Blackmagicdesign HyperDeck Extreme Control, HyperDeck Extreme 8K HDR Installation And Operation Manual

Installation and Operation Manual

HyperDeck
Extreme 8K HDR

and HyperDeck Extreme Control

July 2019

English

Welcome

When we released the original Blackmagic HyperDeck disk recorders, our dream was to allow

anyone to record and play back the highest quality video using portable SSD storage. Now we are

excited to introduce HyperDeck Extreme 8K HDR!

HyperDeck Extreme 8K HDR is a professional video recording deck that records up to 8K video

using Apple ProRes and H.265 codecs. The unit features a bright and colorful HDR touchscreen

that gives you control via tap and swipe gestures plus displays scopes for professional SDR and

HDR workflows.

You can record up to 8K H.265 on CFast cards or 8K ProRes files via external disks. If you install the

optional cache feature, media speed doesn’t matter so you can record 8K video to any Cfast card or

even connect an external HDD dock via USB-C and record to an external hard drive!

A variety of video and audio sources can be connected including decks, monitors, routers and

cameras, or legacy broadcast decks via composite analog inputs, which is especially useful for

archival workflows converting from tape to file.

We also wanted to create a deck controller that works just like a traditional broadcast deck with a

search dial and familiar controls. With HyperDeck Extreme Control, you can control your HyperDeck

Extreme 8K HDR as well as broadcast decks such as Betacam SP, Digital Betacam decks and even

1 inch machines. HyperDeck Extreme Control can control up to 8 broadcast decks via industry

standard RS-422 connections and we believe you will find the experience intuitive and efficient!

This instruction manual contains all the information you need to get started with HyperDeck

Extreme 8K HDR and HyperDeck Extreme Control. Please check the support page at

www.blackmagicdesign.com for the latest version of this manual and updates to the HyperDeck

software. Keeping your software up to date will always ensure you get all the latest features.

When downloading software, please register with your information so we can keep you updated

when new software is released. We are constantly working on new features and improvements,

so we would love to hear from you!

Grant Petty

CEO Blackmagic Design

Contents

HyperDeck Extreme 8K HDR and
HyperDeck Extreme Control

Getting Started with
HyperDeckExtreme8K HDR 4

Plugging in Power 4

Plugging in Video and Audio 5

Plugging in CFast Cards 6

Recording 7

Selecting your Source and Codec 7

Starting Record 8

Playback 9

HyperDeck Extreme 8K HDR Front Panel 10

HyperDeck Extreme 8K HDR Rear Panel 12

Touchscreen Display 15

Touchscreen Features 15

Upper Toolbar 15

Lower Toolbar 22

Settings 26

Dashboard Menu 26

Record 26

Monitor 29

Audio 31

Setup 32

LUTs 38

Storage Media 40

CFast Cards 40

EXT Disk 41

Preparing Media For Recording 41

Preparing Media on a Computer 43

Storage Indicators 45

Using the Optional Internal Cache 48

Choosing your M.2 NVMe PCIe
Flash Disk 48

Installing The Cache 48

Formatting The Cache 50

Getting Started with
HyperDeck Extreme Control 51

Plugging in Power 52

Connecting HyperDeck Extreme 8K HDR 52

Enabling Remote Control on
your HyperDeck 52

Playback using HyperDeck
Extreme Control 52

HyperDeck Extreme Control Workflow 53

Connecting your RS-422 Devices 53

Connecting your Video Signal 54

Reference Signal 54

Selecting your Devices 55

Controlling your playback
andrecord decks 55

Testing Control 56

Finding your Timecode Point
using the Search Dial 56

Using the Transport Controls 59

HyperDeck Extreme Control Front Panel 61

HyperDeck Extreme Control Rear Panel 62

Accessories 63

Rack Mounting HyperDeck 63

RS-422 Control 65

Transferring Files over a Network 71

Developer Information 72

Blackmagic HyperDeck
Ethernet Protocol 72

Protocol Commands 73

Protocol Details 76

Help 85

Regulatory Notices 86

Safety Information 87

Cache Icons and Status 50

Warranty 88

Getting Started with
HyperDeckExtreme8K HDR

This section of the manual shows how to get started using your HyperDeck Extreme 8K HDR.

Getting started is as simple as connecting power, plugging in your video and audio, inserting
a formatted CFast card and pressing the record button! You can then stop recording and play
back your files using the built in touchscreen or transport control buttons on the front panel.

However, you can also connect Blackmagic HyperDeck Extreme Control and operate your
HyperDeck remotely. This is a powerful external controller with many features including a
search dial for precise jog and shuttle control. An entire section dedicated to HyperDeck
Extreme Control is provided later in this manual.

Plugging in Power

To power your HyperDeck Extreme 8K HDR, connect a standard IEC cable to the AC power
input on the rear of the unit. You can also use the 12V DC input if you want to connect external
power or redundancy via an external power supply, for example an uninterruptible power
supply or external 12V battery.

Connec t power to the AC or DC power inputs on the rear of the unit

4Getting Started with HyperDeckExtreme8K HDR

NOTE When plugging in external power, make sure the power voltage output matches

the input voltage range marked on the rear panel.

Once powered, the touchscreen display will prompt you to select your language. To select your
language, tap on the language option followed by ‘update’. The main window will now appear.

Select your language and tap update to confirm

TIP You can change your language at any time via the setup menu. For more

information, see the ‘setup tab’ later in this manual.

Plugging in Video and Audio

There are a range of connectors on the rear of the unit so you can plug in a variety of sources,
from analog composite and component video, to SDI and HDMI.

If you want to connect an HDMI or SDI monitor, plug them into the HDMI or SDI outputs.

Audio is embedded in SDI and HDMI so you don’t have to worry about connecting audio.
However, if you want to plug in analog audio sources you can connect them via the balanced
XLR or unbalanced RCA inputs. For detailed information on all the input and output connectors,
refer to the ‘HyperDeck Extreme 8K HDR rear panel’ section of this manual.

Plug your video source into the SDI, HDMI or analog video inputs

5Getting Started with HyperDeckExtreme8K HDR

TIP HyperDeck Extreme 8K HDR automatically detects the video format and frame

rate and you can see this information displayed on the touchscreen overlay.

Plugging in CFast Cards

HyperDeck Extreme 8K HDR ships ready to record immediately. All you need is a formatted
CFast card!

You can format your CFast cards via the touchscreen LCD or via a computer. For more
information, see the ‘preparing storage media’ section later in this manual.

Using CFast Cards

The front panel features two CFast 2.0 slots for recording. CFast cards are capable
ofsupporting very high data rates, so are perfect for recording HD and Ultra HD Apple ProRes
and 8K H.265 files.

To insert a CFast card, slide it into the CFast card slot with the smaller socket facing upwards.
Apply gentle pressure until you feel it click into place. If the card is inserted incorrectly, you will
feel a solid resistance and the card will not seat.

Insert the CFast card with the card’s small slot facing upwards

To remove a CFast card, gently push the CFast card into the slot until you feel it click, then
release. The card willeject enough for you to hold the end of the card and remove it from
the slot.

That’s all there is to getting started! With the unit powered, your video source plugged in and
CFast cards formatted and inserted, you can now start recording!

Keep reading this manual to learn about all the record and playback controls on your
HyperDeck and how to change settings using the touchscreen display. You can also find
information about the connectors on the rear panel, including how to connect analog archival
video via the composite and component inputs.

6Getting Started with HyperDeckExtreme8K HDR

Recording

HyperDeck Extreme 8K HDR records video using H.265 and Apple ProRes codecs. The default
codec is Apple ProRes so you can press record straight away and record high quality 10-bit
video. If you want to record 8K video, you will need to change the codec to H.265. This section
of the manual will show you how to do that.

Selecting your Source and Codec

Change the source and codec settings using the intuitive touchscreen display.

To select a source:

1 Tap the ‘source’ icon to the right of the timecode display at the top of the touchscreen

to open the ‘record’ menu.

2 From the input options, tap the icon corresponding to the source input your video

signal is connected to, for example HDMI or component.

To select a codec:

1 From the codec options, tap on ProRes or H.265.

2 Different quality settings are available depending on the codec selected and you can

choose one by tapping the desired ‘quality’ icon. For ProRes, ‘HQ’ is the highest quality
available. If you have selected H.265, ‘high’ will record the highest quality.

To return to the main display, tap the menu icon in the top right corner. Your input and codec
selection will appear on the top toolbar of the main display along with the video source
on the LCD.

7Recording

TIP For more information on codecs and available quality settings, see the ‘codec and

quality’ section in the record menu later in this manual.

Starting Record

Now that you have set your source and codec, you can start recording.

Press the ‘record’ button on the front panel, or tap the red record icon on the touchscreen.
Youcan see your HyperDeck is recording because the record button will illuminate red along
with the timecode display and media icon. To stop recording, simply press either the
touchscreen or front panel ‘stop’ button. If you press ‘play’ while your HyperDeck Extreme is
recording, the recording will cease and playback will begin immediately from the first frame of
the recording. This means you can stop recording and start playback with the press of a
single button!

Media Warning Indicator

If you are recording Ultra HD or high quality 8K video using slower media, you may experience
problems with your media. For example, 8Krecording uses a higher data rate compared to Ultra
HD, so your CFast cards need to be the fastest available. If there are problems with your media
during recording, you will see a red exclamation icon above the audio meters on the
touchscreen overlay.

An exclamation mark will appear in the lower right hand corner of the
display if problems with your media have been detected

We strongly recommend making sure your media is on the approved media list, which can be
found in the ‘storage media’ section later in this manual.

8Recording

Cache Recording

You can avoid the risk of problems with your media completely by using the optional
cache recording feature in HyperDeck Extreme 8K HDR. This lets you record the
highest resolutions and frame rates on even the slowest media. For example, with a
cache you can record 8K ProRes HQ files onto a CFast card.

The optional cache recording feature records all files to an internal M.2 PCIe NVMe
flash disk before they are transferred to your storage media. Depending on the speed
of your storage media, this transfer can appear almost instantaneous! Abenefit of
M.2 PCIe NVMe flash disks is that they are incredibly fast, completely removing the
risk of problems even with slow recording media!

Another benefit of the cache feature is that recordings will continue even after your
connected storage media is full! When the card has no recording space left, the
recording will continue to the cache. Once a formatted CFast card or external disk
inserted, the recording will automatically start transferring to the newly inserted card.

For more information about cache recording, including how to install the M.2 PCIe
NVMe SSD, see the ‘about cache’ section later in this manual.

Playback

Once you have finished recording, simply press the ‘play’ button, or tap the play icon on the
touchscreen to start playback immediately.

You might have noticed that if you press the play button or tap the play icon more than once,
the play icon on the touchscreen changes. That is because pressing play more than once
enables the ‘loop’ feature. Looping can be helpful if you want the playback to continue looping
the same clip indefinitely, or to loop all clips on the timeline.

You can tell which loop feature is enabled by observing the play icon on the touchscreen. If it is
not the loop feature you want, simply keep pressing or tapping play to cycle it to the feature
you do want.

Loops the same clip.

After the final clip has played, playback will return to
the first clip and continue playing all clips.

To disable the loop feature, simply tap or press play until the loop icons are no longer visible.

Toggle the stop button to switch between playback and record mode

9Playback

You aren’t locked in to using the soft touch buttons or touchscreen buttons to control the
HyperDeck Extreme 8K HDR. Using the HyperDeck Extreme Control your HyperDeck
Extreme 8K HDR and 7 other remote devices at once!

For more information on HyperDeck Extreme Control, see the dedicated section later in
this manual.

HyperDeck Extreme 8K HDR Front Panel

The front panel includes soft touch buttons for easy, immediate access and an ultra bright
2000 nit HDR display to see your video in brilliant true to life colors.

1

2 4

3

1 Front Panel Speaker

The built in mono speaker on the front panel lets you check your audio levels directly
from the front panel. Simply tap on the volume meters on the bottom right of the
touchscreen display and adjust the speaker level using the slider.

5

Tap on the audio meters to display and adjust the speaker level

2 Soft Touch Buttons

HyperDeck Extreme 8K HDR features 7 soft touch buttons on the front panel so you
can quickly access traditional transport controls or apply LUTs. Each button is backlit
when the unit is powered so you can easily see the buttons when the unit is installed in
low light conditions, such as a dubbing facility.

10HyperDeck Extreme 8K HDR Front Panel

If you are using a RS-422 device to control playback and recording remotely,
press the ‘rem’ button. This will allow the your HyperDeck to be controlled
externally from a device such as the HyperDeck Extreme Control or the
HyperDeck Ethernet Protocol. The button will illuminate to indicate the remote
feature is active.

The five transport control buttons including the most commonly used functions
forrecording and playback; record, stop, play, fast forward and rewind. Use these
buttons for immediate control over the record and playback functions.

When active the selected button will illuminate.

3D LUT lets you toggle the active display LUT on the HDR LCD display.
The button will illuminate when active.

For more information on LUTs, including how to set your LUT and display it on
the LCD and or monitor out, see the ‘LUTS’ tab in the dashboard menu later in
this manual.

NOTE It is worth noting that if the unit does not have a valid signal

connected,pressing the ‘record’ button has no effect on the unit. This is the
same for the play and fast forward and rewind buttons when no storage
mediais connected.

3 Headphone Port

Connect a set of headphones to the 1/4” headphone jack on the front panel to listen to
the audio. To change the headphone volume level, tap on the volume meters on the
touchscreen display and adjust the ‘headphone level’ slider.

4 Touchscreen

The 7” LCD display features a large ultra bright HDR video display with intuitive
touchscreen controls. The wide color gamut displays both Rec. 2020 and Rec. 709
color spaces and 100% of the DCI-P3 format. You can also display full screen video
scopes. You can access all available on screen controls and menu options via the
touchscreen display!

For more information on the menu settings and using the touchscreen, see the
‘touchscreen settings’ section further in this manual.

5 CFast 2.0 Card Slots

2 CFast slots on the front of the panel for your CFast cards. LED lights to the right of the
slow indicate the media status.

Playback

Recording or while cache is transferring

Card is ready or no card is installed

11HyperDeck Extreme 8K HDR Front Panel

HyperDeck Extreme 8K HDR Rear Panel

8

14

11

6

7

9

15

17

16

10

12

13

6 Power

There are two power options on the rear, an AC power input for IEC mains power input
as well as a 12V 4 pin XLR DC input for connecting redundancy or battery power.
Ensure any DC power source connected to the units is compatible with the input
voltage and current rating marked at the DC IN connector

7 Analog Input

Connect analog sources for archiving via the analog stereo left and right RCA
connectors, the single BNC composite input or via the component in.

8 Remote

There are two RS-422 DB9 connectors for remote in and out.

9 USB

Use the USB-C connector with the white surround for software updates via a computer
using the HyperDeck Setup Utility.

10 Ethernet

A 10Gb/s ethernet connection lets you connect directly to your network for fast ftp
transfers or to remotely control the unit via the HyperDeck Ethernet Protocol.

Connect it to the same network as an ATEM Switcher and you can use your HyperDeck
for playback using the HyperDecks palette in ATEM Software Control or via an
ATEM broadcast panel. For more details on transferring files via an FTP client, see the
‘transferring files over a network’ section later in this manual.

11 Time Code

Receive external timecode via the XLR timecode inputs or loop out timecode via the
XLR timecode out connection. For more information on how to select your timecode
options, see the ‘setup’ menu later in this manual.

12 Ref

Your HyperDeck Extreme 8K HDR features a stabilized video reference output
corresponding to standard definition black burst and high definition tri-sync standards.
You can also receive reference signals from external sources such as a sync generator.

12HyperDeck Extreme 8K HDR Rear Panel

This means you can have multiple devices in your facility receiving a reference signal
from a single source, such as the Blackmagic Sync Generator, to genlock all your
equipment together! Select between the input and external reference source via the
touchscreen setup menu.

For more information on selecting your reference source, see ‘setup’ settings later in
the manual.

13 HDMI

The HDMI connections are perfect for when you’re using the unit as a field recorder
and connecting to an HDMI enabled display for playback. For signals from standard
definition to 2160p60, the HDMI input will auto detect SDR and HDR video standards
when the signal is flagged with the correct metadata. This means you can display
stunning HDR images on HDR enabled HDMI screens using the HDMI out.

14 Analog Audio

You can connect up to 4 channels of balanced analog audio in or out via 3 pin XLR
connectors. Select your audio input using the ‘audio’ tab in the dashboard menu.
See the ‘audio’ section later in this manual for more information.

15 Monitor Out

An 3G-SDI monitor out connection provides a downscaled output with overlays so that
you can monitor on an external display. The overlays include focus and exposure tools
such as grid and false color that you can toggle on and off as well as drive icons, audio
meters and a time counter display. For more information on the Monitor SDI settings,
including how to output a clean signal, see the ‘monitor’ page in the dashboard menu
later in this manual.

16 Ext Disk

Connect a flash disk to the USB-C connector on the rear so you can record to external
disks at up to 10Gb/s. You can also connect to multi port USB-C hubs or the MultiDock
10G allowing you to connect one or multiple SSDs for far greater storage capacity!
Recording to high speed SSD’s and hard drives reduces the risk of problems with your
media compared to CFast 2.0 cards. For more information on external disks, see the
‘storage media’ section later in this manual.

17 12G-SDI Digital Video

Featuring four 12G-SDI inputs and outputs on the rear for video signals from standard
definition to Ultra HD via a single cable, 8K30p via dual link 12G-SDI and up to 8K60p
via quad link 12G-SDI.

Using the quad link 12G-SDI connections you can use HyperDeck Extreme in 8K
workflows. Connect it to ATEM Constellation 8K as a playback or recording device that
can be accessed via the HyperDecks palette in ATEM Software Control

13HyperDeck Extreme 8K HDR Rear Panel

Connect your 4 12G-SDI cables from the input or output on the HyperDeck Extreme to

AA BB AA BB

CC DD CC DD

AA BB AA

8K

BB

CC DD CC DD

one of the 8K inputs or outputs on the rear of the ATEM Constellation 8K. It is important
to connect your quad link SDI cables in the correct order. For example, connect the
SDI input or output labelled ‘c’ on HyperDeck Extreme to the third input or output on
the ATEM Constellation 8K.

Plugging the 8K quad link SDI output of a HyperDeck Extreme 8K
HDR into the SDI input of the ATEM Constellation 8K.

Two Sample Interleave

There are two different methods for 8K workflows; two sample interleave and square
division. HyperDeck Extreme 8K HDR and ATEM Constellation 8K both use two
sample interleave, known as 2SI. With 2SI, each 12G-SDI connection delivers an 8K
signal at 1/4 of the resolution. When combined, you have a full resolution 8K signal!

A benefit of the 2SI method is that if one of the 4 connections become loose, you will
only lower the resolution rather than lose one corner of the image, as would be the
case in a square quadrant setup.

If your 8K workflow involves devices using the square division method, your can use
Teranex Mini SDI to HDMI 8K HDR to convert automatically from 2SI to square division.

14HyperDeck Extreme 8K HDR Rear Panel

Touchscreen Display

Touchscreen Features

The interactive touchscreen display lets you view and select options directly from the screen

The intuitive 7 inch display lets you view and select many of the HyperDeck Extreme functions
directly from the touchscreen display.

The display includes an upper and lower toolbar. These toolbars display settings and status
information, for example the current source, or the clip currently being recorded or played.
Settings can also be adjusted by tapping on their relevant icons, for example to change the
source, tap on the ‘source’ icon, then tap on one of the source options.

Indicators show the current status for items such as the source video format and frame rate,
timecode, media record time remaining, audio levels and transport controls.

The lower toolbar can be hidden or revealed by swiping the touchscreen up or down.

Upper Toolbar

Tap on ‘monitor overlay’ or the audio meters for immediate access to available settings with
slider controls to adjust speaker levels and select focus assist tools.

Navigate directly to the related menu options by tapping ‘source’ or ‘codec’. Selecting your
active drive for recordings and playback is done by tapping anywhere on the drive icons.

Monitor options

Tap on the monitor icon on the left to access the monitor overlay settings. These settings let
you select and modify the appearance of overlay options including zebra, focus peaking,
guides, grid, false color, contrast, brightness and saturation. This is especially useful when using
the HyperDeck Extreme 8K HDR as a field recorder.

Zebra

Zebra mode will help you to achieve the optimum exposure by displaying diagonal lines
over the areas of content that exceed the set zebra level. To enable zebra mode, toggle
the switch to on. Use the slider or the arrows to the left and right of the percentage icon
to select your zebra level. A level of 100% will mean any area of the image displaying
diagonal lines is overexposed.

15Touchscreen Display

Use the slider or arrow to select your zebra percentage

TIP You can also set the zebra to highlight areas of your image that represent

specific video levels on a waveform, for example setting the zebra for 50%
means you can visually identify which regions of your image will appear at
approximately 50% on a waveform scope.

Focus Assist

Focus assist gives you powerful tools to help focus your image fast. Focus assist
displays edge lines on the sharpest areas of the image. To turn on focus assist, toggle
the switch to on. Sensitivity settings let you change how strong the lines are from ‘low’,
‘medium’ or ‘high’. In images with lots of detail and high contrast, the lines can be
distracting, so in these conditions you can select ’low’ or ‘medium’.

Alternatively, for low contrast shots with less detail, select ‘high’ so the lines are
stronger and easier to see. If you find lines are too visually intrusive, you can select
‘peak’ levels instead. For more information on how to set peak levels, see the ‘monitor’
settings later in this manual.

Frame Guides

Guides provide a range of aspect ratios from various film, television and online
standards. Tap the toggle switch to on and then select your guide by tapping the left
and right arrows or by dragging the slider control.

16Touchscreen Display

Grid

The grid view display provides three overlays to assist with shot framing. There are
three different views available on the HyperDeck Extreme 8K HDR to assist with
shot framing.

Thirds Thirds will overlay two horizontal and two ver tical lines over your image,

breaking it up into 9 smaller sections to help you compose your shot.
Thehuman eye typically looks for action near the points where the lines
intersect, so it’s helpful to frame key points of interest in these zones.
An actor’s eyeline is commonly framed along the top third of the screen,
soyou can use the top third to guide your framing.

Crosshairs The ‘crosshairs’ setting places a crosshair in the center of the frame.

Like thirds, the crosshairs is a very useful compositional tool, making it easy to
frame the subject of a shot in the very center of a frame. This is sometimes
used when filming scenes that will be assembled using very fast cuts.
Keeping viewers’ eyes focused on the center of a frame can make rapid editing
easier to follow.

Center Dot The ‘center dot’ setting places a dot in the center of the frame. This works in

exactly the same way as the ‘crosshair’ setting, albeit with a smaller overlay
that you may find less intrusive.

You can enable a combination of ‘thirds’ and ‘crosshairs’ or ‘thirds’ and ‘center
dot’ by tapping both options in the ‘grids’ menu. ‘Crosshairs’ and ‘center dot’
cannot be selected together.

17Touchscreen Display

False Color

The ‘false color’ setting toggles the appearance of false color exposure assistance on
the LCD touchscreen and the SDI monitor out. When false color is on, different colors
are superimposed over your image to represent different exposure levels. For example,
optimal exposure for skin tones can be achieved by using green for dark shades and
pink for pale shades. Monitoring the colors during recording can help you maintain
consistent exposure for skin tones. Similarly, when elements in your image change from
yellow to red, that means they are now over exposed.

TIP Zebra, focus peaking, guides, grid and false color can be toggled on or

off via the ‘monitor settings’ in the dashboard menu. You can also toggle the
overlays for the 3G-SDI Monitor output. See ‘monitor settings’ later in this
manual for more information.

The three remaining monitor settings alter the LCD display settings.

Contrast Adjust the contrast of the HDR display to increase or decrease the

range between the brightest and darkest parts. A high contrast
image can reveal detail and depth in the image, low contrast can
make the image appear soft and flat.

Brightness Adjust the brightness of the display by dragging the slider to the

left to make the imagedarker, or the right to make it lighter.
Changing the display brightness can make it easier to see images
when the HyperDeck Extreme 8K HDR is in extremely bright or
low light locations.

Saturation Use the saturation slider to increase or decrease the amount of

color in your displayed image.

NOTE All settings will be kept when the unit is powered off. It’s also worth mentioning

that the use of monitor options will affect the image displayed on the LCD display, but
not your recorded video.

18Touchscreen Display

Codec

The codec icon displays your currently selected ‘record’ codec or the ‘playback’ codec of the
file currently playing. You can select a new codec for recording by tapping the codec icon and
selecting from the menu options displayed on screen. For more codec information, see the
‘record settings’ section later in this manual.

Format

When in playback mode, the ‘format’ icon will display the current clips resolution and frame rate.
If you are in ‘record’ mode, it will display the resolution and frame rate of the current source
selected. If ‘no signal’ appears, it means a valid signal is not detected.

Timecode

A large timecode view at the top displays either SMPTE timecode or a timeline time counter.
Simply toggle between the two by tapping anywhere on the timecode icon.

SMPTE timecode mode is indicated by a ‘tc’ icon to the right.

The time counter displays the timeline timecode.

The timecode display will appear red while the unit is recording in both
timecode and timecounter modes.

If you don’t have a valid timecode source, the timecode for each
recording will begin at 00:00:00:00.

The timecode view display SMPTE timecode or time counter.

Source

The source icon displays the current source input you have selected on the HyperDeck
Extreme 8K HDR. Tap on the source icon to open the record menu where you can select from
SDI, HDMI, Component and Composite.

Cache

If you are using the optional cache feature, you can see at a quick glance the storage remaining
and status of the cache by looking at the cache icon. When a M.2 PCIe NVMe disk in installed
and formatted, the cache icon will display willdisplay the remaining space on the drive. When a
valid video signal is detected, the remaining space will be displayed in hours:minutes:seconds
based on the current format and your selected codec. When no valid signal is detected, the
remaining space available will be listed in TB or GBs.

If there is no SSD installed, the icon will display ‘no cache’. For more details on using the
optional cache feature, see the ‘Using the Optional Internal Cache’ section later in this manual.

19Touchscreen Display

Video Scopes

Tap on the video scopes icon to display the video scope options.

Tap on the scopes icon to reveal the different video scopes you can view

There are 4 different video scopes to choose from:

Waveform The waveform monitor is a graphical representation of the image, showing luma values in

the same position relative to those within the frame. For example, if part of your sky is
overexposed you will see it in the same horizontal position on the waveform display as it
appears in the frame.

Parade The real time RGB parade waveform view is the ideal scope for accurate color correction.

The parade view separates the value of each channel so that you can identit y which colors
represent each brightness.

Vector A vectorscope is the only way to measure colors in video accurately. If you’re color

correcting video, vectorscope shows when color has been removed or nulled out for
accurate white balance. When you need to apply a tint, the vectorscope lets you see exactly
how much tint you’re adding and what color it is.

Histogram Histogram view lets you see where the pixels are in your video, and how they are

distributed from black to white. You can see if your video is clipping and adjust the camera
iris and ISO settings to keep all black and white detail in the image. This means you have
the full contrast range of video for easy color correction during post production.

To disable the scopes and return to your full screen video view, select ‘video.’

When selecting any of the video scopes, you can click on the settings icon to display brightness
and opacity sliders allowing you to alter the view of the scopes and adjust how they appear
over the footage. Altering the opacity can assist in reading the scope information depending
onyour source video.

20Touchscreen Display

Adjust the opacity of the background by using the slider adjustment

Scope Brightness

You can control the brightness of the white scope graphic from 0% to full brightness at
100%. This can help you find areas of fine detail that may not be so clear with a low
scope brightness.

Background Opacity

Each video scope has a black background. You can modify the display of this
background from invisible at 0% to completely black at 100%. The higher the opacity,
the darker the background, which will make your video appear and the graticules clear.

NOTE It is worth noting that each of the video scope options feature an

orange graphic element displaying your levels. Modifying your scope
brightness or background opacity has no impact on the display of these
orange graphics.

Picture in Picture

When a video scope is active, a small ‘mini preview’ icon will appear at the top right of
the scope.

Tap on the ‘mini preview’ icon to display your video in a small preview window

You can use the picture in picture option to minimize the video to a small preview
window that can be moved around the display to your preferred location.

21Touchscreen Display

TIP If your video scopes aren’t appearing when you switch them on, make sure

‘scopes’ is enabled in the monitor page of the dashboard menu. For more information,
see the ‘monitor settings’ section later in this manual.

Menu

The last icon on the top row is the menu icon where you can access the dashboard menu.
This dashboard menu is where you can access to all the recording options including source and
codec, audio channels, monitor options audio preferences and more.

Tap on the menu icon to open the dashboard menu.

For more information on menu options available, see the ‘dashboard’ section later in
this manual.

Lower Toolbar

Transport Controls

The first five icons on the bottom left of the display are your touchscreen transport controls.
Thefunction of these buttons can depend on whether you are in ‘record’ mode or
‘playback’ mode.

The ‘record’, ‘play’ and ‘stop’ buttons work just like they do on the front panel.

To start recording, tap the ‘record’ button once and both the touchscreen and front
panel record buttons will illuminate red. To stop recording, tap the ‘stop’ button.

To view your recently recorded clip, tap the ‘play’ button. You will now be in ‘playback’
mode. The touchscreen ‘play’ button will illuminate blue and the soft touch play button
on the lef t of the front panel will illuminate green.

Pressing ‘stop’ will stop the HyperDeck Extreme recording. If you press ‘stop’ while in
playback mode, playback will stop and a clip timeline will appear above the transport
controls. Similar to a timeline in editing, it’s a visual representation of all the clips on
your timeline with a playhead indicating your current playback position.

22Touchscreen Display

The time counter to the left of the timeline bar displays the current location of the playhead and
the time counter to the right displays the total duration of all clips.

You can navigate along the timeline by tapping the ‘skip’ back and ‘skip’ next icons.

Tap the skip back button once to move the playhead to the f irst frame of the current clip.
If the playhead is already on the start of a clip, it will jump to the first frame of a previous
clip. You can also use the skip buttons to enter shuttle mode for greater playback speeds.

Press and hold either of the skip buttons down until the icon changes to a blue with two
arrows. Now you can use can change the playback speed from x1/2 up to x50 speed by
either holding down the button or tapping it to change the speed in set increments.
To reduce the speed, simply press the shut tle button in the other direction.

To exit shuttle mode, simply press either the ‘stop’ or ‘play’ buttons and the buttons will revert
to the skip forward and skip backward icons. When in shuttle mode, you can increase shuttle
speed by tapping the shuttle forwards or backwards buttons more than once. To decrease the
speed, tap on the alternative shuttle button.

For example, when shuttling forwards at an increased speed, tap the shuttle backwards button
to decrease the speed. This lets you avoid using the stop button, which will take you out of
shuttle mode.

When using the fast forward shut tle mode, press the rewind icon
to stop playback but remain in shuttle mode.

To leave playback mode, press ‘stop’ once to stop playback and ‘stop’ again to return to
record mode.

NOTE It is worth noting that when in record mode, pressing the skip buttons

performs no action.

23Touchscreen Display

Clip Name and Transport Status

During playback only the top and bottom toolbars will be in view. When playback is paused or
you are playing at greater than real time speed, the transport status will appear on the top right
hand side of the display. The clip name will be visible on the top left of the display so you can
see at a quick glance exactly what is playing and its transport status.

The clip name and transport status can be hidden from the display by setting the clean feed to
‘on’ in the monitor menu or by swiping the display up or down to remove the lower menu bar
out of view. For more information on clean feed, see the ‘monitor’ settings section later in
this manual.

Swipe the display up or down to remove the lower toolbar and timeline

Touch and Swipe Controls

You can also use touch and swipe gestures to jog through your clip for precision control over
playback down to the frame!

Tap on the timeline and the playhead will immediately move to the location of your finger.

To scrub through the footage, drag the playhead to the left and right along the timeline.
The playhead will move to the location of your finger.

For precision jog movements, simply swipe your finger on the video above the timeline and
below the top toolbar. The speed adjusts to your momentum, meaning the faster you swipe,
the faster the playhead will move!

Swipe lef t of right for precision control

24Touchscreen Display

Storage Indicators

The storage indicators display the status of the media slots including record duration available.
The first two icons represent 2 CFast card slots on the front panel. The third drive icon displays
the active USB flash disk connected via the ‘ext disk’ connector on the rear of the HyperDeck
Extreme 8K HDR.

On screen icons let you see the status
of your storage at a quick glance

Your active drive is used for playback and recording. Once a drive is filled, recording will spill
over to the next drive, ensuring you don’t miss a frame.

For more information on storage indicators, see the ‘storage media’ section later in this manual.

Audio Meters

On screen audio meters display the first four audio channels of any source. To display larger
meters, tap on the audio meter icon. The meters will now appear over the video. Labels to the
right of each channel identify the type of meter, for example PPM or VU.

The audio meters will display your current
audio as a VU or PPM audio monitor. Tap
on the audio meters to adjust levels

When in record mode you can adjust the levels of XLR audio using the sliders beneath
each channel.

When in playback mode, you can use the slider beneath each channel to adjust the XLR audio
output levels. Idle or disable audio channels will be grayed out.

The audio meters will display your current audio via a VU or PPM
audio monitor. Disabled audio tracks will be grayed out

You can select your meter type via the setup tab in the dashboard menu. See the setup section
in the dashboard menu later in this manual.

25Touchscreen Display

Settings

Dashboard Menu

Pressing the ‘menu’ icon on your HyperDeck Extreme 8K HDR will open the dashboard menu.
This is a tabbed menu containing the settings not available from your HyperDeck’s front upper
and lower toolbars.

Settings are divided by function into ‘record’, ‘monitor’, ‘audio’, ‘setup’ and ‘LUTs’. Dots at the
bottom of the menu let you know when a tab contains multiple pages. You can navigate
between by swiping the touchscreen display to the left or right or by tapping on the arrows.

Return to the full screen view at any time by tapping
on the ‘dashboard menu’ icon at any time

Record

Record Page 1

Use the ‘record’ tab to select your input and
choose your codec and quality settings

26Settings

Input

Once your sources are connected, you can select your input via the ‘record’ settings
tab. The four options represent each type of connection and it’s as easy as tapping the
button to select the input. For SDI connections from standard definition to quad link 8K,
tap on ‘sdi’. For analog devices attached via the component YUV connections, such as
a Beta SP deck, tap on ‘component’.

Codec and Quality

With HyperDeck Extreme 8K HDR, you can record compressed video using Apple
ProRes or H.265 codecs. For each codec, there are different quality settings you can
choose to record to.

ProRes When ProRes is selected, there are three options available: HQ, 422 and LT.

Choose HQ for times when you need to record the highest qualityavailable and
therefore larger file sizes. When you want your recordings to take up less space,
you can choose ProRes LT which has ahigher compression and therefore smaller
overall f ile size.

H.265 If you select H.265 as your recording codec, there are three different compression

settings available: high, medium and low. High quality is the perfect choice for
when you want the highest quality with the least amount of compression. Low
provides a much smaller file size as the file is morecompressed.

When selecting your codec, it’s important to take into account what storage media your
are recording to. For CFast cards, you can record up to 8K using H.265 or up to 4K
using ProRes HQ. When recording to external disks such as a USB-C flash disks, you
can record 8K in any codec. With the optional cache installed, all codec and quality
options are available for 8K recording.

NOTE HyperDeck Extreme will play back H.265 files recorded on a

HyperDeck Extreme, but not H.265 files recorded on other video equipment.

27Settings

Record Page 2

Additional settings on the second record page

Trigger Record

There are two trigger record modes available, video start/stop and timecode run.
Somecameras, such as the URSA Mini, send a signal over SDI to start and stop
recording on external recorders. Tapping on ‘video start/stop’ will trigger the
HyperDeck Extreme to start or stop recording when the record button is pressed on
the camera.

You can use the time ‘timecode run’ option to trigger the unit to start recording when it
receives a valid timecode signal via the inputs. When the signal stops, recording will
also stop. You can disable trigger recording by tapping the ‘none’ option.

Select ‘none’ to disable trigger recording

Record Audio Channels

HyperDeck Extreme 8K HDR can record up to 16 channels of audio at a time. Select
how many channels you wish to record by tapping 2, 4, 8 or 16 channels. If you are
recording 4 channels or less, you can adjust the input volume level by using the
adjustments meters on the audio tab or the onscreen audio meter settings. For more
information, see the ‘audio settings’ section later in this manual.

Tap on 2, 4, 8 or 16 channels to select the
number of audio channels you want to record

28Settings

Monitor

The ‘monitor’ tab lets you toggle the monitor options as well as Display 3D LUT and Scopes.
These can be toggled on or off for the LCD display and SDI monitor out.

Tap on LCD or SDI to toggle the options on or off

Monitor Settings – LCD tab and Monitor SDI tab

Display options can be toggled on or off for the LCD screen and SDI output feed individually
using the LCD or Monitor SDI tab.

These include:

Clean Feed

Turn clean feed ‘on’ to disable all status text and overlays for the LCD display and
monitor SDIoutput. This option is a quick way to turn off all the outputs at once.

Zebra

Tap the ‘zebra’ setting on to enable zebra guides. When your zebra guides are on,
diagonal lines with appear to let you know what areas may be clipped. See the
‘touchscreen menu’ in this manual for information on how to set the zebra guide levels.

Focus Assist

Toggle on ‘focus assist’ on the LCD or monitor SDI output to view the focus assist
overlay lines. Focus assist type and color settings can be in the ‘LCD and SDI’ menu.

Guides

To see frame guide overlays for different film, television and online aspect ratios, toggle
on frame guides. Choose your desired guide from the front panel display by tapping on
the ‘monitor overlays’ icon.

Grid

To see one of three grid options to assist with framing, toggle ‘grid’ on. Grid options
include thirds, center dot and crosshair. Toggle grid on or off. To set the desired grid,
tap on the menu icon in the top right corner to return to the LCD display and tap on the
‘monitor overlays’ option.

False Color

The ‘false color’ setting toggles the appearance of false color exposure assistance on
the LCD touchscreen. For more information, see the ‘false color’ section in the
‘touchscreen menu’ in this manual.

29Settings

Display 3D LUT

Toggles display LUTs on and off to your LCD or monitor SDI. The toggle appears
disabled when no LUT is active. For information on how to set a LUT, see the LUTs
section later in this manual.

Monitor Settings – LCD and SDI

The LCD and SDI setting features controls for focus assist
as well as options for anamorphic displays

You can adjust the appearance of focus assistance settings using the ‘LCD and SDI’ tab. These
options affect the look of for both the LCD display ad the SDI monitor output.

Focus Assist Type

There are two focus assist modes, ‘peak’ and ‘colored lines’.

Peak When you select focus peaking the areas within your frame with the highest

contrast will be highlighted.

Colored Lines If colored lines is selected, lines will be super imposed over any part of the

image in focus. This can be a more visually intrusive than using ‘peak’.

Focus Assist Color

When you are using colored lines for focus assistance on your LCD display or
SDI monitor out, you can select your preferred color for the lines from red, blue, white
or green. Changing the color can help to make your area of focus stand out more.

Anamorphic De-squeeze

The anamorphic de-squeeze option allows you to correctly display horizontally
squeezed images from any anamorphic sources, such as digi-beta tapes containing
anamorphic 16:9 content or anamorphic lenses. Tap ‘none’ for non anamorphic sources.

30Settings

Audio

Audio Page 1

The audio input displays audio meters for embedded, XLR and RCA audio inputs. You can
select to display PPM or VU Meters. To change your meter type, see the ‘setup’ settings later in
this manual.

Video Click on the video tab for audio embedded in SDI and HDMI signals. If you

have selected 2 channels ofaudio on the record tab, only the top two
channels will be active.

XLR When recording audio from an XLR input, you can change the input level using

the slider beneath each channel.

RCA If you are using audio connected via RCA, only channels 1and 2 are active.

Audio Page 2

Swipe the audio tab left or right to reveal the XLR output audio meters screen to navigate to the
XLR output controls. You can adjust the levels for all four XLR outputs. Adjust the level by
dragging the slider beneath each channel to the left to reduce the output volume, or to the right
to increase the volume. The type of audio meter displayed depends on the meter selected in
the setup tab. XLR audio outputs can be used to connect audio to other devices such as the
ATEM Constellation 8K switcher.

Adjust the XLR Output channels using the slider beneath

31Settings

Setup

The setup tab provides access to network, timecode and reference settings as well as your
audio meters.

Setup Page 1

Add your HyperDeck Name and network settings on the Setup tab

HyperDeck Name

Change the name of the unit by clicking on the pencil icon to the right of the name.
It can be especially useful to name your device when you have more than one
HyperDeck Extreme 8K HDR on your network for easy identification. The name is also
displayed on the SDI Monitor out too.

Date and Time

Set your date and time by clicking on the pencil icon. The date edit screen will appear.

Use the arrows to change your date and time

Tap the arrows either side of each setting to select your year, month and day. Repeat
the process to set your hour, minute and time zone. Press update to save the settings.

Software

Displays the current software version.

32Settings

DHCP

To connect to your network via a dynamic IP address, toggle the switch to on.
Tomanually set a static IP address, toggle it to off.

IP address

When DHCP is switched ‘off’, you can enter your network details manually. Click on the
pencil edit icon. Enter the IP address into the numeric keypad view. Once you have
entered your address, press the ‘update’ button.

When you edit any numeric option, a numeric keyboard will appear.
Type in the address and press update to confirm.

Gateway

Set your network gateway address by clicking on the pencil icon to open the numeric
keypad. Press update to return to Setup page 1.

Subnet Mask

Your subnet mask can be manually entered by clicking pencil edit icon. Once you have
entered your address, click the update icon to return to the menu.

Setup Page 2

Set your timecode settings on the second setup page

33Settings

Timecode Input

There are four timecode input options available when recording.

Video Input Selecting video input will take the embedded timecode from SDI and HDMI

sources with embedded SMPTE RP 188 metadata. This will maintain sync
between your SDI or HDMI source and the file recorded on the HyperDeck
Extreme 8K HDR.

External XLR Click this option when using timecode via external XLR from analog

basedsources.

Last Clip Regen By selecting ‘last clip regen’ for your timecode input, each file will start one

frame af ter the last frame of the previous clip. For example, if your first clip
ends on 10:28:30:10, the nex t clip timecode will start at 10:28:30:11.

Preset Preset will use the set timecode under ‘timecode preset’.

Timecode Preference

For NTSC sources at frame rates of 29.97 or 59.94, you can select ‘drop frame’ or
‘non-drop frame’ recording. For sources with frames rates of 29.97 or 59.97, tap on
default. This will maintain the standard of the input, or default to drop frame if there is
no valid timecode.

Timecode Preset

You can set your time code manually by tapping on the pencil icon and entering the
start time code via the touchscreen keypad.

Timecode Output

Tap on clip or timeline to select your timecode output

Select your timecode options for your SDI outputs.

Timeline Tap the timeline option to output your timeline timecode.

Clip The clip option will output the timecode of your clip.

Setup Page 3

34Settings

Reference Source

Select your reference source from the two options.

Input Select ‘input’ if your source has embedded reference that you want to

sync to. An example of this would be where your tape based deck may
have a genlock source directly connected.

External If you have an external reference device, for example the Blackmagic

Sync Generator, connected via the ‘ref in’ connection on the rear,
select ‘external’.

3G-SDI Output

Some broadcast equipment can only receive level A or level B 3G-SDI video.
Tomaintain compatibility, tap either ‘level A’ or‘level B’.

Tap ‘level a’ or ‘level b’

Reference Timing

If you are archiving from analog based tape decks, you may find you need to adjust the
reference timing for accurate color representation. This is especially the case if you
don’t have avalid reference signal. The reference adjustment lets you adjust the timing
of the video outputs of your hardware relative to the video reference input. This is
commonly used in large broadcast facilities where the video output needs to be
accurately timed. The reference adjustment is in samples so you can get an extremely
accurate timing adjustment down to the sample level.

Adjust the number of lines and pixels by tapping the tapping the arrow to the left to
decrease or the arrow to the right to increase.

Tap on the arrows to increase or decrease your timing lines and pixels.

Playback Dynamic Range

To change your playback dynamic range to match your source, tap on the arrows to the
left and right.

35Settings

Available dynamic ranges include:

Auto

Rec. 709

Rec. 2020 SDR

HLG

ST2084 300

ST2084 500

ST2084 800

ST2084 1000

ST2084 2000

ST2084 4000

ST2084

Setup Page 4

The last page of ‘setup’ includes audio meter settings and filename options

Audio Meters

You can choose from two different audio meter display types.

VU The VU meter, or ‘volume units’ meter, averages out short peaks and troughs in

your audio signal. If you are using VU metering, adjust the input levels on the
HyperDeck Extreme 8K HDR so that the meter peaks at the 0db indicator on the
audio meter. This maximizes the signal to noise ratio and ensures your audio is at
the highest quality. If your audio peaks beyond the 0dB indicator there is a high risk
of sound distortion.

PPM PPM meters, or ‘peak program meters’ displays a ‘peak hold’ feature that

momentarily holds the signal peaks and a slow fall back so you can easily see
where your audio is peaking.

Both VU and PPM meters are available at reference levels of -18dB or -20dB so you can
monitor your audio to suit different international broadcasting standards.

To adjust your input levels on the ‘touchscreen display’, tap on the audio meter in the
bottom right corner. For more information, see the ‘audio monitor’ section under
‘touchscreen controls’ in this manual.

36Settings

Filename Prefix

When first set up, your HyperDeck Extreme 8K HDR will record clips to your CFast or
USB Flash disk using the following filename convention.

Untitled_0001

Untitled_0001 Filename

Untitled_0001 Clip Number

You can edit the filename of your recorded files by tapping the ‘edit’ pencil icon.
A touchscreen keyboard will appear. Type in the filename.

Timestamp File Suffix

The timestamp added to the filename is turned off by default. If you would like the date
and time recorded in your filename, toggle the ‘timestamp file suffix’ option to on.

Untitled_1904061438_0001

Untitled_1904061438_0001 Filename

Untitled_1904061438_0001 Year

Untitled_1904061438_0001 Month

Untitled_1904061438_0001 Day

Untitled_1904061438_0001 Hour

Untitled_1904061438_0001 Minute

Untitled_1904061438_0001 Clip Number

Language

HyperDeck Extreme 8K HDR supports 11 popular languages including English, Chinese,
Japanese, Korean, Spanish, German, French, Russian, Italian, Portuguese and Turkish.
The language page will also appear on initial start up.

To select your language:

1 Tap on the ‘language’ and select your language from the list.

2 Select ‘update’ to return to the setup menu.

37Settings

Factory Reset

Tap on ‘reset HyperDeck’ to restore your HyperDeck to factory settings.

Setup Page 5

Analog Input NTSC IRE

For analog NTSC inputs, select between 0.0 IRE and 7.0 IRE depending on the region
you are working in.

Analog Input Levels

When you have selected component video, you can switch between SMPTE and
Betacam levels. SMPTE levels are more common, and even Betacam SP can use
SMPTE, so only switch to Betacam if you are sure that Betacam levels are being used.

LUTs

Display LUTs can be especially helpful when using the HyperDeck Extreme as a field recorder.
They work by telling the unit what color and luminance output to display. This can be useful for
when you are using the ‘film’ dynamic range on your camera which has an intentionally
undersaturated, ‘flat’ appearance. By applying a display LUT, you can get an idea of what your
video will look like after it has been graded.

38Settings

Display LUTs can be applied for the LCD display as well as the SDI monitor out. To view a LUT
you first need to select your active LUT. In the LUT menu, tap on the LUT you want to use, it will
highlight blue. Tap the tick icon at the bottom. A vertical blue line will appear to the left of the
LUT name to confirm the LUT is active.

You can now press the ‘3DLUT’ button on the front of the panel to display the selected LUT.
The button will illuminate when selected. Press the button again to toggle it off.

TIP You can also toggle the display LUT on the LCD and Monitor SDI via the ‘Monitor’

tab in the touchscreen menu. For more information, see the ‘monitor’ settings in the
dashboard manual

You are not limited to using the preloaded display LUTs either, you can import or
export your own!

To import a LUT:

1 On the LUTS tab, tap on the double head arrow icon at the bottom center of the display.

2 Under manage LUT, tap on ‘import LUT’.

3 Select the storage media where the LUT is located and tap ‘import’.

Select the location of your stored LUT and tap import.

4 Tap on the LUT you want to import followed by ‘import’. A progress screen will let you

know the LUT is importing. Once done, the LUT will appear in the list.

39Settings

The LUT will now appear in the list and once you make it active your can apply it to the LCD and
external monitor.

NOTE If you try to import a LUT that already exists, a screen will prompt you to either

keep both or replace the existing LUT.

Storage Media

The HyperDeck Extreme 8K HDR can record to CFast cards via the two front panel slots or
external storage connected via the rear USB-C port. With Blackmagic MultiDock 10G, you can
have 4 SSD’s connected at once!

Depending on your workflow and desired recording resolution, you may already have CFast
cards or external disks fast enough to use. For example, standard definition workflows, such as
archiving from Digital Betacam to file, will not require the fastest media. For workflows recording
the highest resolutions, such as 8K video, media with higher write speeds is required.

TIP The following approved media is based on recording 8K video to HyperDeck

Extreme without the optional cache installed.

CFast Cards

When working with high data rates it is important to carefully check the CFast card you would
like to use. This is because CFast 2.0 cards have different read and write speeds. The tables
below identify the CFast cards recommended for use.

Choosing a CFast 2.0 Card

The following CFast 2.0 cards are recommended for recording 8K Apple ProRes LT up
to 60 fps.

Brand Card Name Storage

Wise CFast 2.0 3500X 512GB

Wise CFast 2.0 3500X 1TB

The following CFast 2.0 cards are recommended for recording 8K H.265 High up to 60 fps.

Brand Card Name Storage

Cinedisk Pro CineDisk Pro 510MB/s 256GB

KomputerBay KomputerBay 3600X 64GB

ProGrade Digital ProGrade Digital 550MB/s 128GB

ProGrade Digital ProGrade Digital 550MB/s 256GB

ProGrade Digital ProGrade Digital 550MB/s 512GB

40Storage Media

NOTE Slower CFast cards are compatible when the optional cache is installed. This is

because the cache can accept overflow data when the card cannot keep up. However,
it might take a few minutes for the cache to f inish copying to the card when recording
stops, depending on the speed of the media card.

EXT Disk

With HyperDeck Extreme 8K HDR you can record directly to USB-C flash disks. These fast, high
capacity drives allow you to record video for long periods. You can then connect the flash disk
to your computer and edit directly from them!

For even higher storage capacities, you can connect a USB-C dock or external hard drive.

To connect your Blackmagic MultiDock 10G or USB-C flash disk, connect a cable from your
USB-C connected device to the ‘ext disk’ port on the rear of the HyperDeck Extreme 8K HDR.

Choosing an External Disk

The following External USB-C drives are recommended for recording 8K Apple ProRes LT up
to 60 fps.

Brand Card Name Storage

SanDisk SanDisk Extreme Portable SSD 1TB

Wise Wise Portable SSD PTS-512 512GB

Wise Wise Portable SSD PTS-1024 1TB

The following External USB-C drives are recommended for recording 8K H.265 High up
to 60 fps.

Brand Card Name Storage

Wise Wise Portable SSD PTS-256 256GB

TIP With the optional cache feature, you can even use slower CFast cards and

external disks as the cache will continue recording even if there are problems with
your media, no matter what resolution you are recording!

Preparing Media For Recording

Preparing Media on HyperDeck Extreme 8K HDR

CFast Cards can be formatted directly on the unit or via a Mac or Windows computer. Storage
media connected via the rear ‘ext disk’ USB-C port can be formatted on a Mac or
Windows computer.

HFS+, is also known as Mac OS X Extended, and is the recommended format as it supports
‘journaling’. Data on journaled media is more likely to be recovered in the rare event that your
storage media becomes corrupted. HFS+ is natively supported by macOS. exFAT is supported
natively by macOS and Windows without needing any additional software, but does not
supportjournaling.

41Storage Media

Preparing CFast Cards on HyperDeck Extreme 8K HDR

1 Tap the drive area icon on the front panel to enter the storage manager.

2 Tap ‘format card 1’ or ‘format card 2’ to select the card to format. These numbers

correspond to the labels on the CFast slots on the HyperDeck Extreme front
panel. The‘format card’ option will be grayed out if no media is inserted in the
corresponding slot.

3 If you want to rename the card, tap on the pencil icon to open the keyboard, type

the new name using the touchscreen keyboard and press ‘update’.

4 Choose ‘OS X Extended’ or ‘exFat’ and tap the format button.

42Storage Media

5 A confirmation window will appear detailing which card is to be formatted, the

selected format option and the card name. Tap on the ‘format card’ button.

6 Formatting will begin. While the card is being formatted the status led on the CFast slot

will illuminate green.

7 Once formatting is complete, tap ‘ok’.

Preparing Media on a Computer

Formatting Media on a Mac OS Computer

The Disk Utility application included with Mac OS can format a drive in the HFS+ or exFAT
formats. Make sure you back up anything important from your disk as you will lose everything
on it when it is formatted.

1 Connect an SSD to your computer with an external dock or cable adapter and dismiss

any message offering to use your SSD for Time Machine backups. For CFast cards,
connect it to your computer via an external card reader.

2 Go to applications/utilities and launch Disk Utility.

3 Click on the disk icon of your SSD or CFast card and then click the erase tab.

43Storage Media

4 Set the format to Mac OS Extended (Journaled) or exFAT.

5 Type a name for the new volume and then click erase. Your media will quickly be

formatted and made ready for use with HyperDeck.

Formatting Media on a Windows computer

The format dialog box can format a drive in the exFAT format on a Windows PC. Make sure you
back up anything important from your SSD or SD card as you will lose every thing on it when
it is formatted.

1 Connect an SSD to your computer with an external dock or cable adapter.

ForCFastcards, connect it to your computer via an external CFast card reader.

2 Open the start menu or start screen and choose computer. Right-click on your

SSD or CFast card.

3 From the contextual menu, choose format.

4 Set the file system to exFAT and the allocation unit size to 128 kilobytes.

5 Type a volume label, select quick format and click Start.

6 Your media will quickly be formatted and made ready for use with HyperDeck.

Use the Format dialog box feature
in Windows to format your SSD or
CFast card in the exFAT format

44Storage Media

Storage Indicators

The status of the storage media slots can be seen on the bottom toolbar of the main display.

These icons display the number, name, progress and status the CFast slots and active external
disk drive.

Number

Drives ‘1’ and ‘2’ show the two CFast card slots on the front panel. Drive ‘3’ shows the status of
the external drive connected via the ‘ext disk’ USB-C port on the rear.

TIP If you are using a drive hub you can connect multiple drives via the ‘ext disk’

connector on the rear. In this case the third drive icon will only display the active drive.

Name

The text to the right of the number is the name of the CFast card or ext disk. This will be the
name you selected when formatting the storage and is especially helpful if you are using the
Blackmagic MultiDock in order to make sure you are playing or recording to the correct drive!

Progress Bar

The bar icon will be either blue, white or red depending on its current status. The intensity of
the color will also display the used space on the card.

The blue drive icon indicates the active drive. If you press play, playback
willstart from this drive, if you want to record video, it will be to this drive.

A white drive icon indicates there is a CFast card or ext disk connec ted,
but not ac tive. A solid white icon indicates the drive is full.

The bar will be red during recording.

45Storage Media

Status

Text underneath the progress bar will display either the storage space remaining or the status
of the slot.

Capacity remaining

When your CFast card or drive has space remaining, the duration available will be
displayed in hours:minutes:seconds based on the current source format and your
chosen codec and quality settings. If there is less than an hour left, it will display
minutes:seconds remaining only.

If a valid source is not detected, the available storage remaining on the media will
display in gigabytes or terabytes.

Slot status

‘No card’ and ‘no drive’ will display if there is no media connected to that drive slot.

Once a CFast card or external disk is full, the icon will display ‘card full’ or ‘drive full’
soyou know it’s time to swap out the storage media. If you have another CFast card
inserted, the recording will automatically spill over and start recording onto it. If you
have an external disk connected, the recording will spill over when the second CFast
card is full.

A locked drive will be shown with ‘locked’ under the progress bar.

If you see ‘blocked’ display underneath the progress bar, this means you are unable to
play or record to that media. To resume playback or recording on that CFast card or
drive, eject it and reconnect. The CFast card or ext disk will now be available.

Active storage media

When using HyperDeck Extreme 8K HDR, you can connect up to 2 CFast cards and 5 ext
drives at once. This means you can access terabytes of recording space all from the one
HyperDeck Extreme disk recorder!

If you only have a single drive or CFast card connected, it is your active media for all playback
and recording.

If you are using more than one card or drive, you can select which one you want to use for
recording and playback.

To select your active media:

1 Tap on the drive icon area in the bottom screen.

2 In the storage media window, three large icons will appear. Tap on the drive you want

to make active. In playback mode the active drive will appear blue. In record mode the
active drive will be red.

46Storage Media

If you are using a dock to connect multiple external disks, such as the Blackmagic
MultiDock 10G, you can access the full list of attached drives by tapping on the ‘drive
list’ button.

To select an active drive from the drive list:

1 Tap on the ‘drive list’ button.

2 Select the drive from the list. The selected drive is indicated by the vertical blue line

to the left of the name. Press exit to return to the previous screen.

The blue line on the left hand side indicates which drive is selected.

NOTE Spill recording is available when multiple cards and drives are connected. Your

HyperDeck Extreme 8K will automatically spill recording from one CFast card to
another when it is full. Once the second CFast card is full, recording will spill over to
the active external disk.

47Storage Media

Using the Optional Internal Cache

The cache feature on HyperDeck Extreme 8K HDR enables you to record up to 8K Ultra HD on
to a M.2 NVMe PCIe flash disk in case of problems with your media.. This means you can use
slower external drives and CFast cards which in turn can be less expensive.

The cache works as short term storage, recording your video and audio to the internal M.2 PCIe
flash disk before transferring the files to your selected media in 5 second segments. These
5second segments then make up a single continuous file on your storage media.

Once you’ve installed an PCIe flash disk, all future recordings will be saved to the cache prior to
your storage media. Even if you turn your HyperDeck Extreme off, any files recorded prior that
weren’t transferred to a CFast card or external disk will still be there!

Choosing your M.2 NVMe PCIe Flash Disk

When choosing an M.2 NVMe PCIe flash disk for the cache, it is a good idea to keep in mind
future workflows and not just current ones. By selecting a flash disk that is capable of recording
the highest frame rates and resolutions, you can be sure you won’t miss a frame, even with the
slowest CFast cards or external disks.

The following M.2 PCIe flash disk are recommended for 8K Apple Pro Res HQ up to 60 fps.

Brand Card Name Storage

Samsung Samsung 960 EVO NVMe 1TB

Samsung Samsung 970 PRO V-NAND 1TB

Samsung Samsung 970 EVO Plus V-NAND 1TB

SanDisk SanDisk Extreme PRO 3D SSD 1TB

Installing The Cache

Installing a M.2 PCIe flash disk is easy and only needs to be done once. You can access the
cache location via a removable panel underneath the unit. There are four different length M.2
PCIe flash disks you can use; 2242, 2260, 2280 & 22110. The numbers relate to the width and
length of your NVMe, so a 2242 is 22 millimeters wide by 42 millimeters long.

If needed, the standof f and screw can be
relocated to the suitable slot on the board.

48Using the Optional Internal Cache

To install the cache:

1 Disconnect your HyperDeck Extreme 8K HDR from the power source. You can leave

other cables connected, but you may find it easier to remove them.

2 Turn the unit upside down and unfasten the 6 screws from the cover plate to remove it.

NOTE HyperDeck Extreme 8K HDR ships with thermally conductive heat pads

pre installed to fill the air gaps between your PCIe flash disk and the unit.
These work by transferring the heat away from the PCIe flash disk to the
chassis. One pad is installed onto the mother board, the other on the inside
of the cover plate. Remember to remove the blue protective film when
installing a SSD.

3 Unfasten the standoff mount screw. If you are using a different length NVMe card,

unscrew the standoff mount as well and lightly fasten it into the suitable slot.

4 Peel back the protective blue film on the motherboard heat pad.

5 Remove your NVMe SSD from the packaging and slide the card into place in the

PCIe slot. The slot will pivot up to 30 degrees to help installation.

49Using the Optional Internal Cache

6 Push the card down lightly onto the standoff mount and fasten the standoff screw.

You only need to tighten enough to keep the NVMe SSD snug.

7 Remove the protective blue film from the heat pad on the inside of the cover plate.

8 Replace the cover plate, the screws will only line up when installed correctly. You will

feel a little pressure on the cover plate from the density of the NVMe SSD combined
with the heat pads. This is normal as it is how they will conduct heat away from
the board.

9 Turn the unit right side up and reconnect your power and other cables.

Formatting The Cache

Once your NVMe SSD is installed you will need to format it.

1 When a recognized NVMe SSD is installed, the ‘cache’ icon will display ‘format’ instead

of ‘no cache’. Tap on the icon to open the format window.

2 A window will appear prompting you to format the cache. Tap on ‘format’. This will erase

any data on the NVMe SSD.

3 Formatting will begin. Once complete the cache will be ready to use. Tap ‘ok’.

Once your cache is formatted, you will not need to format it again unless you remove the NVMe
and install a different one, such as one with a higher capacity.

Cache Icons and Status

The storage capacity of the cache is dependent on the NVMe media size and the codec and
resolution you are recording. When you have a valid signal connected to the rear of the
HyperDeck Extreme 8K HDR, the cache icon on the front panel will display the duration
available to record based on your current resolution and selected codec. If there is no valid
signal connected, the cache icon will display the space available in GB.

50Using the Optional Internal Cache

There are four different status modes for the cache:

Standby The cache icon information will be white when the cache is in standbymode

Recording The cache icon will be red during recording and the duration indicator will reduce as

the space is filled. If you have fast storage media connected with usable space, the
duration indicator may not appear to move much as the storage media can copy f iles
as fast as your cache can record them. If you are using slower media or you have run
out of space, the available cache duration will decrease.

Stored If you run out of available on space on your connected storage media, the cache icon

will flash green and white until suff icient storage is connected and the information
stored on the cache is transferred over.

Transferring The cache icon will illuminate green while the cache media is being transferred to

CFast or USB-C external storage. Due to the nature of how the cache records, this
process can be very quick depending on your storage media.

If your media runs out of available storage space, the recording will continue to the
cache until the media is swapped.

Getting Started with HyperDeck Extreme Control

HyperDeck Extreme Control is a remote control panel that lets you control up to 8 HyperDeck
disk recorders or broadcast decks from a single control panel.

All playback and record units are controlled via the RS-422 connections on HyperDeck
Extreme Control’s rear panel.

If you have previously used broadcast decks with a search dial and edit controls, then
HyperDeck Extreme Control will feel very familiar to you. The controls follow a similar layout, so
you can operate the unit comfortably with confidence. The search dial even has a mechanical
clutch built in giving you a tactile response when using the shuttle or position modes.

This section of the manual will show you how to get started with your HyperDeck Extreme
Control, including plugging in power, connecting a HyperDeck Extreme 8K HDR, and making
sure the ‘remote’ button is enabled so you can control the unit remotely.

51Getting Started with HyperDeck Extreme Control

Plugging in Power

To power your HyperDeck Extreme Control, connect an IEC cable to the AC power input on the
rear of the unit. Youcan also use the 12V DC input if you want to connect external power or
redundancy via an external power supply, for example an uninterruptible power supply or
external 12V battery.

Connecting HyperDeck Extreme 8K HDR

HyperDeck Extreme Control features eight RS-422 connectors on the rear panel to allow
remote control of up to 8 HyperDeck units, or broadcast decks.

Connect the HyperDeck Extreme 8K HDR’s ‘remote in’ connector to your HyperDeck
controller’s RS-422 port labelled ‘1’ using an RS-422 serial cable.

By tightening the screws on both sides of the RS -422 connector, you
can prevent any interruption to the connection.

Enabling Remote Control on your HyperDeck

Now that your HyperDeck Extreme 8K HDR is connected, press the remote button labelled
‘rem’ on the unit’s front panel. This lets your HyperDeck disk recorder knowthat you are
assigning remote control to HyperDeck Extreme Control.

Playback using HyperDeck Extreme Control

The two rows of numbered soft buttons on the HyperDeck Extreme Control correspond to the
numbered RS-422 ports on the rear panel. Earlier in this section we connected HyperDeck
Extreme 8K HDR to RS-422 port 1. This means you can control that HyperDeck as either the
record or playback unit by selecting unit 1 on the playback and record buttons.

To enable the HyperDeck as a playback unit, simply press the ‘1’ button in the playback row.
The ‘1’ playback button will now be green.

52Getting Started with HyperDeck Extreme Control

If it’s not already illuminated, tap on the ‘player’ button. The timecode display and status
indicators on your HyperDeck controller will match the playback unit. Your HyperDeck
recorder is ready to be operated using HyperDeck Extreme Control’s powerful deck controls.

You can use the soft touch transport controls or the search dial and mode
buttons to control your HyperDeck Extreme 8K HDR.

Tap on the ‘shuttle’ button above the search dial. You can now turn the dial right and left to
shuttle through your video. Press the ‘stop’ button to exit shuttle mode. Now press ‘play’ for
real time playback, or the skip buttons to navigate from recorded clip to recorded clip.

The next section of the manual provides a basic workflow example showing how to control a
broadcast deck for archiving material to a HyperDeck Extreme 8K HDR.

HyperDeck Extreme Control Workflow

The following example features a traditional broadcast tape deck recording to a HyperDeck
Extreme 8K HDR recorder, but you don’t need to use a HyperDeck with the HyperDeck
Extreme Control. You could connect two or more traditional broadcast decks and dub from
tape to tape.

Connecting your RS-422 Devices

RS-422 connections on the rear of the HyperDeck Extreme Control allow up to 8 RS-422
enabled decks and devices to be attached from the rear or your HyperDeck recorder or
broadcast deck to the RS-422 connections on the rear panel of the HyperDeck Extreme
Control. Up to 8 separate devices can be connected.

1 Connect a 9 pin serial cable from the RS-422 connection on your tape based deck to

the firstRS-422 connection on the controller.

2 Now connect a serial cable from the RS-422 connection on your HyperDeck recorder

to the second RS-422 connection on the HyperDeck Extreme Control.

3 You can repeat these steps to connect up to 8 devices.

53HyperDeck Extreme Control Workflow

By tightening the screws to either side of your 9 pin serial
cable, you can prevent any interruption to the connection.

TIP HyperDeck Extreme 8K HDR and HyperDeck Extreme Control can both be rack

mounted using the HyperDeck rack mount kit. See the section ‘accessories’ later in
this manual.

Connecting your Video Signal

With the HyperDeck Extreme 8K HDR, you can use the large touchscreen display to view
playback ofyour tape device.

To connect your video signals:

1 Connect a BNC cable to the ‘SDI out’ connection on the rear of your tape based deck

to the ‘SDI in A’ connection on the HyperDeck Extreme 8K HDR.

2 Insert your cassette tape into the tape based deck.

3 Put your deck into ‘remote’ mode.

TIP The HyperDeck Extreme 8K HDR can accept both digital and analog based

sources, meaning you can also archive media from analog based tape decks. Just
connect the composite out of the tape deck to the composite in on the rear of the
HyperDeck Extreme 8K HDR.

54HyperDeck Extreme Control Workflow

Reference Signal

PLAYBACK

RECORD

HOURS MINUTES SECONDS FRAMES

SHUTTLE JOG POSITION

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

1

2

PLAYBACK

RECORD

TRIM PLAYER

REF

SERVO

REMOTE

RECORDER

HOURS MINUTES SECONDS FRAMES

IN

INPUT PREROLL SKIP REC SKIP

SHUTTLE JOG POSITION

EDIT EJECT REW PLAY F FWD STOP

OUT

ENTRY

DELETE

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8MM

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

1

2

The HyperDeck Extreme Control features reference in and reference out connections on the
rear panel to allow synchronous recordings.

If you are using an external reference source, connect your reference signal from the ‘ref out’
ofyourreference device or deck to the ‘ref in’ on the controller.

Selecting your Devices

Now that your RS-422 devices and video signals are attached, it’s time to select them on the
HyperDeck Extreme Control front panel. Choose you record and playback deck by selecting
the numbered soft button in the playback or record row.

1 On the front panel of the controller, press the button numbered ‘1’ on the top row.

Thisselects the tape deck you previously connected into the first RS-422 connection
as your playback deck. The button surround will illuminate green.

Press number ‘2’ button on the second row to select the HyperDeck Extreme 8K HDR
as your ‘record’ deck. The button surround will illuminate red to indicate this deck is
the recorder.

The green number 1 button indicated the playback deck,
the red button 2 indicates the recording deck.

Controlling your playback andrecord decks

Once your playback and record decks are connected and selected, you will be able to switch
control between the two by using the soft touch ‘player’ and ‘recorder’ buttons on the front
panel above the status indicators. When remote is enabled, you can then use the search dial
and transport controls to navigate to the location on your deck.

1 Press the soft touch ‘player’ button and the player button will illuminate. The timecode

display and deck status indicator LEDs on the controller will update to show the ref,
servo and remote status of the playback deck. If you press ‘recorder’, the displays will
update to show the status of the HyperDeck recorder.

When the ‘player’ button is selected, the timecode display will
update to match the deck selected as player. The deck status lights
will also update to ref lect the set tings of the connected device.

55HyperDeck Extreme Control Workflow

2 The deck status indicators to the left of the search dial display the conditions of the

active player or recorder.

Ref A valid reference signal is important to maintain synchronous timecode between

the connected decks. If the ‘ref’ status signal is unlit, your deck doesn’t have a
reference signal that matches your format. Connect a cable from the ref out of the
controller rear panel to the ref in on your deck.

Servo An illuminated ser vo light indicates that the tape deck is in playback or record

mode. Ifyour deck is idle, you may need to press a button on it to establish the
servo status.

Remote The remote LED lets you know whether the remote switch on the connec ted deck is

on or off. If the ‘remote’ indicator is not illuminated, this means your connec ted deck
is not in remote. While you can see the status of the deck and the timecode, you will
be unable to control the deck with the transport buttons or search dial. The location
of the remote button orswitch on traditional broadcast decks can vary. If you are
unable to locate the remote button or switch, refer to your deck’s manual.

TIP HyperDeck Studio models and HyperDeck Extreme 8K HDR have a

REM button on the front panel to turn on remote mode. If you are using a
HyperDeck Studio Mini, remote mode can be enabled via the control panel
display menu on the front panel.

Testing Control

Once your playback and record decks have the remote button enabled, you can then use the
search dial and transport controls to test control and navigate to the location on your deck.

1 To control the playback deck, press the ‘player’ button. The timecode display on the

controller will now update to reflect the timecode on your deck.

2 Turn the search dial to the right or left, or press the forward or rewind buttons.

The timecode will update to reflect the forward or reverse motion.

3 To control the record deck, press ‘recorder’. The timecode and status indicators will

now match those of your HyperDeck recorder. Turn the search dial to confirm control
or press one of the transport buttons.

Now that you have established control over your HyperDeck recorder and Digi Beta deck,
youcan use the search dial or transport buttons to locate your ‘in’ and ‘out’ points.

Finding your Timecode Point using the Search Dial

The HyperDeck Extreme Control search dial has three modes; shuttle, jog and position.
The selected button will illuminate when you choose your mode. The search direction
indicators will illuminate to show you which direction your are moving and at what speed.
Onceyou are spooled to your desired location, you can set your in and out points.

56HyperDeck Extreme Control Workflow

PLAYBACK

RECORD

TRIM PLAYER

REF

SERVO

REMOTE

RECORDER

HOURS MINUTES SECONDS FRAMES

IN

INPUT PREROLL SKIP REC SKIP

SHUTTLE JOG POSITION

EDIT EJECT REW PLAY F FWD STOP

OUT

ENTRY

DELETE

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

Shuttle

When you are in shuttle mode you can turn the dial to the left or right up to a maximum
of 120 degrees to rewind or fast forward your tape or file based media. The further you
turn the dial towards the 90 degree mark, the faster the media will spool until the clutch
engages to let you know you are at full speed. To stop spooling, return the dial to the
center position. You will feel a tap on the knob when you reach the center.

Full reverse Stop position

Forward Full speed for ward

Light indicators above the search
dialwill indicate the direc tion and
speed you are traveling inshuttle mode.

Jog

Jog mode offers precise control over tape and drive based decks with a slower speed
compared to ‘shuttle’ mode. Press the jog button to select jog mode and the button will
illuminate. The search dial will now respond to how fast you rotate the dial. The dial will
spin freely without any clutch engaging.

Light indicators will display the
direction of your search dial position.

Jog backward Jog forward

57HyperDeck Extreme Control Workflow

TIP You may find you use two or three search dial modes to find your

timecode point. Use ‘shuttle’ mode as a quick way to navigate to the area
ofinterest, then change to jog mode for more precision.

Position

Position mode lets your navigate to your area of interest based on the duration of the
tape or timeline you are viewing. On a traditional tape based broadcast deck, ‘position’
indicates whether you are near the start or end of a recorded tape. For a HyperDeck,
‘position’ indicates your location relevant to the timeline position.

The light indicators when in ‘position’ mode will indicate the position relative to the start
middle and end.

Near start of timeline Center of timeline

Towards end of timeline End of timeline

Position mode lights indicate your
position relative to the timeline

NOTE When using ‘position’ with a tape based deck, the position indicator will

improve with time as the deck is queried by the controller.

To locate your timecode point, make sure your ‘player’ has a reference signal and is in ‘remote’
mode. Then on the controller:

1 Press the ‘player’ button if it is not already illuminated

2 Press the ‘shuttle’ button. Once pressed, the button will illuminate.

3 Rewind your tape by turning the search dial knob to the left until you feel the clutch

engage. You are now rewinding at full speed and the tape will be spooling back to
the start.

4 Once you are nearing the timecode point, turn the dial back to the center. Once the

knob is near the center stop position you will feel a tap on the dial to let you know.

5 Press the ‘jog’ mode button. The jog button will now be illuminated. The dial will now

spin freely and you can turn it to f ind your desired timecode. The faster you turn the
dial, the faster the media will jog.

Now that you have found your timecode in point, you can use the four soft touch timecode
buttons to define your in and out timecode points. These timecode entry buttons operate the
same way as they do on traditional broadcast decks.

58HyperDeck Extreme Control Workflow

To set your timecode points:

PLAYBACK

RECORD

TRIM PLAYER

RECORDER

HOURS MINUTES SECONDS FRAMES

IN

SHUTTLE JOG POSITION

OUT

ENTRY

DELETE

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

ENTRY

1

2

PLAYBACK

RECORD

TRIM PLAYER

RECORDER

HOURS MINUTES SECONDS FRAMES

IN

SHUTTLE JOG POSITION

OUT

ENTRY

DELETE

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

1

2

PLAYBACK

RECORD

TRIM PLAYER

REF

SERVO

REMOTE

RECORDER

HOURS MINUTES SECONDS FRAMES

IN

INPUT PREROLL SKIP REC SKIP

SHUTTLE JOG POSITION

EDIT EJECT REW PLAY F FWD STOP

OUT

ENTRY

DELETE

M

M

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

1

2

1 Press ‘entry’ and ‘in’ to select your in point and release the buttons. The ‘in’ button

willbe illuminated to confirm an ‘in’ point is selected.

Press the entry and in buttons to set your in point

2 Now you can use the transport controls or search dial to locate your ‘out’ point. Once

you have found your out point, set it by pressing the ‘entry’ and ‘out’ buttons together.

Both the ‘in’ and ‘out’ buttons will now be illuminated.

The trim function lets you adjust your in and out points frame by frame. If you want to move
either of your timecode points by individual frames, you can do this by using the ‘trim’ buttons.

To trim your timecode frame by frame:

Press the ‘in’ button and then either trim ‘-’ or trim’+’ to move the in point backwards
orforwards one frame at a time.

Move your in point for ward by a frame by pressing
the ‘in’ button and the trim ‘+’ button

Once your ‘in’ point is set, you can repeat the above steps to locate the ‘out’ point using the
search dial.

Using the Transport Controls

You can also use the transport controls on the HyperDeck Extreme Control to navigate to your
in andout points. The two rows of transport controls feature buttons commonly found on
traditional broadcast decks and will be familiar to you. These buttons include ‘preroll’, ‘record’,
‘edit’, ‘eject’, ‘rewind’, ‘play’, ‘fast fwd’ and ‘stop’.

‘Skip’ reverse and ‘skip’ forwards buttons operate like previous and next buttons on file based
decks such as the HyperDeck Studio Mini, so you can quickly navigate from clip to clip.

Using REW, PLAY, F FWD and STOP buttons on the front panel let you
quickly control your video on file and tape based decks.

59HyperDeck Extreme Control Workflow

To locate your timecode point, make sure your ‘player’ has reference and is in remote, then on

PLAYBACK

RECORD

TRIM PLAYER

REF

SERVO

REMOTE

RECORDER

HOURS MINUTES SECONDS FRAMES

SHUTTLE JOG POSITION

M

M

the controller:

1 Press the ‘recorder’ button to control the deck you have previously selected as your

record deck.

2 Press the REW to F FWD buttons to rewind or fast forward.

3 Once you have reached your timecode, press STOP to stop playback and define select

your in point by pressing the ‘entry’ and ‘in’ buttons together.

The HyperDeck Extreme Control also features other transport controls for file based decks.

Skip forward and skip back

If you are using a file based deck for record or playback, such as the HyperDeck Extreme 8K
HDR, you can use the ‘skip’ forward and reverse buttons. Press ‘skip’ reverse once to skip back
to the first frame of the current clip. Press ‘skip’ forward and you will skip forward to the first
frame of the next clip.

The ‘skip’ buttons are either side of the ‘rec’ button. Pressing
‘skip’ reverse when already located on the first frame of a
clip will navigate you to the first frame of the previous clip.

Record

To start recording, press the ‘rec’ and ‘play’ buttons at the same time. During recordings you
can switch which storage media your HyperDeck Extreme 8K HDR is recording to by holding
down the record button for three seconds.

Input

Press the INPUT button to switch between playback or source mode on the recording deck.
When input is selected, the HyperDeck Extreme 8K HDR will display the connected source.

Preroll

When you press ‘preroll’, tape decks will rewind to the preroll point before the set in point. The
preroll duration can be set on broadcast decks and is often set to up to 5 seconds. For
example, if the preroll on a broadcast deck is set to 5 seconds and the preroll button is pressed
on the deck or HyperDeck Extreme Control, the deck will search and park the tape 5 seconds
prior to that point. This is important for tape based decks where the deck needs time to lock the
signal before it is useable.

Edit

Once you have set your in and/or out points on your playback and record units, pressing ‘edit’
will perform an auto edit, cueing your tapes to the preroll point and then starting the record.
The ‘edit’ button will flash when recording has started.

Eject

The ‘eject’ button has two different functions depending on whether you are connected to a
traditional tape based broadcast deck or a file based deck such as the HyperDeck
Extreme 8K HDR.

60HyperDeck Extreme Control Workflow

On a traditional
broadcast deck

Pressing the eject button will unthread a tape on the selected player or recorder and
eject the tape or cassette. Thetimecode panel will update to reflect the deck as it
will no longer reference the tape timecode.

On a HyperDeck
recorder

When a HyperDeck is in ‘stop’ mode, pressing the ‘eject’ button will switch your
active recording slot to the other one available. For example, HyperDeck recording
with slot 1 active will switch to slot 2. When you HyperDeck is in record or play mode,
pressing ‘eject’ will stop the record or playback and switch slots in the one step.

TIP If you are using a HyperDeck recorder with HyperDeck Extreme Control, the

illuminated ‘eject’ button will let you know there is no media inserted in the drive slots
of the HyperDeck recorder.

HyperDeck Extreme Control Front Panel

In this section of the manual you will find detailed descriptions of all the features on your
HyperDeck Extreme Control.

3

PLAYBACK

1 2 3 4 5 6 7 8

1

1 2 3 4 5 6 7 8

RECORD

6

ENTRY

OUT

IN

DELETE

INPUT PREROLL SKIP REC SKIP

7

EDIT EJECT REW PLAY F FWD STOP

TRIM PLAYER

RECORDER

REF

SERVO

REMOTE

5

HOURS MINUTES SECONDS FRAMES

M

M

SHUTTLE JOG POSITION

26

4

1 Playback and record buttons

16 numbered buttons let you select which deck is the player and which deck is the
recorder. The M buttons are not enabled at this time.

2 Player and Recorder buttons

Player and recorder buttons let you select your player or recorder device. Once you
press the player button, the status indicator and timecode will update to reflect the
deck or device selected as player.

3 Timecode Display

The timecode display will update to the connected deck when the numbered playback
or record button or ‘player’ or ‘recorder’ button is selected. When a drive or tape is
ejected, the timecode display will revert to the deck default, generally 00:00:00:00.

61HyperDeck Extreme Control Front Panel

4 Search dial, indicator LEDs and mode buttons

There are three modes when using the large search dial; shuttle, jog and position.
Therow of LED lights will indicate the search direction depending on which mode
isselected. Turn the dial left or right to fast forward or rewind.

5 Transport Controls

Traditional transport controls provide familiar playback controls including play, stop,
record and edit. The skip buttons are for file based decks such as a
HyperDeck recorder.

6 Timecode Entry and Trim buttons

You can select your in and out points and refine them frame by frame by using the
timecode entry and trim buttons.

7 Deck status indicators

LED indicators will display the status of the deck letting you know when it is ready for
playback and recording.

HyperDeck Extreme Control Rear Panel

8

8 Power Inputs

The HyperDeck Extreme Control has inputs for both AC and DC power.

9 USB

A USB port lets you connect your controller to a computer so you can update via the
HyperDeck Setup Utility.

10 Ethernet

The ethernet connection is not enabled at this time.

11 Reference

Reference out and reference in connections for synchronous recordings between
connected devices.

12 Deck Control

Eight numbered RS-422 connections to connect up to 8 RS-422 enabled devices.

9

1110

12

62HyperDeck Extreme Control Rear Panel

Accessories

Rack Mounting HyperDeck

The HyperDeck Extreme 8K HDR and HyperDeck Extreme Control can be rack mounted into a
broadcast rack or road case using the HyperDeck rack mount kit.

Sitting at three rack units high and half the width of a standard rack, HyperDeck Extreme can
be mounted side by side or individually using the blanking panel provided with the kit.

The HyperDeck rack mount kit includes the following:

The HyperDeck Extreme Rack Kit contains the following items:

2 x Rack ears

Attach rack ‘ears’ to the outside edge of
HyperDeck Extreme for mounting in a rack.

1 x Half rack width blanking panel

The blanking panel has a mounting ear on one side
so you can cover the empty rack space if you are
installing a single unit. The illustration shows the ear
on the right side. Simply rotate thepanel 180° to
mount it to the other side.

2 x Support brackets

The T-shaped support brackets attach underneath
the HyperDeck Extreme units where thetwo units
meet at the front and the rear toprovide support.

Screws

8 x M4 10mm

Rack
ear screws

2 x Cable tab insert

4 x M4 8mm

Blanking
panel screws

15 x M3 5mm

Support bracket
screws

63Accessories

Preparing the HyperDeck Extreme 8K HDR or
HyperDeck Extreme Control for individual rack installation:

1 Position the blanking panel on one of the sides of your HyperDeck unit, depending on

whether you would like the unit to sit on the right or left of the shelf. The front face of
the blanking panel should be parallel with the front panel of the unit.

2 Attach the blanking panel to the side of your HyperDeck unit using three of the

supplied blanking panel screws.

3 Use three of the rack ear screws to attach a rack ear to the other side of the

HyperDeck unit.

With the rack ear and blanking panel now attached, you can install the HyperDeck unit into a
rack. Use the mounting holes on both sides and standard rack screws.

Preparing to rack mount a HyperDeck Extreme 8K HDR
with a HyperDeck Extreme Control.

When rack mounting HyperDeck Extreme 8K HDR and HyperDeck Extreme Control side by
side, it’s best to have the controller on the right. This way your headphone port will be on the
far left and your search dial on the far right, making it a seamless transition from traditional
broadcast deck to your HyperDeck Extreme.

1 The two units will be joined on one side using support brackets, so the first step is to

remove the two rubber feet from the joining side of each unit.

2 The units will be secured via the cable brackets on the rear along with t shaped

support brackets installed on the base.

64Accessories

On the rear cable brackets, insert a cable tab insert into the top and bottom holes on
one unit, securing each in place using the supplied support bracket screws. Attach the
two t-shaped supports between the two units at the front and rear and screw in place
using support brackets screws.

3 The cable tab insert installed previously should line up with the holes of the cable

bracket on the other unit. Secure with the supplied support bracket screws. You can
now turn the unit right side up.

4 Attach the rack ears to the outer edges near the front of both units using the supplied

rack ear screws. Your HyperDeck Extreme 8K HDR and HyperDeck Extreme Control
are now ready to be mounted into your rack as a single unit.

RS-422 Control

What is RS-422 Control?

The RS-422 standard is a serial deck control broadcast standard and has been used by
broadcasters since the early 1980s and is found on many decks, linear editors, non linear
editors and broadcast automation products. All current HyperDeck models support this
standard so can be integrated into broadcast automation, remote control systems, editing
systems and any kind of custom control you might like to design yourself.

HyperDeck Extreme 8K HDR also supports file based commands from the Advanced Media
Protocol via RS-422. This lets you control your HyperDeck with an external device using AMP
commands such as adding clips to a playlist, determining the filename of the next clip, looping a
single clip or timeline, or clearing a playlist.

Using an External RS-422 Controller

All current HyperDeck models feature an industry standard Sony™ compatible RS-422 deck
control port, which has the correct pin connections for a direct connection to any remote
controller that supports RS-422.

You can use pre-manufactured 9 pin cables as long as each end of the cable is wired ‘pin for
pin’ where the same pin numbers on each end of the cable are connected together. If you
would like to make custom cables, please refer to the accompanying wiring diagram.

Using RS-422 control means you can build your own custom controller, or incorporate your
HyperDeck Extreme 8K HDR into an already existing RS-422 control solution.

65RS-422 Control

For example, you can remotely start and stop recording and playback of your HyperDeck as
well as performing other common jog and shuttle functions. The full list of supported RS-422
commands is in the following section named ‘supported RS- 422 commands’.

5 4 3 2 1

Receive

(–)

2 7 8 3 1, 4, 6, 9

9 8 7 6

RS-422 remote pin connections

Remote port on HyperDeck Extreme 8K HDR

Receive

(+)

Transmit

(–)

Transmit

(+)

Ground

Pins

Supported RS-422 Commands

Command Reply No Remote Notes

0 - System Control

0x00 0x11 DeviceTypeRequest

1 - Slave Response

0x20 0x00 Stop Acknowledge Disabled

0x20 0x01 Play Acknowledge Disabled

0x20 0x02 Record Acknowledge Disabled

0x20 0x04 StandbyOff Acknowledge Disabled

0x20 0x05 StandbyOn Acknowledge Disabled

0x20 0x0F Eject Acknowledge Disabled

0x20 0x10 FastFwd Acknowledge Disabled

0x21 0x11 JogFwd1 Acknowledge Disabled

0x22 0x11 JogFwd2 Acknowledge Disabled

NTSC: 0xF0E0
PAL: 0xF1E0
24P: 0xF2E0

Enabled

Treated as N=1;
Same as JogFwd1

66RS-422 Control

Command Reply No Remote Notes

0x21 0x12 VarFwd1 Acknowledge Disabled Uses ShuttleFwd1

0x22 0x12 VarFwd2 Acknowledge Disabled

0x21 0x13 ShuttleFwd1 Acknowledge Disabled

0x22 0x13 ShuttleFwd2 Acknowledge Disabled

0x20 0x20 Rewind Acknowledge Disabled

0x21 0x21 JogRev1 Acknowledge Disabled

0x22 0x21 JogRev2 Acknowledge Disabled

0x21 0x22 VarRev1 Acknowledge Disabled Uses ShuttleRev1

0x22 0x22 VarRev2 Acknowledge Disabled

0x21 0x23 ShuttleRev1 Acknowledge Disabled

0x22 0x23 ShuttleRev2 Acknowledge Disabled

0x20 0x30 Preroll Acknowledge Disabled

0x24 0x31 CueData Acknowledge Disabled

0x20 0x34 SyncPlay Acknowledge Disabled

0x21 0x38 ProgSpeedPlayPlus Acknowledge Disabled

0x21 0x39 ProgSpeedPlayMinus Acknowledge Disabled

Treated as N=1;
Same as VarFwd1

Treated as N=1;
Same as ShuttleFwd1

Treated as N=1;
Same as JogRev1

Treated as N=1;
Same as VarRev1

Treated as N=1;
Same as ShuttleRev1

0x20 0x40 Preview Acknowledge Disabled Status bits are set

0x20 0x41 Review Acknowledge Disabled Status bits are set

0x20 0x43 OutpointPreview Acknowledge Disabled

0x22 0x5C DMCSetFwd Acknowledge Disabled

0x22 0x5D DMCSetRev Acknowledge Disabled

0x20 0x60 FullEEOff Acknowledge Disabled

0x20 0x61 FullEEOn Acknowledge Disabled

0x20 0x63 SelectEEOn Acknowledge Disabled

4 - Preset/Select Control

0x40 0x10 InEntry Acknowledge Disabled

0x22 0x23 ShuttleRev2 Acknowledge Disabled

0x20 0x30 Preroll Acknowledge Disabled

0x24 0x31 CueData Acknowledge Disabled

0x20 0x34 SyncPlay Acknowledge Disabled

0x21 0x38 ProgSpeedPlayPlus Acknowledge Disabled

0x21 0x39 ProgSpeedPlayMinus Acknowledge Disabled

0x40 0x11 OutEntry Acknowledge Disabled

Treated as N=1;
Same as ShuttleRev1

0x44 0x14 InDataPreset Acknowledge Disabled

67RS-422 Control

Command Reply No Remote Notes

0x44 0x15 OutDataPreset Acknowledge Disabled

0x40 0x18 InShift+ Acknowledge Disabled

0x40 0x19 InShift- Acknowledge Disabled

0x40 0x1A OutShift+ Acknowledge Disabled

0x40 0x1B OutShift- Acknowledge Disabled

0x40 0x20 InReset Acknowledge Disabled

0x40 0x21 OutReset Acknowledge Disabled

0x40 0x22 AInReset Acknowledge Disabled

0x40 0x23 AOutReset Acknowledge Disabled

0x44 0x31 PrerollPreset Acknowledge Disabled

0x40 0x40 AutoModeOff Acknowledge Disabled

0x40 0x41 AutoModeOn Acknowledge Disabled

0x41 0x37 InputCheck Acknowledge Disabled

6 - Sense Request

0x61 0x0A TimeCodeGenSense — —

0x61 0x0C CurrentTimeSense — —

0x60 0x10 InDataSense InData Enabled

0x60 0x11 OutDataSense OutData Enabled

0x60 0x12 AInDataSense AInData Enabled

0x60 0x13 AOutDataSense AOutData Enabled

0x61 0x20 StatusSense StatusData Enabled

0x60 0x2B RemainTimeSense RemainTimeData Enabled

0x60 0x2E SpeedSense SpeedData Enabled

0x60 0x31 PrerollTimeSense PreRollTimeData Enabled

0x60 0x36 TimerModeSense TimerModeData Enabled

0x60 0x3E RecordInhibitSense RecordInhibitStatus Enabled

ignored, Status bit
remembered

ignored, Status bit
remembered

7 - Sense Reply

0x78 0x00 Timer1Data — —

0x78 0x04 LTCUserBitsTimeData — —

0x78 0x06 VITCUserBitsTimeData — —

0x74 0x06 VITCTimeData — — Current Time

0x74 0x07 UserBitsVITCTimeData — — 00:00:00:00

0x74 0x08 GenTCData — — Current Time

0x78 0x08 GenTCUBData — —

Current Time and
00:00:00:00

Current Time and
00:00:00:00

Current Time and
00:00:00:00

Current Time and
00:00:00:00

68RS-422 Control

Command Reply No Remote Notes

0x74 0x09 GenUBData — — 00:00:00:00

0x74 0x10 InData — —

0x74 0x11 OutData — —

0x74 0x12 AInData — —

0x74 0x13 AOutData — —

0x74 0x14 CorrectedLTCTimeData — — Current Time

Please see “Status Bit s”

0x70 0x20 StatusData — —

0x76 0x2B RemainTimeData — —

0x71 0x2E SpeedData — —

0x74 0x31 PrerollTimeData — —

0x71 0x36 TimerModeData — — Returns 0 (TimeCode)

0x72 0x3E RecordInhibitStatus — —

sheet: Limited to 9 bytes
of status, silently
truncated

A - Advanced Media Protocol

0xA1 0x01 AutoSkip Acknowledge Disabled

0xAX 0x15 ListNextID IDListing Enabled

0x20 0x29 ClearPlaylist Acknowledge Disabled

0x41 0x42 SetPlaybackLoop Acknowledge Disabled

0x41 0x44 SetStopMode Acknowledge Disabled

0x4f 0x16 AppendPreset Acknowledge Disabled

Blackmagic Extensions

0x08 0x02 BmdSeekToTimelinePosition Acknowledge Disabled

0x03 0x08 BMDSeekRelativeClip Acknowledge Disabled

8-bit signed number of
clips to skip from current
clip

when x = 0 single clip
request when x = 1, #
clips can be specified in
the send data

Bit 0 loop mode enable,
0=false 1=true

Bit 1 is single clip/timeline
0=single clip
1=timeline

0 = Off
1 = Freeze on last frame
2 = Freeze on nex t clip
3 = Show black

16-bit little endian
fractional position
[0..65535]

One-byte signed integer,
which is the number of
clips to skip (negative for
backwards).

69RS-422 Control

RS-422 Developer Information

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

Byte 0

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Byte 8

Byte 9

Variables

Cassette Out

Local

Standby

Direction

0 0 Cassette out 0 0 0 0 Local

Standby 0 Stop 0 Rewind Forward Record Play

Servo Lock 0 Shuttle Jog Var Direction Still 1

Auto Mode 0 0 0 Aout Set Ain Set Out Set In Set

Select EE Full EE 0 0 0 0 0 0

0 0 0 0 0 0 0 0

0 Lamp Still Lamp Fwd Lamp Rev 0 0 0 0

0 0 0 0 0 0 0 0

0 0 Near EOT EOT 0 0 0 0

0 0 0 0 0 0 0 0

Set if no SSD is present

Set if Remote is disabled (local control)

Set if a disk is available

Clear if playback is forwarding, set if playback is reversing

Still

Auto Mode

Select EE, Full EE

Lamp Still/Fwd/Rev

Near EOT

EOT

Others

Cue Complete (byte 2, bit 0)

HyperDeck Serial RS-422 Protocol

Protocol

Interface

Set if playback is paused, or if in input preview mode

Set if in Auto Mode

Set if in input preview mode

Set according to playback speed and direction

Set if total space left on available SSDs is less than 3 minutes

Set if total space left on available SSDs is less than 30 seconds

Always 1: Cue requests are always instantaneous

Based on Sony 9-pin protocol

Baud rate 38.4 Kbps

1 star t bit

8 data bits

1 stop bit

1 parity bit

Odd parity

70RS-422 Control

Transferring Files over a Network

HyperDeck Extreme 8K HDR supports file transfer via file transfer protocol, or ftp. This powerful
feature lets you copy files directly from your computer to your HyperDeck via a network with
the fast speeds a local network can provide. For example, you could be copying new files to a
HyperDeck unit being used for playing back video on monitor walls and digital signage.

Connecting to HyperDeck Extreme 8K HDR

With your computer and HyperDeck Extreme 8K HDR on the same network, all you need is an
ftpclient and your HyperDeck Extreme 8K HDR’s IP address.

1 Download and install an FTP client on the computer you want to connect your

HyperDeck Extreme to. Werecommend Cyberduck, FileZilla or Transmit but most
FTPapplications will work. Cyberduck and FileZilla are free downloads.

2 Connect your HyperDeck Extreme 8K HDR to your network using an Ethernet cable

and noteits IP address.

If you haven’t previously connected the HyperDeck Extreme 8K HDR to the network,
see ‘setup’ menu settings to find out how to connect it to the network.

3 Enter your HyperDeck Extreme 8K HDR’s IP address into your FTP client’s connection

dialog. The naming and position of this box can vary between applications, but it is
usually labeled ‘server’ or ‘host.’ If your FTP program includes an ‘anonymous login’
checkbox, make sure this is checked.

When connecting to HyperDeck Extreme 8K HDR, you don’t need to enter a username
or password. Simply enter your disk recorder’s IP address in your FTP application’s
‘server’ or ‘host’ field and check an ‘anonymous login’ checkbox if one is available.

71Transferring Files over a Network

Transferring Files

Once connected to HyperDeck Extreme 8K HDR you can transfer files as you normally would
with your ftp program. Most ftp applications have a drag and drop interface, but check your
particular application for the appropriate method.

You can also transfer any file to and from a HyperDeck Extreme 8K HDR, but it’s worth noting
that any files you intend to play back from the HyperDeck will need to conform to your
HyperDeck’s supported codecs and resolutions. You can find a list of supported codecs in the
‘Blackmagic HyperDeck Setup’ section of this manual.

TIP You can transfer files over a network while your HyperDeck Extreme 8K HDR is

recording. HyperDeck Extreme 8K HDR will automatically adjust transfer speeds to
make sure recording is not affected.

Developer Information

Blackmagic HyperDeck Ethernet Protocol

Ver sio n 1.10

The Blackmagic HyperDeck Ethernet Protocol is a text based protocol accessed by connecting
to TCP port 9993 on HyperDeck Extreme 8K HDR. If you are a software developer you can use
the protocol to construct devices that integrate with our products. Here at Blackmagic Design
our approach is to open up our protocols and we eagerly look forward to seeing what you
come up with!

You can connect to your HyperDeck recorder using the HyperDeck Ethernet Protocol using a
command line program on your computer, such as Terminal on a Mac and putty on a
Windows computer.

The HyperDeck Ethernet Protocol lets you schedule playlists and recordings. The following is
an example of how to For example, to play 7 clips from clip number 5 onwards via the
HyperDeck Ethernet Protocol. If your recorder is installed out of reach, you can also turn on the
‘remote’ feature via ethernet.

On a Mac

1 Open the Terminal application which is located with the applications > utilities folder.

2 Type in “nc” and a space followed by the IP address of your HyperDeck Extreme 8K

HDR another space and “9993” which is the HyperDeck Ethernet Protocol port number.
For example type: nc 192.168.1.154 9993. The Protocol preamble will appear.

3 Type “playrange set: clip id: 5 count: 7” and press ‘return’.

If you look on the timeline on the front panel of the HyperDeck Extreme 8K HDR, you
will see in and out points marked around clips 5 through the end of clip 11.

4 Type “play”. Clips 5 through 11 will now play back.

5 To clear the playrange, type “playrange clear”

6 To exit from the protocol, type ‘quit’.

72Developer Information

Protocol Commands

Command Command Description

help Provides help text on all commands and parameters

commands return commands in XML format

device info return device information

disk list query clip list on active disk

disk list: slot id: {n} query clip list on disk in slot {n}

quit disconnect ethernet control

ping check device is responding

preview: enable: {true/false} switch to preview or output

play play from current timecode

play: speed: {-5000 to 5000} play at specific speed

play: loop: {true/false} play in loops or stop-at-end

play: single clip: {true/false} play current clip or all clips

playrange query play range setting

playrange set: clip id: {n} set play range to play clip {n} only

playrange set: clip id: {n} count: {m} set play range to {m} clips starting from clip {n}

playrange set: in: {inT} out: {outT}

playrange set: timeline in:

{in} timeline out: {out}

playrange clear clear/reset play range setting

play on startup query unit play on startup state

play on startup: enable: {true/false} enable or disable play on startup

play on startup: single clip: {true/false} play single clip or all clips on startup

play option query play option

play option: stop mode:
{lastframe/nextclip/black}

record record from current input

record: name: {name} record named clip

record spill spill current recording to nex t slot

record spill: slot id: {n}

stop stop playback or recording

set play range to play between:

- timecode {inT} andtimecode {outT}

set play range in units of frames between:

- timeline position {in} and position {out}

set output frame when playback stops

spill current recording to specified slot use current slot id to spill
to same slot

clips count query number of clips on timeline

clips get query all timeline clips

clips get: clip id: {n} query a timeline clip info

clips get: clip id: {n} count: {m} query m clips starting from n

73Developer Information

Command Command Description

query clip info using specified output version:

clips get: version: {1/2}

clips add: name: {name} append a clip to timeline

clips add: clip id: {n} name: {name} insert clip before existing clip {n}

version 1: id: name startT duration
version 2: id: startT duration inT outT name

clips add: in: {inT} out: {outT} name:

{name}

clips remove: clip id: {n} remove clip {n} from the timeline

clips clear empty timeline clip list

transport info query current activity

slot info query active slot

slot info: slot id: {n} query slot {n}

slot select: slot id: {n} switch to specif ied slot

slot select: video format: {format} load clips of specified format

cache info query cache status

dynamic range query dynamic range

dynamic range: playback override:

{auto/Rec709/Rec2020_SDR/HLG/
ST2084_300/ST2084_500/
ST2084_ 800/ST2084_1000/
ST2084_2000/ST2084_4000/ST2048}

notify query notification status

notify: remote: {true/false} set remote notifications

append the {inT} to {outT} portion of clip

set playback dynamic range override

notify: transport: {true/false} set transport notifications

notify: slot: {true/false} set slot notifications

notify: configuration: {true/false} set configuration notifications

notify: dropped frames: {true/false} set dropped frames notifications

notify: display timecode: {true/false} set display timecode notifications

notify: timeline position: {true/false} set playback timeline position notifications

notify: playrange: {true/false} set playrange notifications

notify: cache: {true/false} set cache notifications

notify: dynamic range: {true/false} set dynamic range notif ications for input or playback video

goto: clip id: {n} goto clip id {n}

goto: clip id: +{n} go forward {n} clips

goto: clip id: -{n} go backward {n} clips

goto: clip: {start/end} goto start or end of clip

goto: clip: {n} go forward {n} frames within current clip

goto: clip: +{n} go forward {n} frames within current clip

goto: clip: - {n} go backward {n} clips

goto: timeline: {start/end} goto start or end of timeline

74Developer Information

Command Command Description

goto: timeline: {n} goto frame position {n} within timeline

goto: timeline: +{n} go forward {n} frames within timeline

goto: timeline: -{n} go backward {n} frames within timeline

goto: timecode: {timecode} goto specified timecode

goto: timecode: +{timecode} go forward {timecode} duration

goto: timecode: -{timecode} go backward {timecode} duration

goto: slot id: {n} goto slot id {n} equivalent to “slot select: slot id: {n}”

jog: timecode: {timecode} jog to timecode

jog: timecode: +{timecode} jog forward {timecode} duration

jog: timecode: -{timecode} jog backward {timecode} duration

shuttle: speed: {-5000 to 5000} shuttle with speed

remote query unit remote control state

remote: enable: {true/false} enable or disable remote control

remote: override: {true/false} session override remote control

configuration query configuration settings

configuration: video input: optical switch to optical input

configuration: video input:

{SDI/HDMI/component/composite}

configuration: audio input:

{embedded/XLR/RCA}

configuration: file format: {format} switch to specific file format

configuration: timecode input:

{external/embedded/preset/clip}

configuration: timecode preset:
{timecode}

configuration: audio input channels: {n} set the number of audio channels recorded to {n}

configuration: record trigger:

{none/recordbit/timecoderun}

configuration: record prefix: {name} set the record prefix name (supports UTF-8 name)

configuration: append timestamp:

{true/false}

uptime return time since last boot

format: slot id: {n} prepare:

{exFAT/HFS+} name: {name}

change the video input

change the audio input

change the timecode input

set the timecode preset

change the record trigger

append timestamp to recorded filename

prepare formatting operation filesystem type with
volumename{name}

“slot id” can be omitted for the current mounted slot

“name” defaults to current volume name if mounted (supports
UTF-8)

format: confirm: {token} perform a pre-prepared formatting operation using token

identify: enable: {true/false} identify the device

watchdog: period: {period in seconds} client connection timeout

75Developer Information

Command Combinations

You can combine the parameters into a single command, for example:

play: speed: 200 loop: true single clip: true

Or for configuration:

configuration: video input: SDI audio input: XLR

Or to switch to the second disk, but only play NTSC clips:

slot select: slot id: 2 video format: NTSC

Using XML

While you can use the Terminal to talk to HyperDeck, if you are writing software you can use
XML to confirm the existence of a specific command based on the firmware of the HyperDeck
you are communicating with. This helps your software user interface adjust to the capabilities of
the specific HyperDeck model and software version.

Protocol Details

Connection

The HyperDeck Ethernet server listens on TCP por t 9993.

Basic syntax

The HyperDeck protocol is a line oriented text protocol. Lines from the server will be separated by an ascii
CR LF sequence. Messages from the client may be separated by LF or CR LF.

New lines are represented in this document as a "↵" symbol.

Command syntax

Command parameters are usually optional. A command with no parameters is terminated with a new line:

{Command na me}↵

If parameters are specified, the command name is followed by a colon, then pairs of parameter names and
values. Each parameter name is terminated with a colon character:

{Command na me}: {Parameter}: {Value} {Parameter}: {Value} ...↵

Response syntax

Simple responses from the server consist of a three digit response code and descriptive text terminated by
a new line:

{Response code} {Response text}↵

If a response carries parameters, the response text is terminated with a colon, and parameter name and
value pairs follow on subsequent lines until a blank line is returned:

{Response code} {Response text}:↵

{P a r a m e t e r}: {V a l u e}↵

{P a r a m e t e r}: {V a l u e}↵

...

↵

Successful response codes

A simple acknowledgement of a command is indicated with a response code of 200:

200 ok↵

Other successful responses carry parameters and are indicated with response codes in the range
of 201 to 299.

76Developer Information

Failure response codes

Failure responses to commands are indicated with response codes in the range of 100 to 199:

100 syntax error

101 unsupported parameter

102 invalid value

103 unsupported

104 disk full

105 no disk

106 disk error

107 timeline empty

108 internal error

109 out of range

110 no input

111 remote control disa bled

120 connection rejected

150 invalid state

151 invalid codec

160 invalid format

161 invalid token

162 format not prepared

Asynchronous response codes

The server may return asynchronous messages at any time. These responses are indicated with response
codes in the range of 500 to 599:

5xx {Response Text}:↵

{P a r a m e t e r }: {V a lu e}↵

{P a r a m e t e r }: {V a lu e}↵

↵

Connection response

On connection, an asynchronous message will be delivered:

500 connection info:↵

protocol version: {Version}↵

model: {Model Name}↵

↵

Connection rejection

Only one client may connect to the server at a time. If other clients attempt to connect concurrently,
they will receive an error and be disconnected:

120 connection rejected↵

Timecode syntax

Timecodes are expressed as non-drop-frame timecode in the format:

H H:M M:SS:F F

77Developer Information

Handling of deck "remote" state

The “remote” command may be used to enable or disable the remote control of the deck. Any attempt to
change the deck state over ethernet while remote access is disabled will generate an error:

111 remote control disa bled↵

To enable or disable remote control:

remote: enable: {“true”, “false”} ↵

The current remote control state may be overridden allowing remote access over ethernet irrespective of
the current remote control state:

remote: override: {“true”, “false”} ↵

The override state is only valid for the currently connected ethernet client and only while the connection
remains open.

The “remote” command may be used to query the remote control state of the deck by specifying no
parameters:

remote↵

The deck will return the current remote control state:

210 remote info:↵

ena bled: {“tru e”, “false”}↵

overrid e: {“tr ue”, “false”}↵

↵

Asynchronous remote control information change notification is disabled by default and may be configured
with the “notif y” command. When enabled, changes in remote state will generate a “510 remote
info:”asynchronous message with the same parameters as the “210 remote info:” message.

Closing connection

The "quit" command instructs the ser ver to cleanly shut down the connec tion:

q uit↵

Checking connection status

The "ping" command has no function other than to determine if the server is responding:

ping↵

Getting help

The "help" or "?" commands return human readable help text describing all available commands and
parameters:

help↵

Or:

?↵

The server will respond with a list of all supported commands:

201 hel p:↵

{He lp T e x t}↵

{He lp T e x t}↵

↵

Switching to preview mode

The "preview" command instructs the deck to switch between preview mode and output mode:

preview: enable: {"true", "false"}↵

Playback will be stopped when the deck is switched to preview mode. Capturing will be stopped when the
deck is switched to output mode.

78Developer Information

Controlling device playback

The “play” command instructs the deck to start playing:

play↵

The play command accepts a number of parameters which may be used together in most combinations.

By default, the deck will play all remaining clips on the timeline then stop.
The “single clip” parameter may be used to override this behaviour:

play: single clip: {“true”, “false”}↵

By default, the deck will play at normal (100%) speed. An alternate speed may be specif ied in percentage
between -5000 and 5000:

play: speed: {% normal speed}↵

By default, the deck will stop playing when it reaches to the end of the timeline. The “loop” parameter may
be used to override this behaviour:

play: loop: {“true”, “false”}↵

The “playrange” command returns the current playrange setting if any:

playrange↵

To override this behaviour and select a particular clip:

playrange set: clip id: {Clip ID}↵

To only play a certain number of clips starting at a particular clip:

playrange set: clip id: {n} count: {m}↵

To only play a certain timecode range:

playrange set: in: {in timecode} out: {out timecode}↵

To play a certain timeline range:

playrange set: timeline in: {in} timeline out: {out}↵

To clear a set playrange and return to the default value:

playrange clear↵

The “play on startup command” instructs the deck on what action to take on startup. By default, the deck
will not play. Use the “enable” command to start playback af ter each power up.

play on startup: enable {“true”, “false”}↵

By default, the unit will play back all clips on star tup. Use the “single clip” command to override:

play on startup: single clip: {“true”, “false”}↵

The “play option” command queries the output frame for when playback stops:

play option↵

By default, the deck will display the last frame when playback stops. To override this behaviour, the “stop
mode” parameter can be used:

play option: stop mode: {“lastframe”, “nextfra me”, “black”}↵

Stopping deck operation

The "stop" command instructs the deck to stop the current playback or capture:

stop↵

Changing timeline position

The “goto” command instructs the deck to switch to playback mode and change its position within the
timeline.

To go to the start of a specific clip:

goto: clip id: {Clip ID}↵

To move forward/back {count} clips from the current clip on the current timeline:

goto: clip id: +/-{count}↵

Note that if the resultant clip id goes beyond the first or last clip on timeline, it will be clamp at the first or
last clip.

79Developer Information

To go to the start or end of the current clip:

goto: clip: {“start”, “end”}↵

To go to the start of the f irst clip or the end of the last clip:

goto: timeline: {“start”, “end”}↵

To go to a specified timecode:

goto: timecode: {timecode}↵

To move forward or back a specified duration in timecode:

goto: timecode: {“+”, “-”}{duration in tim ecode}↵

To specify between slot 1 and slot 2:

goto: slot id: {Slot ID}↵

Note that only one parameter/value pair is allowed for each goto command.

Enumerating supported commands and parameters

The "commands" command returns the supported commands:

commands↵

The command list is returned in a computer readable XML format:

212 c o mm a n ds:

<commands>↵

<command name="…"><parameter name="…"/>…</com mand>↵

<command name="…"><parameter name="…"/>…</com mand>↵

…

</c o m m a nd s>↵

↵

More XML tokens and parameters may be added in later releases.

Controlling asynchronous notifications

The "notify" command may be used to enable or disable asynchronous notifications from the server.
To enable or disable transport notifications:

notify: transport: {"true", "false"}↵

To enable or disable slot notifications:

notify: slot: {"true", "false"}↵

To enable or disable remote notifications:

notify: remote: {"true", "false"}↵

To enable or disable configuration notifications:

notify: configuration: {“true”, “false”}↵

Multiple parameters may be specified. If no parameters are specified, the server returns the current state of
all notifications:

209 n otif y:↵

transpor t: {“tr ue”, “fa lse”}↵

slot: {“true”, “false”}↵

re mote: {“true”, “false”}↵

configuration: {“true”, “false”}↵

↵

80Developer Information

Retrieving device information

The "device info" command returns information about the connected deck device:

device info↵

The server will respond with:

204 device info:↵

protocol version: {Version}↵

model: {Model Name}↵

unique id: {unique alphanumeric identifier}↵

↵

Retrieving slot information

The “slot info” command returns information about a slot. Without parameters, the command returns
information for the currently selected slot:

slot info↵

If a slot id is specified, that slot will be queried:

slot info: slot id: {Slot ID}↵

The server will respond with slot specif ic information:

202 slot info:↵

slot id: {Slot ID}↵

status: {“empty”, “mounting”, “error”, “mounted”}↵

volume name: {Volume name}↵

recording time: {recording time availa ble in seconds}↵

video format: {disk’s default video format}↵

↵

Asynchronous slot information change notif ication is disabled by default and may be configured with the
“notif y” command. When enabled, changes in slot state will generate a “502 slot info:” asynchronous
message with the same parameters as the “202 slot info:” message.

Retrieving clip information

The “disk list” command returns the information for each playable clip on a given disk. Without parameters,
the command returns information for the current active disk:

disk list↵

If a slot id is specified, the disk in that slot will be queried:

disk list: slot id: {Slot ID}↵

The server responds with the list of all playable clips on the disk in the format of: Index, name, formats, and
duration in timecode:

206 disk list:↵

slot id: {Slot ID}↵

{clip index}: {name} {file format} {video format} {Duration timecode}↵

{clip index}: {name} {file format} {video format} {Duration timecode}↵

…

↵

Note that the clip index starts from 1.

81Developer Information

Retrieving clip count

The "clips count" command returns the number of clips on the current timeline:

clips count ↵

The server responds with the number of clips:

214 clips count: ↵

clip count: {Count}↵

Retrieving timeline information

The “clips get” command returns information for each available clip, for a given range in timecode,
on the current timeline. Without parameters, the command returns information for all clips on timeline:

clips get↵

The server responds with a list of clip IDs, names and timecodes:

205 clips info:↵

clip count: {Count}↵

{Clip ID}: {Name} {Start timecode} {Duration timecode}↵

{Clip ID}: {Name} {Start timecode} {Duration timecode}↵

…

↵

Note that the clip list format has changed incompatibly in protocol version 1.1,

i.e., Star t timecode information field is inserted to each clip information line.

Retrieving transport information

The “transport info” command returns the state of the transport:

transport info ↵

The server responds with transport specific information:

208 transport info:↵

status: {“preview”, “stopped”, “play”, “forward”, “rewind”,

“ j o g ”, “ s h u t t l e ”, ” r e c o r d ” } ↵

speed: {Play speed between -1600 and 1600 %}↵

slot id: {Slot ID or “none”}↵

display timecode: {timecode}↵

timecode: {timecode}↵

clip id: {Clip ID or “none”}↵

video format: {Video format}↵

loop: {“true”, “false”}↵

↵

The “timecode” value is the timecode within the current timeline for playback or the clip for record. The
“display timecode” is the timecode displayed on the front of the deck. The two timecodes will differ in some
deck modes.

Asynchronous transport information change notification is disabled by default and may be configured with
the “notify” command. When enabled, changes in transport state will generate a “508 transport info:”
asynchronous message with the same parameters as the “208 transport info:” message.

82Developer Information

Video Formats

The following video formats are currently supported on HyperDeckExtreme 8K HDR:

NTSC, PAL, NTSCp, PALp

720p50, 720p5994, 720p60

1080p23976, 1080p24, 1080p25, 1080p2997, 1080p30

1080i50, 1080i5994, 1080i60

4Kp23976, 4Kp24, 4Kp25, 4Kp2997, 4Kp30

4Kp50, 4Kp5994, 4Kp60

Video format support may vary between models and software releases.

File Formats

HyperDeck Extreme 8K HDR supports the following file formats:

H.264Low

H.264Medium

H.264High

QuickTimeProResHQ

QuickTimeProRes

QuickTimeProResLT

Supported file formats may vary between models and software releases.

Querying and updating configuration information

The “configuration” command may be used to quer y the current configuration of the deck:

configuration↵

The server returns the configuration of the deck:

211 configuration:↵

audio input: {“embedded”, “XLR”, “RCA”}↵

video input: {“SDI”, “HDMI”, “component”}↵

file format: {File format}↵

↵

One or more configuration parameters may be specified to change the conf iguration of the deck.

To change the current video input:

configuration: video input: {“SDI”, “HDMI”, “component”}↵

Valid video inputs may vary between models. To configure the current audio input:

configuration: audio input: {“em bedded”, “XLR”, “RCA”}↵

Valid audio inputs may vary between models.

To configure the current file format:

configuration: file format: {File format}↵

Note that changes to the file format may require the deck to reset, which will cause the client connec tion to
be closed. In such case, response code 213 will be returned (instead of 200) before the client connection is
closed:

“213 deck rebooting”

Asynchronous configuration information change notification is disabled by default and may be configured
with the “notify” command. When enabled, changes in configuration will generate a “511 configuration:”
asynchronous message with the same parameters as the “211 configuration:” message.

83Developer Information

Selecting active slot and video format

The “slot select” command instructs the deck to switch to a specified slot, or/and to select a specified
output video format. To switch to a specified slot:

slot select: slot id: {slot ID}↵

To select the output video format:

slot select: video format: {video format}↵

Either or all slot select parameters may be specif ied. Note that selecting video format will result in a rescan
of the disk to reconstruct the timeline with all clips of the specified video format.

Clearing the current timeline

The "clips clear" command instruc ts the deck to empty the current timeline:

clips clear↵

The server responds with

200 ok↵

Adding a clip to the current timeline

The "clips add:" command instructs the deck to add a clip to the current timeline:

clips add: name: {"clip name"}↵

The server responds with

200 ok↵

or in case of error

1xx {error description}↵

Configuring the watchdog

The “watchdog” command instructs the deck to monitor the connected client and terminate the connection
if the client is inactive for at least a specified period of time.

To configure the watchdog:

watchdog: period: {period in seconds}↵

To avoid disconnection, the client must send a command to the server at least every {period} seconds. Note
that if the period is set to 0 or less than 0, connection monitoring will be disabled.

84Developer Information

Help

Getting Help

The fastest way to obtain help is to go to the Blackmagic Design online support pages and
check the latest support material available for your Blackmagic HyperDeck Disk Recorder.

Blackmagic Design Online Support Pages

The latest manual, software and support notes can be found at the Blackmagic Design support
center at www.blackmagicdesign.com/support.

Blackmagic Design Forum

The Blackmagic Design forum on our website is a helpful resource you can visit for more
information and creative ideas. This can also be a faster way of getting help as there may
already be answers you can find from other experienced users and Blackmagic Design staff
which will keep you moving forward. You can visit the forum at

https://forum.blackmagicdesign.com

Contacting Blackmagic Design Support

If you can’t find the help you need in our support material or on the forum, please use the
“Send us an email” button on the support page to email a support request. Alternatively,
click on the “Find your local support team” button on the support page and call your nearest
Blackmagic Design support office.

Checking the Software Version Currently Installed

To check which version of Blackmagic HyperDeck software is installed on your computer, open
the About Blackmagic HyperDeck Setup window.

 On Mac OS, open Blackmagic HyperDeck Setup from the Applications folder.

Select About Blackmagic HyperDeck Setup from the application menu to reveal the
version number.

 On Windows 7, open Blackmagic HyperDeck Setup from your Start menu. Click on

the Help menu and select About Blackmagic HyperDeck Setup to reveal the
version number.

 On Windows 8, open Blackmagic HyperDeck Setup from the Blackmagic

HyperDeck Setup tile on your Start page. Click on the Help menu and select About
Blackmagic HyperDeck Setup to reveal the version number.

How to Get the Latest Software Updates

After checking the version of Blackmagic HyperDeck Setup software installed on your
computer, please visit the Blackmagic Design support center at

www.blackmagicdesign.com/support to check for the latest updates. While it is usually a good

idea to run the latest updates, it is wise to avoid updating any software if you are in the middle
of an important project.

85Help

Regulatory Notices

Disposal of Waste of Electrical and Electronic Equipment Within the European Union.

The symbol on the product indicates that this equipment must not be disposed of with
other waste materials. In order to dispose of your waste equipment, it must be handed
over to a designated collection point for recycling. The separate collection and
recycling of your waste equipment at the time of disposal will help conserve natural
resources and ensure that it is recycled in a manner that protects human health and
theenvironment. Formore information about where you can drop off your waste
equipment for recycling, please contact your local city recycling office or the dealer
from whom you purchased the product.

This equipment has been tested and found to comply with the limits for a Class A
digitaldevice, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
inacommercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
maycause harmful interference to radio communications. Operation of this product in
aresidential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at personal expense.

Operation is subject to the following two conditions:

1 This device may not cause harmful interference.

2 This device must accept any interference received, including interference that

maycause undesired operation.

ISED Canada Statement

This device complies with Canadianstandards for Class A digital apparatus.

Any modifications or use of this product outside its intended use could void
complianceto these standards.

Connection to HDMI interfaces must be made with high quality shielded
HDMI cables.

This equipment has been tested for compliance with the intended use in a
commercialenvironment. If the equipment is used in a domestic environment,
itmaycause radio interference.

86Regulatory Notices

Safety Information

For protection against electric shock, the equipment must be connected to a mains socket
outlet with a protective earth connection. In case of doubt contact a qualifiedelectrician.

To reduce the risk of electric shock, do not expose this equipment to dripping orsplashing.

Ensure any DC power source connected to the units is compatible with the input voltage and
current rating marked at the DC IN connector.

Product is suitable for use in tropical locations with an ambient temperature of up to 40°C.

Ensure that adequate ventilation is provided around the product and that it is not restricted.

When rack mounting, ensure that the ventilation is not restricted by adjacent equipment.

No operator serviceable parts inside product. Refer servicing to your local Blackmagic Design
service center.

Use only at altitudes not more than 2000m above sea level.

State of California statement

This product can expose you to chemicals such as trace amounts of polybrominated biphenyls
within plastic parts, which is known to the state of California to cause cancer and birth defects
or other reproductive harm.

Formore information go to www.P65Warnings.ca.gov.

87Safety Information

Warranty

12 Month Limited Warranty

Blackmagic Design warrants that this product will be free from defects in materials and
workmanship for a period of 12 months from the date of purchase. If a product proves to be
defective during this warranty period, Blackmagic Design, at its option, either will repair the
defective product without charge for parts and labor, or will provide a replacement in exchange
for the defective product.

In order to obtain service under this warranty, you the Customer, must notify Blackmagic Design
of the defect before the expiration of the warranty period and make suitable arrangements for
the performance of service. The Customer shall be responsible for packaging and shipping the
defective product to a designated service center nominated by Blackmagic Design,
withshipping charges pre paid. Customer shall be responsible for paying all shipping charges,
insurance, duties, taxes, and any other charges for products returned to us for any reason.

This warranty shall not apply to any defect, failure or damage caused by improper use or
improper or inadequate maintenance and care. Blackmagic Design shall not be obligated to
furnish service under this warranty: a) to repair damage resulting from attempts by personnel
other than Blackmagic Design representatives to install, repair or service the product,
b) to repair damage resulting from improper use or connection to incompatible equipment,
c) to repair any damage or malfunction caused by the use of non Blackmagic Design parts or
supplies, or d) to service a product that has been modified or integrated with other products
when the effect of such a modification or integration increases the time or difficulty of servicing
the product. THIS WARRANTY IS GIVEN BY BLACKMAGIC DESIGN IN LIEU OF ANY OTHER
WARRANTIES, EXPRESS OR IMPLIED. BLACKMAGIC DESIGN AND ITS VENDORS DISCLAIM
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. BLACKMAGIC DESIGN’S RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE
PRODUCTS IS THE WHOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF
WHETHER BLACKMAGIC DESIGN OR THE VENDOR HAS ADVANCE NOTICE OF THE
POSSIBILITY OF SUCH DAMAGES. BLACKMAGIC DESIGN IS NOT LIABLE FOR ANY ILLEGAL
USE OF EQUIPMENT BY CUSTOMER. BLACKMAGIC IS NOT LIABLE FOR ANY DAMAGES
RESULTING FROM USE OF THIS PRODUCT. USER OPERATES THIS PRODUCT AT OWN RISK.

© Copyright 2019 Blackmagic Design. All rights reserved. ‘Blackmagic Design’, ‘DeckLink’, ‘HDLink’, ‘Workgroup Videohub’,
‘Multibridge Pro’, ‘Multibridge Extreme’, ‘Intensity’ and ‘Leading t he creat ive video revolution’ are regis tered trademarks in the
US and other countries. All other company and product names may be trade marks of t heir respect ive companies with which
they are associated.

88Warranty