
conditioner will turn on and run for the
pre-programmed time.If the engine fails to
start on the first attempt,it will attempt to
start 2 more times. If the vehicle fails to
start after a total of 3 times the system
will shut down.

To drive the vehicle after Remote Starting:

Unlock the door by pressing button 2 on the
remote transmitter. Enter vehicle, turn
ignition key on position and press brak e pedal

NOTE:Do not turn the key to the start position
as the engine is already running.

If brake pedal is pressed prior to turning on
ignition,engine will turn off.

REMOTE ENGINE SHUTDOWN

If the vehicle has been remotely started and
you desire to turn the vehicle off,simply press
and hold button 3 for 3 seconds.

2

STOP AND GO

The Stop and Go feature allows the vehicle to
remain running without use of the ignition key
during short stops.

To activate the Stop and Go feature:

1. Make sure the engine is running.

2. Press button 3.

3. Turn ignition off.

• The doors will unlock.

• The parking lights will turn on.

• The engine will remain running.

4. Exit the vehicle and lock the doors using
transmitter button 1.

To resume driver control:

1. Unlock the doors by pressing transmitter
button 2.

2. Turn on the ignition.

• The vehicle resumes driver control,

when the brake pedal is pressed.

AUTO COLD START

This feature allows the system to start and run
the vehicle every 2, 3, or 4 hours (user
selectable) for up to 12 starts. This allows the
engine to remain at an operational temperature
in extremely cold weather. Auto Cold Start
interval timing must be chosen during
installation.

Engaging the Auto Cold Start feature:

To turn Auto Cold Start on:

1. Press and hold buttons 1 & 3 together for
3 seconds.

• The parking lights will turn on for 10

seconds to confirm activation.

2. Press the button corresponding to the
desired start cycle interval:

Button 2 = start every 2 hours
Button 3 = start every 3 hours
Button 4 = start every 4 hours

• The parking lights will flash a number
of times equal to the chosen interval.

Disengaging the Auto Cold Start feature:
Any of the following actions will cancel the

Auto Cold Start feature:

Press and hold buttons 1 & 3 together for 3
seconds.

• The parking lights will flash twice and
the horn will honk twice (optional) to
confirm deactivation.

- or -

Press the brake pedal.

- or -

Turn ignition on.

SAFETY FEATURES

The System will not start the vehicle if the
brake pedal is pressed,if the hood is open,or if
the system is in Valet mode.Also,if the brake is
pressed or the hood is opened while remote
running,the remote start will shut down.

LED AND PARKING LIGHT DIAGNOSTIC INDICATIONS

Parking Light LED Indication Problem

3 Slow Flashes On Solid System in Valet Mode
5 Slow Flashes No Flashes Key is on during remote start attempt
5 Flashes 5 Flashes Open hood warning (before start)
5 Flashes 5 Flashes System shut down using brake pedal (when running)
7 Flashes 7 Flashes Tachometer lock out (see dealer)

3

REMOTE AUTO START

Optional Keyless Entry Instructions Included

INSTALLATION INSTRUCTIONS

BEFORE INSTALLING THIS PRODUCT PLEASE READ

THE INSTALLATION DIRECTIONS THOROUGHLY!!

BEFORE Y OU BEGIN

This system is compatible with electronic
fuel injected engines only! Not intended for
use with carbureted engines.

• This product must be installed by qualified
personnel according to these instructions and
and observing all safety features.

• Check to see if the vehicle is equipped with
any type of factory security system.

• Check to see if there is a pin switch for the
hood,if not one must be installed.

• Verify that the vehicle starts and idles
properly before beginning the installation.

• Always use a multi-meter to verify wiring.

• Before mounting the product,verify with the
customer the desired location for the window
mount receiver.

MOUNTING SYSTEM COMPONENTS

Mount the start module under the dash where
it will be away from moving parts such as brake
pedals,etc. Mount the receiver to the inside of
the windshield using the supplied double-sided
tape. Make sure the chosen location does not
obscure the driver’s view.

MODULE WIRING
12-Pin Main Harness

• YELLOW WIRE - Factory Alarm Arm output
(-) 250mA.Connect to the wire that requires a
ground pulse to arm the factory alarm. The
YELLOW wire provides a ground pulse when

the remote transmitter is used to lock the
doors or when the remote start shuts down.
See Programmable Features

• RED/WHITE WIRE - Auxiliary / trunk release
output (-) 250mA. Connect to a relay for an
optional feature such as trunk release. The
RED/WHITE wire can instead be programmed
for use as a negative parking light output if
needed, and the WHITE positive parking light
output then becomes a positive trunk release
output.See Programmable Features

• BROWN WIRE - Factory Alarm Disarm
output (-) 250mA. Connect to the wire that
requires a ground pulse to disarm the factory
alarm. The BROWN wire provides a ground
pulse when the remote transmitter is used to
unlock the doors or start the vehicle.

• ORANGE WIRE - Ground when running /
Anti-grind output (-) 250mA. The ORANGE
wire can be also programmed for use as a
Starter Defeat output with Anti-grind or as a
passive Starter Defeat output that activates 30
seconds after the ignition is turned off.

Ground when running (default): Provides a
ground when the remote start is activated and
is normally used to activate an optional factory
security bypass module, a relay for anti-grind,a
3rd ignition relay,etc.

Starter defeat w/ anti-grind: Provides a ground
when the remote start is activated and when
button 1 is used to lock the doors.

Starter defeat w/ passive operation: Provides a
ground to activate a starter defeat relay 30

4