Biostar A960GL+ Setup Manual

A960G+/A960GL+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Dichiarazione di conformità
sintetica

Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002

Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive

2004/108/CE, 2006/95/CE e
1999/05/CE

quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives

2004/108/CE, 2006/95/CE and
1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction.......................................... 1

1.1 Before You Start ................................................................................1

1.2 Package Checklist.............................................................................1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout ........................................................................4

Chapter 2: Hardware Installation ........................... 5

2.1 Installing Central Processing Unit (CPU) ....................................... 5

2.2 FAN Headers......................................................................................7

2.3 Installing System Memory ................................................................8

2.4 Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup.................... 13

3.1 How to Setup Jumpers ....................................................................13

3.2 Detail Settings.................................................................................. 13

Chapter 4: RAID Functions ................................... 17

4.1 Operating System............................................................................17

4.2 Raid Arrays......................................................................................17

4.3 How RAID Works.............................................................................17

Chapter 5: Useful Help ......................................... 20

5.1 Driver Installation Note .................................................................20

5.2 Software............................................................................................ 21

5.3 Extra Information ........................................................................... 25

5.4 Troubleshooting...............................................................................27

Appendix: SPEC In Other Languages .................... 28

German .................................................................................................................28

French....................................................................................................................30

Italian.................................................................................................................... 32

Spanish ..................................................................................................................34

Portuguese............................................................................................................ 36

Polish .....................................................................................................................38

Russian ..................................................................................................................40

Arabic .................................................................................................................... 42

Japanese................................................................................................................ 44

A960G+/A960GL+

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver DVD X 1 (full version manual files inside)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

Socket AM3 / AM3+

AMD Sempron/Athlon II / Phenom II /FX

processors (Maximum Watt: 95W)

AMD 64 Architecture enables 32 and 64 bit computing

Supports Hyper Transport 3.0

FSB

Support Hyper Transport 3.0

Supports up to 4.4 GT/s Bandwidth

Chipset

AMD 760G

AMD SB710

Super I/O

ITE 8728

Provides the most commonly used

legacy Super I/O functionality

Low Pin Count Interface

Environment Control initiatives

H/W Monitor

ITE's "Smart Guardian" function

Main

Memory

DDR3 DIMM Slots x 2

Max Memory Capacity 16GB

Each DIMM supports 512MB/1GB/

2GB/4GB/8GB DDR3

Dual Channel Mode DDR3 memory module

Supports DDR3 800/1066/1333/1600(OC)/1866(OC

for AM3+ CPU only)

Registered DIMM and ECC DIMM is not supported

Graphics

Integrated in AMD 760G Chipset Max Shared Video Memory is 512MB

SATA II

Integrated Serial ATA Controller

Data transfer rates up to 3 Gb/s

SATA Version 2.0 specification compliant

LAN

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

10 / 100 / 1000 Mb/s auto negotiation

10 / 100 Mb/s auto negotiation

Sound

ALC662

5.1 channels audio out

High Definition Audio

PCI Express X16 slot x1 Supports PCI-E X16 expansion card

Slots

PCI slot x1 Supports PCI expansion cards

SATA Connector x4 Each connector supports 1 SATA device

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

On Board

Connectors

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

A960G+/A960GL+

3

SPEC

System Fan Header x1 System Fan Power supply

CMOS Clear Jumper x1 Restore CMOS data to factory default setting

USB Connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 Ethernet cable

Connect to USB devices

Provide Audio-In/Out and microphone connection

Board Size

182 mm(W) x 225 mm(L)

Special

Features

RAID 0 / 1 / 10 support

OS Support

Windows XP / Vista / 7

Biostar reserves the right to add or remove support for

any OS With or without notice.

1.4 REAR PANEL CONNECTORS

PS/2
Mouse

PS/2
Keyboard

USBX2USBX2

LAN

VGA

Line In/
Surround

Line Out

Mic In 1/
Bass/ Center

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

Note: represents the 1■

st

pin.

A960G+/A960GL+

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.

Motherboard Manual

6

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the
installation.

Note:

1. This MB is designed for AMD 95W AM3/AM3+ CPU, pleases check the CPU TDP
spec before you install it on MB AM3+ CPU TDP spec from below weblink:

http://www.amd.com/us/products/desktop/processors/amdfx/Pages/amdfx-model­number-comparison.aspx

2. AMD’s product warranty does not cover damage caused by overclocking (even
when overclocking is enabled via AMD OverDrive software).

http://www.amd.com/us/products/desktop/processors/amdfx/Pages/amdfx.aspx

3. Due to the AMD AM3+ CPU designation, we strongly recommend you use AMD
original box CPU fan and add an extra system fan inside the chassis.

A960G+/A960GL+

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different due to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

CPU_FAN1: CPU Fan Header

Pin

Assignment

1 Ground
2 +12V
3

FAN RPM rate sense

4 Smart Fan Control

(By Fan)

SYS_FAN1: System Fan Header

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate sense

Note:

The CPU_FAN1 supports 4-pin head connector. The SYS_FAN1 supports 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

A960G+/A960GL+

9

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

Note:

If the DIMM does not go in smoothly, do not force it. Pull it all the way out and
try again.

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Memory

Size

DDR3_A1 512MB/1GB/2GB/4GB/8GB

DDR3_B1 512MB/1GB/2GB/4GB/8GB

Max is 16GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

DDR3_A1

DDR3_B1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it
satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

Pin Assignment

1 +12V
2 +12V
3 Ground
4 Ground

A960G+/A960GL+

11

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

Note:

Before power on the system, please make sure that both ATXPWR1 and ATXPWR2
connectors have been plugged-in.

Motherboard Manual

12

PEX16_1: PCI-Express X16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

PCI1: Peripheral Component Interconnect Slot

This motherboard is equipped with 1 standard PCI slot. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

A960G+/A960GL+

13

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2N/A 10N/A

N/A

3 N/A 11 N/A N/A
4 Speaker

Speaker
Connector

12 Power LED (+)
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)

Hard drive
LED

14 Power LED (-)

Power LED

7 Ground 15 Power button
8 Reset control

Reset button

16 Ground

Power-on button

Motherboard Manual

14

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Pin

Assignment

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 NC

10 Key

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10 Jack Sense

A960G+/A960GL+

15

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

Motherboard Manual

16

JCMOS1: Clear CMOS Jumper

Placing the jumper on pin2-3 allows user to restore BIOS safe setting and
CMOS data. Pease carefully follow the procedures to avoid damaging the
motherboard.

13

Pin 1-2 Close:

Normal Operation
(default).

13

Pin 2-3 Close:

Clear CMOS data.

Clear CMOS Procedures:※

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Optimal Defaults and save settings in CMOS.

A960G+/A960GL+

17

CHAPTER 4: RAID FUNCTIONS

4.1 O

PERATING SYSTEM

z Supports Windows XP, Windows Vista, and Windows 7.

4.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.
RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment.
This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

- Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.

- Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.

- Benefits: provides increased data throughput, especially for large files.
No capcity loss penalty for parity.

- Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.

- Fault Tolerance: No.

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Motherboard Manual

18

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.

RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.

Features and Benefits

- Drives: Minimum 2, and maximum is 2.

- Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

- Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.

- Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.

- Fault Tolerance: Yes.

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

A960G+/A960GL+

19

RAID 10:

RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.

Features and Benefits

- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.

- Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.

- Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.

- Fault Tolerance: Yes.

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Motherboard Manual

20

CHAPTER 5: USEFUL HELP

5.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver DVD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver DVD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
DVD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html

A960G+/A960GL+

21

5.2 SOFTWARE

Installing Software

1. Insert the Setup DVD to the optical drive. The drivers installation
program would appear if the Autorun function has been enabled.

2. Select Software Installation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this utility, please set Outlook Express as your default e-mail client application program.

This block will show
th e info rmat ion wh ich
wou ld be co llec ted i n
the mail.

Pro vide t he e- mail
address that you would
like to send the copy to.

Pro vide the na me of
the power supply
manufacturer and the
model no.

Send the mail out .

Sav e thes e info rmat ion t o a .txt file

Exit this dialog .

Select your area or
the area close to you.

*

Pro vid e th e name of
the memory module
manufact urer.

*

Describe condition
of your system.

*

*

represent s i mportant
in forma tion t hat y ou
must provide. Without
this information, you may
not be able to send out
the mail.

Motherboard Manual

22

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php

for getting

our contact information.

A960G+/A960GL+

23

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

Update BIOS

with a BIOS fil

e

Show current BIO S informati on

Save current BIOS

to a .bin file

Update BIOS

from the Internet

<Backup BIOS>

Once click on this button, the saving

dialog will show. Choose the

position to save file and enter file

name. (We recommend that the file

name should be English/number

and no longer than 7 characters.)

Then click Save.

Motherboard Manual

24

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.

A960G+/A960GL+

25

5.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

Motherboard Manual

26

BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

partition.

z Shutting down or resetting the system while updating the BIOS will lead to

system boot failure.

A960G+/A960GL+

27

5.4 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

Review system’s equipment. Make sure
correct information is in setup.

System cannot boot after user installs a
second hard drive.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

Motherboard Manual

28

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Spezifikationen

CPU

Sockel AM3 / AM3+

AMD Sempron/Athlon II / Phenom II

/FX Prozessoren (Maximales Watt:

95W)

Die AMD 64-Architektur unterstützt eine 32-Bit- und

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 3.0

FSB

Unterstützt Hyper Transport 3.0 mit

einer Bandbreite von bis zu 4.4 GT/s

Chipsatz

AMD 760G

AMD SB710

Super E/A

ITE8728

Bietet die häufig verwendeten alten

Super E/A-Funktionen.

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

Arbeitsspeich

er

DDR3 DIMM-Steckplätze x 2

Max. 16GB Arbeitsspeicher

Jeder DIMM unterstützt 512MB/1GB/

2GB/4GB/8GB DDR3.

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 800/1066/1333/1600(OC)/1800(OC

für AM3-CPU-only)

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Grafik

Integrierter AMD 760G-Chipsatz Max. 512MB gemeinsam benutzter Videospeicher

SATA

Integrierter Serial ATA-Controller

Datentransferrate bis zu 3 Gb/s

Konform mit der SATA-Spezifikation Version 2.0.

LAN

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

10 / 100 / 1000 Mb/s auto negotiation

10 / 100 Mb/s auto negotiation

HD

Audio-Unters

tützung

ALC662

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

PCI Express X16 Steckplatz x1

Steckplätze

PCI-Steckplatz x1

A960G+/A960GL+

29

Spezifikationen

SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfter-Sockel x1

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan-Funktion)

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-Sockel x1

USB-Anschluss x2

Jeder Anschluss unterstützt 2

Fronttafel-USB-Anschlüsse

Stromanschluss (24-polig) x1

Stromanschluss (4-polig) x1

Onboard-Ans

chluss

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Rückseiten-E

/A

PS/2-Tastatur x1

PS/2-Maus x1

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

Platinengröß

e

182 mm (B) X 225 mm (L)

Sonderfunkti

onen

Unterstützt RAID 0 / 1 / 10

OS-Unterstü

tzung

Windows XP / Vista / 7

Biostar behält sich das Recht vor, ohne Ankündigung die

Unterstützung für ein Betriebssystem hinzuzufügen

oder zu entfernen.

Motherboard Manual

30

FRENCH

SPEC

UC

Socket AM3 / AM3+

Processeurs AMD Sempron/Athlon II /

Phenom II /FX (Watt maximum : 95W)

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en charge Hyper Transport 3.0

Bus frontal

Prend en charge Hyper Transport 3.0

jusqu'à une bande passante de 4.4 GT/s

Chipset

AMD 760G

AMD SB710

Super E/S

ITE 8728

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Interface à faible compte de broches

Initiatives de contrôle environnementales,

Moniteur de matériel

Fonction "Gardien intelligent" de l'ITE

Mémoire

principale

Fentes DDR3 DI MM x 2

Capacité mémoire maximale de 16Go

Chaque DIMM prend en charge des DDR3

de 512Mo/1Go/2Go/4Go/8Go

Module de mémoire DDR3 à mode à double voie

Prend en charge la DDR3

800/1066/1333/1600(OC)/1866(OC pour les

processeurs AM3 uniquement)

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

Graphiques

Integré dans la chipset AMD 760G Mémoire vidéo partagée maximale de 512 Mo

SATA

Contrôleur Serial ATA intégré

Taux de transfert jusqu'à 3 Go/s.

Conforme à la spécification SATA Version 2.0

LAN

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

10 / 100 / 1000 Mb/s négociation automatique

10 / 100 Mb/s négociation automatique

Prise en

charge

audio HD

ALC662

Sortie audio à 5.1 voies

Prise en charge de l'audio haute définition

Fente PCI Express X16 x1

Fentes

Fente PCI x1

Connecteur

embarqué

Connecteur SATA x4

Chaque connecteur prend en charge 1 périphérique

SATA

A960G+/A960GL+

31

SPEC

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Embase de ventilateur UC x1

Alimentation électrique du ventilateur UC (avec

fonction de ventilateur intelligent)

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x2

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Connecteur d'alimentation x1

(24 broches)

Connecteur d'alimentation x1

(4 broches)

Connecteur de Port d'imprimante x1

Chaque connector prend en charge 1 Port

d'imprimante

E/S du

panneau

arrière

Clavier PS/2 x1

Souris PS/2 x1

Port VGA x1

Port LAN x1

Port USB x4

Fiche audio x3

Dimension

s de la

carte

182 mm (l) X 225 mm (H)

Fonctionnal

ités

spéciales

Prise en charge RAID 0 / 1 / 10

Support SE

Windows XP / Vista / 7

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

Motherboard Manual

32

ITALIAN

SPECIFICA

CPU

Socket AM3 / AM3+

Processori AMD Sempron/Athlon II /

Phenom II /FX (Watt massimo: 95W)

L’architettura AMD 64 abilita la computazione 32

e 64 bit

Supporto di Hyper Transport 3.0

FSB

Supporto di HyperTransport 3.0 fino a

4.4 GT/s di larghezza di banda

Chipset

AMD 760G

AMD SB710

Super I/O

ITE 8728

Fornisce le funzionalità legacy Super

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Funzione "Smart Guardian" di ITE

Memoria

principale

Alloggi DIMM DDR3 x 2

Capacità massima della memoria 16GB

Ciascun DIMM supporta DDR3

512MB/1GB/2GB/4GB/8GB

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3

800/1066/1333/1600(OC)/1800(OC per CPU

AM3 solo)

DIMM registrati e DIMM ECC non sono supportati

Grafica

Integrata nel Chipset AMD 760G La memoria video condivisa massima è di 512 MB

SATA

Controller Serial ATA integrato

Velocità di trasferimento dei dati fino a 3 Gb/s.

Compatibile specifiche SATA Versione 2.0.

LAN

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

Negoziazione automatica 10 / 100 / 1000 Mb/s

Negoziazione automatica 10 / 100 Mb/s

Supporto

audio HD

ALC662

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

Alloggio PCI Express X16 x1

Alloggi

Alloggio PCI x1

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Connettore pannello frontale x1 Supporta i servizi del pannello frontale

Connettori

su scheda

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

A960G+/A960GL+

33

SPECIFICA

Collettore ventolina CPU x1

Alimentazione ventolina CPU (con funzione Smart

Fan)

Collettore ventolina sistema x1 Alimentazione ventolina di sistema

Collettore cancellazione CMOS x1

Connettore USB x2

Ciascun connettore supporta 2 porte USB

pannello frontale

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x1

(4 pin)

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

I/O

pannello

posteriore

Tastiera PS/2 x1

Mouse PS/2 x1

Porta VGA x1

Porta LAN x1

Porta USB x4

Connettore audio x3

Dimension

i scheda

182 mm (larghezza) x 225 mm

(altezza)

Caratterist

iche

speciali

Supporto RAID 0 / 1 / 10

Sistemi

operativi

supportati

Windows XP / Vista / 7

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

Motherboard Manual

34

SPANISH

Especificación

CPU

Conector AM3 / AM3+

Procesadores AMD Sempron/Athlon II /

Phenom II /FX (Vatio máximo: 95W)

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

Soporta las tecnologías Hyper Transport 3.0

FSB

Admite HyperTransport 3.0 con un ancho

de banda de hasta 4.4 GT/s

Conjunto

de chips

AMD 760G

AMD SB710

Súper E/S

ITE 8728

Le ofrece las funcionalidades heredadas

de uso más común Súper E/S.

Interfaz de cuenta Low Pin

Iniciativas de control de entorno,

Monitor hardware

Función "Guardia inteligente" de ITE

Memoria

principal

Ranuras DIMM DDR3 x 2

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de

512MB/1GB/2GB/4GB/8GB

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800/1066/1333/1600(OC)/1866(OC

para CPU AM3 solamente)

No admite DIMM registrados o DIMM compatibles con

ECC

Gráficos

Integrados en el conjunto de chips AMD

760G

Memoria máxima de vídeo compartida de 512 MB

SATA

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3 Gb/s.

Compatible con la versión SATA 2.0.

Red Local

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

Negociación de 10 / 100 / 1000 Mb/s

Negociación de 10 / 100 Mb/s

Soporte de

sonido HD

ALC662

Salida de sonido de 5.1 canales

Soporte de sonido Alta Definición

Ranura PCI Express X16 X1

Ranuras

Ranura PCI X1

Conector SATA X4 Cada conector soporta 1 dispositivos SATA

Conectores

en placa

Conector de panel frontal X1 Soporta instalaciones en el panel frontal

A960G+/A960GL+

35

Especificación

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector soporta 2 puertos USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Panel

trasero de

E/S

Teclado P S/ 2 X1

Ratón PS/2 X1

Puerto VGA X1

Puerto de red local X1

Puerto USB X4

Conector de sonido X3

Tamaño d e

la placa

182 mm. (A) X 225 Mm. (H)

Funciones

especiales

Admite RAID 0 / 1 / 10

Soporte de

sistema

operativo

Windows XP / Vista / 7

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

Motherboard Manual

36

PORTUGUESE

ESPECIFICAÇÕES

CPU

Socket AM3 / AM3+

Processadores AMD Sempron/Athlon II /

Phenom II /FX (Watt máximo: 95W)

A arquitectura AMD 64 permite uma computação de 32

e 64 bits

Suporta as tecnologias Hyper Transport 3.0

FSB

Suporta a tecnologia HyperTransport 2.0

com uma largura de banda até 4.4 GT/s

Chipset

AMD 760G

AMD SB710

Especificaç

ão Super

I/O

ITE 8728

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Iniciativas para controlo do ambiente

Monitorização do hardware

Função "Smart Guardian" da ITE

Memória

principal

Ranhuras DIMM DDR3 x 2

Capacidade máxima de memória: 16GB

Cada módulo DIMM suporta uma

memória DDR3 de 512MB/1GB/

2GB/4GB/8GB

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3

800/1066/1333/1600(OC)/1866(OC para o CPU AM3

só)

Os módulos DIMM registados e os DIMM ECC não são

suportados

Placa

gráfica

Integrada no chipset AMD 760G Memória de vídeo máxima partilhada: 512 MB

SATA

Controlador Serial ATA integrado

Velocidades de transmissão de dados até 3 Gb/s.

Compatibilidade com a especificação SATA versão 2.0.

LAN

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

Auto negociação de 10 / 100 / 1000 Mb/s

Auto negociação de 10 / 100 Mb/s

Suporte

para áudio

de alta

definição

ALC662

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

Ranhura PCI Express X16 x1

Ranhuras

Ranhura PCI x1

Conectores

Conector SATA x4 Cada conector suporta 1 dispositivo SATA

A960G+/A960GL+

37

ESPECIFICAÇÕES

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áudio frontal x1 Suporta a função de áudio no painel frontal

Conector da ventoinha da CPU x1

Alimentação da ventoinha da CPU (com a função Smart

Fan)

Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1

Conector USB x2 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 pinos)

na placa

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Entradas/S

aídas no

painel

traseiro

Teclado P S/ 2 x1

Rato PS/2 x1

Porta VGA x1

Porta LAN x1

Porta USB x4

Tomada de áudio x3

Ta ma n ho

da placa

182 mm (L) X 225 mm (A)

Característi

cas

especiais

Suporta as funções RAID 0 / 1 / 10

Sistemas

operativos

suportados

Windows XP / Vista / 7

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

aviso prévio.

Motherboard Manual

38

POLISH

SPEC

Procesor

Socket AM3 / AM3+

AMD Sempron/Athlon II / Phenom II /FX

Procesory (Maksymalny Watt: 95W)

Architektura AMD 64 umożliwia przetwarzanie 32 i 64

bitowe

Obsługa Hyper Transport 3.0

FSB

Obsługa HyperTransport 3.0 o szerokości

pasma do 4.4 GT/s

Chipset

AMD 760G

AMD SB710

Pamięć

główna

Gniazda DDR3 DIMM x 2

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obsługuje moduły

512MB/1GB/2GB/4GB/8GB DDR3

Moduł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 800/1066/1333/1600(OC)/1866(OC

dla procesorów AM3 tylko)

Brak obsługi Registered DIMM oraz ECC DIMM

Super I/O

ITE 8728

Zapewnia najbardziej powszechne

funkcje Super I/O.

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Monitor H/W

Funkcja ITE "Smart Guardian"

Grafika

Zintegrowana w chipsecie AMD 760G

Maks. wielkość współdzielonej pamięci video wynosi

512 MB

SATA

Zintegrowany kontroler Serial ATA

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

LAN

Realtek RTL 8111F (A960G+), 10/ 100/ 1000 Mb/s z automatyczną negocjacją szybkości

Realtek RTL 8105E (A960GL+), 10/ 100 Mb/s z automatyczną negocjacją szybkości

Obsługa

audio HD

ALC662

5.1 kanałowe wyjście audio

Obsługa High-Definition Audio

Gniazdo PCI Express X16 x1

Gniazda

Gniazdo PCI x1

Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Złącza

wbudowan

e

Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim

A960G+/A960GL+

39

SPEC

Złącze główkowe wentylatora procesora

x1

Zasilanie wentylatora procesora (z funkcją Smart Fan)

Złącze główkowe wentylatora

systemowego x1

Zasilanie wentylatora systemowego

Złącze główkowe kasowania CMOS x1

Złącze USB x2

Każde złącze obsługuje 2 porty USB na panelu

przednim

Złącze zasilania (24 pinowe) x1

Złącze zasilania (4 pinowe) x1

Złącze Port drukarki x1 Każde złącze obsługuje 1 Port drukarki

Back Panel

I/O

Klawiatura PS/2 x1

Mysz PS/2 x1

Port VGA x1

Port LAN x1

Port USB x4

Gniazdo audio x3

Wymiary

płyty

182 mm (S) X 225 mm (W)

Funkcje

specjalne

Obsługa RAID 0 / 1 / 10

Obsluga

systemu

operacyjne

go

Windows XP / Vista / 7

Biostar zastrzega sobie prawo dodawania lub

odwoływania obsługi dowolnego systemu

operacyjnego bez powiadomienia.

Motherboard Manual

40

RUSSIAN

СПЕЦ

CPU
(централь

ный

процессор

)

Гнездо AM3 / AM3+

Процессоры AMD Sempron/Athlon II /

Phenom II /FX (Максимальный ватт:

95W)

Архитектура AMD 64 разрешать обработка данных

на 32 и 64 бит

Поддержка Hyper Transport 3.0

FSB

Поддержка HyperTransport 3.0 с

пропускной способностью до 4.4 GT/s

Набор
микросхем

AMD 760G

AMD SB710

Основная
память

Слоты DDR3 DIMM x 2

Максимальная ёмкость памяти 16ГБ

Каждый модуль DIMM поддерживает

512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3

Модуль памяти с двухканальным режимом DDR3

Поддержка DDR3

800/1066/1333/1600(OC)/1866(OC для

процессоров AM3 только)

Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Super I/O

ITE 8728

Обеспечивает наиболее используемые

действующие функциональные

возможности Super I/O.

Интерфейс с низким количеством выводов

Инициативы по охране окружающей среды,

Аппаратный монитор

Функция ITE "Smart Guardian" (Интеллектуальная

защита)

Графика

Встроенная в набор микросхем AMD

760G

Максимальная совместно используемая видео

память составляет 512 МБ

SATA

Встроенное последовательное

устройство управления ATA

скорость передачи данных до 3 гигабит/с.

Соответствие спецификации SATA версия 2.0.

Локальная
сеть

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

Автоматическое согласование 10 / 100 / 10000 Мб/с

Автоматическое согласование 10 / 100 Мб/с

Звуковая

поддержка
жесткого
диска

ALC662

Звуковая поддержка High-Definition

5.1канальный звуковой выход

Слот PCI Express X16 x1

Слоты

Слот PCI x1

Разъём SATA x4 Каждый разъём поддерживает 1 устройство SATA

Встроенны
й разъём

Разъём на лицевой панели x1 Поддержка устройств на лицевой панели

A960G+/A960GL+

41

СПЕЦ

Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели

Контактирующее приспособление

вентилятора центрального

процессора x1

Источник питания для вентилятора центрального

процессора (с функцией интеллектуального

вентилятора)

Контактирующее приспособление

вентилятора системы x1

Источник питания для вентилятора системы

Открытое контактирующее

приспособление CMOS x1

USB-разъём x2

Каждый разъём поддерживает 2 USB-порта на

лицевой панели

Разъем питания (24 вывод) x1

Разъем питания (4 вывод) x1

Разъём Порт подключения

принтера x1

Каждый разъём поддерживает 1 Порт подключения

принтера

Задняя
панель
средств
ввода-выв
ода

Клавиатура PS/2 x1

Мышь PS/2 x1

Порт VGA x1

Порт LAN x1

USB-порт x4

Гнездо для подключения

наушников x3

Размер
панели

182 мм (Ш) X 225 мм (В)

Специальн
ые

техническ
ие

характери
стики

Поддержка RAID 0 / 1 / 10

Поддержк
а OS

Windows XP / Vista / 7

Biostar сохраняет за собой право добавлять или

удалять средства обеспечения для OS с или без

предварительного уведомления.

Motherboard Manual

42

ARABIC

تﺎﻔﺻاﻮﻤﻟا

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺑ ﺔﻴﺑﻮﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺟإ 32 و64 ﺖﺑ

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyper Transport و 3.0

ﺲﺒﻘﻣAM3 / AM3+

تﺎﺠﻟﺎﻌﻣAMD Sempron/Athlon II / Phenom II /FX

(طاو ىﻮﺼﻗ: 95و)

ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا

ﺔﻳﺰآﺮﻤﻟا

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺑ 3.0 4.4 GT/s

ﻞﻗﺎﻨﻟا ﻲﻣﺎﻣﻷا ﻲﺒﻧﺎﺠﻟا

AMD 760G

AMD SB710

ﺔﻋﻮﻤﺠﻣ ﺢﺋاﺮﺸﻟا

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗLow Pin Count Interface

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺟﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺔﻔﻴﻇو"Smart Guardian" ﻦﻣ ITE

ITE 8728

ﺔﻔﻴﻇو ﺮﻓﻮﺗSuper I/O ًﺎ ﻣ ا ﺪ ﺨﺘ ﺳا ﺮﺜآﻷا .

Super I/O

ةﺮآاذ ةﺪﺣوDDR3 ﻘﻟا ﺔﺟودﺰﻣةﺎﻨ

عﻮﻧ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 تﺎﻌﺳ

800/1066/1333/1600)OC( ﺎﺠﻴﻣ

ﺖﻳﺎﺑ/1866 (OC ل تﺎﺠﻟﺎﻌﻣ AM3 ﻂﻘﻓ)

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ﺔﺤﺘﻓDDR3 DIMM دﺪﻋ2

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ16 ﺖﻳﺎﺑ ﺎﺠﻴﺟ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM ﺗ عﻮﻧ ﻦﻣ ةﺮآاذ ﻢﻋﺪ DDR3 ﺔﻌﺳ

/512 ﺖﻳﺎﺑ ﺎﺠﻴﻣ

و1/و 2/و 4/و 8 ﺎﺠﻴﺟﺖﻳﺎﺑ

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮﻳﺪﻴﻔﻟا ﺔآﺮﺘﺸﻤﻟا 512 ﺎﺠﻴﻣ ﺖﻳﺎﺑ

ﻖﺋﺎﻗر ﻲﻓ ﺔﺠﻣﺪﻣ AMD 760G

ﺔﻗﺎﻄﺑ تﺎﻣﻮﺳﺮﻟا

ﻞﻘﻧ تﺎﻧﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼﺗ ﻰﻟإ 3 ﺖﺑﺎﺠﻴﺟ/ﺔﻴﻧﺎﺛ.

ﺔﻘﺑﺎﻄﻣ تﺎﻔﺻاﻮﻤﻟ SATA راﺪﺻﻹا 2.0.

ﻜﺤﺘﻣﻢ Serial ATA ﻞﻣﺎﻜﺘﻣ

SATA

ﺎﺠﻴﻣ / ﺔﻴﻧﺎﺛ ضوﺎﻔﺗ تارﺎﻴﺴﻟا 10/100/1000

ﺎﺠﻴﻣ / ﺔﻴﻧﺎﺛ ضوﺎﻔﺗ تارﺎﻴﺴﻟا 10/100

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

ﺔﻜﺒﺷ ﺔﻴﻠﺧاد

5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا

ﻦﻣ ﻒﻳﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

ALC662

ﻢﻋد تﻮﺼﻟا ﻲﻟﺎﻋ

ﻒﻳﺮﻌﺘﻟا

ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1

ﺔﺤﺘﻓPCI دﺪﻋ1

تﺎﺤﺘﻔﻟا

ةﺰﻬﺟأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳSATA

ﺬﻔﻨﻣSATA دﺪﻋ4

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪﻳ

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻣ دﺪﻋ1

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪﻳ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄﺳ

ﺔﺣﻮﻠﻟا

A960G+/A960GL+

43

تﺎﻔﺻاﻮﻤﻟا

ﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟ ﺔﻔﻴﻇو ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔ Smart Fan

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺻو دﺪﻋ1

مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟ

مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺻو دﺪﻋ1

ﺢﺴﻣ ﺔﻠﺻوCMOS دﺪﻋ1

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳUSBﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ

ﺬﻔﻨﻣUSB دﺪﻋ2

ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻣ)24سﻮﺑد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻣ)4سﻮﺑد( دﺪﻋ1

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻣ دﺪﻋ1

ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟPS/2 دﺪﻋ1

سوﺎﻣ PS/2 دﺪﻋ1

ﺬﻔﻨﻣVGA دﺪﻋ1

ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺷ ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻓﺎﻨﻣUSB دﺪﻋ4

تﻮﺻ ﺲﺒﻘﻣ ﺪﻋ3

ﺬﻓﺎﻨﻣ ﻞﺧد/جﺮﺧ

ﺔﺣﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

182 ﻢﻣ)ضﺮﻋ (X 225 ﻢﻣ)عﺎﻔﺗرا(

ﻢﺠﺣ ﺔﺣﻮﻠﻟا

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗRAID 0 / 1 / 10

ﺔﺻﺎﺧ ﺎﻳاﺰﻣ

ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺧﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ

رﺎﻄﺧإ نوﺪﺑ.

Windows XP / Vista / 7

ﻢﻋد ﺔﻤﻈﻧأ ﻞﻴﻐﺸﺘﻟا

Motherboard Manual

44

JAPANESE

仕様

CPU

Socket AM3 / AM3+

AMD Sempron/Athlon II / Phenom II /FX

プロセッサ (最高のワット: 95W)

AMD 64アーキテクチャでは、32ビットと64ビット計算が可

能です

ハイパートランスポート3.0とクールアンドクワイアットを

サポートします

FSB

4.4 GT/sのバンド幅までハイパートランスポ

ート3.0をサポートします

チップセッ

ト

AMD 760G

AMD SB710

メインメモ

リ

DDR3 DIMMスロット x 2

最大メモリ容量16GB

各DIMMは 512MB/1GB/2GB/4GB/8GB

DDR3をサポート

デュアル チャンネルモードDDR3メモリモジュール

DDR3 800/1066/1333/1600(OC)/1866（唯一のAM3

CPUのOC） をサポート

登録済みDIMMとECC DIMMはサポートされません

Super I/O

ITE 8728

もっとも一般に使用されるレガシーSuper I/O

機能を採用しています。

低ピンカウントインターフェイス

環境コントロールイニシアチブ、

H/Wモニター

ITEの「スマートガーディアン」機能

グラフィッ

クス

AMD 760Gチップセットに統合 最大の共有ビデオメモリは512MBです

SATA

統合シリアルATAコントローラ

最高3Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

LAN

Realtek RTL 8111F (A960G+)

Realtek RTL 8105E (A960GL+)

10 / 100 / 1000 Mb/秒のオートネゴシエーション

10 / 100 Mb/秒のオートネゴシエーション

HDオーディ

オのサポー

ト

ALC662

5.1チャンネルオーディオアウト

ハイデフィニションオーディオのサポート

PCI Express X16スロット x1

スロット

PCIスロット x1

SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします

オンボード

コネクタ

フロントパネルコネクタ x1 フロントパネル機能をサポートします

A960G+/A960GL+

45

仕様

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ x1 システムファン電源装置

CMOSクリアヘッダ x1

USBコネクタ x2

各コネクタは2つのフロントパネルUSBポートをサポートし

ます

電源コネクタ(24ピン) x1

電源コネクタ(4ピン) x1

プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします

背面パネル

I/O

PS/2キーボード x1

PS/2マウス x1

VGAポート x1

LANポート x1

USBポート x4

オーディオジャック x3

ボードサイ

ズ

182 mm (幅) X 225 mm (高さ)

特殊機能

RAID 0 / 1 / 10 のサポート

OSサポート

Windows XP / Vista / 7

Biostarは事前のサポートなしにOSサポートを追加または削

除する権利を留保します。

2013/01/15