BFT Cellula 180 User Manual

D811667_02 09-02-10

8

027908 349569

FOTOCELLULA

PHOTOCELL

PHOTOCELLULE
LICHTSCHRANKE
FOTOCÉLULA
FOTOCEL

FOTOCÉLULA
ΦΤΟΚΥΤΤΑΡΟ
FOTOKOMÓRKA
ФОТОЭЛЕМЕНТ
FOTOBUŇKA
FOTOSEL

CELLULA 180

CELLULA 180

ISTRUZIONI DI INSTALLAZIONE

INSTALLATION MANUAL

INSTRUCTIONS D’INSTALLATION

MONTAGEANLEITUN

GİLERİ

Attenzione! Leggere attentamente le “Avvertenze” all’interno! Caution! Read “Warnings” inside carefully! Attention! Veuillez lire attentivement les Avertissements qui se trouvent à l’intérieur! Achtung! Bitte lesen Sie
aufmerksam die „Hinweise“ im Inneren! ¡Atención¡ Leer atentamente las “Advertencias” en el interior! Let op! Lees de “Waarschuwingen”tigre aan de binnenkant zorgvuldig! Atenção! Ler atentamente as “Instruções
“ que se encontram no interior! Προσοχή! ιαβάστε ε προσοχή τι “Προειδοποιήσει” στο εσωτερικό! Uwaga! Należy uważnie przecz ytać “Ostrzeżenia” w środku! Внимание! Внимательно прочтите находящиеся
внутри “Инструкции”!” Dikkat! İçinde bulunan “Uyarıları” dikkatle okuyunuz!

Thank you for choosing this product. The Firm is confident that its performance will meet your o perating
needs. Carefully read the “Instruction booklet” that comes with this product as it provides important
information regarding safety, installation, use and maintenance. This product meets recognized
technical standards and complies with safety provisions. We hereby confirm that it is in conformit y with
the following European directives: 2006/96/EEC, 2004/10 8/EEC.This is a type D device in accordance
with EN 12453 and it will only be in conformity with directive 98/37/EEC provided it is connected to a
control panel from the same manufacturer equipped with a test circuit that looks for faults in the safety
circuits.

WARNING!

When carrying out connection and installation operati ons always ref er to the current legislation i n force,
as well as to good technical principles.- making changes to the device or to the unit’s configuration
without consul-ting the manufacturer may result in hazardous situations.- To connect the relay contacts
to the fault test circuit, you must refer to the wiring diagrams of the tested devices given in the instruction
manual for the control unit being used.- if other devices using infrared beams (photocells) are present,
they may cause interference.

USING THE DEVICE

Keep areas that lead to the safety device clear of obstacles. More specifically, make sure that no
branches or shrubs break the beam emitted by the transmitter. If the safety device is triggered, no
resetting or re-enabling is required since the gate’s regular operation will be restored a uto matically.

MAINTENANCE AND SCRAPPING

When the device is connected to a control panel from the same manufacturer, provide d with a fault­finding circuit in safety circuits, it requires no maintenance, since testing is carried out automatically with
each manoeuvre (test intervals conforming to risk analysis or EN12453). In the case where the fault­finding circuit in safety circuits is not used, get qualified personnel to check the device function at
intervals not longer than 6 months. The materials making up the appliance and its packing must be
disposed of according to current regulations. In case of malfunction, request the assist ance of qualified
personnel. All adjustments, whether mechanical or electrical, must be carried out by authorized
personnel only in accordance with the safety rules and instructions issued by the manufacturer. If
excessive amounts of dirt build up on the surface of the photocell, clean the photocell lenses with a
cloth.

WARNING!

Correct operation is only ensured when the data c ontained in the present manual are observed. The
company is not to be held responsible for any damage resulting from failure to observe the install ation
standards and the instructions contained in the present manual. The descriptions and illustrations
contained in the present manual are not binding. The Company reserves the right to make any
alterations deemed appropriate for the technical, manufacturing and commercial improvement of the
product, while leaving the essential product f eatures unchange d, at any ti me and without undertaki ng to
update the present publication.