Biostar TF520 A2+ Owner's Manual

TF520 A2+/TF560 A2+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment ge nerates, uses, and can radiate radio frequency
energy and, if not i nstalled and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors (Ver 5.x)..................................................... 4

1.5 Rear Panel Connectors (Ver 6.x)..................................................... 4

1.6 Motherboard Layout......................................................................... 5

Chapter 2: Hardware Installation........................... 6

2.1 Installing Central Processing Unit (CPU) ....................................... 6

2.2 FAN Headers...................................................................................... 8

2.3 Installing System Memory ................................................................ 9

2.4 Connectors and Slots....................................................................... 11

Chapter 3: Headers & Jumpers Setup ................... 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: NVIDIA RAID Functions...................... 20

4.1 Operation System............................................................................ 20

4.2 Raid Arrays...................................................................................... 20

4.3 How RAID Works............................................................................. 20

Chapter 5: OverClock Quick Guide ....................... 24

5.1 T-Power Introduction...................................................................... 24

5.2 T-Power BIOS Feature.................................................................... 25

5.3 T-Power Windows Feature ............................................................ 33

Chapter 6: Useful Help......................................... 38

6.1 Driver Installation Note.................................................................. 38

6.2 Award BIOS Beep Code.................................................................. 39

6.3 Extra Information............................................................................ 39

6.4 Troubleshooting............................................................................... 41

Appendencies: SPEC In Other Language .............. 42

German.................................................................................................................. 42

France .................................................................................................................... 44

Italian..................................................................................................................... 46

Spanish ................................................................................................................... 48

Portugue se ............................................................................................................ 50

Polish...................................................................................................................... 52

Russian ................................................................................................................... 54

Arabic..................................................................................................................... 56

Japanese ................................................................................................................ 58

CHAPTER 1: INTRODUCTION

TF520 A2+/TF560 A2+

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
Serial ATA Power Cable X 1 (optional)

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

TF520 A2+ TF560 A2+

Socket AM2 / AM2+ (By BIOS updat e)

AMD Athlon 64 / Athlon 64 x2 / Sempron

CPU

FSB

Chipset nVIDIA nForce 520 nVIDIA nForce 560

Super I/O

Main

Memory

IDE

SATA II

LAN

processors

AMD 64 Architecture enables 32 and 64 bit

computing

Supports Hyper Transport and Cool=n=Quiet

Support up to 1 GHz Bandwidth

Support HyperTransport

ITE 8716F

Prov ides the most commonly us ed legacy Super

I/O functionality.

Low Pin Count Interface

En v ironm en t Cont r ol in it iatives ,

H/W Mon ito r

Fan Sp eed Controller

ITE's "S mart Guard ian" function

DIMM Slots x 4

Each DIMM supports 256/512MB & 1GB/2GB

DDR2

Max Memory Capicity 8GB

Dual Channel Mode DDR2 me mory mo du le

Supports DDR2 533 / 667 / 800

Register ed D IMM and ECC D IMM is not

supported

Int egr at ed ID E Contro ller

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4.

Integrated Serial ATA Controller

Data transfer rates up to 3 Gb/s.

SATA Version 2.0 s p e c if icat ion co mpliant .

Realtek RTL 8110SC / 8100C (optional)

10 / 100 Mb/s / 1Gb/s auto negot iation (Gigabit

bandwidth is for RTL 8110SC only)

Half / Full duplex capability

2

Socket AM2 / AM2+ (By BIOS updat e)

AMD Athlon 64 / Athlon 64 x2 / Sempron

processors

AMD 64 Architecture enables 32 and 64 bit

computing

Supports Hyper Transport and Cool=n=Quiet

Support up to 1 GHz Bandwidth

Support HyperTransport

ITE 8716F

Prov ides the most common ly used lega cy Supe r

I/O functionality.

Low Pin Count Interface

En v ironm en t Cont r ol in it iatives ,

H/W Mon ito r

Fan Sp eed Controller

ITE's "S mart Guard ian" function

DIMM Slots x 4

Each DIMM supports 256/512MB & 1GB/2GB

DDR2

Max Memory Capicity 8GB

Dual Channel Mode DDR2 me mory mo du le

Supports DDR2 533 / 667 / 800

Register ed D IMM and ECC D IMM is not

supported

Int egr at ed ID E Contro ller

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4.

Integrated Serial ATA Controller

Data transfer rates up to 3 Gb/s.

SATA Version 2.0 s p e c if icat ion co mpliant .

Realtek RTL 8110SC / 8100C (optional)

10 / 100 Mb/s / 1Gb/s auto negot iation (Gigabit

bandwidth is for RTL 8110SC only)

Half / Full duplex capability

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

Sound

Slots

On Board

Connector

Back Panel

I/O

Board Size 244 mm (W) x 305 mm (L) 244 mm (W) x 305 mm (L)

Special

Features

OS Support

7.1 channels audio out (ALC888)

5.1 channels audio out (ALC662)

HD Aud io

PCI slot x3 PCI slot x3

PCI Express x16 slot x1 PCI Express x16 slot x1

PCI Express x 1 slot x2 PCI Express x 1 slot x2

Floppy connector x1 Floppy connecto r x1

Printer Port conne ctor x1 Printer Port connect or x1

IDE Conn ector x1 ID E Co nnector x1

SATA Connector x4 SATA Connector x4

Front Panel Connector x1 Front Panel Connector x1

Front Audio Connector x1 Front Audio Connector x1

CD-in Connector x1 CD-in Connector x1

S/PDIF out connector x1 S/PDIF out connector x1

CPU Fan header x1 CPU Fan header x1

System Fan head er x2 System Fan head er x2

CMOS clear header x1 CMOS clear header x1

USB connector x2 USB connector x 2

Power Connector (24pin) x1 Power Connector (24pin) x1

Power Connector (4pin) x2 Power Connector (4pin) x2

PS/2 Keyboard x1

PS/2 Mous e x1

Serial Port x1

LAN port x1

USB Port x6

Audio Jack (Ver 5.x) x6

Audio Jack (Ver 6.x) x3

NVIDIA nTunes

RAID 0 / 1 / 0+1 support

Windows 2K / XP / V ISTA

Biostar Reserves the right to add or remove

support for any OS With or without notice.

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1 channels audio out (ALC888)

5.1 channels audio out (ALC662)

HD Aud io

PS/2 Keyboard x1

PS/2 Mous e x1

Serial Port x1

LAN port x1

USB Port x6

Audio Jack (Ver 5.x) x6

Audio Jack (Ver 6.x) x3

NVIDIA nTunes

RAID 0 / 1 / 0+1 / 5 support

Windows 2K / XP / V ISTA

Biostar Reserves the right to add or remove

support for any OS With or without notice.

3

Motherboard Manual

1.4 REAR PANEL CONNECTORS (VER 5.X)

PS/2
Mouse

LAN

PS/2
Keyboard

COM1 USB X2USBX2

Center

Rear

Side

USBX2

Line In

Line Out

Mic In

1.5 REAR PANEL CONNECTORS (VER 6.X)

PS/2
Mou se

PS/ 2
Keybo ard

COM1 USB X2USB X2

USB X2

LAN

Line In/
Surround

Line Out

Mic In 1/
Bass/ Center

4

1.6 MOTHERBOARD LAYOUT

JKBMS1

JCOM1

JUSB2

JATXPWR2

JUSB1

JUSBLAN1

AU DIO 2

(for Ve r 5.x )

JAUDIO1

(for Ve r 6.x)

JATXPWR3

nForce

520/560

PEX1_1

LAN

PEX1_2

PEX16_1

TF520 A2+/TF560 A2+

JCFAN1

DIMMA1

DIMMB1

DIMMB2

DIMMA2

SATA3

SATA1

SATA2

SATA4

BIOS

IDE1

JATXPWR1

FDD1

PCI1

Codec

PCI2

PCI3

JCDIN1

JSPDIF_OUT

JPRNT1

JCMOS1

JAUDIOF1

Note: ■ represents the 1st pin.

JUSB3 JUSB4

SUPER I/O

JSF AN1

JSFAN2

JPANEL1

BAT1

LED_D1

LED_D2

PWRSW1RSTSW1

5

Motherboard Manual

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point forwards this white triangle. The CPU will fit
only in the correct orientation.

6

TF520 A2+/TF560 A2+

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN1. This completes the installation.

7

Motherboard Manual

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN1: CPU Fan Header

1

4

JSFAN1/JSFAN2: System Fan Headers

JSFAN1 JSFAN2

Pin

Assignment

1 Ground
2 +12V
3

FAN RPM r ate
sense

4 Smart Fan

Control (By Fan)

Pin Assignment

1 Ground
2 +12V
3

FAN RPM
rate sense

13

Note:

The JCFAN1, JSFAN1, and JSFAN2 support 4-pin and 3-pin head connector. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be co nnected to pin#2, and the black wire is Ground and should be connected to
GND.

8

TF520 A2+/TF560 A2+

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMA1

DIMMB1

DIMMB2

DIMMA2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

B. Memory Capacity

DIMM Socket

Location

DIMMA1 256MB/512MB/1GB/2GB
DIMMB1 256MB/512MB/1GB/2GB
DIMMA2 256MB/512MB/1GB/2GB
DIMMB2 256MB/512MB/1GB/2GB

DDR2 Module

Total Memory

Size

Max is 8GB.

9

Motherboard Manual

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:

Install memory module of the same density in pairs, shown in the following
table.

Duual Channel Status

Enabled O O X X

Enabled X X O O

Enabled O O O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

DIMMA1 DIMMB1 DIMMA2 DIMMB2

10

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.

IDE1: Hard Disk Connectors

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.

34 33

TF520 A2+/TF560 A2+

12

3940

21

11

Motherboard Manual

PEX16-1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

PEX1_1/PEX1_2: PCI-Express x1 Slots

- PCI-Express 1.0a compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX1_1

PEX1_2

PCI1~PCI3: Peripheral Component Interconnect Slots

This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PEX16_1

12

PCI 1

PCI2

PCI3

TF520 A2+/TF560 A2+

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep
button and speaker connection. It allows user to connect the PC case’s front
panel switch functions.

PWR_LED

SLP

9
1

SPK

++

On/Off

-

-

+

HLED

16
8

RST

Pin Assignment Function Pin Assignment Function

1 +5V 9 Sleep control
2 N/A 10 Ground
3 N/ A 1 1 N/ A N/A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

Sleep button

Power LED

Power-on button

13

Motherboard Manual

JATXPW R1: AT X Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

12

Pin Assignment

1 +3.3V
2 +3.3V
3 Ground
4 +5V
5 Ground
6 +5V

24

1

13

7 Ground
8 PW_OK

9 Standby Voltage +5V
10 +12V
11 +12V
12 +3.3V
13 +3.3V
14 -12V
15 Ground
16 PS-ON
17 Ground
18 Ground
19 Ground
20 NC
21 +5V

22 +5V
23 +5V
24 Ground

JATXPW R2: AT X Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

14

23

4

1

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

TF520 A2+/TF560 A2+

JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Assignment

Pin

1 +5V (fused)

2910

1

2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 Key

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. It will disable the output on back panel audio connectors.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in

2

10

1

9

4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10 Jack Sense

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

Pin

1 Left Channel

1

4

Input
2 Ground
3 Ground
4 Right Channel

Input

15

Motherboard Manual

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

SATA1

SATA3

SATA2 SATA4

7

4

1

Assignment

Pin

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

3

1

Pin 1-2 Close:

Normal Operation
(default).

16

13

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

3

1

Pin 2-3 Close:

Clear CMOS data.

JSPDIF_OUT1: Digital Audio out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

2

TF520 A2+/TF560 A2+

Pin

Assignment

1 +5V
2 SPDIF_OUT

3

1

3 Ground

1

25

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

17

Motherboard Manual

JATXPWR3: Auxiliary Power for Graphics

This connector is an auxiliary power connection for graphics cards. Exclusive
power for the graphics card provides better graphics performance.

On-Board LED Indicators

There are 2 LED indicators on the motherboard to show system status.

Pin

Assignment

1

4

1 +12V
2 Ground
3 Ground
4 VCC

18

LED_D1

LED_D2

LED_D1 and LED_D2:

These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:

LED_D1 LED_D2 Message

ON ON Norma l

ON OFF Memory Error
OFF ON VGA Error
OFF OFF Abnormal: CPU / Chipset error.

On-Board Buttons

There are 2 on-board buttons.

TF520 A2+/TF560 A2+

PWRSW1RSTSW1

PWRSW1:

This is an on-board Power Switch button.

RSTSW1:

This is an on-board Reset button.

19

Motherboard Manual

CHAPTER 4: NVIDIA RAID FUNCTIONS

4.1 O

z Supports Windows XP Home/Professional Edition, and Windows 2000 Professional.

PERATION SYSTEM

4.2 RAID ARRAYS

NVRAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 0+1: RAID 0+1 combines the techniques used in R AID 0 and RAID 1.

RAID 5: RAID 5 provides fault to lerance and better utilizat ion of disk capacity.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large f i le into sma ller blocks an d pe rforms d isk r ead s and writes acr oss multip le
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

 Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the

platform.

 Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

 Benefits: provides increased data throughput, especially for large files. No

capacity loss penalty for parity.

 Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

 Fault Tolerance: No.

20

Blo ck 1
Block 3
Block 5

Block 2
Block 4
Block 6

TF520 A2+/TF560 A2+

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliab le
media.

Features and Benefits

 Drives: Minimum 2, and maximum is 2.
 Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

 Benefits: Provides 100% data redundancy. Should one drive fail, the

controller switches to the other drive.

 Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

 Fault Tolerance: Yes.

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

21

Motherboard Manual

RAID 0+1:

RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1
solution for improved performance plus resiliency.

Features and Benefits

 Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
 Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.

 Drawbacks: Requires twice the available disk space for data redundancy,

the same as RAID level 1.

 Fault Tolerance: Yes.

22

Bloc k 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

TF520 A2+/TF560 A2+

RAID 5:

RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained by
ensuring that the parity information for any given block of data is placed on a different
drive from those used to store the data itself.

Features and Benefits

 Drives: Mini mu m 3.
 Uses: RAID 5 is recommended for transaction processing and general

purpose service.

 Benefits: An ideal combination of good performance, good fault tolerance,

and high capacity and storage efficiency.

 Drawbacks: Individual block data transfer rate same as a single disk. Write

performance can be CPU intensive.

 Fault Tolerance: Yes.

Disk 1

DATA 1

DATA 3

PARITY

DATA 7
DATA 9

PARITY

Disk 2

DATA 2

PARIT Y

DATA 5

DATA 8
PARIT Y
DATA 11

Disk 3

PARIT Y

DATA 4

DATA 6

PARIT Y

DATA 10
DATA 12

※ For more detailed setup information, please refer to the Driver CD, or go to

http://www.nvidia.com/page/pg_20011106217193.html to download NVIDIA nForce Tutorial Flash.

23

Motherboard Manual

CHAPTER 5: OVERCLOCK QUICK GUIDE

5.1 T-P

Biostar T-Power is a whole new utility that is desig ned for overclock users.
Based on many precise tests, Biostar Engineering Team (BET) has
developed this ultimate overclock engine to raise system performance.
No matter whether under BIOS or Windows interface, T-Power is able to
present the best system state according to users’ overclock setting.

T-Power BIOS Features:

T-Power Windows Feature:

OWER INTRODUCTION

Overclocking Navigator Engine (O.N.E.)

CMOS Reloading Program (C.R.P.)

Memory Integration Test (M.I.T., under Overclock Navigator Engine)

Integrated Flash Program (I.F.P.)

Self Recovery System (S.R.S)

Smart Fan Function (under PC Health Status)

Hardware Monitor

Overclock Engine

System Infor mation

24

!! WARNING !!

For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.

TF520 A2+/TF560 A2+

5.2 T-POWER BIOS FEATURE

A. Overclocking Navigator Engine (O.N.E.):

ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.

Manual Overclock System (M.O.S.)

MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.

25

Motherboard Manual

DRAM Configuration:

Enter this function for more advanced DRAM settings.

CPU Frequency:

CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.

K8<->NB HT Spee d:

This option controls the HyperTransport speed of CPU to northbridge
chipset.

K8<->NB HT Width:

This option controls the HyperTransport width of CPU to northbridge
chipset.

PCIE Spread Spectrum:

This BIOS feature allows you to reduce the EMI of the PCI Express bus by
modulating the signals it generates so that the spikes are reduced to flatter
curves. Please disable this option when proceeding overclocking.

HT Spread Spectrum:

Please disable this option when proceeding overclocking.

PCIE Clock:

It helps to increase VGA card performance.

CPU Voltage:

This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.

26

NPT Fid Contro l:

This function allows you to adjust the frequency ratio of CPU.

Chipset Voltage:

This function will increase chipset stability when overclocking.

Memory Voltage :

This function will increase memory stability when overclocking.

TF520 A2+/TF560 A2+

Automatic Overclock System (A.O.S.)

For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.

Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.

V6 Tech Engine:

This setting will raise about 10%~15% of whole system performance.

V8 Tech Engine:

This setting will raise about 15%~25% of whole system performance.

27

Motherboard Manual

V12 Tech Engine:

This setting will raise about 25%~30% of whole system performance.

Notices:

1. Not all types of AMD CPU perform above overclock setting ideally; the difference will be based
on the selected CPU model.

B. CMOS Reloading Program (C.R.P.):

It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations.
Moreover, users are able to save an ideal overclock setting during overclock
operation.
There are 50 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.

28

TF520 A2+/TF560 A2+

C. Memory Integration Test (M.I.T.):

This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or

software are needed.

Step 1:

The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.

↓

Step 2:

Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.

Step 3:

When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.

29

Motherboard Manual

D. Self Recovery System (S.R.S.):

This function can’t be seen under T-Power BIOS setup; and is always on
whenever the system starts up.

However, it can prevent system hang-up due to inappropriate overclock
actions.

When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.

E. Integrated Flash Program (I.F.P.):

IFP is a safe and quick way to upgrade BIOS.

Step 1:

Go to Biostar website (http://www.biostar.com.tw
file. Then, save the file into a floppy disk.

Step 2:

Insert the floppy disk and reboot the system to get into CMOS screen.

Step 3:

Select the item “Integrated Flash Program” to get the following frame and
choose the BIOS file downloaded in step 1.

) to download the latest BIOS

30

Step 4:

Press “Enter” key to start BIOS file loading, and BIOS updating will process
automatically.

Step 5:

When the BIOS update is completed, press YES to the message “Flash done,
Reset system”, and the system will reboot automatically to finish the process.

Advise:

You can update the system BIOS by simply pressing “Enter” key for three times.

TF520 A2+/TF560 A2+

F. Smart Fan Function:

Smart Fan Function is under “PC Health Status”.
This is a brilliant feature to control CPU Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by

CPU temperature.
This function will protect CPU from overheat problem and maintain the system

temperature at a safe level.

↓

SYS FAN1 Control by:

This option controls the northbridge fan. Select “Smart” to activate smart
fan function for reducing the noise and power consuming of the fan.

CPU FAN Control by:

This option controls the CPU fan. Select “Smart” to activate smart fan
function for reducing the noise and power consuming of the fan.

CPU Fan Off <℃>:

If the CPU temperature is lower than the set value, the CPU fan will turn
off. The range is from 0℃~127℃, with an interval of 1℃.

31

Motherboard Manual

CPU Fan Start <℃>

The CPU fan starts to work when CPU temperature arrives to this set
value. The range is from 0℃~127℃, with an interval of 1℃.

CPU Fan Full speed <℃ >

When CPU temperature arrives to the set value, the CPU fan will work
under Full Speed. The range is from 0℃~127℃, with an interval of 1℃.

Start PWM Value

When CPU temperature arrives to the set value, the CPU fan will work
under Smart Fan Function mode. The range is from 0~127, with an
interval of 1.

32

5.3 T-POWER WINDOWS FEATURE

1. Desktop Icon

After the T-Utility has been installed, a T-Utility icon will appe ar on the
desktop, just like the icon shown below.

Now you can launch the T-Utility simply by double-clicking the desktop
icon.

2. Main Panel

If you double-click the desktop icon, T-Utility will be launched. Please
refer to the following fig ure; the utility’s first window you will see is
Main Panel.

Main Panel contains features as follows:

a. Display the CPU Speed, CPU external clock, Memory clock, VGA

clock, and PCI clock information.

b. Contains About, Overclock/Overvoltage, and Hardware Monitor

Buttons for invoking respective panels. The On/Off button is for
closing the program.

TF520 A2+/TF560 A2+

33

Motherboard Manual

3. Overclock/Overvoltage Panel

Click the Overclock/Overvoltage button in the Main Panel, the button
will be highlighted and the Overclock/Overvoltage Panel will show
up as the following figure. As you can see, the Overclock Panel is
on the upper side, and the Overvoltage Panel is on the lower side.

34

TF520 A2+/TF560 A2+

Overclock Panel contains these features:

a. “Auto-Overclock”:

User can click this button and T-Utility will set the best and stable
performance and frequency automatically. A warning dialog as
below will show up to notify you that the system may become
unstable, click on “OK” to continue.

Then T-Utility will exec ute a series of testing until system fail.
Then system will do fail-safe reboot by using Watchdog function.
After reboot, launch the T-Utility again and the utility will load the
previously verified best and stable frequency.

b. “Verify”:

If you use the “Manual Adjust” bar to adjust the CPU frequency,
then you can click t his button and T-Utility will proceed a testing for
current frequency. If the testing is ok, then the current frequency
will be saved into system registry. If the testing fails, system will do
a fail-safe rebooting. After reboot, the T-Utility will restore to the
hardware default setting.

Warning:

Manually overclock is potentially dangerous, especially when the
overclocking percentage is over 110 %. We strongly recommend you
verify every speed you overclock by click the Verify button. Or, you can
just click Auto overclock button and let T-Utility automatically gets the
best result for you.

c. “V3 Engine”/“V6 Engine”/“V9 Engine”:

Provide user the ability to do real-time overclock adjustment.

d. “Recovery”:

Click t his button and the T-Utility will restore all values to the
hardware default setting.

35

Motherboard Manual

e. “Save / Open Setting”:

Click Save button to save current setting to a file, and click Open
button to load a previously saved setting.

f. “Panel Color”:

Click this button to change the color of the panel.

Overvoltage Panel contains these features:

a. “CPU Voltage”:

This function allows user to adjust CPU voltage. Click on “+” to
increase or “-“ to decrease the CPU voltage.

b. “Memory Voltage”:

This function allows user to adjust Memory voltage. Click on “+”
to increase or “-“ to decrease the Memory voltage.

c. “Chipset Voltage”:

This function allows user to adjust Chipset voltage. Click on “+”
to increase or “-“ to decrease the Chipset voltage.

4. Hardware Monitor Panel

Click the Hardware Monitor button in Main Panel, the button will be
highlighted a nd the Hardware Monitor panel will s how up as the
following figure.

In this panel, you can get the real-time status information of your
system. The information will be refreshed every 1 second.

36

TF520 A2+/TF560 A2+

5. About Panel

Click the “about” button in Main Panel, the button will be highlighted
and the About Pa nel will show up as the following fig ure.

In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the the version number of T-Utility.

Note:

Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, T-Utility divides these
features to separate panels. If one chipset is not on board, the
correlative button in Main panel will be disabled, but it will not
interfere with other panels’ functions. This property can make
T-Utility more robust.

37

Motherboard Manual

CHAPTER 6: USEFUL HELP

6.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

38

TF520 A2+/TF560 A2+

6.2 AWARD BIOS BEEP CODE

Beep Sound Meaning

One long beep followed by two short
beeps

High-low siren sound CPU overheated

One Short beep when system boot-up No error found during POST

Long beeps every other second No DRAM detected or install

Video card not found or video card
memory bad

System will shut down automatically

6.3 EXTRA INFORMATION

A. BIOS Update

After you fail to update BIOS or BIOS is invaded by virus, the
Boot-Block function will help to restore BIOS. If the following message
is shown after boot-up the system, it means the BIOS contents are
corrupted.

In this Case, please follow the procedure below to restore the BIOS:

1. Make a bootable floppy disk.

2. Download the Flash Utility “AWDFLASH.exe” from the Biostar
website: www.biostar.com.tw

3. Confirm motherboard model and download the respectively BIOS
from Biostar website.

4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.

5. Insert the bootable disk into floppy drive and press Enter.

6. System will boot-up to DOS prompt.

7. Type “Awdflash xxxx.bf/sn/py/r” in DOS prompt.
(xxxx means BIOS name.)

8. System will update BIOS automatically and restart.

9. The BIOS has been recovered and will work properly.

39

Motherboard Manual

B. CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdow n
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

40

6.4 TROUBLESHOOTING

Probable Solution

1. No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.

2. Indicator light on keyboard does
not turn on.

System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.

System does not boot from hard disk
drive, can be booted from optical drive.

System only boots from optical drive.
Hard disk can be read and applications
can be used but booting from hard disk
is impossible.

Screen message says “Invalid
Configuration” or “CMOS Failure.”

Cannot boot system after installing
second hard drive.

TF520 A2+/TF560 A2+

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

41

Motherboard Manual

APPENDENCIES: SPEC IN OTHER LANGUAGE

G

ERMAN

T F520 A2+ TF560 A2+

Sockel AM2 / AM2+(Durch BIOS Aktualisierung)

AMD Athlon 64 / Athlon 64 x2 / Sempron

CPU

FSB

Chipsatz nVIDIA nForce 520 nVIDIA nForce 560

Super E/A

Arbeitsspeich

er

IDE

SATA II

LAN

Prozessoren

Die AMD 64-Architektur unterstützt eine 32-Bit-

und 64-Bit-Datenverarbeitung

Unterstützt Hyper Transport und Cool’n’Quiet

Unterstützt HyperTransport mit einer Bandbreite

von bis zu 1 GHz

ITE 8716F

Biet et die h äufig ver wendeten a lten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehz ahl-Cont roller

"Smart Guardian"-Funktion von ITE

DDR2 DIMM-Steckplätze x 4

Jeder DIMM unterst ützt 256/512MB & 1GB/2GB

DDR2.

Max. 8GB Arbeitsspeicher

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533 / 667 / 800 registrierte

DIMMs. ECC DIMMs werden nicht unterstützt.

Int eg r iert er IDE-Co n t rolle r

Ultra DMA 33 / 66 / 100 / 133 Bus

Master-Modus Unterstützt PIO-Modus 0~4,

Integrierter Serial ATA-Controller

Datentransferrate b is zu 3Gb/s

Konform mit d er SATA-Spezifikation Version 2.0.

Realtek RTL 8110SC / RTL 8100C(opt ional)

10 / 100 / 1000 Mb/s Auto-Negotiation

(Gigabit-Bandbreite nur beim RTL 8110SC)

Halb-/ Vollduplex-Funktion

Sockel AM2 / AM2+(Durch BIOS Aktualisierung)

AMD Athlon 64 / Athlon 64 x2 / Sempron

Prozessoren

Die AMD 64-Architektur unterstützt eine 32-Bit-

und 64-Bit-Datenverarbeitung

Unterstützt Hyper Transport und Cool’n’Quiet

Unterstützt HyperTransport mit einer Bandbreite

von bis zu 1 GHz

ITE 8716F

Biet et die h äufig ver wendeten a lten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehz ahl-Cont roller

"Smart Guardian"-Funktion von ITE

DDR2 DIMM-Steckplätze x 4

Jeder DIMM unterst ützt 256/512MB & 1GB/2GB

DDR2.

Max. 8GB Arbeitsspeicher

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533 / 667 / 800 registrierte

DIMMs. ECC DIMMs werden nicht unterstützt.

Int eg r iert er IDE-Co n t rolle r

Ultra DMA 33 / 66 / 100 / 133 Bus

Master-Modus Unterstützt PIO-Modus 0~4,

Integrierter Serial ATA-Controller

Datentransferrate b is zu 3Gb/s

Konform mit d er SATA-Spezifikation Version 2.0.

Realtek RTL 8110SC / RTL 8100C(opt ional)

10 / 100 / 1000 Mb/s Auto-Negotiation

(Gigabit-Bandbreite nur beim RTL 8110SC)

Halb-/ Vollduplex-Funktion

42

TF520 A2+/TF560 A2+

T F520 A2+ TF560 A2+

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1-Kanal-Audioausgabe (ALC888)

5.1-Kanal-Audioausgabe (ALC662)

Unterstützt High-Definition Audio

PS/2-Tastatur x1

PS/2- Maus x1

Serieller Anschluss x1

LAN-Anschluss x1

USB-Anschluss x6

Audioanschluss (Ver 5.x) x6

Audioanschluss (Ver 6.x) x3

NVIDIA nTunes

Unterstützt RAID 0 / 1 / 0+1 / 5

Windows 2K / XP / V ISTA

Biostar behält sich das Recht vor, ohne

Ankündigung die Unterstützung für ein

Betriebssystem hinzuzufügen oder zu

entfern en.

Audio-Codec

Steckplätze

Onboard-Ans

chluss

Rückseiten-E

/A

Platinengröße

.

Sonderfunkti

onen

OS-Unterstüt

zung

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1-Kanal-Audioausgabe (ALC888)

5.1-Kanal-Audioausgabe (ALC662)

Unterstützt High-Definition Audio

PCI-Steckplat z x3 PCI-Steckplat z x3

PCI Express x16 Steckplatz x1 PCI Express x16 Steckplatz x1

PCI Express x 1-Steckplatz x2 PCI Express x 1-Steckplatz x2

Diskettenlaufwerkanschluss x1 Diskettenlaufwerkanschluss x1

Druckeranschluss Anschluss x1 Druckeranschluss Anschluss x1

IDE-Anschluss x1 IDE-Anschluss x1

SATA-Anschluss x4 SATA-Anschluss x4

Fronttafelanschluss x1 Fronttafelanschluss x1

Front-Audioanschluss x1 Front-Audioanschluss x1

CD-IN-Anschluss x1 CD-IN-Anschluss x1

S/PDIF-Ausgangsanschluss x1 S/PDIF-Ausgangsanschluss x1

CPU-Lüfter-Sockel x1 CPU-Lüfter-Sockel x1

System-Lüfter-Sockel x2 System-Lüfter-Sockel x2

"CMOS löschen "-So cke l x1 "C MOS löschen "- Sockel x 1

USB-Anschluss x2 USB-Anschluss x2

Stromanschluss (24-polig) x1 Stromanschluss (24-polig) x1

St r oman s chluss (4-pol ig ) x2 St romans ch luss (4-polig ) x2

PS/2-Tastatur x1

PS/2- Maus x1

Serieller Anschluss x1

LAN-Anschluss x1

USB-Anschluss x6

Audioanschluss (Ver 5.x) x6

Audioanschluss (Ver 6.x) x3

244 mm (B) X 305 mm (L) 244 mm (B) X 305 mm (L)

NVIDIA nTunes

Unterstützt RAID 0 / 1 / 0+1

Windows 2K / XP / V ISTA

Biostar behält sich das Recht vor, ohne

Ankündigung die Unterstützung für ein

Betriebssystem hinzuzufügen oder zu

entfern en.

43

Motherboard Manual

FRANCE

TF520 A2+ TF560 A2+

Socket AM2 / AM2+ (Par la mise à jour de BIOS)
Processeurs AMD Athlon 64 / Athlon 64 x2 /

UC

Bus frontal

Chipset nVIDIA nForce 520 nVIDIA nForce 560

Super E/S

Mémoire
principale

IDE

SATA
SATA II

LAN

Sempron
L'architecture AMD 64 permet le calcul 32 et 64
bits
Prend en charge Hyper Transport et Cool’n’Qu iet

Prend en charge Hyper Transport jusqu'à une

bande passante de 1 GHz

ITE 8716F
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.

Int e rface à f aib le co mpte de b roches
Initiatives de contrôle environnementales,
Mon iteur d e mat ér iel
Contrôleur de vitesse de ventilateur
Fonction "Gardien intelligent" de l'ITE

Fentes DDR2 DIM M x 4
Chaque DIMM prend en charge des DDR2 de
256/512 Mo et 1Go/2Go
Capacité mé mo ire max ima le de 8 Go
Module de mémoire DDR2 à mode à double voie

Prend en charge la DDR2 533 / 667 / 800
Les DIMM à registres et DIMM avec code
correcteurs d'err eurs ne s ont pas prises en
charg e

Contrôleur IDE intégré

Mode principale de Bus Ultra DMA 33 / 66 / 100 /
133
Prend en charge le mode PIO 0~4,

Contrô leur Serial ATA int é g r é :
Taux de transfert jusqu'à 3 Go/s.

Co nforme à l a s p écificat ion SATA Ver s ion 2.0

Realtek RTL 8110SC / RTL 8100C(opt ional)
10 / 100 / 1000 Mb/s négociation automatique
(La bande passante Gigabit est pour le RTL
8110SC uniquement)

Half / Full duplex capability

Socket AM2 / AM2+ (Par la mise à jour de BIOS)
Processeurs AMD Athlon 64 / Athlon 64 x2 /

Sempron
L'architecture AMD 64 permet le calcul 32 et 64
bits
Prend en charge Hyper Transport et Cool’n’Qu iet

Prend en charge Hyper Transport jusqu'à une

bande passante de 1 GHz

ITE 8716F
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.

Int e rface à f aib le co mpte de b roches
Initiatives de contrôle environnementales,
Mon iteur d e mat ér iel
Contrôleur de vitesse de ventilateur
Fonction "Gardien intelligent" de l'ITE

Fentes DDR2 DIM M x 4
Chaque DIMM prend en charge des DDR2 de
256/512 Mo et 1Go/2Go
Capacité mé mo ire max ima le de 8 Go
Module de mémoire DDR2 à mode à double voie

Prend en charge la DDR2 533 / 667 / 800
Les DIMM à registres et DIMM avec code
correcteurs d'err eurs ne s ont pas prises en
charg e

Contrôleur IDE intégré

Mode principale de Bus Ultra DMA 33 / 66 / 100 /
133
Prend en charge le mode PIO 0~4,

Contrô leur Serial ATA int é g r é :
Taux de transfert jusqu'à 3 Go/s.

Co nforme à l a s p écificat ion SATA Ver s ion 2.0

Realtek RTL 8110SC / RTL 8100C(opt ional)
10 / 100 / 1000 Mb/s négociation automatique
(La bande passante Gigabit est pour le RTL
8110SC uniquement)

Half / Full duplex capability

44

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

Codec audio

Connecteur
embarqu é

E/S du

panneau
arrière

Dimensions
de la carte

Fonctionnali
tés

spéciales

Support SE

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Sortie audio à 7.1 voies (ALC888)
Sortie audio à 5.1 voies (ALC662)
Prise en ch arg e de l'audio haut e déf in it ion Sort ie

Fente PCI x3 Fente PCI x3
Slot PCI Express x16 x1 Slot PCI Express x16 x1 Fentes
Slot PCI Express x 1 x2 Slot PCI Express x 1 x2

Connecteur de disquette x1 Connecteur de d isquette x1
Connecteur de Port d'imprimante x1 Connecteur de Port d'imprimante x1

Connecteur IDE x1 Connecteur IDE x1
Connecteur SATA x4 Connecteur SATA x4
Connecteur du panneau avant x1 Connecteur du panneau avant x1
Connecteur Audio du panneau avant x1 Connecteur Audio du panneau avant x1
Connecteur d'entrée CD x 1 Connecteur d' entrée CD x 1

Connecteur de sortie S/PDIF x1 Connecteur d e sortie S/PDIF x1
Embase de ventilateur UC x1 Embase de ventilateur UC x1
Embase de ventilateur système x2 Embase de ventilateur système x2
Embase d'effacement CMOS x1 Embase d'effacement CMOS x1
Connecteur USB x2 Connecteur USB x2

Connecteur d'aliment at ion x 1
(24 broches)
Connecteur d'aliment at ion x 2
(4 broch es )

Clavier PS/2 x1

Souris PS/2 x1
Port série x1
Port LAN x1
Port US B x6
Fiche audio (Ver 5.x) x6

Fiche audio (Ver 6.x) x3

244 mm (l) X 305 mm (H) 244 mm (l) X 305 mm (H)

NVIDIA nTunes
Prise en charg e RAID 0 / 1 / 0 +1

Windows 2K / XP / V ISTA
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis.

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Sortie audio à 7.1 voies (ALC888)
Sortie audio à 5.1 voies (ALC662)
Prise en ch arg e de l'audio haut e déf in it ion Sort ie

Connecteur d'aliment at ion x 1
(24 broches)
Connecteur d'aliment at ion x 2
(4 broch es )

Clavier PS/2 x1

Souris PS/2 x1
Port série x1
Port LAN x1
Port US B x6
Fiche audio (Ver 5.x) x6

Fiche audio (Ver 6.x) x3

NVIDIA nTunes
Prise en charge RAID 0 / 1 / 0+1 / 5

Windows 2K / XP / V ISTA
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis.

45

Motherboard Manual

ITALIAN

TF520 A2+ TF560 A2+

Socket AM2 / AM2+(Dall'aggiornamento di
BIOS)
Processori AMD Athlon 64 / Athlon 64 x2 /

CPU

FSB

Chipset nVIDIA nForce 520 nVIDIA nForce 560

Super I/O

Memoria
principale

IDE

SATA II

LAN

Sempron
L’archit ett u ra AMD 64 abilita la
computazione 32 e 64 bit
Supporto di Hyper Transport e Cool’n’Quiet

Supporto di HyperTransport fino a 1 GHz di
larghezza di banda

ITE 8716F
Fo rnis ce le funzionalit à lega cy S uper I/O
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co ntroller velo c it à ventolin a
Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2 256/512MB e
1GB/2GB
Capacità massima della memoria 8GB
Modulo di memoria DDR2 a canale doppio
Supporto di DDR2 533 / 667 / 800
DIMM r egistrati e DIMM ECC non sono
supportati

Co n troller IDE int eg rat o
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
Supporto modalità PIO Mode 0-4

Co ntroller Ser ia l ATA in t eg rat o
Velocità di trasferimento dei dati fino a 3
Gb/s.
Co mp at ib ile s p ec ifiche S ATA Versione 2.0.

Realtek RTL 8110SC / RTL 8100C(opt ional)
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo
per RTL 8110SC)
Capacità Half / Full Dup lex

Socket AM2 / AM2+(Dall'aggiornamento di
BIOS)
Processori AMD Athlon 64 / Athlon 64 x2 /
Sempron
L’archit ett u ra AMD 64 abilita la
computazione 32 e 64 bit
Supporto di Hyper Transport e Cool’n’Quiet

Supporto di HyperTransport fino a 1 GHz di
larghezza di banda

ITE 8716F
Fo rnis ce le funzionalit à lega cy S uper I/O
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co ntroller velo c it à ventolin a
Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2 256/512MB e
1GB/2GB
Capacità massima della memoria 8GB
Modulo di memoria DDR2 a canale doppio
Supporto di DDR2 533 / 667 / 800
DIMM r egistrati e DIMM ECC non sono
supportati

Co n troller IDE int eg rat o
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
Supporto modalità PIO Mode 0-4

Co ntroller Ser ia l ATA in t eg rat o
Velocità di trasferimento dei dati fino a 3
Gb/s.
Co mp at ib ile s p ec ifiche S ATA Versione 2.0.

Realtek RTL 8110SC / RTL 8100C(opt ional)
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo
per RTL 8110SC)
Capacità Half / Full Dup lex

46

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

Codec
audio

Allo g g i

Connettori
su scheda

I/O
pannello
posteriore

Dimension
i scheda
Caratterist
iche
speciali

Sistemi
operativi
supportati

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Uscita audio 7.1 canali (ALC888)
Uscita audio 5.1 canali (ALC662)
Supporto audio High-Definition (HD)
Allo g g io PC I x3 Allo g gio PC I x3
Alloggio PCI Express x16 x1 Alloggio PCI Express x16 x1
Alloggio PCI Express x1 x2 Alloggio PCI Express x1 x2
Connettore floppy x1 Connettore floppy x1
Connettore Porta stampante x1 Connettore Porta stampante x1
Connettore IDE x1 Connettore IDE x1
Connettore SATA x4 C onnettore SATA x4
Connettore pannello frontale x1 Connettore pannello frontale x1
Connettore audio frontale x1 Connettore audio frontale x1
Connettore CD-in x1 Connettore CD-in x1
Connettore output SPDIF x1 Connettore output SPDIF x1
Co lletto r e ventolina C PU x 1 Collet t o re vent o lina C PU x1
Co lletto r e ventolina sistema x 2 Co llet t o re vent o lin a s is t ema x 2
Co lletto r e cance llaz ione CMOS x1 Co llett o re cance llaz ione CMOS x1
Connettore USB x2 Connettore USB x2
Connettore alimentaz ione x 1
(24 pin)
Connettore alimentaz ione x2
(4 pin)
Tas t ie r a PS / 2 x 1
Mou s e PS/2 x1
Porta seriale x1
Porta LAN x1
Porta USB x6
Connettore audio (Ver 5.x) x6
Connettore audio (Ver 6.x) x3

244 mm (larghezza) x 305 mm (altezza) 244 mm (larghezza) x 305 mm (altezza)

nTunes NVIDIA
Supporto RAID 0 / 1 / 0+1

Windows 2K / XP / VISTA
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Uscita audio 7.1 canali (ALC888)
Uscita audio 5.1 canali (ALC662)
Supporto audio High-Definition (HD)

Connettore alimentaz ione x 1
(24 pin)
Connettore alimentaz ione x2
(4 pin)
Tas t ie r a PS / 2 x 1
Mou s e PS/2 x1
Porta seriale x1
Porta LAN x1
Porta USB x6
Connettore audio (Ver 5.x) x6
Connettore audio (Ver 6.x) x3

nTunes NVIDIA
Supporto RAID 0 / 1 / 0+1 / 5

Windows 2K / XP / VISTA
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.

47

Motherboard Manual

SPANISH

TF520 A2+ TF560 A2+

Conector AM2 / AM2+ (Por BIOS actualiza)

Procesadores AMD Athlon 64 / Athlon 64 x2 /

Sempron

La arquitectura AMD 64 permite el procesado de

32 y 64 bits

Soporta las tecnologías Hyper Transport y

Cool’n’Quiet

Admite HyperTransport con un ancho de banda

de hasta 1 GHz

ITE 8716F

Le ofrece las funcionalidades heredadas de uso

más común Súper E/S.

Interfaz de cuenta Low Pin

In iciat ivas d e cont rol d e entorno,

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

Ranuras DIMM DDR2 x 4

Cada DIMM admite DDR de 256/512MB y

1GB/2GB

Capacidad máxima de memoria de 8GB

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533 / 667 / 800

No admite DIMM registrados o DIMM

comp atib les con ECC

Controlador IDE integrado

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible co n la ve rsión S ATA 2 .0.

Realtek RTL 8110SC / RTL 8100C (opcional)

Negociación de 10 / 100 / 1000 Mb/s (el ancho

de banda Gigabit es únicamente para 8110SC)

Funciones Half / Full dúplex

CPU

FSB

Conjunto de

chips

Súper E/S

Memoria

principal

IDE

SATA II

Red Local

Conector AM2 / AM2+ (Por BIOS actualiza)

Procesadores AMD Athlon 64 / Athlon 64 x2 /

Sempron

La arquitectura AMD 64 permite el procesado de

32 y 64 bits

Soporta las tecnologías Hyper Transport y

Cool’n’Quiet

Admite HyperTransport con un ancho de banda

de hasta 1 GHz

nVIDIA nForce 520 nVIDIA nForce 560

ITE 8716F

Le ofrece las funcionalidades heredadas de uso

más común Súper E/S.

Interfaz de cuenta Low Pin

In iciat ivas d e cont rol d e entorno,

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

Ranuras DIMM DDR2 x 4

Cada DIMM admite DDR de 256/512MB y

1GB/2GB

Capacidad máxima de memoria de 8GB

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533 / 667 / 800

No admite DIMM registrados o DIMM

comp atib les con ECC

Controlador IDE integrado

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible co n la ve rsión S ATA 2 .0.

Realtek RTL 8110SC / RTL 8100C (opcional)

Negociación de 10 / 100 / 1000 Mb/s (el ancho

de banda Gigabit es únicamente para 8110SC)

Funciones Half / Full dúplex

48

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

Códecs de
sonido

Ranuras

Conectores
en p laca

Panel
trasero de
E/S

Ta maño d e
la placa

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Salida de sonido de 7.1 canales (ALC888)
Salida de sonido de 5.1 canales (ALC662)
Soporte de sonido de Alta Definición

Ranura PCI X3 Ranura PCI X3
Ranura PCI Express x16 X1 Ranura PCI Express x16 X1
Ranura PCI express x 1 X2 Ranura PCI express x 1 X2

Conector disco flexible X1 Conector disco flexible X1
Conector Puerto de impresora X1 Conector Puerto de impresora X1
Conector IDE X1 Conector IDE X1
Conector SATA X4 Conector SATA X4
Conector de panel frontal X1 Conector de panel frontal X1
Conector de sonido frontal X1 Conector de sonido frontal X1
Conector de entrada de CD X1 Conector de entrada de CD X1
Conector de salida S/PDIF X1 Conector de salida S/PDIF X1
Cabecera de ventilador de CPU X1 Cabecera de ventilador de CPU X1
Cabecera de ventilador de sistema X2 Cabecera de ventilador de sistema X2
Cabecera de borrado de CMOS X1 Cabecera de borrado de CMOS X1
Conector USB X2 Conector USB X2
Conector de alimentación X1
(24 patillas)
Conector de alimentación X2
(4 patillas)

Tec lad o P S /2 X1
Ratón PS/2 X1
Puert o serie X1
Puerto de red local X1
Puert o USB X6
Conector de sonido (Ver 5.x) X6
Conector de sonido (Ver 6.x) X3

244 mm. (A) X 305 Mm. (H) 244 mm. (A) X 305 Mm. (H)

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Salida de sonido de 7.1 canales (ALC888)
Salida de sonido de 5.1 canales (ALC662)
Soporte de sonido de Alta Definición

Conector de alimentación X1
(24 patillas)
Conector de alimentación X2
(4 patillas)

Tec lad o P S /2 X1
Ratón PS/2 X1
Puert o serie X1
Puerto de red local X1
Puert o USB X6
Conector de sonido (Ver 5.x) X6
Conector de sonido (Ver 6.x) X3

Funciones
especiales

Soporte de
sistema
operativo

NVIDIA nTunes
Admite RAID 0 / 1 / 0+1

Windows 2K / XP / V ISTA
Biostar se reserva el derecho de añadir o retirar
el soporte de cualquier SO con o s in aviso previo.

NVIDIA nTunes
Admite RAID 0 / 1 / 0+1 / 5

Windows 2K / XP / V ISTA
Biostar se reserva el derecho de añadir o retirar
el soporte de cualquier SO con o s in aviso previo.

49

Motherboard Manual

PORTUGUESE

TF520 A2+ TF560 A2+

Socket AM2 / AM2+ (Por B IOS atu alize)
Processadores AMD Athlon 64 / Athlon 64 x2 /
Sempron

CPU

FSB

Chipset nVIDIA nForce 520 nVIDIA nForce 560

Especificaçã
o Super I/O

Memória
principal

IDE

SATA II

LAN

A arq uite ctura A MD 64 p erm ite uma compu taç ão
de 32 e 64 bits
Suporta as tecno log ias H yper Transpo rt e
Cool’n’Quiet

Suporta a tecnologia HyperTransport com uma
largura d e banda at é 1 GHz

ITE 8716F
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
Interface LPC (Low Pin Count).
In iciat ivas p ara con t ro lo d o a mb ient e
Monitorização do hardware
Controlador da velocidade da ventoinha
Função "S mart Gu ardian" d a ITE

Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
DDR2 de 256/512 MB & 1 GB/2 GB
Capacidad e máx ima de me mória: 8 GB
Módulo de memória DDR2 de canal duplo
Suporta módulos DDR2 533 / 667 / 800
Os módulos DIMM registados e os DIMM ECC
não são suportados

Controlador IDE integrado
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,

Controlador Serial ATA integrado
Velocidades de transmissão de dados até 3 Gb/s.
Co mpat ib ilidad e co m a es pecifica ção S ATA
versão 2.0 .

Realtek RTL 8110SC / RTL 8100C(opcional)

Auto negociação de 10 / 100 / 1000 Mb/s (a

largura de banda Gigabit refere-se apenas à
especificação RTL 8110SC)

Capacidade semi/full-duplex

Socket AM2 / AM2+ (Por B IOS atu alize)
Processadores AMD Athlon 64 / Athlon 64 x2 /
Sempron
A arq uite ctura A MD 64 p erm ite uma compu taç ão
de 32 e 64 bits
Suporta as tecno log ias H yper Transpo rt e
Cool’n’Quiet

Suporta a tecnologia HyperTransport com uma
largura d e banda at é 1 GHz

ITE 8716F
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
Interface LPC (Low Pin Count).
In iciat ivas p ara con t ro lo d o a mb ient e
Monitorização do hardware
Controlador da velocidade da ventoinha
Função "S mart Gu ardian" d a ITE

Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
DDR2 de 256/512 MB & 1 GB/2 GB
Capacidad e máx ima de me mória: 8 GB
Módulo de memória DDR2 de canal duplo
Suporta módulos DDR2 533 / 667 / 800
Os módulos DIMM registados e os DIMM ECC
não são suportados

Controlador IDE integrado
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,

Controlador Serial ATA integrado
Velocidades de transmissão de dados até 3 Gb/s.
Co mpat ib ilidad e co m a es pecifica ção S ATA
versão 2.0 .

Realtek RTL 8110SC / RTL 8100C(opcional)

Auto negociação de 10 / 100 / 1000 Mb/s (a

largura de banda Gigabit refere-se apenas à
especificação RTL 8110SC)

Capacidade semi/full-duplex

50

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

Codec de
som

Ranhuras

Conectores
na placa

Entradas/S
aídas no
painel
traseiro

Tamanho
da placa
Característi
cas
especiais

Sistemas
operativos
suportados

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Saída de áudio de 7.1 canais (ALC888 )
Saída de áudio de 5.1 canais (ALC662 )
Suporta a especificação High-Definition Audio
Ranhura PCI x3 Ranhura PCI x3
Ranhura PCI Express x16 x1 Ranhura PCI Express x16 x1
Ranhura PCI Express x 1 x2 Ranhura PCI Express x 1 x2
Conector da unidade de disquetes x1 Conector da unidade de disquetes x1
Conector da para impressora x1 Conector da para impressora x1
Conector IDE x1 Conector IDE x1
Conector SATA x4 Conector SATA x4
Conector do painel frontal x1 Conector do painel frontal x1
Conector de áudio frontal x1 Conector de áudio frontal x1
Conector par a ent r ada d e CDs x 1 Conecto r para entrada d e CDs x1
Conector de saída S/PDIF x1 Conector de saída S/PDIF x1
Conector da ventoinha da CPU x1 Conector da vento inha da CPU x1
Conector da ventoinha do sistema x2 Conector da ventoinha do s istema x2
Conector para limpeza do CMOS x1 Conector para limpeza do CMOS x1
Conector USB x2 Conector USB x2
Conector de alimentação x1
(24 pinos)
Conector de alimentação x2
(4 p inos)
Tec lad o P S /2 x1
Rato PS/2 x1
Porta s ér ie x1
Porta LAN x1
Porta USB x6
Tomada de áudio (Ver 5.x) x6
Tomada de áudio (Ver 6.x) x3

244mm (L) X 305 mm (A) 244 mm (L) X 305 mm (A)

nTunes da NVIDIA
Suporta as funções RA ID 0 / 1 / 0+1

Windows 2K / XP / V ISTA
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)
Saída de áudio de 7.1 canais (ALC888 )
Saída de áudio de 5.1 canais (ALC662 )
Suporta a especificação High-Definition Audio

Conector de alimentação x1
(24 pinos)
Conector de alimentação x2
(4 p inos)
Tec lad o P S /2 x1
Rato PS/2 x1
Porta s ér ie x1
Porta LAN x1
Porta USB x6
Tomada de áudio (Ver 5.x) x6
Tomada de áudio (Ver 6.x) x3

nTunes da NVIDIA
Suporta as funções RA ID 0 / 1 / 0+1 / 5

Windows 2K / XP / V ISTA
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.

51

Motherboard Manual

POLISH

TF520 A2+ TF560 A2+

Socket AM2 / AM2+ (Przez BIOS modernizować)

AMD Athlon 64 / Athlon 64 x2 / Sempron

Procesor

FSB

Chipset nVIDIA nForce 520 nVIDIA nForce 560

Pamięć

główna

Super I/O

IDE

SATA II

LAN

Procesory

Architektura AMD 64 umożliwia przetwarzanie

32 i 64 bitowe

Obsługa Hyper Transport oraz Cool’n’Quiet

Obsługa HyperTransport o szerokości pasma do

1 GHz

Gniazda DDR2 DIMM x 4

Każde gniazdo DIMM obs ługuje moduły

256/512MB oraz 1GB/2GB DDR2

Maks. wielkość pamięci 8GB

Mod uł pamięci DDR2 z trybem podwójnego

kana łu

Obsługa DDR2 533 / 667 / 800

Brak obsług i Register ed DIMM oraz ECC D IMM

ITE 8716F

Zapewnia najbardziej powszechne funkcje Super

I/O.

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler prędkości wenty lato ra

Funkcja ITE "Smart Guardian"

Zintegrowany kontroler IDE

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

Zintegrowany kontroler Serial ATA

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersj i 2. 0.

Realtek RTL 8110SC / RTL 8100C (opcja)

10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją

szybkości (Pasmo gigabitowe wyłączn ie dla RTL

8110SC)

Działanie w tryb ie połowicznego / pełnego

dupleksu

Socket AM2 / AM2+ (Przez BIOS modernizować)

AMD Athlon 64 / Athlon 64 x2 / Sempron

Procesory

Architektura AMD 64 umożliwia przetwarzanie

32 i 64 bitowe

Obsługa Hyper Transport oraz Cool’n’Quiet

Obsługa HyperTransport o szerokości pasma do

1 GHz

Gniazda DDR2 DIMM x 4

Każde gniazdo DIMM obs ługuje moduły

256/512MB oraz 1GB/2GB DDR2

Maks. wielkość pamięci 8GB

Mod uł pamięci DDR2 z trybem podwójnego

kana łu

Obsługa DDR2 533 / 667 / 800

Brak obsług i Register ed DIMM oraz ECC D IMM

ITE 8716F

Zapewnia najbardziej powszechne funkcje Super

I/O.

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler prędkości wenty lato ra

Funkcja ITE "Smart Guardian"

Zintegrowany kontroler IDE

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

Zintegrowany kontroler Serial ATA

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersj i 2. 0.

Realtek RTL 8110SC / RTL 8100C (opcja)

10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją

szybkości (Pasmo gigabitowe wyłączn ie dla RTL

8110SC)

Działanie w tryb ie połowicznego / pełnego

dupleksu

52

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1 kanałowe wyjście aud io (ALC888 )

5.1 kanałowe wyjście aud io (ALC662 )

Obsługa H ig h-Def in it io n Aud io

Złącze główkowe kasowan ia

CMOS x1

Klawiatura PS/2 x1

Mys z PS /2 x 1

Port szeregowy x1

Port LAN x1

Port US B x6

Gniazdo audio (Ver 5.x) x6

Gniazdo audio (Ver 6.x) x3

Kodek

dźwiękowy

Gniazda

Złącza

wbud owane

Back Panel

I/O

Wymiary

płyty

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1 kanałowe wyjście aud io (ALC888 )

5.1 kanałowe wyjście aud io (ALC662 )

Obsługa H ig h-Def in it io n Aud io

Gniazdo PCI x3 Gniazdo PCI x3

Gniazdo PCI Express x16 x1 Gniazdo PCI Express x16 x1

Gniazdo PCI Express x 1 x2 Gniazdo PCI Express x 1 x2

Złącze napędu dyskietek x1 Złącze napędu dyskietek x1

Złącze Port drukarki x1 Złącze Port drukarki x1

Złącze IDE x1 Złącze IDE x1

Złącze SATA x4 Złącze SATA x4

Złącze panela przedniego x1 Złącze panela przedniego x1

Przedn ie złącze aud io x1 Przedn ie złącze aud io x1

Złącze wejścia CD x1 Złącze wejścia CD x1

Złącze wyjścia S/PDIF x1 Złącze wyjścia S/PDIF x1

Złącze g łówkowe wentylatora procesorax1 Złącze główkowe wentylatora procesorax1

Złącze główkowe wentylatora systemowegox2 Złącze g łówkowe wentylatora systemowegox2

Złącze główkowe kasowan ia

CMOS x1

Złącze USB x2 Złącze USB x2

Złącze zasilania (24 pinowe) x1 Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x2 Złącze zas ilania (4 p ino we) x 2

Klawiatura PS/2 x1

Mys z PS /2 x 1

Port szeregowy x1

Port LAN x1

Port US B x6

Gniazdo audio (Ver 5.x) x6

Gniazdo audio (Ver 6.x) x3

244 mm (S) X 305 mm (W) 244 mm (S) X 305 mm (W)

Funkcje

specjalne

Obsluga

systemu

operacyjne

go

NVIDIA nTunes.

Obsługa RAID 0 / 1 / 0 +1

Windows 2K / XP / V ISTA

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo lnego s ystemu

operacyjnego b ez powiado mienia.

NVIDIA nTunes.

Obsługa RAID 0 / 1 / 0 +1 / 5

Windows 2K / XP / V ISTA

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo lnego s ystemu

operacyjnego b ez powiado mienia.

53

Motherboard Manual

RUSSIAN

TF520 A2+ TF560 A2+

Гнездо AM2 / AM2+ (Обновл ением BIOS)
Процессоры AMD Athlon 64 / Athlon 64 x2 /

Sempron

Арх итектур а AMD 64 разрешать обработка
данных на 32 и 64 бит
Поддержка Hyper Transp ort и Cool’n’Quiet
Поддержка HyperTransport с про пускной
способностью до1GГц

Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает
256/512МБ & 1ГБ/2ГБ DDR2
Максимальная ёмкос ть памяти 8 ГБ
Мод уль памяти с д вухкан альным режимом

DDR2

Поддержка DDR2 533 / 667 / 800
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM

ITE 8716F

Обеспечивает наиболее используемые
действующие фун кц ио н ал ьн ы е возможности

Super I/O.

Интерфейс с ни зким количество м выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ятор скорости
Функц ия ITE "Smart Guard ian "
(Интеллектуальная защита)
Встроенное устройство упр авл ени я
встроенными интерфейсами устр ойств
Режим "хозяина" шины Ultra DMA 33 / 66 / 100

/ 133

Поддержка режима PIO 0~4,
Встроенное последовательное устройство
упра вления ATA
скорость передачи данных до 3 гигабит/с.
Соответствие спецификации SATA версия 2.0.

Realtek RTL 8110SC /
RTL 8100C (дополнительно)

Автоматическо е сог лас овани е 10 / 100 / 1000
Мб/с (гигабитная про пус кная способность
только для гигабитного физи чес ко г о уровн я)
Частичная / полна я дуплексная способность

CPU
(центральн

ый
процессор)

FSB

Набо р
микросхем

Основная
память

Super I/O

IDE

SATA II

Локальная
сеть

Гнездо AM2 / AM2+ (Обновл ением BIOS)
Процессоры AMD Athlon 64 / Athlon 64 x2 /

Sempron

Арх итектур а AMD 64 разрешать обработка
данных на 32 и 64 бит
Поддержка Hyper Transp ort и Cool’n’Quiet
Поддержка HyperTransport с про пускной
способностью до1GГц

nVIDIA nForce 520 nVIDIA nForce 560

Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает
256/512МБ & 1ГБ/2ГБ DDR2
Максимальная ёмкос ть памяти 8 ГБ
Мод уль памяти с д вух кан альным режимом

DDR2

Поддержка DDR2 533 / 667 / 800
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM

ITE 8716F

Обеспечивает наиболее используемые
действующие фун кц ио н ал ьн ы е возможности

Super I/O.

Интерфейс с ни зким количество м выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ятор скорости
Функц ия ITE "Smart Guard ian "
(Интеллектуальная защита)
Встроенное устройство упр авл ени я
встроенными интерфейсами устр ойств
Режим "хозяина" шины Ultra DMA 33 / 66 / 100

/ 133

Поддержка режима PIO 0~4,
Встроенное последовательное устройство
упра вления ATA
скорость передачи данных до 3 гигабит/с.
Соответствие спецификации SATA версия 2.0.

Realtek RTL 8110SC /
RTL 8100C (дополнительно)

Автоматическо е сог лас овани е 10 / 100 / 1000
Мб/с (гигабитная про пус кная способность
только для гигабитного физи чес ко г о уровн я)
Частичная / полна я дуплексная способность

54

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1канальный звуковой вых од (ALC888)

5.1канальный звуковой вых од (ALC662)

Звуко ва я поддержка High- Def in it io n

Контактирующее приспособление
вентил ятора ц ентрального процессораx1
Контактирующее приспособление
вентил ятора системы x2
Открытое контактир ующ ее приспособление

CMOS x1

Клавиатура PS/2 x1
Мышь PS/2 x1
Последоват ельны й порт x1
Пор т LAN x1
USB- порт x6
Гнездо для подключения
наушников (Ver 5.x ) x6
Гнездо для подключения
наушников (Ver 6.x ) x3

NVIDIA nTunes
Поддержка RAID 0 / 1 / 0+1 / 5

Windows 2K / XP / V ISTA
Biostar сохраняет за собой право добавлять

или удалять средства обеспечения для OS с
или без предварительного уведо мл ени я.

Звуко во й
кодек

Слоты

Встроенны
й разъём

Задняя
панель
средств
ввода-выв
ода

Разм ер
панели

Специальн
ые
технически
е
характерис
тики

Поддержка

OS

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1канальный звуковой вых од (ALC888)

5.1канальный звуковой вых од (ALC662)

Звуко ва я поддержка High- Def in it io n
Слот PCI x3 Слот PC I x3
Слот PCI Express x16 x1 Слот PCI Express x16 x1
Слот PCI Express x 1 x2 Слот PCI Express x 1 x2
Разъ ём НГМ Д x1 Разъём НГМД x1
Разъём По рт подключения принтераx1 Разъ ём Порт подключения принтераx1
Разъ ём IDE x 1 Разъём ID E x 1
Разъ ём SATA x4 Разъ ём SATA x4
Разъ ём на лицевой панели x1 Разъ ём на лицевой панели x1
Входной звуковой разъём x1 Входной звуково й разъём x1
Разъ ём ввода для CD x1 Разъ ём ввода для CD x1
Разъ ём вывода для S/PDIF x1 Разъ ём вывод а для S/PDIF x1
Контактирующее приспособление
вентил ятора ц ентрального процессораx1
Контактирующее приспособление
вентил ятора системы x2
Открытое контактир ующ ее приспособление

CMOS x1
USB- разъём x2 USB-разъём x2

Разъ ем питания (24 вы во д) x1 Разъ ем питания (24 вы вод) x1
Разъ ем питания (4 вы вод) x2 Ра зъ ем питания (4 вывод) x2
Клавиатура PS/2 x1
Мышь PS/2 x1
Последоват ельны й порт x1
Пор т LAN x1
USB- порт x6
Гнездо для подключения
наушников (Ver 5.x ) x6
Гнездо для подключения
наушников (Ver 6.x ) x3

244 мм (Ш) X 305 мм (В) 244 мм (Ш) X 305 мм (В)

NVIDIA nTunes
Поддержка RAID 0 / 1 / 0+1

Windows 2K / XP / V ISTA
Biostar сохраняет за собой право добавлять

или удалять средства обеспечения для OS с
или без предварительного уведо мл ени я.

55

Motherboard Manual

ARABIC

ﺲﺒﻘﻡAM2+( ﻲﺑ ﺲﺑ ﻲﺗﺪﺑأ) / AM2

تﺎﺠﻟﺎﻌﻡAMD Athlon 64 /

Athlon 64 x2 / Sempron

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗ AMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮ ﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺖﺏ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Transpo rt و Cool’n’Quiet

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺏ 1000ددﺮﺗ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM ﻦﻡ ةﺮآاذ ﻢﻋﺪﺗ عﻮﻥ DDR2 ﺔﻌﺳ 256/512 ﺎﺠﻴﻡ

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ8 ﺖﻳﺎﺏ ﺎﺠﻴﺝ

ةﺮآاذ ةﺪﺣوDDR2 ﻘﻟا ﺔﺝودﺰﻡةﺎﻨ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 533 / 667 / 800ﺖﻳﺎﺏ ﺎﺠﻴﻡ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ITE 8716F

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨ ﺘ ﺳ ا ﺮﺜآﻷا .

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pin Count Interface

ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳوﺔﺌﻴﺒﻟا:

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Gu ard ian" ﻦﻡ IT E

ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ

ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133

ﻲﺴﻴﺋر ﻊﺿو

د ﻊﺿو ﻢﻋ PIO Mode 0~4

ﻢﻜﺤﺘﻡSerial ATAﻞﻡﺎﻜﺘﻡ

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎ ﻥﺎﻴﺒﻟا ﻞﻘﻥ3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ.

تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺏﺎﻄﻡSATA راﺪﺹﻹا 2.0.

Realtek RTL 8110SC /

RTL 8100C )يرﺎﻴﺘﺥا(

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 ﺖﻳﺎﺏ ﺎﺠﻴﻡ /و ﺔﻴﻥﺎﺙ1 ﺎﺠﻴﺝﺖﺏ/ﺔﻴﻥﺎﺙ

ﻰﻠﻋ ﻂﻘﻓ رﻮﺼﻘﻡ ﺖﺏﺎﺠﻴﺠﻠﻟ يددﺮﺘﻟا قﺎﻄﻨﻟاRTL 8110SC

ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ/ﻲﻔﺼﻨﻟا

ﺲﺒﻘﻡAM2+( ﻲﺑ ﺲﺑ ﻲﺗﺪﺑأ) / AM2

تﺎﺠﻟﺎﻌﻡAMD Athlon 64 /

Athlon 64 x2 / Sempron

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗ AMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮ ﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺖﺏ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Transpo rt و Cool’n’Quiet

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺏ 1000ددﺮﺗ

nVIDIA nForce 520 nVIDIA nForce 560

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ4

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺗ DDR2 ﺔﻌﺳ 256/512 ﺎﺠﻴﻡ

و ﺖﻳﺎﺏ1/2 ﺎﺠﻴﺝﺖﻳﺎﺏ

ةﺮآاذ ةﺪﺣوDDR2 ﻘﻟا ﺔﺝودﺰﻡةﺎﻨ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 533 / 667 / 800ﺖﻳﺎﺏ ﺎﺠﻴﻡ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨﺘﺳا ﺮﺜآﻷا.

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pin Count Interface

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Gu ard ian" ﻦﻡ IT E

ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻢﻜﺤﺘﻡSerial ATAﻞﻡﺎﻜﺘﻡ

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎ ﻥﺎﻴﺒﻟا ﻞﻘﻥ3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ.

تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺏﺎﻄﻡSATA راﺪﺹﻹا 2.0.

Realtek RTL 8110SC /

RTL 8100C )يرﺎﻴﺘﺥا(

ﻰﻠﻋ ﻂﻘﻓ رﻮﺼﻘﻡ ﺖﺏﺎﺠﻴﺠﻠﻟ يددﺮﺘﻟا قﺎﻄﻨﻟاRTL 8110SC

ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ/ﻲﻔﺼﻨﻟا

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ4

و ﺖﻳﺎﺏ1/2 ﺎﺠﻴﺝﺖﻳﺎﺏ

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ8 ﺖﻳﺎﺏ ﺎﺠﻴﺝ

ITE 8716F

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ

ﻲﺴﻴﺋر ﻊﺿو

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 ﺖﻳﺎﺏ ﺎﺠﻴﻡ /و ﺔﻴﻥﺎﺙ1ﺖﺏ ﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ

TF520 A2+ TF560 A2+

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو

ﺔﻳﺰآﺮﻤﻟا

ﻲﺒﻥﺎﺠﻟا ﻲﻡﺎﻡﻷا ﻞﻗﺎﻨﻟا

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻡ

ﺔﻴﺴﻴ ﺋﺮﻟا ةﺮآاﺬﻟا

Super I/O

ﺬﻔﻨﻡIDE

SATA II

ﺔﻴﻠﺥاد ﺔﻜﺒﺵ

56

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

(ALC888)7.1تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

(ALC662)5.1تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ دﺪﻋ1

NVIDIA nTunes

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0 / 1 / 0+1 / 5

Windows 2K / XP / V ISTA

ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿ إ ﻲﻓ ﺎﻬﻘﺤﺏ

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

(ALC888)7.1تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

(ALC662)5.1تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻴﻡﺎ ﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1

ﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡﻲﻡ دﺪﻋ1 ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1

جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1 جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1 ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1

مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ2 مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ2

ﻡ ﺔﻠﺹو ﺢﺴCMOS دﺪﻋ1 ﺢﺴ ﻡ ﺔﻠﺹوCMOS دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1 ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4ﺲﻴﺏﺎﺏد( دﺪﻋ2 ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4ﺲﻴﺏﺎﺏد( دﺪﻋ2

ﺢﻴﺗﺎﻔﻡ ﺔﺣﻮﻟPS/2 دﺪﻋ1

سوﺎﻡ PS/2 دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺢﻴﺗﺎﻔﻡ ﺔﺣﻮﻟPS/2 ﻋ دﺪ1

سوﺎﻡ PS/2 دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻓﺎﻨﻡUS B دﺪﻋ6
تﻮﺹ ﺲﺒﻘﻡ(Ver 5.x) دﺪﻋ6
تﻮﺹ ﺲﺒﻘﻡ(Ver 6.x) دﺪﻋ3

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0 / 1 / 0+1

Windows 2K / XP / V ISTA

ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿ إ ﻲﻓ ﺎﻬﻘﺤﺏ

رﺎﻄﺥإ نوﺪﺏ.

تﻮﺹ ﺲﺒﻘﻡ(Ver 5.x) دﺪﻋ6
تﻮﺹ ﺲﺒﻘﻡ(Ver 6.x) دﺪﻋ3

NVIDIA nTunes

رﺎﻄﺥإ نوﺪﺏ.

ﺔﺤﺘﻓPCI دﺪﻋ3 ﺔﺤﺘﻓPCI دﺪﻋ3
ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1 ﺔﺤﺘﻓx1 6 PCI Express دﺪﻋ1
ﺔﺤﺘﻓPCI Express x 1 دﺪﻋ2 ﺔﺤﺘﻓPCI Express x 1 دﺪﻋ2

ﺬﻔﻨﻡIDE دﺪﻋ1 ﺬﻔﻨﻡIDE دﺪﻋ1
ﺬﻔﻨﻡSATA دﺪﻋ4 ﺬﻔﻨﻡSATA دﺪﻋ4

ﺬﻔﻨﻡCD-IN دﺪﻋ1 ﺬﻔﻨﻡCD-IN دﺪﻋ1

ﺬﻔﻨﻡUS B دﺪﻋ2 ﺬﻔﻨﻡUSB دﺪﻋ2

ﺬﻓﺎﻨﻡUS B دﺪﻋ6

244 ﻢﻡ)ضﺮﻋ (X 305 ﻢﻡ)عﺎﻔﺗرا( 244 ﻢﻡ)ضﺮﻋ (X 305 ﻢﻡ)عﺎﻔﺗرا(

تﻮﺼﻟا ﻚﻳدﻮآ

تﺎﺤﺘﻔﻟا

ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا

ﺔﺣﻮﻠﻟا

ﻞﺥد ﺬﻓﺎﻨﻡ/ جﺮﺥ

ﺔﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا

ﺔﺹﺎﺥ ﺎﻳاﺰﻡ

ﺔﺣﻮﻠﻟا ﻢﺠﺣ

ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻥأ ﻢﻋد

57

Motherboard Manual

JAPANESE

TF520 A2+ TF560 A2+

Socket AM2 / AM2+ (BIOSアップデートで )

AMD Athlon 64 / Athlon 64 x2 / Sempron プロ セ

ッサ

CPU

FSB

チップセット nVIDIA nForce 520 nVIDIA nForce 560

メインメモリ

Super I/O

IDE

SATA II

LAN

AMD 64アーキ テクチャで は、32ビ ットと64ビッ ト計

算が可能です

ハイパートラ ンス ポートとク ールアンド クワイ アット

をサポートし ます

1 GHz の バンド幅ま でハイ パートラン スポ ートをサポ

ートします

DDR2 DIMMスロット x 4

各DIMMは 25 6/512MB & 1GB/2GB DDR2をサポ

ート

最大メモリ容 量8GB

デュアル チ ャン ネルモードDDR2メモリモジ ュール

DDR2 533 / 667 / 800をサポー ト

登録済みDIMMとECC DIMMはサポ ートされま せん

ITE 8716F

もっとも一般 に使 用されるレ ガシーSuper I/O機能を

採用していま す。

低ピンカウン トイ ンターフェ イス

環境コントロ ール イニシアチ ブ、

H/Wモニ ター

ファン速度コ ント ローラ/ モニター

ITE の「スマート ガー ディアン」 機能

統合ID Eコントローラ

Ultra DMA 33 / 66 / 100 / 133バスマ スタ モード

PIO Mode 0~4のサポート 、

統合シリアルATA コントロー ラ

最高3 Gb/秒の データ転送 速度

SATAバージョン2.0仕様に準拠。

Realtek RTL 8110SC / RTL 8100C(オプション )

10 / 100 / 1000 Mb/秒のオ ートネゴシ エーション

(G igab itバ ンド幅 はRTL 8110SC専用 です )

半/全二重機能

58

Socket AM2 / AM2+ (BIOSアップデートで )

AMD Athlon 64 / Athlon 64 x2 / Sempron プロ セ

ッサ

AMD 64アーキ テクチャで は、32ビ ットと64ビッ ト計

算が可能です

ハイパートラ ンス ポートとク ールアンド クワイ アット

をサポートし ます

1 GHz の バンド幅ま でハイ パートラン スポ ートをサポ

ートします

DDR2 DIMMスロット x 4

各DIMMは 25 6/512MB & 1GB/2GB DDR2をサポ

ート

最大メモリ容 量8GB

デュアル チ ャン ネルモードDDR2メモリモジ ュール

DDR2 533 / 667 / 800をサポー ト

登録済みDIMMとECC DIMMはサポ ートされま せん

ITE 8716F

もっとも一般 に使 用されるレ ガシーSuper I/O機能を

採用していま す。

低ピンカウン トイ ンターフェ イス

環境コントロ ール イニシアチ ブ、

H/Wモニ ター

ファン速度コ ント ローラ/ モニター

ITE の「スマート ガー ディアン」 機能

統合ID Eコントローラ

Ultra DMA 33 / 66 / 100 / 133バスマ スタ モード

PIO Mode 0~4のサポート 、

統合シリアルATA コントロー ラ

最高3 Gb/秒の データ転送 速度

SATAバージョン2.0仕様に準拠。

Realtek RTL 8110SC / RTL 8100C(オプション )

10 / 100 / 1000 Mb/秒のオ ートネゴシ エーション

(G igab itバ ンド幅 はRTL 8110SC専用 です )

半/全二重機能

TF520 A2+/TF560 A2+

TF520 A2+ TF560 A2+

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

サウンド

Codec

オンボードコ

ネクタ

背面パネル

I/O

ボードサイズ 244 mm (幅) X 305 mm (高さ) 244 mm (幅) X 305 mm (高さ)

特殊機能

OSサポー ト

7.1チャンネル オーディオ アウ ト (ALC888)

5.1チャンネル オーディオ アウ ト (ALC662)

ハイデフィニ ショ ンオーディ オのサポー ト

PCIスロット x3 PCIスロット x3

PCI Express x16スロット x1 PCI Express x16スロット x1 スロット

PCI Express x 1スロット x2 PCI Express x 1スロット x2

フロッピーコ ネク タ x1 フロッピーコネク タ x1

プリンタポー トコ ネクタ x1 プリンタポー トコネクタ x1

IDE コネクタ x1 IDEコネクタ x1

SATAコネクタ x4 SATAコネクタ x4

フロントパネ ルコ ネクタ x1 フロントパネ ルコネクタ x1

フロントオー ディ オコネクタ x1 フロントオー ディ オコネクタ x1

CDインコネクタ x1 CDインコネクタ x1

S/PDIFアウトコネ クタ x1 S/PDIFアウト コネクタ x1

CPUファンヘッダ x1 CPUファンヘッダ x1

システムファ ンヘ ッダ x2 システムファ ンヘ ッダ x2

CMOSクリアヘッダ x1 CMOSクリアヘッダ x1

USBコネク タ x2 USBコネクタ x2

電源コネクタ (24 ピン) x1 電源コネクタ(24ピン) x 1

電源コネクタ (4ピン) x2 電源コ ネクタ(4ピン) x2

PS/2キーボード x1

PS/2マウス x1

シリアルポー ト x1

LANポート x1

USBポート x6

オーディオジ ャッ ク(Ver 5.x ) x6

オーディオジ ャッ ク(Ver 6.x ) x3

NVIDIA nTunes

RAID 0 / 1 / 0+1のサ ポー ト

Windows 2K / XP / V ISTA

Biostarは事前の サポートな しにOSサ ポー トを追加ま

たは削除する 権利 を留保しま す。

ALC888 (Ver 5.x) / ALC662 (Ver 6.x)

7.1チャンネル オーディオ アウ ト (ALC888)

5.1チャンネル オーディオ アウ ト (ALC662)

ハイデフィニ ショ ンオーディ オのサポー ト

PS/2キーボード x1

PS/2マウス x1

シリアルポー ト x1

LANポート x1

USBポート x6

オーディオジ ャッ ク(Ver 5.x ) x6

オーディオジ ャッ ク(Ver 6.x ) x3

NVIDIA nTunes

RAID 0 / 1 / 0+1 / 5 の サポー ト

Windows 2K / XP / V ISTA

Biostarは事前の サポートな しにOSサ ポー トを追加ま

たは削除する 権利 を留保しま す。

2007/05/21

59