Standard Features
The system has the following standard features:
• (1) 3-button LCD display remote control
• Status indicator (LED)
• Program/Valet switch
• Remote Start capabilities
• Extended Range Transceiver
• Multi-tone siren (120dB)
• Dual stage shock sensor
• Remote panic
• Valet mode
• Remote chirp mute
• Remote sensor bypass
• Passive or active arming
• Stop & Go Feature
• Auto Cold Start
• Flashing parking lights
• Auto Rearm
• Passive Arming
Optional Features
The system has many optional features that may
require additional parts and/or labor. Please
contact your dealer for more details.
• Remote keyless entry (Door lock/unlock)
• Illuminated entry
• Hood & trunk protection
• Horn honk
• Trunk/hatch release
• Window roll-up
• Back up battery
• Additional sensors
glass breakage
microwave
Note: Some features may not be appropriate
for certain vehicles. Automatic transmission
and electronic fuel injection are required on
vehicles for use with this system.
1
FM SECURITY/REMOTE START SYSTEM
OWNERS MANUAL
Security System Operation
ARMING OPERATION
To arm the system press
transmitter button 1:
• The siren will chirp
once.
• The parking lights will
flash once.
• The doors will lock*.
• The L.E.D. will turn solid for 2 seconds
then start flashing slowly. After 10
seconds the system is armed.
*
If Installed
PASSIVE ARMING
The passive arming feature allows the system
to arm automatically without any user
intervention.
This feature must be programmed
during installation.
To arm the system passively:
1. Turn the ignition key off.
• The LED will start flashing rapidly to
indicate that the system is preparing
to arm. The system can be armed at
any time by pressing transmitter
button 1.
2. Close all doors.
• The siren will chirp 30 seconds after
the last door is closed to indicate the
system is now armed*.
• The doors will lock**.
*
As an option, the passive arming chirps can be
eliminated during programming.
** If Passive Locking is programmed during installation.
DISARMING OPERATION
To disarm the system press transmitter
button 1.
• The siren will chirp twice.*
• The parking lights will
flash twice.
• The doors will unlock.
• The optional illumi-
nated entry feature
will turn on the dome
light for 30 seconds.
*
In the event the alarm was triggered while away, the
system will respond with 3 chirps and 3 parking light
flashes.
AUTO REARM FEATURE
The Auto Rearm feature allows the system
to automatically re-arm itself in the event the
system is disarmed and a door is not opened
within 30 seconds.
This feature must be
programmed during installation.
NOTE: This feature will not work on vehicles
with the illuminated entry feature enabled.
CHIRP DELETE
For full time silent operation, the ARM/
DISARM chirps can be permanently disabled.
This feature must be programmed during
installation.
IGNITION LOCK
The ignition locking feature allows the doors
to automatically lock when the ignition key is
turned on, and automatically unlock when
the ignition key is turned off.
This feature must
be programmed during installation.
VALET MODE
When the system is placed into the Valet
Mode, both the remote starting feature and
the security system will be disabled.
However, the keyless entry and trunk release
features will still function.
2
Press
Press
To enter the Valet Mode:
1. Be sure the system is disarmed.
2. Turn the ignition key on.
3. Press and hold the valet/service
mode switch for 3 seconds.
• The LED will turn on solid indicating
the system is in Valet Mode.
To exit Valet Mode:
1. Turn the ignition key on.
2. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn off.
• The Siren will chirp 2 times.
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by
using the emergency override feature.
To override the system:
1. Enter the vehicle.
• Because the system is armed, the
siren will sound.
2. Turn on the ignition key.
3. Press the Valet/Service Mode switch.
• The siren will stop sounding.
REMOTE PANIC
In the event of an emergency (PANIC)
situation, the system’s siren can be triggered
to attract attention. To activate the Panic
Feature, press transmitter button 1 for 3
seconds:
• The siren will sound .
• The parking lights will flash.
The Panic mode will run for 45 seconds, or
until transmitter button 1 is pressed again.
The Panic Feature will not operate when the
ignition is on. Also, if the vehicle is Remote
Started, activating the Panic Feature will shut
down the Remote Start.
TRUNK RELEASE
Press button 3 for approximately 2 seconds to open
the trunk.
TRUNK DISARM FEATURE
The trunk disarm feature allows the alarm to
disarm automatically whenever transmitter
button 3 is used to activate the trunk
release.This eliminates having to first disarm
the alarm before activating the trunk release.
This feature must be programmed during
installation.
CAR LOCATOR FEATURE
The Car Locator feature allows the parking
lights to stay on for 30 seconds instead of
flashing when the alarm is disarmed.
This
feature must be programmed during installation
and is not recommended for vehicles with
additional aftermarket or auxiliary lighting.
3
Press
Remote Start Operation
Important: The system should be placed
into the valet mode when parked inside a
garage or being left for service. Only
start the vehicle in a well ventilated area.
Do not use in a closed garage or indoors.
Be sure to familiarize yourself with all
features prior to using this product.
REMOTE STARTING THE VEHICLE
To remote start the vehicle:
Press button 2 on the transmitter.
• The siren chirps 3 times.
• The parking lights turn
on.
• Approximately 2
seconds later the
system will attempt
to start the vehicle.
• Once the car has started, the heater or
air conditioner will turn on and run for
the preprogrammed time (15 or 25
minutes). If the engine fails to start on
the first attempt, it will repeat the
starting procedure 2 more times. If the
vehicle fails to start after a total of 3
times the siren will chirp 4 times.
Driving vehicle after Remote Starting:
Unlock the door by pressing button 1 on
the remote transmitter. Enter vehicle, turn
ignition key to the on position (
Note:Do not
turn the key all the way to the start position as
you may damage the starter
).
Once the ignition key is turned to the on
position, press the brake pedal and shift the
car into the proper gear and you may now
drive the vehicle (
Note: If brake pedal is
pressed prior to turning on ignition, engine will
turn off
).
REMOTE ENGINE SHUTDOWN
If the vehicle has been remotely started and
you desire to turn the vehicle off, simply
press button 2 on the remote transmitter.
After the motor has turned off the doors
will relock (optional).
AUTO COLD START
Cold start feature allows the remote starter
to start and run the vehicle every one or
two hours (selectable by your installer) for a
period of 24 hours.This allows the engine to
remain at an operational temperature in
extremely cold weather.
Auto Cold Start must
be enabled during installation or it cannot be
engaged
.
Engaging the Auto Cold Start feature:
To turn Auto Cold Start on:
While holding the brake pedal down, push
the program switch and transmitter button
2 for two seconds.
• The parking lights will flash three times.
• The siren will chirp three times.
• The engine will start and run for thirty
seconds to indicate the Cold Start
feature is engaged.
Disengaging the Auto Cold Start feature:
The Auto Cold Start feature can be
deactivated in one of three ways:
• Press the brake pedal.
• Turn on the ignition.
• Remote start the vehicle using the
transmitter.
4
Press
5
STOP AND GO
The Stop and Go feature allows the vehicle
to remain running without use of the
ignition key during short stops.
To activate the Stop and Go feature:
1. Press and hold the brake pedal.
2. While pressing the brake pedal, push
transmitter button 1.
• The LED will flash rapidly.
• The parking lights will flash four
times.
3. Release the brake pedal.
4. Remove the key from the ignition
switch.
5. Exit the vehicle and lock the doors
manually or using transmitter button
1*.
To resume driver control:
1. Unlock the doors manually or by pressing transmitter button 1.*
2. Turn on the ignition.
3. Press the brake pedal.
• The vehicle resumes driver control.
• The LED will turn off.
*
If optional keyless entry feature is installed.
SAFETY FEATURES
The system will not start the vehicle if the
brake pedal is pressed or the hood is open.
Also, if the brake is pressed or the hood is
opened while remote running, the remote
start will shut down.
REPLACING LOST OR STOLEN
REMOTE TRANSMITTERS
The system can “learn” a maximum of 2
LCD transmitters. To add a transmitter or
replace lost/stolen transmitters, please
consult with an authorized dealer.
STATUS INDICATOR (LED) FUNCTIONS
On Solid = Valet Mode
Slow Flash = System Armed
Rapid Flash = Passive Arming
Flash 2x = Remote Start
Flash 3x = Stop and Go Mode
Flash 4x = Cold Start Mode
PARKING LIGHTS FUNCTIONS
On Solid = Vehicle Remote Starting
Flash 1x = Doors Locked
Flash 2x = Doors Unlocked
Flash 3x = Open Zone Indication (after arming)
Flash 4x = Remote Starting Failed
Flash 5x = Auto Cold Start Engaged
SYSTEM REFERENCE INDICATORS
6
© David Levy Company, Inc., FM200/Rev.1, 01/01
DLC/U.S.A. 12753 Moore Street • Cerritos, California 90703
DI
Door -
If a door is opened while the
system is armed, the icon
will be displayed, the doorframe
will animate, and the icon
will be displayed.
Start -
The display will show the
icon and the icon to indicate
the ignition is turned on and
the engine is going to crank.
When the engine starts and
continues to run, the icon
will be displayed, the exhaust
icon will flash and the icon
will rotate.
Shock/Page -
The display will show the
icon and flash the animated
icon to indicate shock sensor
triggering (when the system is
armed) or a passenger paging
from the vehicle (when the
system is disarmed).
Warn Away -
If the warning stage of the
shock sensor is triggered, the
icon and the icon will
alternately flash.
Trunk -
The display will flash the
icon opening to confirm
trunk operation.
Disarm -
The display will flash the
icon and the animated
to confirm disarming. If the
alarm was triggered while away
the icon will be displayed.
Arm
Start
Trunk
TRANSMITTER OPERATION
ARM
DIS
ARM
LOCK
UNLOCK
Button
I
II
III
II III
+
Operation
ARM/DISARM/PANIC Button -
To arm or disarm t
system, press button 1. To activate the panic feature,
press
START Button -
To start the vehicle, press and hold
button 2 for two seconds. To shut down the vehicle,
press button 2 and hold for two seconds.
TRUNK Button -
To activate the trunk output, press button 3.
STATUS CHECK -
To check current status of the system
press buttons 2 and 3 together. The current status of the
system
Transmitter Confirmation Indications
Arm -
The display will flash the
icon and the animated
icon to confirm arming.
Note:
Some icons that appear on the transmitter are reserved for
future use and have no functions at this time.
SVC
ARM
UNLOCK
O.K.
LOCK
ARM
LOCK
DIS
ARM
UNLOCK
Loading...