Black Widow BW 1600 User Manual

1

OWNER’S MANUAL

PLATFORM II

Features available on your
security system:

Status indicator (red LED)
Valet / override switch
Multi-tone siren
Starter disable

(optional)

Dual stage impact detector
Remote panic
Remote chirp mute
Remote sensor/trigger bypass
Passive or active arming
Remote keyless entry

(optional)

Remote trunk or hatch release (optional)
Remote auto start (optional)
Power window roll up (optional)
Flashing parking lights (optional)
Illuminated entry (optional)
Hood and trunk protection (optional)

Note: Some features may require additional
parts and labor, and may not be appropriate for
certain vehicles. Consult your authorized dealer.

System Operation

ARMING OPERATION:

Active Arming-To activate the
alarm, simply press button #1
on your remote control,you
will hear one chirp from your
siren and your parking lights
will flash one time (optional).
Your doors will lock (optional),
and the L.E.D. will turn solid for
10 seconds then it will start
flashing slowly, the system is
now armed.

Passive Arming- If your system was installed
to arm passively, simply turn off your ignition
key and exit the vehicle, the system will arm
30 seconds after the last door is closed. After
you shut off the ignition, the LED will start
flashing rapidly to let you know that the sys­tem is in the Pre Arm state.You can always
arm the system at any time by pressing button
#1 on the remote.

DISARMING OPERATION:

To deactivate the alarm, press
button #1 on your remote, the
siren will chirp twice and your
parking lights will flash twice
(optional), then stay on for 30
seconds or until you either
turn the ignition on or rearm
the system (optional car loca­tion feature).The LED will stop
flashing, the doors will unlock

Button 1 LED Button 2

••

•

••

•

Button 2 LED Button 3

Button 1

Press

Press

2- Button

Transmitter

3- Button

Transmitter

or

Press

Press

or

••

••

•

•

••

•

••

•

(optional), your system is disarmed. If you have
the (optional) illuminated entry system
installed the interior light will flash twice then
stay on for 30 seconds or until you turn the
ignition on or rearm the system.

VALET MODE:

Valet
mode will
keep your
alarm sys­tem from
passive arming (if programmed to passively
arm), if you need to have your vehicle ser­viced, or run it through the car wash, etc. To
put your system in Valet Mode, disarm system,
turn the ignition key ON and press and hold
your valet/override switch in for approximate­ly 3 seconds, the LED will turn on solid, the
siren will chirp once. Your vehicle’s system is
in Valet Mode. If you have the keyless entry
option, the remote will still lock and unlock
the vehicle while in Valet Mode.

To exit Valet Mode:Turn the ignition key
ON, press and hold the valet/override switch
for approx. 3 seconds, the LED will turn off
and siren will chirp twice.

EMERGENCY OVERRIDE:

If you
lose your
transmit­ter, or it
fails to
operate the system, unlock the door and
enter the vehicle. The siren will sound, insert
your ignition key and turn the ignition to the
ON position. Then press the Valet/Override
Switch, the system will be overridden and
allow you to start the vehicle.The system will

automatically go into valet, so it will not pas­sively rearm. (See Valet operation to take sys­tem out of Valet mode.)

REMOTE PANIC:

For your personal safety you
may activate the siren by press­ing button# 1 on your remote
for 3 seconds.This will trigger
the system into the Panic
mode. The siren will sound and
the parking lights will flash
(optional). The panic mode will
run for 45 seconds, or until you
press button # 1 on your
remote again. This feature will not operate
when the ignition is on.

ENTRY VIOLATION MEMORY:

In the event that your system is triggered and
runs an entire cycle, when you return to dis­arm it instead of the usual 2 chirps you will
hear 3 chirps, this is to indicate that the your
system was set off; parking lights will flash 3
times as well (optional).

CHIRP DELETE:

To turn
off ARM/
DISARM
chirps,
turn igni­tion
switch
ON, then
press and
hold but­ton# 2 until you hear a double chirp. The
Arm/Disarm chirps will remain off until you
repeat the procedure.

2

Press

+

Hold

Press

3 sec.

3 sec.

or

Hold

Hold

or

ON

+

ON

+

••

•

ON

+

ON

+

••

•

••

•

••

•