Biostar MCP6PB M2+ Owner's Manual

MCP6PB M2+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................. 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: RAID Functions .................................. 19

4.1 Operating System............................................................................ 19

4.2 Raid Arrays...................................................................................... 19

4.3 How RAID Works............................................................................. 19

Chapter 5: Useful Help ........................................ 21

5.1 Driver Installation Note.................................................................. 21

5.2 Software............................................................................................ 22

5.3 Award BIOS Beep Code.................................................................. 23

5.4 Extra Information............................................................................ 23

5.5 Troubleshooting............................................................................... 24

Appendix: SPEC In Other Languages ................... 26

German.................................................................................................................. 26

French .................................................................................................................... 28

Italian ..................................................................................................................... 30

Spanish ................................................................................................................... 32

Portuguese ............................................................................................................ 34

Polish...................................................................................................................... 36

Russian ................................................................................................................... 38

Arabic..................................................................................................................... 40

Japane se ................................................................................................................ 42

CHAPTER 1: INTRODUCTION

MCP6PB M2+

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

IDE Cable X 1
Serial ATA Cable X 1
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver CD X 1 (full version manual files inside)
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)

Note: The package contents may be differed by area or your motherboard version.

1

Motherboard Manual

/

1.3 MOTHERBOARD FEATURES

SPEC

Socket AM2 / AM2+

CPU

FSB

Chipset GeForce 6150SE

Super I/O

Main

Memory

Graphics Integrated in GeForce 6150SE Ch ipset Max Shared Video Memory is 256MB

IDE Int eg r at ed IDE Co ntro l ler

SATA II Integrated Serial ATA Controller

LAN Realtek RTL 8201CL PHY

Sound ALC662

Slots

On Board

Connector

AMD Athlon 64 / Athlon 64 FX

/ Sempron / Ph enomX3 / X4 processors

(Maximum Watt: 95W)

Support HyperTransport 1.0 Ghz

Supports up to 2 GT/s Bandwidth

ITE 8718F

Prov ides the most common ly used legacy

Super I/O functionality

DDR2 DIMM Slots x 2

Max Memory Capacity 4GB

Each DIMM supports 256MB/512MB/

1GB/2GB DDR2

PCI Express x16 slot x1 Supports PCI-E x16 expansion cards

PCI slot x1 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector s upports 2 IDE device

SATA Connector x2 Each connector s upport s 1 SATA devices

Front Panel Connector x1 Supports front panel facilit ies

Front Audio Connector x1 Supports front panel audio function

Athlon 64 x2

AMD 64 Architecture enables 32 and 64 b it

computing

Supports Hyper Transport and PowerNow

Low Pin Count Interface

En viro nmen t Co ntr ol in iti at ives

H/W Mon itor

ITE's "S mart Guard ian " funct ion

Dual Channel Mode DDR2 memo ry module

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (by AM2+ CPU)

Register ed D IMM and ECC D IMM is not supported

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

Data transfer rates up to 3 Gb/s

SATA Vers io n 2.0 s pe cif ic at ion co mp liant

10 / 100 Mb/s auto negot iation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

2

SPEC

CPU Fan header x1 CPU Fan power supply (with Smart Fan function)

System Fan head er x1 Sys tem Fan Power s upply

CMOS clear header x1 Restore CMOS data to factory default

USB connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

PS/2 Keyboard x1

PS/2 Mous e x1

Back Panel

I/O

Board Size 170 mm(W) x 235 mm(L) MicroATX

Special

Features

OS Support Windows XP / Vista / 7

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

RAID 0 / 1

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 ethe rnet cable

Connect to USB dev ices

Provide Audio-In/Out and microphone connection

Biostar Reserves the right to add or remove support

for any OS With or without notice.

1.4 R

EAR PANEL CONNECTORS

MCP6PB M2+

PS/2
Mouse

PS/2
Keyboard

VGA

LAN

Line In/
Surround

Line Out

Mic In 1/
Bass/ Center

USBX2USBX2

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

JKBMS

JKB_PWR

JATXPWR2

Socket AM2+

JATXPWR1

JVGA

JUSB1

JUSBLAN1

JAUDIO1

Note: represents the 1■

LAN

Codec

JUSBPWR1

BAT1

JAUDIOF

JCFAN

JCOM

JPRNT

PEX16_1

PCI1

st

pin.

GeForce

6150S E

FDD

BI OS

DIMMB1

DIMMA1

JUSBPWR2

JUSB2

Super I/O

SATA2 SATA1

J PANEL1

JSFAN

IDE

JU SB3

JCMOS1

4

CHAPTER 2: HARDWARE INSTALLATION

MCP6PB M2+

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.

5

Motherboard Manual

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU

transition, you may encounter the situation that the ne w system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.

6

MCP6PB M2+

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN: CPU Fan Header

Pin

Assignment

1

4

JSFAN: System Fan Header

1 Ground
2 +12V
3

FAN RPM r at e
sense

4 Smart Fan

Control (By Fan)

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate

sense

13

Note:

The JCFAN supports 4-pin head connector; the JSFAN, 3-pin head connector. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be co nnected to pin#2, and the black wire is Ground and should be connected to
GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMA1

DIMMB1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot so that the notch on the DIMM matches the break
on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8

MCP6PB M2+

B. Memory Capacity

DIMM Socket

Location

DIMMA1 256MB/512MB/1GB/2GB

DIMMB1 256MB/512MB/1GB/2GB

DDR2 Module

Total M emory

Size

Max is 4GB.

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:

Install memory module of the same density in pairs, shown in the following
table.

Dual Channel Status DIMMA1 DIMMB1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

9

Motherboard Manual

2.4 CONNECTORS AND SLOTS

FDD: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cable.

234

IDE: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connector can connect a master and a slave drive, so you can connect
up to two drives.

133

21

3940

10

MCP6PB M2+

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX16_1

PCI1: Peripheral Component Interconnect Slot

This motherboard is equipped with 1 standard PCI slot. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1

11

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep,
and speaker connection. It allows user to connect the PC case’s front panel
switch functions.

PWR_LE D

On/Off

-

9
1

++

SPK

HLED

16

8

-

+

RST

12

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 11 N/A N/ A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

MCP6PB M2+

JATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

12

1

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

24

13

JATXPWR2: ATX Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

34

1

2

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

Note:

Before power on the system, please make sure that both JATXPWR1 and JATXPWR2
connectors have been plugged-in.

13

Motherboard Manual

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

JUSB2 JUSB3

10 9

21

SATA1/SATA2: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 2 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA2 SATA1

Assignment

Pin

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 NC

10 Key

Pin

Assignment

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

14

14 7

MCP6PB M2+

JAUDIOF: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key

210

9 Left line in

10 Jack Sense

19

JCOM: Serial port Connecto r

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin

Assignment

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground

210

19

6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator

10 NC

15

Motherboard Manual

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

31

31

Pin 1-2 Close:

Normal Operation (default).

31

Pin 2-3 Close:

Clear CMOS data.

16

JPRNT: Printer Port Connector

This header allows you to connect printer port on the PC.

2

125

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

MCP6PB M2+

17

Motherboard Manual

JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBPWR2: +5V for USB ports at front panel (JUSB2/JUSB3).

Pin 2-3 Close:

JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1.
JUSBPWR2: +5V STB for USB ports at front panel (JUSB2/JUSB3).

JUSBPWR1

1

3

3

1

JUSBPWR2

JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse

1

3

Pin 1-2 close

1

3

Pin 2-3 close

18

31

31

Pin 1-2 close

+5V for PS/2 keyboard and
mouse.

Pin 2-3 close

+5V STB for PS/2 keyboard
and mouse.

31

CHAPTER 4: RAID FUNCTIONS

MCP6PB M2+

4.1 O

Supports Windows XP and Windows Vista.

PERATING SYSTEM

4.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a lar ge file int o s maller blo cks and per forms dis k r eads and wr ites across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

 Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the

platform.

 Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

 Benefits: provides increased data throughput, especially for large files. No

capacity loss penalty for parity.

 Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

 Fault Tolerance: No.

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

19

Motherboard Manual

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliab le
media.

Features and Benefits

 Drives: Minimum 2, and maximum is 2.
 Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

 Benefits: Provides 100% data redundancy. Should one drive fail, the

controller switches to the other drive.

 Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

 Fault Tolerance: Yes.

20

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

CHAPTER 5: USEFUL HELP

MCP6PB M2+

5.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

21

Motherboard Manual

5.2 SOFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software In stallation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

BIOScreen Utility

This utility allows you to personalize your boot logo easily. You can choose
JPG or BMP as your boot logo so as to customize your computer.

Please follow the following instructions to update boo logo:

1. Load Image：Choose the picture as the boot logo.

2. Transform：Transform the picture for BIOS and preview the result.

3. Update Bios：Write the picture to BIOS Memory to complete the update.

22

5.3 AWARD BIOS BEEP CODE

Beep Sound Meaning

One long beep followed by two short
beeps

High-low siren sound CPU overheated

One Short beep when system boot-up No error found during POST

Long beeps every other second No DRAM detected or install

Video card not found or video card
memory bad

System will shut down automatically

5.4 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

MCP6PB M2+

23

Motherboard Manual

5.5 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

System cannot boot after user installs a
second hard drive.

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

24

MCP6PB M2+

This page is intentionally left blank.

25

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sp ezif ika tio nen

Sockel AM2 / AM2+

CPU

FSB

Chipsatz GeForce 6150SE

Super E/A

Arbeitsspeich

er

AMD Athlon 64 / Ath lon 64 FX / Althlon 64

X2 / S empron / Ph enomX3 / X4

Prozessoren (Maximales Watt: 95W)

Unterstützt HyperTransport 2.0 Ghz mit

einer

Bandbreite von bis zu 4 GT/s

ITE8716F

Biet et die häufig ver wend eten a lten Sup er

E/A-Funktionen.

DDR2 DIMM-Steckplätze x 2

Max. 4GB Arbeitsspeicher

Jeder DIMM unterstützt 256MB/512MB/

1GB/2GB DDR2.

Die AMD 64-Architektur unterstütz t eine 32-Bit- und

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport und PowerNow

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533 / 667 / 800

Unterstützt DDR2 1066 (by AM2+ CPU)

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Grafik Integrierter GeForce 6150SE-Chipsatz Max. 256 MB gemeinsam benutzter V ideospeicher

IDE Integriert er IDE -Co ntrolle r

SATA Integrierter Serial ATA-Controller

LAN Realtek RTL 8201CL PHY

HD

Audio-Unters

tützung

ALC662

Ultra DMA 33 / 66 / 100 / 133 Bus Master- Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3 Gb /s

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

26

Steckplätze

Onboard-Ans

chluss

Rückseiten-E

/A

Platinengröß

e

MCP6PB M2+

Sp ezif ika tio nen

PCI Express x16 Steckplatz x1

PCI-Steckp latz x1

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x2 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfter-Sockel x1

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS lös chen"- So ckel x1

USB-Anschluss x2

Stromanschluss (24-polig) x1

St romans chlus s (4-po lig ) x1

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss x1

PS/2-Tastatur x1

PS/2-Maus x 1

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

170 mm (B) X 235 mm (L)

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan -F un ktion )

Jeder Anschluss unterstützt 2

Fronttafel-USB-Anschlüsse

Sonderfunkti

onen

OS-Unterstü

tzung

Unterstützt RAID 0 / 1

Windows XP / Vista / 7

Biostar behält s ich das Recht vor, ohne Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

27

Motherboard Manual

FRENCH

SPEC

Socket AM2 / AM2+

UC

Bus frontal

Chipset GeForce 6150SE

Super E/S

Mémoire

principale

Graphiques Integré dans la chipset GeForce 6150SE Mémoire vidéo partagée maximale de 512 Mo

Processeurs AMD Athlon 64 / Athlon 64 FX

/ Alth lon 64 X2 / S empron / Pheno mX3 /

X4 (Watt maximum : 95W)

Prend en charg e Hyp er Transport 2.0 Ghz

jusqu'à une bande passante de 4 GT/s

ITE 8718F

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Fentes DDR2 DIMM x 2

Capacité mémoire max imale de 4 Go

Chaque DIMM prend en charge des DDR2

de 256Mo/512Mo/1Go/2Go

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en charge Hyp er Transport et Power Now

Int e rf ace à f a ib le co mpt e d e b roches

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel

Fonction "Gardien intelligent" de l'ITE

Module de mémo ire DDR2 à mod e à dou b le vo ie

Prend en charge la DDR2 533 / 667 / 800

Prend en charge la DDR2 1066 (by AM2+ CPU)

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

IDE Contrôleur IDE intégré

SATA

LAN Realtek RTL 8201CL PHY

Prise en

charg e

aud io HD

Fentes

Connecteur

embarqué

Contrô leur Serial ATA int é gr é

ALC662

Fente PC I Express x 16 x1

Fente PCI x1

Connecteur de disquette x1

Connecteur IDE x1

Connecteur SATA x2

28

Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3 Go/s.

Co nfo rme à la spécificat ion S ATA Ver s ion 2 .0

10 / 100 Mb/s négociation automatique

Half / Full duplex capability

Sortie aud io à 5 .1 voies

Prise en charge de l'aud io haute déf inition

Chaque conne ctor prend en charge 2 lecteu rs de

disquettes

Chaque connecteur pr end en charge 2 périphériques

IDE

Chaque connecteur pr end en charge 1 périphérique

SATA

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Embase de ventilateur UC x1

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x2

Connecteur d' aliment ation x1

(24 broches)

Connecteur d' aliment ation x1

(4 broch es)

Connecteur de Port d'imprimante x1

Connecteur de Port série x1

Clavier PS/2 x1

E/S du

panneau

arrière

Dimension

s de la

cart e

Fonctionnal

ité s

spéciales

Support SE Windows XP / Vista / 7

Souris PS/2 x1

Port VGA x1

Port LA N x1

Port USB x4

Fiche aud io x3

170 mm (l) X 235 mm (H)

Prise en charge RAID 0 / 1

MCP6PB M2+

SPEC

Alimentation électrique du ventilateur UC (avec

fonction de ventilateur intelligent)

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Chaque conne ctor prend en charge 1 Port

d'imprimante

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

29

Motherboard Manual

ITALIAN

SPECIFICA

Socket AM2 / AM2+

CPU

FSB

Chipset GeForce 6150SE

Super I/O

Memor ia

principale

Grafica Integrata nel Chipset GeForce 6150SE La memoria video condivisa massima è di 256 MB

IDE Controller IDE integrato

SATA Controller Serial ATA integrato

LA N Realtek RTL 8201CL PHY

Supporto

audio HD

Allo ggi

Connettori

su scheda

Processori AMD Athlon 64 / Athlon 64 FX

/ Althlon 64 X2 / Sempron / PhenomX3 /

X4 (Watt massimo: 95W)

Supporto di HyperTransport 2.0 Ghz

fino a 4 GT/s di larghezza di banda

ITE 8718F

Fo rn isce le funz io nalit à legacy Sup er

I/O usate più comunemente.

Alloggi DIMM DDR2 x 2

Capacità massima della memoria 4GB

Ciascun DIMM supporta DDR2

256MB/512MB/1GB/2GB

ALC662

Alloggio PCI Express x16 x1

Allo ggio PC I x 1

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x2 Ciascun connettore supporta 1 unità SATA

Co nnetto re pann ello fr ont ale x 1 Supporta i s ervizi de l p anne llo f ro ntale

L’arch itettu ra AMD 64 ab ilit a la co mputazione 32

e 64 bit

Supporto di Hyper Transport e PowerNow

Interfaccia LPC (Low Pin Count)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 533 / 667 / 800

Supporto di DDR2 1066 (by AM2+ CPU)

DIMM registrati e DIMM ECC non sono supportati

Modalità Bus Master Ultra DMA 33 / 66 / 100 /

133

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3 Gb/s.

Co mpatibi le s pec ifi che SATA Version e 2.0.

Negoziazione automatica 10 / 100 Mb/s

Capacità Half / Full Duplex

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

30

I/O

pannello

posteriore

Dimension

i scheda

Caratterist

iche

speciali

Sistemi

oper at ivi

supportati

MCP6PB M2+

SPECIFICA

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Co llet t ore vento lina C PU x 1

Co llet t ore vento lina sistema x 1 Aliment az ione vento lina di sist ema

Co llet t ore cancellaz ione CMOS x 1

Connettore USB x2

Connettore aliment azione x1

(24 pin)

Connettore aliment azione x1

(4 pin)

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Connettore Po rta seriale x1

Tas tiera P S /2 x1

Mou se PS /2 x 1

Porta VGA x1

Porta LA N x1

Porta USB x4

Connettore audio x3

170 mm (larghezza) x 235 mm

(altez za)

Supporto RAID 0 / 1

Windows XP / Vista / 7

Alimentazione ventolina CPU (con funzione Smart

Fan)

Ciascun connettore supporta 2 porte USB

pannello frontale

Biostar si riserva il dir itto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

31

Motherboard Manual

SPANISH

Conector AM2 / AM2+

Procesadores AMD Athlon 64 / Athlon 64

CPU

FSB

Conjunto

de chips

Súper E/S

Memoria

principal

Gráficos

IDE Controlador IDE integrado

SATA Controlador ATA Serie Integrado

Red Local Realtek RTL 8201CL PHY

Soporte de

sonido HD

Ranuras

en p laca

FX / Athlon 64 X2 / Sempron / PhenomX3

/ X4

(Vatio máx imo: 95W)

Admite HyperTransport 2.0 Ghz con un

ancho de banda d e hasta 4 GT /s

GeForce 6150SE

ITE 8718F

Le ofrece las funcionalidades heredadas

de uso más común Súper E/S.

Ranuras DIMM DDR2 x 2

Capacidad máxima de memoria de 4GB

Cada DIMM admite DDR de 256MB/

512MB/1GB/2GB

Integrados en el conjunto de chips

GeForce 6150SE

ALC662

Ranura PCI Express x16 X1

Ranura PCI X1

Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible Conectores

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Especificación

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

Soporta las tecnologías Hyper Transport y PowerNow

Interfaz de cuenta Low Pin

In ic iativas de co ntrol d e entorno,

Monitor hardware

Función "Guardia inteligente" de ITE

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533 / 667 / 800

Admite DDR2 de 1066 (by AM2+ CPU)

No admite DIMM registrados o DIMM compatibles con

ECC

Memoria máxima de vídeo compartida de 256 MB

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible co n la ve rsió n SATA 2 .0 .

Negociación de 10 / 100 Mb/s

Funciones Half / Full dúplex

Salida de sonido de 5.1 canales

Soporte de sonido Alta Definición

32

Panel

trasero de

E/S

Ta mañ o de

la placa

Funciones

especiales

Soporte de

sistema

operativo

MCP6PB M2+

Especificación

Conector SATA X2 Cada conector soporta 1 dispositivos SATA

Co nect or de p anel fro nta l X 1 S o porta ins t alacio nes en e l p an e l f ro nta l

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector soporta 2 puerto s USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Conector Puerto serie X1

Tec lad o P S /2 X 1

Ratón PS/2 X1

Puerto VGA X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

170 mm. (A) X 235 Mm. (H)

Admite RAID 0 / 1

Windows XP / Vista / 7

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

33

Motherboard Manual

PORTUGUESE

ESPECIFICAÇÕES

Socket AM2 / AM2+

Processadores AMD Athlon 64 / Athlon 64

CPU

FSB

Chipset GeForce 6150SE

Especificaç

ão Super

I/O

Memória

principal

Placa

gráf ica

IDE Controlador IDE integrado

SATA Controlador Serial ATA integrado

LAN Realtek RTL 8201CL PHY

Suporte

para áudio

de alta

definição

Ranhuras

na placa

FX / Althlon 64 X2 / Sempron / PhenomX3

/ X4

(Watt máx imo: 95W )

Suporta a tecnologia HyperTransport 2.0

Ghz com u ma largura de band a at é 4

GT/s

ITE 8718F

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Ranhuras DIMM DDR2 x 2

Capacidade máx ima de memó ria: 4 GB

Cada módulo DIMM suporta uma

memória DDR2 de 256 MB/512MB/

1GB/2GB

Integrada no chipset GeForce 6150SE Memória de vídeo máxima partilhada: 256 MB

ALC662

Ranhura PCI Express x16 x1

Ranhura PCI x1

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes Conectores

Conector IDE x1 Cada conector suporta 2 disposit ivos IDE

A arquitectura A MD 64 permite u ma computação de

32 e 64 bits

Suporta as tecnolog ias Hyper Trans po rt e PowerNow

Interface LPC (Low Pin Count).

In ic iativas para co nt ro lo do a mb iente

Monitorização do hardware

Função "Smart Guardian" d a ITE

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 533 / 667 / 800

Suporta módulos DDR2 1066 (by AM2+ CPU)

Os módulos DIMM registados e os DIMM ECC não são

suportados

Modo Bus master U ltra DMA 33 / 66 / 100 / 133

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3 Gb/s.

Compat ibilidad e co m a especificação SATA vers ão 2.0.

Auto negociação de 10 / 100 Mb/s

Capacidade semi/full-duplex

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

34

Entradas /S

aídas no

painel

traseiro

Tamanho

da placa

Característi

cas

especiais

Sistemas

operativos

suportados

MCP6PB M2+

ESPECIFICAÇÕES

Conector SATA x2 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áudio frontal x1 Supo rta a fun ção de áud io no pa inel fronta l

Conector da ventoinha da CPU x1

Conector da ventoinha do s istema x1 Alimentação da ventoinha do s istema

Conector para limpeza do CMOS x1

Conector USB x2 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos )

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Conector da Porta série x1

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta VGA x1

Porta LA N x1

Porta USB x4

Tomada de áudio x3

170 mm (L) X 235 mm (A)

Suporta as funções RA ID 0 / 1

Windows XP / Vista / 7

Alimentação da ventoinha da CPU (com a função

Smart Fan)

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av iso p révio.

35

Motherboard Manual

POLISH

SPEC

Socket AM2 / AM2+

Procesor

FSB

Chipset GeForce 6150SE

Pamięć

główna

Super I/O

Graf ika

IDE Zintegrowany kontroler IDE

SATA Zintegrowany kontroler Serial ATA

LAN Realtek RTL 8201CL PHY

Obsługa

aud io HD

Gniazda

Złącza

wbud owan

e

36

AMD Athlon 64 / Athlon 64 FX / Althlon 64

X2 / Sempron / PhenomX3 / X4 Procesory

(Maksymalny Watt: 95W)

Obsługa HyperTransport 2.0 Ghz o

szerokości pasma do 4 GT/s

Gniazda DDR2 DIMM x 2

Maks. wielkość pamięci 4GB

Każde gniazdo DIMM obs ługuje moduły

256MB/512MB/1GB/2GB DDR2

ITE 8718F

Zapewnia najbardziej powszechne

funkcje Super I/O.

Zintegrowan a w ch ipsec ie GeForce

6150SE

ALC662

Gniazdo PCI Express x16 x1

Gniazdo PCI x1

Złącze napędu dyskietek x1 Każde złącze obs ługuje 2 napędy dyskietek

Złącze IDE x1 Każde złącze obs ługuje 2 urządzenia IDE

Złącze SATA x2 Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie z łącze aud io x1 Obsługa funkcji audio na panelu przednim

Architektura AMD 64 umożliwia przetwarzanie 32 i 64

bitowe

Obsługa Hyper Transport oraz PowerNow

Mod uł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 533 / 667 / 800

Obsługa DDR2 1066 (by AM2+ CPU)

Brak obsług i Registered DIMM oraz ECC D IMM

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Mon itor H /W

Funkcja ITE "Smart Guardian"

Maks. wielkość wspó łdz ielonej p a mięci video wynosi

256 MB

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 Mb/s z automatyczną negocjacją szybkości

Działanie w trybie połowicznego / pełnego dupleksu

5.1 kanałowe wyjście audio

Obsługa H igh- Def in ition A udio

Back Panel

I/O

Wymiary

płyty

Funkcje

specjaln e

Obsluga

systemu

operacyjne

go

MCP6PB M2+

SPEC

Złącze głó wkowe wentylatora procesora

x1

Złącze głó wko we wenty latora

systemowego x1

Złącze głó wkowe kasowan ia CMOS x1

Złącze USB x 2

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x1

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Złącze Port szeregowy x 1

Klawiatura PS/2 x1

Mys z PS /2 x 1

Port VGA x1

Port LA N x1

Port USB x4

Gniazdo audio x3

170 mm (S) X 235 mm (W)

Obsługa RAID 0 / 1

Windows XP / Vista / 7

Zasilanie wentylatora procesora (z funkcją Smart Fan)

Zasilanie wentylatora systemowego

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsługi do wo lnego s ys t emu

operacyjnego b ez powiado mienia.

37

Motherboard Manual

RUSSIAN

CPU
(централь

ный

процессор

)

FSB

Набо р
микросхем

Основная

память

Super I/O

Графика

IDE

SATA

Локальна я
сеть

Звуко вая

поддержка

жестког о

диска

Слоты

Встроенны

й разъём

38

Гнездо AM2 / AM2+
Процессоры AMD Athlon 64 / Athlon 64

FX / Althlon 64 X2 / Sempron / PhenomX3
/ X4

(Макси мальный ватт: 95W)

Поддержка HyperTransport 2.0 Ghz с
пропускной способностью до 4 GT/s

GeForce 6150SE

Слоты DDR2 DIMM x 2

Максимальная ёмкость памяти 4 ГБ
Каждый модуль DIMM поддерживает

256МБ /512МБ /1ГБ/2ГБ DDR2

ITE 8718F

Обеспечивает наиболее используемые
действующие фун кц и онал ьные

возможно сти Super I/O.

Встроенная в набор микросхем GeForce

6150SE

Встроенное устройс тво управл ени я

встроенными интерфейсами устро йств

Встроенное послед оват ельное

устройс тво управлен ия ATA

Realtek RTL 8201CL PHY

ALC662

Слот PCI Express x16 x1

Слот PCI x1

Разъ ём НГМД x1

Разъ ём IDE x1

Разъ ём SATA x2 Каждый разъём поддерживает 1 устройство SATA

СПЕЦ

Арх итектура A MD 64 разрешать обработка данных
на 32 и 64 бит

Поддержка Hyper Trans port и Pow erNow

Мод ул ь памяти с двухкан альн ым режимом DDR2

Поддержка DDR2 533 / 667 / 800
Поддержка DDR2 1066 (b y AM2+ CPU)

Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Интерфейс с ни зким количеством выводов

Инициативы по охран е окружающей среды,
Аппаратный монитор

Функция ITE "S mart Guard ian" (Интеллектуальная
защит а)

Максимальная совместно используемая видео

память составляет 256 МБ

Режим "хозяина" шины Ultra DMA 3 3 / 66 / 100 / 133

Поддержка режима PIO 0~4,

скорость передачи данных до 3 гигабит/с.

Соответствие специ фикации SATA версия 2.0.

Автоматическо е согласо вани е 10 / 100 Мб /с
Частичная / полна я дуплексная способность

Звуко вая поддержка High -Defin ition

5.1канальный звуковой выхо д

Каждый разъём поддерживает 2 накопителя на

гибких магнитных дисках

Каждый разъём поддерживает 2 встроенных
интерфейса накопителей

Задняя
панель

средств

ввода-выв
ода

Разм ер

панели

Специальн

ые

техническ

ие

характери
стики

Поддержк
а OS

MCP6PB M2+

СПЕЦ

Разъ ём на лицевой панели x1 Поддержка устройств на лицевой панели

Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели

Контактирующее приспособление

вентил ятора центрального

процессора x1

Контактирующее приспособление

вентил ятора системы x1

Открытое контактирующе е

приспособление CMOS x1

USB- разъём x2

Разъ ем питания (24 вывод) x1

Разъ ем питания (4 вывод) x1

Разъ ём Порт подклю чения

принтера x1

Разъ ём Послед ов ательный порт x1

Клавиатура PS/2 x1
Мышь PS /2 x1

Пор т VGA x1

Пор т LAN x1
USB- порт x4

Гнездо для подключени я
наушников x3

170 мм (Ш) X 235 мм (В)

Поддержка RAID 0 / 1

Windows XP / Vista / 7

Источник пит ания для вентил ятор а центрального

процессора (с функц ией интеллектуального

вентил ятора )

Источник пит ания для вентил ятор а системы

Каждый разъём поддерживает 2 USB-порта на
лицевой панели

Каждый разъём поддерживает 1 По рт подключения

принтера

Biostar сохраняет за собой право добавлять или
удаля ть средства обеспечения для OS с или без

предварительного уведомления.

39

Motherboard Manual

ARABIC

ﻦﻜﻤﺗ ﺔﻴﻨﻘﺗ AMD 64 ﺔﻋﺮﺴﺑ ﺔﻴﺑﻮﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺟإ 32 و64 ﺖﺑ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Trans port و 3 Power Now

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pin Count Interface

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺟﻷا ﺔﻟﺎﺡ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Gu ardian" ﻦﻡ ITE

ةﺮآاذ ةﺪﺡوDDR2 ﻘﻟا ﺔﺟودﺰﻡةﺎﻨ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 533 / 667 / 800 ﺖیﺎﺑ ﺎﺠﻴﻡ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 1066ﺖیﺎﺑ ﺎﺠﻴﻡ

(DDR2 1066 is by AM2+ CPU)

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠ ﺗو ECC

ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮیﺪ ﻴﻔﻟا ﺔآﺮﺘﺸﻤﻟا 256 ﺎﺠی ﺖیﺎﺑ

ﺔﻴﻨﻘ ﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼﺗ ﻰﻟإ 3 ﺖﺑﺎﺠﻴﺟ/ﺔﻴﻥﺎﺙ.

ﺔﻘﺑﺎﻄﻡ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0 .

ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ/ﻲﻔﺼﻨﻟا

5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا

ﻦﻡ ﻒیﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗ

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآﺮﺤﻡ ﻢﻋﺪی

ةﺰﻬﺟأ ﻦﻡ ﻦﻴﻨﺙ ا ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪی IDE

ةﺰﻬﺟأ ﻦﻡ ﺪﺡاو ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیSATA

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

تﺎﻔﺻاﻮﻤﻟا

ﺲﺒﻘﻡAM2 / AM2+

تﺎﺠﻟﺎﻌﻡAMD Athlon 64 / Athlon 64 FX / Sempron /

PhenomX3 / X4 / Althlon 64 X2

(طاو ىﻮﺼﻗ: 95و)

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼی ددﺮﺘﺑ 2.0Ghz 4 GT/s

GeForce 6150SE ﺔﻋﻮﻤﺠﻡ ﺢﺋاﺮﺸﻟا

ITE 8718F

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨﺘ ﺳا ﺮﺜآﻷا .

ﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ ى4 ﺖیﺎﺑ ﺎﺠﻴﺟ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺗ DDR2 ﺔﻌﺳ

ﻖﺋﺎﻗر ﻲﻓ ﺔﺠﻡﺪﻡ GeForce 6150SE

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 ﺖیﺎﺑ ﺎﺠﻴﻡ /ﺔﻴﻥﺎﺙ

Realtek RTL 8201CL PHY

256/512 ﺎﺠﻴﻡ

ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ ﺬﻔﻨﻡ IDE

ﻢﻜﺤﺘﻡ Serial ATA ﻞﻡﺎﻜﺘﻡ

ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1

ﺔﺤﺘﻓPCI دﺪﻋ1

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ2

و ﺖیﺎﺑ1/و 2 ﺎﺠﻴﺟﺖیﺎﺑ

ALC662

ﺬﻔﻨﻡIDE دﺪﻋ1

ﺬﻔﻨﻡSATA دﺪﻋ2

ةﺪﺡو ﺔﺠﻟﺎﻌﻤﻟا

ﺔیﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻡﺎﻡﻷا ﻲﺒﻥﺎﺠﻟا

Super I/O

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

ﺔﻗﺎﻄﺑ تﺎﻡﻮﺳﺮﻟا

SATA

ﺵﺔﻜﺒ ﺔﻴﻠﺥاد

ﻢﻋد تﻮﺼﻟا ﻲﻟﺎﻋ

ﻒیﺮﻌﺘﻟا

تﺎﺤﺘﻔﻟا

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄ ﺳ

ﺔﺡﻮﻠﻟا

40

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟ ﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇ و ﻢﻋﺪی

ﺔﻔﻴﻇو ﻊﻡ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺡوﺮﻤﻟ ﺔﻗﺎﻄ ﻟا ﻞﻴﺹﻮﺘﻟ

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیUSBﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟﺎﺑ

ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ

رﺎﻄﺥإ نوﺪﺑ.

MCP6PB M2+

تﺎﻔﺻاﻮﻤﻟا

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1

و ﺔﺡوﺮﻡ ﺔﻠﺹوﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡ دﺪﻋ1

مﺎﻈﻨﻟا ﺔﺡوﺮﻡ ﺔﻠﺹو دﺪﻋ1

ﺢﺴ ﻡ ﺔﻠﺹوCMOS دﺪﻋ1

ﺬﻔﻨﻡUS B دﺪﻋ2

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺑد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4سﻮ ﺑد( دﺪﻋ1

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺢﻴﺗﺎﻔﻡ ﺔﺡﻮﻟPS/2 دﺪﻋ1

سوﺎﻡ PS/2 دﺪﻋ1

ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ دﺪﻋ1

170 ﻢﻡ)ضﺮﻋ (X 235 ﻢﻡ)عﺎﻔﺗرا( ﻢﺠﺡ ﺔﺡﻮﻠﻟا

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0 / 1 ﺔﺹﺎﺥ ﺎیاﺰﻡ

Windows XP / Vista / 7

ﺬﻔﻨﻡVG A دﺪﻋ1

ﺬﻓﺎﻨﻡUSB دﺪﻋ4

تﻮﺹ ﺲﺒﻘﻡ ﺪﻋ3

ﺬﻓﺎﻨﻡ ﻞﺥد/جﺮﺥ

ﺔﺡﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

ﻢﻋد ﺔﻤﻈﻥأ ﻞﻴﻐﺸﺘﻟا

41

Motherboard Manual

JAPANESE

Socket AM2 / AM2+

CPU

FSB

チップセッ

ト

メインメモ

リ

Super I/O

グラフィッ

クス

IDE 統合 IDE コントローラ

SATA 統合シ リアルATA コントローラ

LAN Realtek RTL 8201CL PHY

HDオ ーディ

オのサポー

ト

スロット

オンボード

コネクタ

AMD Athlon 64 / Athlon 64 FX / Althlon 64

X2 / S empron / Ph enomX3 / X4 プロセッ

サ (最高のワッ ト: 95W )

4 GT/sのバン ド幅までハ イパートラ ンス ポー

ト2.0 GHzをサ ポートしま す

GeForce 6150SE

DDR2 DIMMスロット x 2

最大メモリ容 量4GB

各DIMMは 25 6MB/512MB/1GB/2GB

DDR2をサポート

ITE 8718F

もっとも一般 に使 用されるレ ガシーSuper I/O

機能を採用し てい ます。

GeForce 6150SEチップセ ット に統合 最大の 共有ビ デオメモリ は256 Bです

ALC662

PCI Express x16スロット x1

PCIスロット x1

フロッピーコ ネク タ x1 各コネクタは 2つのフロ ッピードラ イブをサポ ートし ます

IDE コネクタ x1 各コネクタは 2つのIDE デバイスをサポ ートします

SATAコネクタ x2 各コネクタは 1つのSATAデバイスをサポ ート します

仕様

AMD 64アーキ テクチャで は、32ビットと64 ビッ ト計算が可

能です

ハイパートラ ンス ポートとク ールアンド クワイ アットをサ ポ

ートします

デュアル チ ャン ネルモードDDR2メモリモジ ュール

DDR2 533 / 667 / 800 をサポート

DDR2 1066 をサポート (by A M2+ CPU)

登録済みDIMMとECC DIMMはサポ ートされま せん

低ピンカウン トイ ンターフェ イス

環境コントロ ール イニシアチ ブ、

H/Wモニター

ITE の「スマート ガー ディアン」 機能

Ultra DMA 33 / 66 / 100 / 133バスマ スタモード

PIO Mode 0~4のサポート 、

最高3Gb/秒の データ転送 速度

SATAバージョン2.0仕様に準拠。

10 / 100 Mb/秒のオ ートネ ゴシエーシ ョン

半/全二重機能

5.1チャンネル オーディオ アウ ト

ハイデフィニ ショ ンオーディ オのサポー ト

42

仕様

フロントパネ ルコ ネクタ x1 フロン トパネル機 能をサポー トしま す

フロントオー ディ オコネクタ x1 フロン トパネ ルオーディ オ機能をサ ポー トします

CPUファンヘッダ x1 CPUファン電源装置(スマートフ ァン 機能を搭載 )

システムファ ンヘ ッダ x1 システムファ ン電 源装置

CMOSクリアヘッダ x1

USBコネク タ x2

電源コネクタ (24 ピン) x1

電源コネクタ (4ピン) x1

プリンタポー トコ ネクタ x1 各コネ クタは1つのプリ ンタポ ートをサポ ートします

シリアルポー トコ ネクタ x1

PS/2キーボード x1

PS/2マウス x1

背面パネル

I/O

ボードサイ

ズ

特殊機能 RAID 0 / 1 のサポート

OSサポー ト Windows XP / Vista / 7

VGAポート x1

LANポート x1

USBポート x4

オーディオジ ャッ ク x3

170 mm (幅) X 235 mm (高さ)

各コネクタは 2つのフロ ントパネル USBポートをサ ポートし

ます

Biostarは事前の サポートな しにOSサ ポー トを追加ま たは削

除する権利を 留保 します。

MCP6PB M2+

2009/09/18

43