Biostar AM1MH, AM1MD, AM1ML Quick Start Manual

AM1MH / AM1MD / AM1ML

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents
here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.

Dichiarazione di conformità
sintetica

Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002

Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive

2004/108/CE, 2006/95/CE e
1999/05/CE

quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives

2004/108/CE, 2006/95/CE and
1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction.......................................... 1

1.1 Before You Start ................................................................................1

1.2 Package Checklist ............................................................................1

1.3 Motherboard Specifications.............................................................2

1.4 Rear Panel Connectors....................................................................3

1.5 Motherboard Layout..........................................................................4

Chapter 2: Hardware Installation ........................... 5

2.1 Install Central Processing Unit (AM1 Socket)............................... 5

2.2 Install a Heatsink...............................................................................6

2.3 Connect Cooling Fans...................................................................... 6

2.4 Install System Memory.....................................................................8

2.5 Expansion Slots.................................................................................9

2.6 Jumper Setting ................................................................................10

2.7 Headers & Connectors...................................................................11

Chapter 3: UEFI BIOS & Software ........................ 15

3.1 UEFI BIOS Setup............................................................................15

3.2 BIOS Update.................................................................................... 15

3.3 Software............................................................................................19

Chapter 4: Useful Help ......................................... 22

4.1 Driver Installation.............................................................................22

4.2 Extra Information.............................................................................23

4.2 AMI BIOS Beep Code.....................................................................24

4.3 Troubleshooting...............................................................................24

Appendix: SPEC In Other Languages .................... 25

Arabic.....................................................................................................................25

French ...................................................................................................................26

German .................................................................................................................27

Italian ..................................................................................................................... 28

Japanese...............................................................................................................29

Polish.....................................................................................................................30

Portuguese ...........................................................................................................31

Russian .................................................................................................................32

Spanish.................................................................................................................. 33

AM1MH / AM1MD / AM1ML

1

CHAPTER 1: INTRODUCTION

1.1 Before You Start

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with sufficient

lighting.

 Always disconnect the computer from power outlet before

operation.

 Before you take the motherboard out from anti-static bag,

ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.

 Avoid touching the components on motherboard or the rear

side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the case after

installation. Loose parts will cause short circuits which may
damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be 0 to

45 degrees Celsius.

 To avoid injury, be careful of:

Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit

1.2 Package Checklist

; Serial ATA Cable x2
; Rear I/O Panel for ATX Case x1
; Installation Guide x1
; Fully Setup Driver DVD x1

Note: The package contents may be different due to the sales region or models in which it was sold.
For more information about the standard package in your region, please contact your dealer or sales
representative.

Motherboard Manual

2

1.3 Motherboard Specifications

Specifications

CPU Support

AMD "Kabini" Athlon/Sempron APUs, AM1 Socket
* Please refer to www.biostar.com.tw for CPU support list.

Memory

Supports Single Channel DDR3 1333/ 1600 (*DDR3 1600 depends on CPU)
2 x DDR3 DIMM Memory Slot, Max. Supports up to 16 GB Memory
Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3 module
* Please refer to www.biostar.com.tw

for Memory support list.

Storage 2x SATA 6Gb/s Connector, Supports Native IDE, AHCI Mode

LAN

AM1MH / AM1MD:
Realtek RTL 8111G, 10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex
capability
AM1ML:
Realtek RTL 8106E, 10/ 100 Mb/s auto negotiation, Half / Full duplex
capability

Audio Codec ALC662, 5.1 Channels, High Definition Audio

USB

2x USB 3.0 port (2 on rear I/Os)
6x USB 2.0 port (2 on rear I/Os and 4 via internal headers)

Expansion Slots

1x PCIe 2.0 x16 Slot (x4)
1x PCIe 2.0 x1 Slot

Rear I/Os

1x PS/2 Mouse
1x PS/2 Keyboard
1x HDMI Port (AM1MH)
1x DVI-D (AM1MD)
1x VGA Port
1x LAN port
2x USB 2.0 Port
2x USB 3.0 Port
3x Audio Jack

Internal I/Os

2x SATA 6.0Gb/s Connector
2x USB 2.0 Header (each header supports 2 USB 2.0 ports)
1x 4-Pin Power Connector
1x 24-Pin Power Connector
1x CPU Fan Connector
1x System Fan Connector
1x Front Panel Header
1x Front Audio Header
1x Clear CMOS Header
1x Printer Port Header
1x Serial Port Header

Form Factor Micro-ATX Form Factor, 191 mm x 170 mm

OS Support

Windows XP / 7 / 8 / 8.1
Biostar reserves the right to add or remove support for any OS with or without
notice.

AM1MH / AM1MD / AM1ML

3

1.4 Rear Panel Connectors

AM1MH

AM1MD

AM1ML

Note 1: Since the audio chip supports High Definition Audio Specification, the function of

each audio jack can be defined by software. The input / output function of each audio jack
listed above represents the default setting. However, when connecting external microphone
to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.

Note 2: Maximum resolution:

HDMI: 1920 x 1080 @60Hz
DVI-D: 1920 x 1200 @60Hz
VGA: 1920 x 1200 @60Hz

Motherboard Manual

4

1.5 Motherboard Layout

Note: ■ represents the 1st pin.

AM1MH / AM1MD / AM1ML

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (AM1 Socket)

Step 1: Locate the CPU socket on the motherboard

Step 2: Pull the socket locking out from the socket and then raise the lever up to

a 90-degree angel.

Step 3: Look for the triangular cut edge on socket, and the golden dot on CPU

should point forwards this triangular cut edge. The CPU will fit only in the
correct orientation.

Motherboard Manual

6

Step 4: Hold the CPU down firmly, and then close the lever to locked the position

2.2 Install a Heatsink

The CPU might equip with two different types of heatsink. For proper installation,
please kindly refer to the installation manual of your heatsink.

Note: Do not forget to connect the CPU fan connector.

AM1MH / AM1MD / AM1ML

7

2.3 Connect Cooling Fans

These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different according to the fan manufacturer. Connect the fan
cable to the connector while matching the black wire to pin#1.

CPU_FAN: CPU Fan Header

Pin Assignment

1 Ground
2 Voltage Fan
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)

SYS_FAN: System Fan Header

Pin Assignment

1 Ground
2 +12V
3 FAN RPM rate sense

Note: CPU_FAN, SYS_FAN support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

8

2.4 Install System Memory

A. DDR3 Modules

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM

on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining clips

snap back in place and the DIMM is properly seated.

Note1: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

B. Memory Capacity

DIMM Socket Location

DDR3 Module

Total Memory Size

DDR3_A1 512MB/1GB/2GB/4GB/8GB
DDR3_A2 512MB/1GB/2GB/4GB/8GB

Max is 16GB.

AM1MH / AM1MD / AM1ML

9

2.5 Expansion Slots

PEX16_1: PCI-Express Gen2 x4 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 2GB/s per direction; 4GB/s in total.

PEX1_1: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total

Install an Expansion Card

You can install your expansion card by following steps:

1. Read the related expansion card's instruction document before
install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket
from the computer.

3. Place a card in the expansion slot and press down on the card until it
is completely seated in the slot.

4. Secure the card’s metal bracket to the chassis back panel with a
screw.

5. Replace your computer's chassis cover.

6. Power on the computer, if necessary, change BIOS settings for the
expansion card.

7. Install related driver for the expansion card.