Black Widow BW 852 Installation Manual

REMOTE KEYLESS ENTRY

BEFORE INSTALLING THIS PRODUCT PLEASE READ

THIS INSTALLATION MANUAL THOROUGHLY!!

INSTALLATION MANUAL

• This product must be installed by qualified per­sonnel according to these instructions.

Items Included:

• Main unit

• Two 4-button remote transmitters

• Plug In LED

• Plug in program switch

• Main harness

• Owner’s manual

Before you begin the installation:

• Verify with the customer the desired location
for the program switch and LED.

• Always use a multimeter when verifying vehicle
wiring.

Installation Notes:

• Do not install the main unit in the engine com-

partment.

• Make all wiring connections to the vehicle

before connecting the main 15-pin connector har­ness to the main unit.

• Mount the main unit in a secure area,away from

vehicle computers and heating/air conditioning
ducts.The location should be convenient for your
installation, but hidden from thieves. Mount the
unit as far away from metal objects as possible to

increase the range of the remote transmitters.

• When running the harness wires through the

vehicle, be careful to run them where they cannot
be damaged or shorted. Keep them away from any
moving parts or areas of high heat. Use rubber or
plastic grommets to protect the harness wires
where they pass through holes in metal panels.

Main Harness:

• BLACK WIRE - Ground input (-). Connect to a
solid chassis ground that is clean and free of
paint or dirt.

• RED WIRE - +12V battery input.

• WHITE WIRE - Parking light output (+).
Connect to the wire that shows +12V when the
parking lights are turned on. If the vehicle’s park­ing light circuit exceeds 10A, a relay is required.
For vehicle’s with independent left and right parking
light circuits,the parking light wires must be connect­ed using diodes to keep the circuits separate.

• VIOLET WIRE - Unlock #87 normally open
input 10A fuse. (see Door Lock Wiring Diagrams)

• BLUE/BLACK WIRE - Unlock #30 common
output. (see Door Lock Wiring Diagrams)

• BROWN/BLACK WIRE - Unlock #87A normal­ly closed input. (see Door Lock Wiring Diagrams)

• VIOLET/BLACK WIRE - Lock #87 normally
open input 10A fuse. (see Door Lock Wiring

Diagrams)

• GREEN/BLACK WIRE - Lock #30 common out­put. (see Door Lock Wiring Diagrams)

• WHITE/BLACK WIRE - Lock #87A normally
closed input. (see Door Lock Wiring Diagrams)

• ORANGE WIRE - Armed Output (-) 500Ma.
The ORANGE wire provides ground when the
unit is armed to activate a starter disable relay.
Connect to a relay for starter defeat.. (See Relay

Wiring Diagrams)

• BLACK/YELLOW - Dome light output (-)
500mA. Connect to a relay to activate the dome
light when the system is unlocked. (See Relay

Wiring Diagrams)

• GRAY WIRE - 3rd channel output (-) 500mA.
Connect to a relay for optional trunk release etc.

(See Relay Wiring Diagrams)

• BROWN WIRE - Horn honk output (-) 500mA.
Connect to a relay to honk the vehicle’s horn.(See

Relay Wiring Diagrams)

• BLUE/WHITE WIRE - Passenger unlock output
(-) 500mA. The BLUE/WHITE wire provides a
ground to unlock the passenger doors when the
unlock button on the transmitter is pressed two
times. To install the two-step unlock feature, the
BLUE/BLACK and BROWN/BLACK wires must
be run directly to the driver’s door actuator
unlock wire and the BLUE/WHITE wire must be
connected to a relay to unlock the passenger
doors. (see Optional Two-Step Unlock Diagrams)

• YELLOW WIRE - Ignition input (+). Connect to
the main ignition wire that switches +12V and
does not drop out during cranking.

2-Pin Red Connector: Plug-in connector port for
LED. Mount LED in an area where it may be easily
seen from either side of the vehicle.

2-Pin Blue Connector: Plug-in connector port for
program/service switch. Mount program switch in
an area that is easily accessible from the driver’s
position.

Adding or Deleting Remote Controls

When you enter the code learning mode, the sys­tem will learn new remotes and automatically
delete all other remotes that were previously
operating the system.

NOTE:You must code all desired remotes at this
time.The unit can learn a maximum of three trans­mitters.

To enter Code Learning Mode:

1. Turn ignition key on, off, on, off, on and leave
on within 5 seconds.The horn will chirp once
(if installed) and the LED and parking lights
will flash once.

2. Press and hold program switch for 2 seconds.
The horn will chirp three times and the LED
and parking lights will flash three times.

3. Release the program switch.

4. Program all desired remotes by pressing
button one (or LOCK button) of each of the
transmitters. The parking lights will flash
after the system has learned each remote
control.

5. Turn ignition key off. Remotes are now pro­grammed to the system.

2

Remote Programmable Features:

Step Function Button 1 (Default) Button 2

1. Ignition Controlled Door Locks On Off

2. Door Unlock Pulse Single Double

3. Arming Mode Standard Silent

4. Door Lock Pulse Length .75 Seconds 3 Seconds

5. Passive Starter Defeat Enable Off On

6. Ignition Trigger Feature Off On

Remote Programmable Features

To enter program mode:

1. Turn ignition to the on position.

2. Wait 2 seconds.

3. Within 10 seconds press program switch 5
times.

4. The LED and parking lights will flicker to indi­cate the system is now in program mode.

To change programmable features:

Press program switch the number of times equal
to the feature you wish to change. The LED will
flash each time the switch is pushed. (Example:
to program feature #3 press the program switch
3 times).

• Press button 2 (Unlock) on the remote
to change the feature. The LED will flash
twice.

• Press button 1 (Lock) on the remote to
reset the feature back to default (factory) set­ting.The LED will flash once.

System will automatically exit program mode.

Programmable Features

Program #1:

Ignition Controlled Door Locks

.
Button 1 = Doors lock with ignition
Button 2 = Doors do not lock with ignition

Program #2:

Door Unlock Pulse

Button 1 = Single
Button 2 = Double

Program #3:

Optional Horn Mode

Button 1 = Chirp with Lock/Unlock

Button 2 = Silent

Program #4:

Door Lock Pulse Length

Button 1 = 0.5 second door lock/unlock pulse
Button 2 = 3 second door lock/unlock pulse

Program #5:

Passive Starter Defeat

Button 1 = Normal
Button 2 = Starter defeat activates 45 seconds

after ignition is turned off

Program #6:

Ignition Trigger Feature

Button 1 = Off
Button 2 = On

Default Reset

To reset all programmable features to their factory
default settings:

1. Turn ignition to the on position.

2. Wait 2 seconds.

3. Within 10 seconds press program switch 5

times. The LED and parking lights flicker to
indicate the system is now in program mode.

4. Press transmitter button 3 (Trunk).The LED

will flash 3 times,pause then continue flashing.
All programmable features will be reset to
the default position.

3