Black Widow BW 3650 Installation Manual

1

INSTALLATION MANUAL

6 RELAY SYSTEM

5-BUTTON SERIES

VEHICLE SECURITY SYSTEM

Before you begin the installation

•

Read the INSTRUCTIONS!

• Always use a multi-meter when verifying
vehicle wiring.

•

Before mounting the product,

verify with
the customer the desired location for the valet
switch and LED.

•

Protect the vehicle by using fender

covers.

•

Always look before drilling. Make sure
you will not cause damage to vehicle
hoses, electrical looms or physical damage
to vehicle.

• Set the Polarity Jumpers inside the main unit.
(see Jumper Settings)

Installation Instructions

Mounting System Module

Mount the system module under the dash
where it will be difficult for a potential
thief to locate the module, and away from
moving parts such as brake pedals, etc.

Route the antenna wire away from wire
looms, computer modules and metallic
objects for better range.

Mounting Siren

Mount the siren in a suitable place under
the hood, away from hot and moving
engine parts such as manifolds, fan belts,
etc. Make sure the siren cannot be
accessed from underneath the vehicle or
through the grill. Face the siren down so
that water cannot accumulate inside the
siren bell. Protect wires running through
the firewall using either tape or split loom
tubing. If a new hole is needed,protect the
wire from chaffing by installing a proper
size grommet.

Mounting Shock Sensor

Secure the shock sensor to the steering
column, thick wire harness or a dash brace,
using a wire tie. Make sure that the
adjustment screw is accessible for later
testing and adjustment.

2

15-Pin Main Harness:

• BLUE/WHITE WIRE - Passenger Unlock
output (-) 500mA. Connect to an optional relay
to unlock the passenger doors when the system
is configured for Driver Priority Unlocking.

• GRAY WIRE - Auxiliary 1 output (+/–) 15A
relay. Connect to an optional feature such as
trunk release, etc.

• BLACK/YELLOW WIRE - Auxiliary 3 output
(-) 500mA. Connect to a relay for an optional
feature such as headlight activation, etc.

• BLACK/WHITE WIRE - Dome Light output
(+/–) 15A relay. Connect to the wire that
activates the vehicle’s dome light, usually the
door pin switch wire. NOTE: The dome light
output is usually connected to the same wire
used for the door trigger input (See GREEN
and VIOLET door trigger wires).

• RED WIRE - +12V Battery input. Connect

the red fused wire on the main harness to a
constant +12V source.This source wire should
be at least 20 amp supply.

• BROWN WIRE - Siren wire output (+) 3A.
Connect to the siren’s red wire. Connect the
siren’s black wire to ground.

• VIOLET WIRE - Positive door trigger (+).
Connect to the door switch circuit wire that
shows +12V when the door is open. This type
of door circuit is usually found on Ford vehicles.

• BLACK WIRE - Ground input (-).Connect to
a solid chassis ground that is clean and free of
paint or dirt.

• WHITE WIRE - Parking Light output (+/-)
10A relay. Connect to the vehicle’s parking light

wire.If the vehicle’s parking light circuit exceeds
10 amps a relay is required. For vehicle’s with
independent left and right parking light circuits,
the parking light wires must be connected using
diodes to keep the circuits separate.NOTE: Do
not connect the WHITE wire to the vehicle’s
headlight circuit.

• GREEN WIRE - Negative door trigger (-).
Connect to the door switch circuit wire that
shows ground when the door is open.

• YELLOW WIRE - +12V Ignition input.

Connect to a main ignition wire at the ignition
switch harness.This wire shows +12V when the
ignition is on and while cranking. The voltage
must not drop when the car is starting.

• ORANGE WIRE - Armed Output (-) 500mA.
Connect to a relay for optional circuit defeat
(See installation diagrams).The ORANGE wire
provides a ground when the unit is armed to
activate a fuel pump disable relay or other
device (i.e. window control module, etc.).

• WHITE/RED WIRE - Auxiliary 2 output (-)
500mA. Connect to a relay or module for an
optional feature such as power window
activation or remote start, etc.

• BROWN/WHITE WIRE - Horn output (-)
500mA. Connect to an optional relay to activate

the vehicle’s horn when the alarm is triggered.

• BLUE WIRE - Trunk/Hood trigger (-). Connect
the Blue wire to the trunk and/or optional hood
pin switches.The switch must provide a ground
output when switch is opened. If the optional
remote start module is installed, connect the
blue wire to the trunk pin switch only and
connect the hood pin input on the remote start
module to the hood pin switch only.

3

5-Pin Door Lock Connector: Plug-in
connector port for door lock harness.

• WHITE WIRE - Lock relay normally closed

(87a).

• GREEN WIRE - Lock relay common (30).

• BLUE WIRE - Unlock relay common (30).

• BROWN WIRE - Unlock relay normally

closed (87a).

• VIOLET WIRE - Lock/unlock relays

normally open (87).

Starter Defeat Connectors

Using a volt/ohm meter locate the starter
wire (normally a heavier gauge wire) at the
ignition switch.This wire will show +12V only
during cranking. When this wire is cut the
vehicle will be unable to start.

Cut the BROWN starter disable wire (with
the two female connectors), and connect one
side to the vehicle’s starter wire coming from
the key switch. Connect the other BROWN
wire to the wire going to the starter.

Plug the female connectors on the BROWN
wires to the .250 male spade lugs on the
module. With the BROWN wires connected
to the module, the vehicle should be able to
start.

Plug in Connectors

2-Pin Red Connector: Plug-in connector
port for LED. Mount LED in an area where it
may be easily seen from either side of the
vehicle.

2-Pin Blue Connector: Plug-in connector
port for valet switch. Mount switch in an area
that is easily accessible from the driver’s seat.

4-Pin White Connector A: Plug-in connector
port for dual stage shock sensor.

4-Pin White Connector B: Plug-in connector
port for optional dual stage radar sensor.

Adding Transmitters

To add a new transmitter to the system have
the desired transmitters ready and follow the
Code Learning sequence.

To enter Code Learning Mode:

1. Turn the ignition on, off, on, off and leave
on.

• The siren will chirp 3 times.

2. Press and hold the Valet switch for 5
seconds.

• The siren will chirp 5 times.

3. Press the Lock Button on the transmitter.

• The siren will chirp once.

4. Press Lock Button on the transmitter
again.

• The siren will chirp twice.

5. Repeat steps 3 and 4 for each additional
transmitter.

6. Turn off the ignition.

• The siren will chirp 3 times.

Two Car Operation

With the supplied 5-button transmitter it is
possible to control a second vehicle using the
same primary transmitter. For Car 2 enter
the Code Learning Mode as described above
then substitute the steps below for 3 and 4
above.

3. Press Button 5 twice followed by the Lock
Button.

• The siren will chirp once.

4. Press Button 5 twice followed by the Lock
Button.

• The siren will chirp twice.

4

Entering Programming

To enter System Programming:

1. Turn on ignition.

2. Within 5 seconds, press valet switch 5
times.

• The siren will emit a long chirp, to

indicate entering program mode.

3. Press the valet switch the number times
equal to the desired feature.

• The siren will chirp each time the valet

switch is pressed.

4. Within 5 seconds, press the transmitter
button corresponding to the desired
operating mode for that feature.

• The siren will chirp to indicate the

setting.

One chirp = Button 1
Two chirps = Button 2
Three chirps = Button 3

5. Repeat steps 3 and 4 to change additional
features.

6. Turn off ignition to save changes.

Complete Default Reset

Following this procedure will set all
Programming Parameters to factory default
settings.

1. Enter System Programming.

2. Press Transmitter Button 3.

• The siren will chirp 6 times indicating the
reset signal was received.

• All Installer and User Programming
options are now set to factory default
settings.

3. Turn ignition off.

Programmable Features

Step

Function Button 1 (default) Button 2 Button 3

1. Siren / Horn Chirps Siren only Horn chirps Horn chirps w/Warn

2. Arming Mode Active Passive Passive w/Countdown

3. Passive Locking Off On Override Code Set

4. Ignition Locking On Off

5. Bad Zone Report 5 seconds Off

6. Auto Rearm Off On

7. Door Unlock Pulse Single Double

8. Arming Chirps Normal Silent

9. Parking Light Operation 30 seconds Flash twice

10. Trunk Disarm Feature Off On

11. Door Lock Pulse Width 1 second 3 seconds

12. Anti-Carjack Mode Manual Passive Continuous

13. Anti-Carjack Activation Disabled Enabled

14. Ignition Arming Disabled Enabled