BFT Cellula 50 User Manual

FOTOCELLULA

GB

PHOTOCELL

PHOTOCELLULE
PHOTOZELLE
FOTOCÉLULA
FOTOCÉLULA

D811286 ver. 03 20-07-06

CELLULA 50

ISTRUZIONI DI INSTALLAZIONE

INSTALLATION MANUAL

INSTRUCTIONS D’INSTALLATION

MONTAGEANLEITUNG

INSTRUCCIONES DE INSTALACION

INSTRUÇÕES DE INSTALAÇÃO

Via Lago di Vico, 44
36015 Schio (VI)
Tel.naz. 0445 696511
Tel.int. [phone]
Fax [phone]
Internet: www.bft.it
E-mail: [e-mail]

D811286_03

INSTALLATION MANUAL

Thank you for buying this product, our company is sure that you will
be more than satisfied with the product’s performance. The product is
supplied with a “Warnings” leaflet and an “Instruction booklet”. These
should both be read carefully as they provide important information about
safety, installation, operation and maintenance. This product complies with
the recognised technical standards and safety regulations. We declare
that this product is in conformity with the following European Directives:

73/23/EEC-89/336/EEC (and subsequent amendments).

1) GENERAL OUTLINE (Fig.1)
Cellula 50 Mod recessed photocell to be fitted externally, consisting of a

pair of transmitters and receivers having a double relay which is normally
energised, as provided for by the relevant standards.

2) TECHNICAL SPECIFICATIONS

er supply :15 - 30 V~

Pow
Absorbed power :6.85 VA
Max range :30m (reduced in case of fog / rain)
Relay contacts :1A at 24V~­Working temperature :-10°C to +70°C
Degree of protection :IP54

3) PHOTOCELL FITTING

The photocells should be installed between 40 and 60 cm in height,
in the following ways:

- In the case of a masonry pillar, dig a hole where to insert the plastic
container supplied, which is to be secured by concrete filling (fig. 1).

- In the case of an iron pillar, make a hole using a ø 60 cutter where
to insert the plastic container supplied. To secure the container,
make three ø 2.7 holes for fastening the three self-tapping screws
supplied (fig. 2).

- If there is no pillar or wall for the photocells to be secured to, request
the appropriate metal posts. The posts can be directly secured onto a
concrete base by means of three screw anchors (fig. 3).

) corrispondente al massimo allineamento.

6) MANUTENZIONE E DEMOLIZIONE
La manutenzione dell’impianto va fatta eseguire regolarmente da
parte di personale qualificato. I materiali costituenti l’apparecchiatura

e il suo imballo vanno smaltiti secondo le norme vigenti.

Le descrizioni e le illustrazioni del presente manuale non sono
impegnative. Lasciando inalterate le caratteristiche essenziali del
prodotto, la Ditta si riserva di apportare in qualunque momento le
modifiche che essa ritiene convenienti per migliorare tecnicamente,
costruttivamente e commercialmente il prodotto, senza impegnarsi
ad aggiornare la presente pubblicazione.

ENGLISH

Perfect alignment to the wall is ensured by the adjustment slots

provided in the base.

4) CONNECTION TO THE TERMINAL BOARD (Fig. 4)
Transmitter - Receiver
1-2 Power supply
3-4 Normally closed contact (When photocells are aligned the contact

opens).

3-5 Normally open contact (When photocells are aligned the contact

closes).

Warning! The installation must be carried out by qualified personnel.

5) PHOTOCELL ALIGNMENT

Correct alignment between the receiver and the transmitter is achieved
by adjusting the appropriate V (vertical) and O (horizontal) screws (fig.

5), until maximum luminosity of the internal L LED is obtained.
A voltameter can also be fitted to the two P pins to indicate maximum
voltage (3 V ) which corresponds to maximum alignment.

6) MAINTENANCE AND DEMOLITION
The maintenance of the system should only be carried out by
qualified personnel regularly. The materials making up the set and its

packing must be disposed of according to the regulations in force.

The descriptions and illustrations contained in the present manual
are not binding. The Company reserves the right to make any
alterations deemed appropriate for the technical, manufacturing
and commercial improvement of the product, while leaving the
essential product features unchanged, at any time and without
undertaking to update the present publication.