This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Japane se ................................................................................................................ 54
Page 3
CHAPTER 1: INTRODUCTION
TP35D2-A7 SE
1.1 B
EFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
1.2PACKAGE CHECKLIST
HDD Cable X 1 Serial ATA Cable X 2 Rear I/O Panel for ATX Case X 1 User’s Manual X 1 Fully Setup Driver CD X 1 FDD Cable X 1 (optional) USB 2.0 Cable X1 (optional) S/PDIF out Cable X 1 (optional) Serial ATA Power Cable X 1 (optional)
Note : The package contents may differ by area or your motherboard version.
1
Page 4
Motherboard Manual
1.3 MOTHERBOARD FEATURES
Ver 5.x Ver 6.x
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pent iu m D / Pent ium 4 / C e leron D p ro ces sor
Supports Hyper-Threading / Exe cute D isable B it /
Enhanced Intel Sp eedStep® / Intel
Architecture-64 / Extend ed Memory 64
Technology / Virtualization Technology
Support 533 / 800 / 1066 / 1333 MHz
Support 1600 MHz (with DDR2 800)
Intel P35
Int e l IC H9
ITE 8718F
Prov ides t he most commonly us ed legacy Super
I/O functionality.
Low Pin Count Interface
En vironm ent C ont ro l initiatives ,
Hardware Monitor Controller
Fan Sp eed Controller
ITE's "S mart Guard ian " funct ion
DIMM Slots x 4
Each DIMM supports 256MB / 512MB / 1GB /
2GB DDR2
Max Memory Capicity 8GB
Dual Cha nn el Mode DDR 2 me mory modu le
Supports DDR2 800 / 667
Supports DDR2 533 (with FSB 533/1066 C PU)
Register ed D IMM and ECC D IMM is not
supported
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Vers ion 2.0 sp ecificat ion co mplian t
CPU
FSB
Chipset
Super I/O
Main
Memory
IDE
SATA 2
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pent iu m D / Pent ium 4 / C e leron D p ro ces sor
Supports Hyper-Threading / Exe cute D isable B it /
Enhanced Intel Sp eedStep® / Intel
Architecture-64 / Extend ed Memory 64
Technology / Virtualization Technology
Support 533 / 800 / 1066 / 1333 MHz
Support 1600 MHz (with DDR2 800)
Intel P35
Int e l IC H9
ITE 8718F
Prov ides t he most commonly us ed legacy Super
I/O functionality.
Low Pin Count Interface
En vironm ent C ont ro l initiatives ,
Hardware Monitor Controller
Fan Sp eed Controller
ITE's "S mart Guard ian " funct ion
DIMM Slots x 4
Each DIMM supports 256MB / 512MB / 1GB /
2GB DDR2
Max Memory Capicity 8GB
Dual Cha nn el Mode DDR 2 me mory modu le
Supports DDR2 800 / 667
Supports DDR2 533 (with FSB 533/1066 C PU)
Register ed D IMM and ECC D IMM is not
supported
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Vers ion 2.0 sp ecificat ion co mplian t
2
Page 5
TP35D2-A7 SE
Ver 5.x Ver 6.x
Realtek RTL 8110SC / 8100C (optional)
LAN
Sound
Codec
Slots
On Board
Connector
Back Panel
I/O
Board Size 220 (W) x 305 (L) mm 220 (W) x 305 (L) mm
OS Support
10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit
bandwidth is for RTL 8110SC only)
Half / Full duplex capability
ALC888
7.1 channels audio out
High Definition Audio
PCI slot x3 PCI slot x3
PCI Express x 16 slot x1 PCI Express x 16 slot x1
PCI Express x 4 slot x1 PCI Express x 4 slot x1
PCI Express x 1 slot x1 PCI Express x 1 slot x1
Floppy connecto r x1 Floppy connector x1
Printer Po rt Connector x1 Printer Port Connector x1
IDE Conn ect o r x1 ID E C onn ector x1
SATA Connector x4 SATA Connector x4
Front Panel Connector x1 Front Panel Connector x1
Front Audio Connector x1 Front Audio Connector x1
CD-in Connector x1 CD-in Connector x1
S/PDIF out connector x1 S/PDIF out connector x1
S/PDIF in connector(optional) x1 S/PDIF in connector(optional) x1
CPU Fan header x1 CPU Fan header x1
System Fan head er x2 S ystem Fan h ead er x2
Clear CMOS header x1 Clear C MOS he ader x1
USB connector x3 USB co nnector x3
Power Connector (24pin) x1 Power Conn ector (24pin) x 1
Power Connector (4pin) x1 Power Conn ector (4pin) x 1
PS/2 Keyboard x1
PS/2 Mouse x1
Serial Port x1
LAN port x1
USB Port x6
Audio Jack x6
Windows 2000 / XP / VISTA
Biostar Reserves the right to add or remove
support for any OS with or without notice
Realtek RTL 8110SC / 8100C (optional)
10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit
bandwidth is for RTL 8110SC only)
Half / Full duplex capability
ALC662
5.1 channels audio out
High Definition Audio
PS/2 Keyboard x1
PS/2 Mouse x1
Serial Port x1
LAN port x1
USB Port x6
Audio Jack x3
Windows 2000 / XP / VISTA
Biostar Reserves the right to add or remove
support for any OS with or without notice
3
Page 6
Motherboard Manual
1.4REAR PANEL CONNECTORS (FOR VER 5.X)
PS/2
Mouse
LA N
Audio Jack
Center
Rear
Si de
USBX2
Line In
Line Out
Mic In
PS/2
Keyboard
COM1USBX2USBX2
1.5REAR PANEL CONNECTORS (FOR VER 6.X)
PS/2
Mouse
PS/2
Keyboard
COM1USBX2USBX2
USBX2
LAN
Line In/
Surround
Line Out
Mic I n 1/
Bass/ Center
4
Page 7
1.6 MOTHERBOARD LAYOUT
TP35D2-A7 SE
JKBMS1
JPRNT1
JCOM1
JUSB2
JUSB1
JRJ45USB1
JA UDIO 1
(for Ver 5.x)
JAUDIO2
(for Ve r 6 .x )
Super
I/O
JNF AN1
JATXPWR1
PEX4_1
JATXPW R2
LGA775
CPU1
PEX16_1
Intel
P35
Intel
ICH9
JCFAN1
DDR2_A 1
DDR2_B 1
DDR2_A 2
DDR2_B 2
LAN
CO D E C
JAUDIOF1
Note: represents the 1■
JCDI N1
PEX1_1
JSPDIF_OUT1
BAT1
PCI1
PCI2
PCI3
JSPDIF_IN1(opti onal)
FDD1
st
pin.
BI O S
IDE
JUSB5
JUSB4
JUSB3
IDE 1
JPANEL1
JSFAN 1
SATA1SATA3
SATA2SATA4
RST SW2
JCMO S1
PWRSW1
LED 2
LE D1
5
Page 8
Motherboard Manual
CHAPTER 2: HARDWARE INSTALLATION
2.1 I
NSTALLING CENTRAL PROCESSING UNIT (CPU)
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.
Pin Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
6
Page 9
TP35D2-A7 SE
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:
Step 2-2:
Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.
7
Page 10
Motherboard Manual
2.2 FANHEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
Pin
Assignment
1 Ground
2 +12V
3
FAN RPM r ate
sense
4 Smart Fan
Control
Pin
Assignment
1 Ground
2 +12V
3 FAN RPM rate
sense
JSFAN1: System Fan Header
JNFAN1: Northbridge Fan Header
Note:
The JNFAN1/JSFAN1 support 3-pin head connectors, and the JCFAN1 supports 4-pin
head connector. When connecting with wires onto connectors, please note that the red
wire is the positive and should be connected to pin#2, and the black wire is Ground and
should be co nnected to GND.
4
1
13
JNFAN1
1
3
JSFAN1
8
Page 11
TP35D2-A7 SE
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules
DDR2 _A1
DDR2 _B1
DDR2 _A2
DDR2 _B2
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
9
Page 12
Motherboard Manual
B. Memory Capacity
DIMM Socket
Location
DDR2_A1 256MB/512MB/1GB/2GB
DDR2_A2 256MB/512MB/1GB/2GB
DDR2_B1 256MB/512MB/1GB/2GB
DDR2_B2 256MB/512MB/1GB/2GB
DDR Module
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status
Enabled O X O X
Enabled X O X O
Enabled O O O O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
DDR2_A1
Total Mem o ry
Size
Max is 8GB.
DDR2_A2 DDR2_B1 DDR2_B2
10
Page 13
TP35D2-A7 SE
2.4 CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
331
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.
39
34
2
1
240
11
Page 14
Motherboard Manual
PEX16_1: PCI-Express x16 Slot
- PCI-Express 1.0a compliant.
- Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PEX4_1: PCI-Express x4 Slot
- PCI-Express 1.0a compliant.
- Maximum theoretical realized bandwidth of 1GB/s simultaneously per
direction, for an aggregate of 2GB/s totally.
PEX1_1: PCI-Express x1 Slot
- PCI-Express 1.0a compliant.
- Maximum theoretical realized bandwidth of 250MB/s simultaneously per
This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
12
PCI1
PCI2
PCI3
Page 15
TP35D2-A7 SE
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 H
OW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened Pin closed Pin1-2 closed
3.2 D
JPANEL1: Front Panel Header
ETAIL SETTINGS
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
HLED
RST
8
16
SPK
+
-
1
9
++
-
On/Off
PWR_LED
Pin Assignment Function Pin Assignment Function
1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 11 N/ A N/A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control
Speaker
Connector
Hard drive
LED
Reset button
12 Power LED (+)
14 Power LED (-)
16 Ground
N/A
Power LED
Power-on button
13
Page 16
Motherboard Manual
JATXPWR2: AT X Power Source Connector
JATXPW2 allows user to connect 24-pin power connector on the AT X power
supply.
13
24
Pin Assignment Pin Assignment
1
12
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Gro und 3 Gro und
16 PS_ON 4 +5V
17 Gro und 5 Gro und
18 Ground 6 +5V
19 Gro und 7 Gro und
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
JATXPWR1: AT X Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
1
4
23
Pin
Assignment
1 +12V
2 +12V
3 Ground
4 Ground
14
Page 17
TP35D2-A7 SE
JUSB3/JUSB4/JUSB5: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
9
1
Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in
10 Jack Sense
10
2
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..
14
Assignment
Pin
1 Left Channel Input
2 Ground
3 Ground
4 Right Channel
Input
15
Page 18
Motherboard Manual
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
※ Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
3
1
3
Pin 2-3 Close:
Clear CMOS data.
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
16
SATA3 SATA1
SATA4 SATA2
7
14
Pin
Assignment
1 Ground
2 TX+
3 TX4 Ground
5 RX6 RX+
7 Ground
Page 19
TP35D2-A7 SE
JSPDIF_OUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
Assignment
1 +5V
2 SPDIF_OUT
3 Ground
13
JSPDIF_IN1: Digital Audio-in Connector (Optional)
This connector allows user to connect the PCI bracket SPDIF input header.
Pin
Assignment
1 +5V
2 SPDIF_IN
3 Ground
13
17
Page 20
Motherboard Manual
On-Board LED Indicators
There are 2 LED indicators on the motherboard to show system status.
LED1 and LED2:
These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:
LED1 LED2 Message
ON ON Norma l
ON OFF Memor y Er ror
OFF ON VGA Error
OFF OFF Abnormal: CPU / Chipset error.
LED2
LE D1
On-Board Buttons
There are 2 on-board buttons.
PWRSW1:
This is an on-board Power Switch button.
RSTSW2:
This is an on-board Reset button.
18
RSTSW2
PWRSW1
Page 21
JPRNT1: Printer Port Connector
This header allows you to connect printer on the PC.
Pin Assignment Pin Assignment
1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key
TP35D2-A7 SE
25
12
19
Page 22
Motherboard Manual
p
CHAPTER 4: T-SERIES BIOS & SOFTWARE
4.1 T-S
T-Series BIOS Features
ERIES BIOS
Overclocking Navigator Engine (O.N.E.)
CMOS Reloading Program (C.R.P.)
Memory Integration Test (M.I.T., under Overclock Navigator Engine)
Integrated Flash Program (I.F.P.)
Self Recovery System (S.R.S)
Smart Fan Function (under PC Health Status)
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board ma y be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.
NOTE
Overclock is an optional process, but not a “must-do” process; it is
not recommended for inexperienced users. Therefore, we will not
be responsible for any hardware damage which may be caused by
overclocking. We also would not guarantee any overclocking
erformance.
20
Page 23
TP35D2-A7 SE
A. Overclocking Navigator Engine (O.N.E.)
ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
Manual Overclock System (M.O.S.)
MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.
↓
21
Page 24
Motherboard Manual
CPU Clock Ratio & CPU C lock
CPU Clock Ratio x CPU Clock = CPU Frequency. CPU Frequency is
directly in proportion to system performance. To maintain the system
stability, CPU voltage needs to be increased also when raising CPU
frequency.
PCI-E Clock Select
It helps to increase VGA card performance.
Syste m Me mory Fre que ncy
To get better system performance, sometimes downgrading the memory
frequency is necessary when CPU frequency is adjusted over the upper
limit.
CPU Voltage
This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.
(G)MCH Voltage
This function lets you select the (G)MCH voltage.
FSB Termination Voltage
This function will increase chipset stability when overclocking.
Memory Voltage
This function will increase memory stability when overclocking.
Automatic Overclock System (A.O.S.)
For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.
Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.
22
Page 25
V6 Tech Engine
This engine will make a good over-clock performance.
V8 Tech Engine
This engine will make a better over-clock performance.
TP35D2-A7 SE
V12 Tech Engine
This engine will make a best over-clock performance.
23
Page 26
Motherboard Manual
B. CMOS Reloading Program (C.R.P.)
It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations.
Moreover, users are able to save an ideal overclock setting during overclock
operation.
There are 50 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.
24
Page 27
TP35D2-A7 SE
C. Memory Integration Test (M.I.T.)
This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or
software are needed.
Step 1
The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.
↓
Step 2
Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.
Step 3
When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.
25
Page 28
Motherboard Manual
D. Self Recovery System (S.R.S.)
This function can’t be seen under BIOS setup; and is always on whenever the
system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.
E. Integrated Flash Program (I.F.P.)
IFP is a safe and quick way to upgrade BIOS.
Step 1
Go to the website to download the latest BIOS file. Then, save the file into a
floppy disk.
Step 2
Insert the floppy disk and reboot the system to get into CMOS screen.
Step 3
Select the item “Integrated Flash Program” to get the following frame and
choose the BIOS file downloaded in step 1.
26
Step 4
Press “Enter” key to start BIOS file loading, and BIOS updating will process
automatically.
Step 5
When the BIOS update is completed, press YES to the message “Flash done,
Reset system”, and the system will reboot automatically to finish the process.
Advise:
You can update the system BIOS by simply pressing “Enter” key for three times.
Page 29
TP35D2-A7 SE
F. Smart Fan Function
Smart Fan Function is under “Smart Fan Option” in “PC Health Status”.
This is a brilliant feature to control CPU/System Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by
CPU/System temperature.
This function will protect CPU/System from overheat problem and maintain the
system temperature at a safe level.
↓
Smart Fan Calibration
Choose this item and then the BIOS will automatically test and detect the
CPU/System fan functions and show CPU/System fan speed.
PWM Duty Off <℃>
If the CPU/System temperature is lower than the set value, the
CPU/System fan will turn off. The range is from 0℃~127℃, with an
interval of 1℃.
27
Page 30
Motherboard Manual
PWM Duty Start <℃>
The CPU/System fan starts to work when CPU/System temperature
arrives to this set value. The range is from 0℃~127℃, with an interval of
1℃.
Start PWM Value
When CPU/System temperature arrives to the set value, the CPU/System
fan will work under Smart Fan Function mode. The range is from 0~127,
with an interval of 1.
Smart Fan Slope
Increasing the value of slope PWM will raise the speed of CPU/System fan.
The range is from 1~127, with an interval of 1.
28
Page 31
TP35D2-A7 SE
4.2 T-SERIES SOFTWARE
Installing T-Series Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software In stallation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching T-Series Software
After the installation process, you will see the software icon “HW Monitor”/
“eHOT Line” / “Tseries BIOS Update” appears on the desktop. Double-click
the icon to launch T-Series utility.
Hardware Monitor
HW Monitor is a monitor utility that helps you to maintain the health of the PC.
It provides real-time information of CPU/GPU/System temperature, fan speed,
and voltage.
Thi s area sh ows vol tag e inf ormat ion
Vol ta ge PanelFan Pa nel
Thi s area sh ows CPU in fo rma tion
Thi s area s hows CPU/ Syst em tem per atur e
Tu rn t o Fa n Pa nel
Thi s area sh ows CPU/ Syst em fan spee d
Turn to Voltage Panel
29
Page 32
Motherboard Manual
e
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this uti lity, please set Outlook E xpress as your default e-mail client application prog ram.
rep resents import ant
*
information that you
must provi de. Withou t
this informat ion, you ma y
not be able to send ou t
the mail.
This block will show
the infor mation which
would be collect ed in
the mail.
Send the mail ou t.
Describe co ndition
*
of your syst em.
Save these information to a .txt fil
Exit this dialog.
Select your area or
*
the area clos e to yo u.
Provid e the e-mail
addres s that you woul d
like to se nd the copy to.
Provide t he name of
*
the memory module
manufactu rer.
Provid e the name of
the power supply
manufac turer and the
model no .
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialo g appears asking you to enter file name.
30
Page 33
Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.
We will not share customer ’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
TP35D2-A7 SE
Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
31
Page 34
Motherboard Manual
BIOS Update
BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.
AWARD BIOSAMI BIOS
Clear CMOS function
(Only for AWARD BIOS)
Show current BIOS information
Save cur rent BIOS
to a .bin file
Update BIOS
with a BIOS file
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.
32
After the saving process, finish
dialog will show. Click on OK to
complete the BIOS Backup
procedure.
Page 35
TP35D2-A7 SE
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.
After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.
After the BIOS Update process, click on
OK to restart the system.
While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.
In the BIOS setup, use the Load Optimized Defaults function and then Save and Exit Setup to exit BIOS setup. BIOS Update is completed.
All the information and content above about the T-Series software are subject to be
changed without notice. For better performance, the software is being continuously
updated. The information and pictures described above are for your reference only.
The actual i nformation and settings on board may be slightly different from this
manual.
33
Page 36
Motherboard Manual
CHAPTER 5: USEFUL HELP
5.1 D
RIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html
34
Page 37
5.2 AWARD BIOSBEEP CODE
Beep Sound Meaning
One long beep followed by two short
beeps
High-low siren sound CPU overheated
One Short beep when system boot-up No error found during POST
Long beeps every other second No DRAM detected or install
Video card not found or video card
memory bad
System will shut down automatically
5.3 EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdow n
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
TP35D2-A7 SE
35
Page 38
Motherboard Manual
5.4 TROUBLESHOOTING
Probable Solution
1. No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.
2. Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.
System does not boot from hard disk
drive, can be booted from optical drive.
System only boots from optical drive.
Hard disk can be read and applications
can be used but booting from hard disk
is impossible.
Screen message says “Invalid
Configuration” or “CMOS Failure.”
Cannot boot system after installing
second hard drive.
1. Make sure power cable is
securely plugged in.
2. Replace cable.
3. Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
1. Back up data and applications
files.
2. Reformat the hard drive.
Re-install applications and data
using backup disks.
Review system’s equipment. Make sure
correct information is in setup.
1. Set master/slave jumpers
correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
36
Page 39
TP35D2-A7 SE
This page is intentionally left blank.
37
Page 40
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
G
ERMAN
Ver 5.x Ver 6.x
CPU
FSB
Chipsatz
Super E/A
Arbeitsspeich
er
IDE
SATA
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pent iu m 4 / Pent ium D / C e leron D Proz es s oren
Unterstützt Hyper-Threading / Execute Disable
Bit / Enhanced Intel SpeedStep® / Intel
Architecture-64 / Extend ed Memory 64
Technology / Virtualization Technology
533 / 800 / 1066 / 1333 MHz
1600 MHz (with DDR2 800)
Intel P35
Int e l IC H9
ITE 8718F
Biet et die häufig ver wend eten alten Super
E/A-Funktionen.
Low Pin Count-Schnittstelle
Umgebungskontrolle,
Hardware-Überwachung
Lüfterdrehzahl-Controller/-Überwachung
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 4
Jeder DIMM unte rstützt 256MB / 512 MB / 1GB /
2GB DDR2.
Max. 8GB Arbeitsspeicher
Dual-Kanal DDR2 Speichermodul
Unterstützt DDR2 800 / 667
Unterstützt DDR2 533 (w. FSB 533/1066 CPU)
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus
Master-Modus
Unterstützt PIO-Modus 0~4,
Integrierter Serial ATA-Controller
Datentransferrate b is zu 3.0Gb/s
Konform mit d er SATA-Spezifikation Version 2.0.
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pent iu m 4 / Pent ium D / C e leron D Proz es s oren
Unterstützt Hyper-Threading / Execute Disable
Bit / Enhanced Intel SpeedStep® / Intel
Architecture-64 / Extend ed Memory 64
Technology / Virtualization Technology
533 / 800 / 1066 / 1333 MHz
1600 MHz (with DDR2 800)
Intel P35
Int e l IC H9
ITE 8718F
Biet et die häufig ver wend eten alten Super
E/A-Funktionen.
Low Pin Count-Schnittstelle
Umgebungskontrolle,
Hardware-Überwachung
Lüfterdrehzahl-Controller/-Überwachung
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 4
Jeder DIMM unte rstützt 256MB / 512 MB / 1GB /
2GB DDR2.
Max. 8GB Arbeitsspeicher
Dual-Kanal DDR2 Speichermodul
Unterstützt DDR2 800 / 667
Unterstützt DDR2 533 (w. FSB 533/1066 CPU)
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus
Master-Modus
Unterstützt PIO-Modus 0~4,
Integrierter Serial ATA-Controller
Datentransferrate b is zu 3.0Gb/s
Konform mit d er SATA-Spezifikation Version 2.0.
38
Page 41
TP35D2-A7 SE
Ver 5.x Ver 6.x
Realtek RTL 8110SC / RTL 8100C(opt ional)
LAN
HD
Audio-Unters
tützung
Steckplätze
Onboard-Ans
chluss
Rückseiten-E
/A
Platinengröße 220 mm (B) X 305 mm (L) 220 mm (B) X 305 mm (L)
Connecteur de disquette x1 Connecteur de disquette x1
Connecteur de Port d'imprimante x1 Connecteur de Port d'imprimante x1
Connecteur IDE x1 Connecteur IDE x1
Connecteur SATA x4 Connecteur SATA x4
Connecteur du panneau avant x1 Connecteur du panneau avant x1
Connecteur Audio du panneau avant x1 Connecteur Audio du panneau avant x1
Connecteur d' entrée CD x1 Connecteur d'entré e CD x1
Connecteur de sortie S/PDIF x1 Connecteur de sortie S/PDIF x1
Connecteur d' entrée S/PD IF(en option) x1 Connecteur d'entré e S/ PDIF(en option) x 1
Embase de ventilateur UC x1 Embase de ventilateur UC x1
Embase de ventilateur système x2 Embase de ventilateur système x2
Embase d'effacement CMOS x1 Embase d'effacement CMOS x1
Connecteur USB x3 Connecteur USB x3
Connecteur d' aliment at ion x 1
(24 broches)
Connecteur d' aliment at ion x1
(4 broch es)
Clavier PS/2 x1
Souris PS/2 x1
Port série x1
Port LA N x1
Port USB x6
Fiche aud io x6
220 mm (l) X 305 mm (H) 220 mm (l) X 305 mm (H)
Windows 2000 / XP / VISTA
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis.
ITE 8718F
Fo rn isce le funz ionalità lega cy S uper I/O
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co ntro ller / Mo nito raggio velocit à vent olin a
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2 256MB /
512MB / 1GB / 2GB
Capacità massima della memoria 8GB
Modulo di memoria DDR2 a canale doppio
Supporto di DDR2 800 / 667
Supporto di DDR2 533 (w. FSB 533/1066
CPU)
DIMM r egistrati e DIMM ECC non sono
supportati
JMicro JMB368
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
Supporto modalità PIO Mode 0-4
Co ntro ller Serial ATA integrato
Velocità di trasferimento dei dati fino a
3.0Gb/s.
Co mpatibile s pecifiche SATA Versione 2.0.
ITE 8718F
Fo rn isce le funz ionalità lega cy S uper I/O
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co ntro ller / Mo nito raggio velocit à vent olin a
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2 256MB /
512MB / 1GB / 2GB
Capacità massima della memoria 8GB
Modulo di memoria DDR2 a canale doppio
Supporto di DDR2 800 / 667
Supporto di DDR2 533 (w. FSB 533/1066
CPU)
DIMM r egistrati e DIMM ECC non sono
supportati
JMicro JMB368
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
Supporto modalità PIO Mode 0-4
Co ntro ller Serial ATA integrato
Velocità di trasferimento dei dati fino a
3.0Gb/s.
Co mpatibile s pecifiche SATA Versione 2.0.
42
Page 45
TP35D2-A7 SE
Ver 5.x Ver 6.x
LAN
Supporto
audio HD
Allo ggi
Connettori
su scheda
I/O
pannello
posteriore
Dimension
i scheda
Sistemi
operativi
supportati
Realtek RTL 8110SC / RTL 8100C(opt ional)
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo
per RTL 8110SC)
Capacità Half / Full Dup lex
ALC888
Supporto audio High-Definition (HD)
Uscita audio 7.1 canali
Allo ggio PC I x3 Allog gio PC I x3
Alloggio PCI Express x16 x1 Alloggio PCI Express x16 x1
Alloggio PCI Express x4 x1 Alloggio PCI Express x4 x1
Alloggio PCI Express x1 x1 Alloggio PCI Express x1 x1
Connettore floppy x1 Connettore floppy x1
Connettore Porta stampante x1 Connettore Porta stampante x1
Connettore IDE x1 Connettore IDE x1
Connettore SATA x 4 Conn ettore SATA x4
Connettore pannello frontale x1 Connettore pannello frontale x1
Connettore audio frontale x1 Connettore audio frontale x1
Connettore CD-in x1 Connettore CD-in x1
Connettore output SPDIF x1 Connettore output SPDIF x1
Connettore input SPDIF(optional) x1 Connettore input SPDIF(optional) x1
Co llet tor e vent olina C PU x 1 Collett o re vento lina C PU x1
Co llet tor e vent olina s is tema x2 C olletto re ven tolina sistema x2
Co llet tor e cance llaz io ne CMOS x1 Collett ore cancel laz io ne CMOS x1
Connettore USB x3 Connettore USB x3
Connetto re alimentazione x 1
(24 pin)
Connetto re alimentazione x1
(4 pin)
Tas ti era PS/2 x 1
Mou se PS /2 x 1
Porta seriale x1
Porta LAN x 1
Porta USB x6
Connettore audio x6
220 mm (larghezza) x 305 mm (altezza) 220 mm (larghezza) x 305 mm (altezza)
Windows 2000 / XP / VISTA
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
Realtek RTL 8110SC / RTL 8100C(opt ional)
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo
per RTL 8110SC)
Capacità Half / Full Dup lex
ALC662
Supporto audio High-Definition (HD)
Uscita audio 5.1 canali
Connetto re alimentazione x 1
(24 pin)
Connetto re alimentazione x1
(4 pin)
Tas ti era PS/2 x 1
Mou se PS /2 x 1
Porta seriale x1
Porta LAN x 1
Porta USB x6
Connettore audio x3
Windows 2000 / XP / VISTA
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
43
Page 46
Motherboard Manual
SPANISH
Ver 5.x Ver 6.x
LGA 775
Procesador Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D
Admite Hyper-Threading / Bit de deshabilitación
Intel P35
Int e l IC H9
ITE 8718F
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
Interface LPC (Low Pin Count).
In ic iat ivas p ar a con tro lo do a mb iente
Monitorização do hardware
Controlador/Monitor da velocidade da ventoinha
Função "Smart Gu ardian" da ITE
Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
DDR2 de 256 MB / 512 MB / 1GB / 2GB
Capac idade máx ima d e memór ia:8 GB
Módulo de memória DDR2 de canal duplo
Suporta módulos DDR2 800 / 667
Suporta módulos DDR2 533 (w. FSB 533/1066
CPU)
Os módulos DIMM registados e os DIMM ECC
não são suportados
JMicro JMB368
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
Controlador Serial ATA integrado
Velocidades de transmissão de dados até 3.0
Gb/s.
Co mpat ibilidade co m a esp ecif icação SATA
versão 2.0 .
Realtek RTL 8110SC / RTL 8100C(opcional)
Auto negociação de 10 / 100 / 1000 Mb/s (a
largura de banda Gigabit refere-se apenas à
especificação RTL 8110SC)
Capacidade semi/full-duplex
LGA 775
Processador Intel Cor e2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D
Suporta as tecno log ias Hyper-Thr ead ing /
Execute D isab le B it / Enhanced Intel
SpeedStep® / Intel Arquitecture -64 / Extended
Memory 64 / Virtualization
Intel P35
Int e l IC H9
ITE 8718F
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
Interface LPC (Low Pin Count).
In ic iat ivas p ar a con tro lo do a mb iente
Monitorização do hardware
Controlador/Monitor da velocidade da ventoinha
Função "Smart Gu ardian" da ITE
Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
DDR2 de 256 MB / 512 MB / 1GB / 2GB
Capac idade máx ima d e memór ia:8 GB
Módulo de memória DDR2 de canal duplo
Suporta módulos DDR2 800 / 667
Suporta módulos DDR2 533 (w. FSB 533/1066
CPU)
Os módulos DIMM registados e os DIMM ECC
não são suportados
JMicro JMB368
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
Controlador Serial ATA integrado
Velocidades de transmissão de dados até 3.0
Gb/s.
Co mpat ibilidade co m a esp ecif icação SATA
versão 2.0 .
Realtek RTL 8110SC / RTL 8100C(opcional)
Auto negociação de 10 / 100 / 1000 Mb/s (a
largura de banda Gigabit refere-se apenas à
especificação RTL 8110SC)
Capacidade semi/full-duplex
Page 49
TP35D2-A7 SE
Ver 5.x Ver 6.x
Suporte
para áudio
de alta
definição
Ranhuras
Conectores
na placa
Entradas /S
aídas no
painel
traseiro
Tamanho
da placa
Sistemas
operativos
suportados
ALC888
Suporta a especificação High-Definition Audio
Saída de áudio de 7.1 canais
Conector da unidade de disquetes x1 Conector da unidade de disquetes x1
Conector da para impressora x1 Conector da para impressora x1
Conector IDE x1 Conector IDE x1
Conector SATA x4 Conector SATA x4
Conector do painel frontal x1 Conector do painel frontal x1
Conector de áudio frontal x1 Conector de áudio frontal x1
Conecto r par a ent rada de CDs x1 Conector para entrada d e CDs x 1
Conector de saída S/PDIF x1 Conector de saída S/PDIF x1
Conector de entrada S/PDIF(opcional) x1 Conector de entrada S/PDIF(opcional) x1
Conector da ventoinha da CPU x1 Conector da vento inha da CPU x1
Conector da ventoinha do s istema x2 Conector da ventoinha do sistema x2
Conector para limpeza do CMOS x1 Conector para limpeza do CMOS x1
Conector USB x3 Conector USB x3
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(4 p inos )
Tec lad o PS /2 x1
Rato PS/2 x1
Porta série x1
Porta LAN x1
Porta USB x6
Tomada de áudio x6
220 mm (L) X 305 mm (A) 220 mm (L) X 305 mm (A)
Windows 2000 / XP / VISTA
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.
ALC662
Suporta a especificação High-Definition Audio
Saída de áudio de 5.1 canais
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(4 p inos )
Tec lad o PS /2 x1
Rato PS/2 x1
Porta série x1
Porta LAN x1
Porta USB x6
Tomada de áudio x3
Windows 2000 / XP / VISTA
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.
Intel P35
Int e l IC H9
Gniazda DDR2 DIMM x 4
Każde gniazdo DIMM obs ługuje moduły 256MB /
512MB / 1GB / 2GB
Maks. wielko ść pamięci 8GB
Mod uł pamięci DDR2 z trybem podwójnego
kana łu
Obsługa DDR2 800 / 667
Obsługa DDR2 533 (w. FSB 533/1066 CPU)
Brak obsług i Registered DIMM oraz ECC DIMM
ITE 8718F
Zapewnia najbardziej powszechne funkcje Super
I/O.
Interfejs Low Pin Count
Funkcje kontroli warunków pracy,
Mon itor H /W
Kontroler/Monitor prędkości wentylatora
Funkcja ITE "Sm art Gu ard ian"
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
Zintegrowany kontroler Serial ATA
Transfer danych do 3.0 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2. 0.
Realtek RTL 8110SC / RTL 8100C (opcja)
10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją
szybkości (Pasmo gigabitowe wyłącz nie dla RTL
8110SC)
Działanie w trybie połowicznego / pełnego
dupleksu
Intel P35
Int e l IC H9
Gniazda DDR2 DIMM x 4
Każde gniazdo DIMM obs ługuje moduły 256MB /
512MB / 1GB / 2GB
Maks. wielko ść pamięci 8GB
Mod uł pamięci DDR2 z trybem podwójnego
kana łu
Obsługa DDR2 800 / 667
Obsługa DDR2 533 (w. FSB 533/1066 CPU)
Brak obsług i Registered DIMM oraz ECC DIMM
ITE 8718F
Zapewnia najbardziej powszechne funkcje Super
I/O.
Interfejs Low Pin Count
Funkcje kontroli warunków pracy,
Mon itor H /W
Kontroler/Monitor prędkości wentylatora
Funkcja ITE "Sm art Gu ard ian"
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
Zintegrowany kontroler Serial ATA
Transfer danych do 3.0 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2. 0.
Realtek RTL 8110SC / RTL 8100C (opcja)
10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją
szybkości (Pasmo gigabitowe wyłącz nie dla RTL
8110SC)
Działanie w trybie połowicznego / pełnego
dupleksu
Gniazdo PCI Express x 4 x1 Gniazdo PCI Express x 4 x1
Gniazdo PCI Express x 1 x1 Gniazdo PCI Express x 1 x1
Złącze napędu dyskietek x1 Złącze napędu dyskietek x1
Złącze Port drukarki x1 Złącze Port drukarki x1
Złącze IDE x1 Złącze IDE x1
Złącze SATA x4 Złącze S ATA x4
Złącze panela przedniego x1 Złącze panela przedniego x1
Przedn ie złącze aud io x1 Przednie złącze aud io x1
Złącze wejścia CD x1 Złącze wejścia CD x1
Złącze wyjścia S/PDIF x1 Złącze wyjścia S/PDIF x1
Złącze wejścia S/PDIF (opcja) x1 Złącze wejścia S/PDIF (opcja) x1
Złącze głó wko we wentylato ra
procesora x1
Złącze głó wko we wentylato ra
systemowego x2
Złącze głó wkowe kaso wan ia CMOS x1 Złącze głó wkowe kaso wan ia CMOS x1
Złącze USB x3 Złącze USB x3
Złącze zasilania (24 pinowe) x1 Złącze zasilania (24 pinowe) x1
Złącze zas ilania (4 p ino we) x 1 Złącze zas ilania (4 p ino we) x 1
Klawiatura PS/2 x1
Mys z PS /2 x1
Port sz eregowy x 1
Port LA N x1
Port USB x6
Gniazdo audio x6
220 mm (S) X 305 mm (W) 220 mm (S) X 305 mm (W)
Windows 2000 / XP / VISTA
Biostar zastrzega sobie prawo dodawania lub
odwoływ ania obs ług i dowo ln eg o systemu
operacyjnego b ez powiado mien ia.
ALC662
Obsługa H igh -Defin ition Aud io
5.1 kanałowe wyjście audio
Złącze głó wko we wentylato ra
procesora x1
Złącze głó wko we wentylato ra
systemowego x2
Klawiatura PS/2 x1
Mys z PS /2 x1
Port sz eregowy x 1
Port LA N x1
Port USB x6
Gniazdo audio x3
Windows 2000 / XP / VISTA
Biostar zastrzega sobie prawo dodawania lub
odwoływ ania obs ług i dowo ln eg o systemu
operacyjnego b ez powiado mien ia.
49
Page 52
Motherboard Manual
RUSSIAN
Ver 5.x Ver 6.x
CPU
(центральн
ый
процессор)
FSB
Набо р
микросхем
Основная
память
Super I/O
IDE
SATA
Локальна я
сеть
50
LGA 775
Процессор Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D
Поддержкатехнологий Hyper-Threading /
Execute D isab le B it / Enhanced Intel
SpeedStep® / Intel Ar chitect ure-64 / Extended
Memory 64 Technology / технологии виртуализация
533 / 800 / 1066 / 1333 МГц
1600 МГ ц (with DDR2 800)
Intel P35
Int e l IC H9
Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает 256 МБ /
512МБ / 1ГБ / 2ГБ DDR2
Максимальная ёмкость памяти 8ГБ
Мод ул ь памяти с двухканальн ым режимом
DDR2
Поддержка DDR2 800 / 667
Поддержка DDR2 533 (w. FSB 533/1066 CPU)
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM
ITE 8718F
Обеспечивает наиболее используемые
действующие фун кц ион альны е во зможнос ти
Super I/O.
Интерфейс с ни зким количеством выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ятор скорости вентилятора/ монитор
Функция ITE "Smart Guardian"
(Интеллектуальная защита)
JMicro JMB368
Режим "хозяина" шины U ltra DMA 3 3 / 66 / 100
/ 133
Поддержка режима PIO 0~4,
Встроенное последоват ельное устройство
упра влени я ATA
скорость передачи данных до 3.0 гигабит/с.
Соответствие специ фикации SATA версия 2.0.
LGA 775
Процессор Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D
Поддержкатехнологий Hyper-Threading /
Execute D isab le B it / Enhanced Intel
SpeedStep® / Intel Ar chitect ure-64 / Extended
Memory 64 Technology / технологии виртуализация
533 / 800 / 1066 / 1333 МГц
1600 МГ ц (with DDR2 800)
Intel P35
Int e l IC H9
Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает 256 МБ /
512МБ / 1ГБ / 2ГБ DDR2
Максимальная ёмкость памяти 8ГБ
Мод ул ь памяти с двухкан альн ым режимом
DDR2
Поддержка DDR2 800 / 667
Поддержка DDR2 533 (w. FSB 533/1066 CPU)
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM
ITE 8718F
Обеспечивает наиболее используемые
действующие фун кц ион альны е во зможнос ти
Super I/O.
Интерфейс с ни зким количеством выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ятор скорости вентилятора/ монитор
Функция ITE "Smart Guardian"
(Интеллектуальная защита)
JMicro JMB368
Режим "хозяина" шины U ltra DMA 33 / 66 / 100
/ 133
Поддержка режима PIO 0~4,
Встроенное последоват ельное устройство
упра влени я ATA
скорость передачи данных до 3.0 гигабит/с.
Соответствие специ фикации SATA версия 2.0.