Biostar TA960 Owner's Manual
TA960 Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. There is no guarantee that interference will not occur in a particular
installation.
The vendor makes no representations or warranties with respect to the contents here and
specially disclaims any implied warranties of merchantability or fitness for any purpose.
Further the vendor reserves the right to revise this publication and to make changes to
the contents here without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first obtaining the
vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and we will not
be responsible for any mistakes found in this user’s manual. All the brand and product
names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction.......................................... 1
1.1 Before You Start ................................................................................1
1.2 Package Checklist ............................................................................1
1.3 Motherboard Features...................................................................... 2
1.4 Rear Panel Connectors.................................................................... 3
1.5 Motherboard Layout..........................................................................4
Chapter 2: Hardware Installation ........................... 5
2.1 Installing Central Processing Unit (CPU).......................................5
2.2 Install a Heatsink...............................................................................7
2.3 Fan Headers ......................................................................................8
2.4 Installing System Memory................................................................9
2.5 Connectors and Slots .....................................................................11
Chapter 3: Headers & Jumpers Setup.................... 14
3.1 How to Setup Jumpers...................................................................14
3.2 Detail Settings..................................................................................14
Chapter 4: Useful Help ......................................... 18
4.1 Driver Installation Note................................................................... 18
4.2 Software............................................................................................19
4.3 BIOS Setup ......................................................................................21
4.4 Troubleshooting...............................................................................24
4.5 RAID Function .................................................................................26
Appendix: SPEC In Other Languages .................... 30
German .................................................................................................................30
French ...................................................................................................................32
Italian .....................................................................................................................34
Spanish..................................................................................................................36
Portuguese ...........................................................................................................38
Polish..................................................................................................................... 40
Russian ................................................................................................................. 42
Arabic.....................................................................................................................44
Japanese...............................................................................................................46
CHAPTER 1: INTRODUCTION
1.1 B
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
EFORE YOU START
Prepare a dry and stable working environment with sufficient
lighting.
Always disconnect the computer from power outlet before
operation.
Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the case after
installation. Loose parts will cause short circuits which may
damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be 0 to
45 degrees Celsius.
To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
1.2 PACKAGE CHECKLIST
; Serial ATA Cable x2
; Rear I/O Panel for ATX Case x1
; User’s Manual x1
; Fully Setup Driver DVD x1
Note: The package contents may be different due to the sales region or models in which it was
sold. For more information about the standard package in your region, please contact your
dealer or sales representative.
TA960
1
Motherboard Manual
1.3 MOTHERBOARD FEATURES
SPEC
Socket AM3 / AM3+
CPU
FSB
Chipset AMD 760G + AMD SB710
Super I/O
Main
Memory
Graphics Integrated in AMD 760G Chipset Max Shared Video Memory is 1024MB
SATA II Integrated Serial ATA Controller
LAN Realtek RTL 8111F 10 / 100 / 1000 Mb/s auto negotiation
Sound ALC662
Slots
On Board
Connectors
Back Panel
I/O
AMD Sempron / Athlon II / Phenom II /FX
processors (Maximum Watt: 125W)
Support Hyper Transport 3.0
Supports up to 4.4 GT/s Bandwidth
ITE 8728F-BX
Provides the most commonly used legacy Super
I/O functionality
DDR3 DIMM Slots x 2
Max Memory Capacity 16GB
Each DIMM supports 512MB/1GB/
2GB/4GB/8GB DDR3
PCI Express X16 slot x1 Supports PCI-E X16 expansion card
PCI Express X1 slot x2 Supports PCI-E X1 expansion card
PCI slot x3 Supports PCI expansion cards
SATA Connector x6 Each connector supports 1 SATA device
IDE Connector x1 Each connector supports 2 IDE device
Front Panel Connector x1 Supports front panel facilities
Front Audio Connector x1 Supports front panel audio function
CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)
System Fan Header x2 System Fan Power supply
CMOS Clear Jumper x1 Restore CMOS data to factory default setting
USB Connector x2 Each connector supports 2 front panel USB ports
Power Connector (24pin) x1 Connects to Power supply
Power Connector (4pin) x1 Connects to Power supply
Serial Port Connector x1 Connects to RS-232 Port
Printer Port Connector x1 Each connector supports 1 Printer port
PS/2 Keyboard x1
PS/2 Mouse x1
2
AMD 64 Architecture enables 32 and 64 bit computing
Supports Hyper Transport 3.0
Low Pin Count Interface
Environment Control initiatives
H/W Monitor
ITE's "Smart Guardian" function
Dual Channel Mode DDR3 memory module
Supports DDR3 800/1066/1333/1600(OC)/1866(OC for
AM3+ CPU only)
Registered DIMM and ECC DIMM is not supported
Data transfer rates up to 3 Gb/s
SATA Version 2.0 specification compliant
5.1 channels audio out
High Definition Audio
Connects to PS/2 Keyboard
Connects to PS/2 Mouse
SPEC
DVI port x1
VGA port x1
LAN port x1
USB Port x4
Audio Jack x3
Board Size 200 mm(W) x 295 mm(L)
Special
Features
OS Support Windows XP / Vista / 7 / 8
RAID 0 / 1 / 10 support
Connect to DVI-D monitor
Connect to D-SUB monitor
Connect to RJ-45 Ethernet cable
Connect to USB devices
Provide Audio-In/Out and microphone connection
Biostar reserves the right to add or remove support for any
OS With or without notice.
1.4 REAR PANEL CONNECTORS
TA960
3
Motherboard Manual
1.5 MOTHERBOARD LAYOUT
Note: ■ represents the 1st pin.
4
CHAPTER 2: HARDWARE INSTALLATION
TA960
2.1 I
NSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Locate the CPU socket on the motherboard
Step 2: Pull the socket locking out from the socket and then raise the lever
up to a 90-degree angel.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever to lock the
position.
Note:
1. This MB is designed for AMD 125W AM3/AM3+ CPU, pleases check the CPU
TDP spec before you install it on MB AM3+ CPU TDP spec from below weblink:
http://www.amd.com/us/products/desktop/processors/amdfx/Pages/amdfx-modelnumber-comparison.aspx
2. AMD’s product warranty does not cover damage caused by overclocking (even
when overclocking is enabled via AMD OverDrive™ software).
http://www.amd.com/us/products/desktop/processors/amdfx/Pages/amdfx.aspx
3. Due to the AMD AM3+ CPU designation, we strongly recommend you use AMD
original box CPU fan and add an extra system fan inside the chassis.
6
2.2 INSTALL A HEATSINK
Step 1: Place the heatsink and fan assembly onto the retention frame. Match the
heatsink clip with the socket mounting-lug. Hook the spring clip to the
mounting-lug.
Step 2: On the other side, push the retention clip straight down to lock into the
plastic lug on the retention frame, and then press down the locker until it
stops.
TA960
Note1: Do not forget to connect the CPU fan connector.
Note2: For proper installation, please kindly refer to the installation manual of your CPU
heatsink.
7
Motherboard Manual
2.3 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different due to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
Pin Assignment
1 Ground
2 +12V
3
FAN RPM rate sense
4 Smart Fan Control (By Fan)
SYS_FAN1/2: System Fan Headers
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
Note: CPU_FAN1, SYS_FAN1/2 support 4-pin and 3-pin head connectors. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be connected to pin#2, and the black wire is Ground and should be connected to
GND.
8
2.4 INSTALLING SYSTEM MEMORY
A. Memory Modules
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
TA960
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
9
Motherboard Manual
B. Memory Capacity
DIMM Socket
Location
DDR3_A1 512MB/1GB/2GB/4GB/8GB
DDR3_B1 512MB/1GB/2GB/4GB/8GB
DDR3 Module
Tot a l Memor y Si z e
Max is 16GB.
C. Dual Channel Memory installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status
Disabled O X
Disabled X O
Enabled O O
(O means memory installed, X means memory not installed.)
Note: The DRAM bus width of the memory module must be the same (x8 or x16)
DDR3_A1
DDR3_B1
10
2.5 CONNECTORS AND SLOTS
SATA1~SATA6: Serial ATA 3.0 Gb/s Connectors
These connectors connect to SATA hard disk drives via SATA cables.
Pin Assignment
1 Ground
2 TX+
3 TX4 Ground
5 RX6 RX+
7 Ground
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
TA960
11
Motherboard Manual
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
Note1: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connectors have been plugged-in.
Note2: Insufficient power supplied to the system may result in instability or the
peripherals not functioning properly. Use of a PSU with a higher power output is
recommended when configuring a system with more power-consuming devices.
ATXPWR2: ATX Power Source Connector
This connector provides +12V to CPU power circuit.
Pin Assignment
1 +12V
2 +12V
3 Ground
4 Ground
12
TA960
PEX16_1: PCI-Express Gen2 x16 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slots
- PCI-Express 2.0 compliant.
- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total
PCI1/PCI2/PCI3: Peripheral Component Interconnect Slots
This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards.
Install an Expansion Card
You can install your expansion card by following steps:
1. Read the related expansion card's instruction document before install the
expansion card into the computer.
2. Remove your computer's chassis cover, screws and slot bracket from the
computer.
3. Place a card in the expansion slot and press down on the card until it is
completely seated in the slot.
4. Secure the card’s metal bracket to the chassis back panel with a screw.
5. Replace your computer's chassis cover.
6. Power on the computer, if necessary, change BIOS settings for the
expansion card.
7. Install related driver for the expansion card.
13
Loading...