BFT ARES ULTRA BT A 1000, ARES ULTRA BT A 1500 Installation And User Manual

ISTRUZIONI D’USO E DI INSTALLAZIONE

INSTALLATION AND USER’S MANUAL

INSTRUCTIONS D’UTILISATION ET D’INSTALLATION

INSTALLATIONS-UND GEBRAUCHSANLEITUNG

INSTRUCCIONES DE USO Y DE INSTALACION

INSTALLATIEVOORSCHRIFTEN

ATTUATORE PER CANCELLI SCORREVOLI A CREMAGLIERA
ACTUATOR FOR RACK SLIDING GATES
ACTIONNEUR POUR PORTAILS COULISSANTS A CREMAILLERE
ANTRIEB FÜR ZAHNSTANGEN-SCHIEBETORE
SERVOMOTOR PARA CANCELAS CORREDERAS DE CREMALLERA

ACTUATOR VOOR SCHUIFHEKKEN MET TANDHEUGEL

Attenzione! Leggere attentamente le “Avvertenze” all’interno! Caution! Read “Warnings” inside carefully! Attention! Veuillez lire attentivement les Avertissements qui se trouvent à l’intérieur!

Achtung! Bitte lesen Sie aufmerksam die „Hinweise“ im Inneren! ¡Atención¡ Leer atentamente las “Advertencias”en el interior! Let op! Lees de “ Waarschuwingen” aan de binnenkant zorgvuldig!

D812201 00100_03 14-04-16

ARES ULTRA BT A 1000

ARES ULTRA BT A 1500

ULTRA

INSTALLAZIONE VELOCE-QUICK INSTALLATION-INSTALLATION RAPIDE
SCHNELLINSTALLATION-INSTALACIÓN RÁPIDA - SNELLE INSTALLATIE

2x0.75mm

2

3x1.5mm

2

RG58

3x1.5mm

2

3x1.5mm

2

5x0,75mm

2

2x1.5mm

2

Y

Y

A

C

C1

E

D1D

22mm + “X

”

> 25mm

B

> 10mm

1

2

MAX 7 mm

MAGNETO

3x0.5mm

2

1

2 3

PREDISPOSIZIONE TUBI, TUBE ARRANGEMENT

PRÉDISPOSITION DES TUYAUX, VORBEREITUNG DER LEITUNGEN,

DISPOSICIÓN DE TUBOS, VOORBEREIDING LEIDINGEN.

MONTAGGIO ACCESSORI TRASMISSIONE, MOUNTING DRIVE ACCESSORIES, MONTAGE ACCESSOIRES TRANSMISSION,
MONTAGE ANTRIEBSZUBEHÖR, MONTAJE DE ACCESORIOS TRANSMISIÓN, MONTAGE ACCESSOIRES OVERBRENGING.

FISSAGGIO STAFFE FINECORSA (DX E SX),
FASTENING LIMIT SWITCH BRACKETS (RH/LH),
FIXATION ÉTRIERS FIN DE COURSE (DRT ET GCH),
BEFESTIGUNG BÜGEL ANSCHLÄGE (RECHTS UND LINKS),
FIJACIÓN ABRAZADERAS FINAL DE CARRERA (DER. E IZQ.),
BEVESTIGING STANGEN AANSLAG (RECHTS EN LINKS).

MONTAGGIO MOTORE
MOUNTING THE MOTOR
MONTAGE MOTEUR
MONTAGE MOTOR
MONTAJE DEL MOTOR
MONTAGE MOTOR

PREDISPOSIZIONE FISSAGGIO MOTORE, PREPARATION FOR MOTOR MOUNTING,

AMÉNAGEMENT FIXATION MOTEUR, VORBEREITUNG MOTORBEFESTIGUNG,

DISPOSICIÓN FIJACIÓN DEL MOTOR, VOORBEREIDING BEVESTIGING MOTOR.

“X”=

Cremagliera, Rack,
Crémaillère, Zahnstange
Cremallera, Tandheugel

2 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

ENGLISH FRANÇAIS ESPAÑOL

NEDERLANDS

DEUTSCHITALIANO

F

AUX 3 = 0
AUX 3 = 2
AUX 3 = 3
AUX 3 = 4
AUX 3 = 5
AUX 3 = 6
AUX 3 = 7
AUX 3 = 8
AUX 3 = 9
AUX 3 = 10

AUX 0 = 0
AUX 0 = 2
AUX 0 = 3
AUX 0 = 4
AUX 0 = 5
AUX 0 = 7
AUX 0 = 8
AUX 0 = 9
AUX 0 = 10

AUX 0 = 6 AUX 3 = 1

21

24 V

SCA

!

24V

25W

20 21

AUX0

(MAX 1A)

20 21

26 27

!

F3 1,25A T

F1 1,6 AT (220-230V)

F1 3,15 AT (120V)

10L N 11 20 21 26 27 50 51 52 60 61 62 70 71 72 73 74 75

L

N

M1

+

-

AUX 3
(MAX 24V 1A)

24V ~ (-)

24V ~ (+)

24 VSafe

COM

IC 1

IC 2

NO

NO

SAFE 1

STOP
COM

FAULT 1

SAFE 2

FAULT 2

NC

NC

NC

S1

S2

S3

+

-

OK

24V~

JP3

24V

2

1

TX1

2

1

RX1

4
5

3

SAFE 1 = 0

24V

!

AUX 0
(MAX 1A)

24V

26 27 50 51

50 51

70 72

OPEN

CLOSE

S1

S2

+

S1

+

-

S2

-

X1

X1 X1

X1

OPEN

CLOSE STOP

STOP

**

G

Display + tasti programmazione,
Display plus programming keys,
Acheur et touches de programmation,
Display und Programmierungstasten,
Pantalla más botones de programación,
Display meerdere toetsen programmeur.

Connettore necorsa
Limit switch connector
Connecteur de n de course
Steckverbindung Endschalter
Conector nal de carrera
Connector eindaanslag

Connettore programmatore palmare,
Palmtop programmer connector,
Connecteur programmateur de poche,
Steckverbinder Palmtop-Programmierer,
Conector del programador de bolsillo,
Connector programmeerbare palmtop.

Sicurezze
Safety devices
Sécurités
Sicherheitsvorrichtungen
Dispositivos de seguridad
Veiligheden

Comandi / Commands
Commandes/Bedienelemente
Mandos/ Commando’s

Motore / Motor / moteur
Motor /Eindaanslag/Encoder

Alimentazione / Power supply
Alimentation / Stromversorgung
Alimentación /Voeding

Collegamento di 1 coppia di fotocellule non vericate,
Connection of 1 pair of non-tested photocells,
Connexion 1 paire photocellules no vériées,
Anschluss von einem Paar nicht überprüften Fotozellen,
Conexión de 1 par fotocélulas no comprobadas,
Aansluiting van 1 paar fotocellen anders dan “trusted device”.

**Con logica inversione direzione di apertura = 000 (DIR=DX) / **With reverse logic, opening direction = 000 (DIR=right)
** Avec logique inversion direction d’ouverture = 000 (DIR=DRT ) / **Mit Inversionslogik Ö nungsrichtung = 000 (DIR=rechts)
**Con lógica inversión dirección de apertura = 000 (DIR=DER) / **Met logica omkering openingsrichting = 000 (DIR=R)

Alimentazione accessori
Accessories power supply
Alimentation des accessoires
Stromversorgung Zubehör
Alimentación accesorios
Voeding accessoires

Connettore scheda opzionale,
Optional board connector,
Connecteur carte facultative,
Steckverbinder Zusatzkarte,
Conector de la tarjeta opcional,
Connector optionele kaart.

AUX

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500 - 3

D812201 00100_03

ENGLISH FRANÇAIS ESPAÑOL

NEDERLANDS

DEUTSCHITALIANO

language

dir

ITA

fra

deu

eng

esp

lh

rh

AR

preset

e

hidden button

release O 01

re otes

sr

ac

sc

ind

end

ar: automatic operation,

residential

sr: semiautomatic operation,

residential

ac: automatic operation,

commercial

Sc: semiautomatic operation,

commercial

Ind:dead man operation

lh

rh

desidered button

: motor installed on the left

: motor installed on the right

autoset

. . . . . .

o o

AUTO OPEN

AUTO CLOSE

MIN 1 - MAX 3

Exit Menù

Conrm/Switch
on display

Scroll up

Scroll down

SIMPLIFIED MENU (FIG.1)

x1

0---

10--

150- 1520 ok

*** Password entry.

Request with Protection Level logic set to 1, 2, 3, 4

***

PRESET

DEFAULT

ar sr ac sc ind

PARAMETERS

LOGIC

TCA 0 1 0 1 0 0

Step-by-step movement 0 1 0 1 0 0

Pre-alarm 0 0 0 1 1 0

Deadman 0 0 0 0 0 1

Block pulses during opening 0 0 0 1 1 0

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500 - 5

D812201 00100_03

K1

H I

K

L

N

J

M

CFZ CP

37

30

12

28

22

22

CVZ

28

60

6

40

KO OK

>100

22

65>25

2mm

160

270

110

300

65

200

Z18 Øp72

Z25 Øp100

22

40

N1

N2

Per cancello con peso no 500 Kg

For gate weighing up to 500 kg

Pour portail pesant jusqu’à 500 kg

Für Tor mit Gewicht von bis zu 500kg
Para cancela con peso de hasta 500 Kg
Voor poort met een gewicht tot 500 Kg

10 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

E

O

UNIDA

P

F3

F1

10L N 11 20 21 26 27 50 51 52 60 61 62 70 71 72 73 74 75

S1

S2

S3

+

-

OK

F3

F1

10L N 11 20 21 26 27 50 51 52 60 61 62 70 71 72 73 74 75

S1

S2

S3

+

-

OK

TX1 (PHOT)

RX1 (PHOT)

CC1

(BAR)

CC2

(BAR)

TX2 (PHOT)

RX2 (PHOT)

M2

SLAVE

M1

MASTER

B EBA 201 R01

50 51 52

CC2

70 71 72 73 74 75 76 77 78

SAFE 1 = 1
SAFE 2 = 7 (≥6)
SAFE 3 = 1

SAFE 2 SLAVE = SAFE 2 MASTER

50 51 52 6160

TX1 RX1

TX2

CC1

RX2

62 63 64 65 70 71 72 73 74 75 76 77 78

START

STOP

MAX 250m

B EBA 201 R01

70

8888

SCHEDA DI ESPANSIONE
EXPANSION BOARD
CARTE D’EXPANSION
ERWEITERUNGSKARTE

TARJETA DE EXPANSIÓN
UITBREIDINGSKAART

PROGRA MMATOR E PAL MARE UNIVERS ALE
UNIVER SAL PALMTOP PROGRA MMER
PROGRA MMAT EUR DE POCHE U NIVERSE
UNIVER SELLEN PALMTOPPR OGRAMMIER
PROGRA MADOR DE BOLS ILLO UNIVERSA L
PROGRA MMEERBARE U NIVERSELE PALMTOP

ESEMPIO APPLICAZIONE ANTE CONTRAPPOSTE CON 1 PHOT E 2 BAR  SAMPLE APPLICATION WITH OPPOSITE LEAVES WITH 1 PHOT AND 2 BAR

 EXEMPLE D’APPLICATION VANTAUX OPPOSÉS AVEC 1 PHOT ET 2 BAR  ANWENDUNGSBEISPIEL EINANDER ENTGEGENGESETZTE TORFLÜGEL

MIT 1 PHOT UND 2 BAR  VOORBEELD TOEPASSING TEGENOVERGESTELDE VLEUGELS MET 1 PHOT EN 2 BAR

PER IL COLLEGAMENTO DI PIÙ FOTOCELLULE FARE RIFERIMENTO ALLA FIG. S  TO CONNECT SEVERAL PHOTOCELLS, REFER TO FIG. S

POUR BRANCHER PLUSIEURS PHOTOCELLULES CONSULTEZ LA FIG. S  BITTE NEHMEN SIE FÜR DEN ANSCHLUSS MEHRERER FOTOZELLEN AUF FIG. S BEZUG.

PARA LA CONEXIÓN DE VARIAS FOTOCÉLULAS CONSULTAR LA FIG. S  VOOR HET VERBINDEN VAN MEERDERE FOTOCELLEN ZIE FIG. S

iNDIRIZZO = 0
address = 0
adresse = 0
adresse = 0
direccion = 0

modo seriale = 3
serial mode = 3
mode serie = 3
serieller modus = 3
modo seria = 3

iNDIRIZZO = 0
address = 0
adresse = 0
adresse = 0
direccion = 0

modo seriale = 2
serial mode = 2
mode serie = 2
serieller modus = 2
modo seria = 2

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

-

11

D812201 00100_03

Q

DIR= dK

1

2

ON ON

OFF OFF

S1

S2

S3

+

-

OK

ON ON

OFF OFF

S1

S2

S3

+

-

OK

70 71

COM

STOP

S1

S2

S3

+

-

OK

S1

S2

S3

+

-

OK

8888 rst

8

8888

. ...

R

1 2 3 4

65

!

<3s

+

DIR= sK

verso di apertura: destra
opening direction: right
sens de l’ouverture : droite
Önungsrichtung: rechts
sentido de apertura: derecha
openingsrichting: rechtsverso

Inversione direzione di aperura: 1
Open in other direction: 1
Inversion direction de l’ouverture: 1
Richtungsumkehrung Önung: 1
Inversión dirección de apertura: 1
Openingsrichting omdraaien: 1

- Nel passaggio di congurazione logica da apertura destra/sinistra, non invertire il collegamento originale del connettore JP10.

- When switching logic conguration from right to left opening, do not swap over the original connection of terminal JP10.

- Lors du changement de conguration logique de l’ouverture droite/gauche, n’inversez pas la connexion d’origine des bornes JP10.

- Invertieren Sie bei der Änderung der Kongurierung der Logik Önung rechts/links nicht den Originalanschluss der Steckverbindung JP10.

- En el paso de conguración lógica de apertura derecha/izquierda no invertir la conexión original del conector JP10.

- Bij de overgang van de conguratielogica rechts/links openen, de oorspronkelijke aansluiting van de connector JP10 niet omdraaien.

Inversione direzione di aperura: 0
Open in other direction: 0
Inversion direction de l’ouverture: 0
Richtungsumkehrung Önung: 0
Inversión dirección de apertura: 0
Openingsrichting omdraaien: 0

verso di apertura: sinistra
opening direction: left
sens de l’ouverture : gauche
Önungsrichtung: links
sentido de apertura: izquierda
openingsrichting: links

12 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

S

1
2

1
2
3

4

5

51

TX1 RX1

Bar 1

1

2

3

4

5

6

1
2

1
2
3

4

5

52
50

TX1 RX1

1
2

1
2
3
4
5

TX1 RX1

1
2

1
2
3
4
5

TX2 RX2

Bar 1

1

2

3

4

5

Bar 2

1

2

3

4

5

Bar 1

1

2

3

4

5

6

6

6

1
2

1
2
3

4

5

TX1 RX1

Bar 1

1

2

3

4

5

6

1
2

1
2
3

4

5

TX1 RX1

1
2

1
2
3
4
5

TX1 RX1

1
2

1
2
3
4
5

TX2 RX2

Bar 1

1

2

3

4

5

Bar 2

1

2

3

4

5

Bar 1

1

2

3

4

5

6

6

6

SAFE1 = 0,2,4

SAFE1 = 8,11,14

1 PHOT / 1 PHOT OP / 1 PHOT CL

1 PHOT / 1 PHOT OP / 1 PHOT CL

2 PHOT / 2 PHOT OP / 2 PHOT CL

BAR 8K2 / BAR 8K2 OP / BAR 8K2 CL

1 BAR / 1 BAR OP / 1 BAR CL

1 BAR / 1 BAR OP / 1 BAR CL

2 BAR / 2 BAR OP / 2 BAR CL

50

52
50

52
50

51
50

51

50

51
50

51

50

70

72

70

72

73

70

70

72

73

51

51

50

51

50

51

50

52

52

52

72

70

72

70

73

72
70

51

50

70
73

70
72

8,2Kohm 5%

SAFETY EDGE

SAFETY EDGE

70
74

8,2Kohm 5%

SAFETY EDGE SAFETY EDGE

1
2

1
2
3

4

5

51

TX1 RX1

Bar 1

1

2

3

4

5

6

1
2

1
2
3

4

5

52
50

TX1 RX1

1
2

1
2
3
4
5

TX1 RX1

1
2

1
2
3
4
5

TX2 RX2

Bar 1

1

2

3

4

5

Bar 2

1

2

3

4

5

Bar 1

1

2

3

4

5

6

6

6

1
2

1
2
3

4

5

TX1 RX1

Bar 1

1

2

3

4

5

6

1
2

1
2
3

4

5

TX1 RX1

1
2

1
2
3
4
5

TX1 RX1

1
2

1
2
3
4
5

TX2 RX2

Bar 1

1

2

3

4

5

Bar 2

1

2

3

4

5

Bar 1

1

2

3

4

5

6

6

6

SAFE2 = 0,2,4

SAFE2 = 6,9,12

SAFE1 = 1,3,5

SAFE2 = 1,3,5

SAFE2 = 7,10,13

1 PHOT / 1 PHOT OP / 1 PHOT CL

1 PHOT / 1 PHOT OP / 1 PHOT CL

2 PHOT / 2 PHOT OP / 2 PHOT CL

1 BAR / 1 BAR OP / 1 BAR CL

1 BAR / 1 BAR OP / 1 BAR CL

2 BAR / 2 BAR OP / 2 BAR CL

50

52
50

52
50

51

50

51
50

51
50

51
50

70

74

70

74

75

70

70

74

75

51

51

50

51

50

51

50

52

52

52

74

70

74

70

75

74
70

51

50

70
75

72

50

70

71

73

74 75

24V -

24V +

24 VSafe+

COM

SAFE 1

SAFE 2

STOP

FAULT 1

FAULT 2

NC

NC

NC

70

71

73

74 75

24V -

24V +

24 VSafe+

COM

SAFE 1

SAFE 2

STOP

FAULT 1

FAULT 2

NC

NC

NC

51

52

SAFE2

1

2

5

1

3

2

4

5

TEST OFFTEST ON

TEST OFFTEST ON

SAFE 1

SAFE 2

SAFE1 = 6,9,12

SAFE1 = 7,10,13

3

4

SAFE1 = 8,11,14

BAR 8K2 / BAR 8K2 OP / BAR 8K2 CL

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500 - 13

D812201 00100_03

ENGLISH

ACCESS MENUS Fig. 2

Exit Menù

Conrm/Switch on display

Scroll up

Scroll down

autoset

See PARAMETERS MENU

See LOGIC MENU

See RADIO MENU

add. start

hidden butt

hidden butt

release

release

desired button

desired button

Add. 2ch

erase 64

language

stat

­+

­+

OK

vers

bft . . .

+-

OK

0000

+-

+-

n. cycles

OK

OK

password

0---

10--

150- 1520 prg

00

-

+

err

+-

n. remotes

List of last 30 errors

Control unit
software version

No total
manoeuvres(in hundreds)

No radio control
devices memorised

ALT follow the user guide

x2

0---

10--

150- 1520 ok

01.33

02.01

........

30.15

***

*** Password entry.

Request with Protection Level logic set to 1, 2, 3, 4

Diagnostics

code

DESCRIPTION NOTES

STRE

START E external start input activated 

STRI

START I internal start input activated 

OPEN

OPEN input activated 

CLS

CLOSE input activated 

PED

PED pedestrian input activated 

TIME

TIMER input activated 

STOP

STOP input activated 

PHOT

PHOT photocell input activated 

PHOP

PHOT OP opening photocell input activated 

PHCL

PHOT CL closing photocell input activated 

BAR

BAR safety edge input activated 

BAR 2

BAR safety edge input activated on slave motor
(opposite leaves connection)

baro

Activation of BAR safety edge input with ACTIVE reversal
ONLY WHILE OPENING, or, if congured as veried safety
edge active only while opening, Activation of the asso­ciated FAULT input

barc

Activation of BAR safety edge input with AC TIVE rever­sal ONLY WHILE CLOSING, or, if congured as veried
safety edge active only while closing, Activation of the
associated FAULT input

SWC

SWC motor closing limit switch input activated



SWO

SWO motor opening limit switch input activated



SET

The board is standing by to per form a complete opening­closing cycle uninterrupted by intermediate stops in
order to acquire the torque required for movement.
WARNING! Obstacle detection not active



ER01

Photocell test failed

Check photocell connection and/or logic settings

ER02

Safety edge test failed

Check safety edge connection and/or logic settings

ER03

Opening photocell test failed Check photocell connection and/or parameter/logic setting

ER04

Closing photocell test failed Check photocell connection and/or parameter/logic setting

ER05

Safety edge test on slave motor failed (opposite leaves
connection)

Check safety edge connection and/or parameter/logic settings

er06

8k2 safety edge test failed Check safety edge connection and/or parameter/logic settings

ER07

Opening safety edge test failed Check safety edge connection and/or parameter/logic settings

ER08

Closing safety edge test failed Check safety edge connection and/or parameter/logic settings

ER1x*

Board hardware test error

- Check connections to motor

- Hardware problems with board (contact technical assistance)

ER3x*

Reverse due to obstacle - Amperostop Check for obstacles in path

ER4x*

Thermal cutout Allow automated device to cool

ER5x*

Communication error with remote devices

Check connection with serial-connected accessory devices
and/or expansion boards

ER7x*

Internal system supervision control error.

Try switching the board o and back on again. If the problem
persists, contact the technical assistance department.

ERf0

Limit switch error

check limit switch connections

erf1

Limit switch error always active after operation start

Check limit switch and motor connections

ERf3

Error in setting the SAFE inputs Check the setting of the SAFE inputs is correct

* X = 0,1,…,9,A,B,C,D,E,F

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500 - 23

D812201 00100_03

INSTALLER WARNINGS

Anything that is not explicitly provided for in the installation ma­nual is not allowed. The operator’s proper operation can only be
guaranteed if the information given is complied with. The Firm shall
not be answerable for damage caused by failure to comply with the
instructions featured herein.
While we will not alter the product’s essential features, the Firm reserves
the right, at any time, to make those changes deemed opportune to
improve the product from a technical, design or commercial point of
view, and will not be required to update this publication accordingly.

WARNING! Important safety instructions. Carefully read and comply with
all the warnings and instructions that come with the product as incorrect
installation can cause injury to people and animals and damage to property.
The warnings and instructions give important information regarding safety,
installation, use and maintenance. Keep hold of instructions so that you can
attach them to the technical le and keep them handy for future reference.

GENERAL SAFETY

This product has been designed and built solely for the purpose indicated herein.
Uses other than those indicated herein might cause damage to the product and
create a hazard.

- The units making up the machine and its installation must meet the requirements
of the following European Directives, where applicable: 2004/108/EC, 2006/95/
EC, 2006/42/EC, 89/106/EC, 99/05/EC and later amendments. For all countries
outside the EEC, it is advisable to comply with the standards mentioned, in ad­dition to any national standards in force, to achieve a good level of safety.

- The Manufacturer of this product (hereinafter referred to as the “Firm”) disclaims
all responsibility resulting from improper use or any use other than that for
which the product has been designed, as indicated herein, as well as for failure
to apply Good Practice in the construction of entry systems (doors, gates, etc.)
and for deformation that could occur during use.

- Installation must be carried out by qualied personnel (professional installer,
according to EN 12635), in compliance with Good Practice and current code.

- Before installing the product, make all structural changes required to produce
safety gaps and to provide protection from or isolate all crushing, shearing and
dragging hazard areas and danger zones in general in accordance with the
provisions of standards EN 12604 and 12453 or any local installation standards.
Check that the existing structure meets the necessary strength and stability
requirements.

- Before commencing installation, check the product for damage.

- The Firm is not responsible for failure to apply Good Practice in the construction
and maintenance of the doors, gates, etc. to be motorized, or for deformation
that might occur during use.

- Make sure the stated temperature range is compatible with the site in which the
automated system is due to be installed.

- Do not install this product in an explosive atmosphere: the presence of ammable
fumes or gas constitutes a serious safety hazard.

- Disconnect the electricity supply before performing any work on the system.
Also disconnect buer batteries, if any are connected.

- Before connecting the power supply, make sure the product’s ratings match the
mains ratings and that a suitable residual current circuit breaker and overcurrent
protection device have been installed upline from the electrical system. Have
the automated system’s mains power supply tted with a switch or omnipolar
thermal-magnetic circuit breaker with a contact separation that provide full
disconnection under overvoltage category III conditions.

- Make sure that upline from the mains power supply there is a residual current
circuit breaker that trips at no more than 0.03A as well as any other equipment
required by code.

- Make sure the earth system has been installed correctly: earth all the metal parts
belonging to the entry system (doors, gates, etc.) and all parts of the system
featuring an earth terminal.

- Installation must be carried out using safety devices and controls that meet
standards EN 12978 and EN 12453.

- Impact forces can be reduced by using deformable edges.

- In the event impact forces exceed the values laid down by the relevant standards,
apply electro-sensitive or pressure-sensitive devices.

- Apply all safety devices (photocells, safety edges, etc.) required to keep the
area free of impact, crushing, dragging and shearing hazards. Bear in mind the
standards and directives in force, Good Practice criteria, intended use, the instal­lation environment, the operating logic of the system and forces generated by
the automated system.

- Apply all signs required by current code to identify hazardous areas (residual
risks). All installations must be visibly identied in compliance with the provisions
of standard EN 13241-1.

- Once installation is complete, apply a nameplate featuring the door/gate’s data.

- This product cannot be installed on leaves incorporating doors (unless the motor
can be activated only when the door is closed).

- If the automated system is installed at a height of less than 2.5 m or is accessible,
the electrical and mechanical parts must be suitably protected.

- For roller shutter automation only

1) The motor’s moving parts must be installed at a height greater than 2.5 m
above the oor or other surface from which they may be reached.

2) The gearmotor must be installed in a segregated and suitably protected space
so that it cannot be reached without the aid of tools.

- Install any xed controls in a position where they will not cause a hazard, away
from moving parts. More specically, hold-to-run controls must be positioned
within direct sight of the part being controlled and, unless they are key operated,
must be installed at a height of at least 1.5 m and in a place where they cannot
be reached by the public.

- Apply at least one warning light (ashing light) in a visible position, and also
attach a Warning sign to the structure.

- Attach a label near the operating device, in a permanent fashion, with informa­tion on how to operate the automated system’s manual release.

- Make sure that, during operation, mechanical risks are avoided or relevant
protective measures taken and, more specically, that nothing can be banged,
crushed, caught or cut between the part being operated and surrounding parts.

- Once installation is complete, make sure the motor automation settings are
correct and that the safety and release systems are working properly.

- Only use original spare parts for any maintenance or repair work. The Firm dis­claims all responsibility for the correct operation and safety of the automated
system if parts from other manufacturers are used.

- Do not make any modications to the automated system’s components unless
explicitly authorized by the Firm.

- Instruct the system’s user on what residual risks may be encountered, on the
control systems that have been applied and on how to open the system manu­ally in an emergency. give the user guide to the end user.

- Dispose of packaging materials (plastic, cardboard, polystyrene, etc.) in accord­ance with the provisions of the laws in force. Keep nylon bags and polystyrene
out of reach of children.

WIRING
WARNING! For connection to the mains power supply, use: a multicore cable with

a cross-sectional area of at least 5x1.5mm

2

or 4x1.5mm2 when dealing with three­phase power supplies or 3x1.5mm2 for single-phase supplies (by way of example,
type H05 VV-F cable can be used with a cross-sectional area of 4x1.5mm2). To con­nect auxiliary equipment, use wires with a cross-sectional area of at least 0.5 mm2.

- Only use pushbuttons with a capacity of 10A-250V or more.

- Wires must be secured with additional fastening near the terminals (for example,

using cable clamps) in order to keep live parts well separated from safety extra
low voltage parts.

- During installation, the power cable must be stripped to allow the earth wire

to be connected to the relevant terminal, while leaving the live wires as short
as possible. The earth wire must be the last to be pulled taut in the event the

cable’s fastening device comes loose.
WARNING! safety extra low voltage wires must be kept physically separate from
low voltage wires.
Only qualied personnel (professional installer) should be allowed to access
live parts.

CHECKING THE AUTOMATED SYSTEM AND MAINTENANCE

Before the automated system is nally put into operation, and during maintenance
work, perform the following checks meticulously:

- Make sure all components are fastened securely.

- Check starting and stopping operations in the case of manual control.

- Check the logic for normal or personalized operation.

- For sliding gates only: check that the rack and pinion mesh correctly with 2 mm

of play along the full length of the rack; keep the track the gate slides on clean
and free of debris at all times.

- For sliding gates and doors only: make sure the gate’s running track is straight

and horizontal and that the wheels are strong enough to take the weight of the
gate.

- For cantilever sliding gates only: make sure there is no dipping or swinging

during operation.

- For swing gates only: make sure the leaves’ axis of rotation is perfectly vertical.

-For barriers only: before opening the door, the spring must be decompressed

(vertical boom).

- Check that all safety devices (photocells, safety edges, etc.) are working properly

and that the anti-crush safety device is set correctly, making sure that the force
of impact measured at the points provided for by standard EN 12445 is lower
than the value laid down by standard EN 12453.

- Impact forces can be reduced by using deformable edges.

- Make sure that the emergency operation works, where this feature is provided.

- Check opening and closing operations with the control devices applied.

- Check that electrical connections and cabling are intact, making extra sure that

insulating sheaths and cable glands are undamaged.

- While performing maintenance, clean the photocells’ optics.

- When the automated system is out of service for any length of time, activate the

emergency release (see “EMERGENCY OPERATION” section) so that the operated
part is made idle, thus allowing the gate to be opened and closed manually.

-

If the power cord is damaged, it must be replaced by the manufacturer or their
technical assistance department or other such qualied person to avoid any risk .

- If “D” type devices are installed (as dened by EN12453), connect in unveried

mode, foresee mandatory maintenance at least every six months

- The maintenance described above must be repeated at least once yearly or at

shorter intervals where site or installation conditions make this necessary.

WARNING!

Remember that the drive is designed to make the gate/door easier to use and
will not solve problems as a result of defective or poorly performed installation
or lack of maintenance

SCRAPPING

Materials must be disposed of in accordance with the regulations in

force. Do not throw away your discarded equipment or used batteries
with household waste. You are responsible for taking all your waste
electrical and electronic equipment to a suitable recycling centre.

DISMANTLING

If the automated system is being dismantled in order to be reassembled at another
site, you are required to:

- Cut o the power and disconnect the whole electrical system.

- Remove the actuator from the base it is mounted on.

- Remove all the installation’s components.

- See to the replacement of any components that cannot be removed or happen

to be damaged.

DECLARATIONS OF CONFORMITY CAN BE FOUND AT http://www.bft-

automation.com/CE

INSTRUCTIONS FOR USE AND ASSEMBLY CAN BE FOUND IN THE DOWN­LOAD SECTION.

D811766_14

24 -

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

ENGLISH

INSTALLATION MANUAL

1) GENERAL INFORMATION

The ARES ULTRA BT A actuator is highly versatile in terms of installation op-
tions due to the extremely low position of the pinion, the actuator’s compact
nature and the height and depth adjustment features it oers. The adjustable
electronic torque limiter provides anti-crush safety. Manual emergency operation
is extremely easy to perform using just a release lever.
Stopping is controlled by polarized magnetic limit switches.
The MERAK control panel comes with standard factory settings. Any change
must be made using the programmer with built-in display or universal handheld
programmer.
Fully supports EELINK and U-LINK protocols.
Its main features are:

- Control of 1 low-voltage motor

- Obstacle detection

- Separate inputs for safety devices

- Congurable command inputs

- Built-in radio receiver rolling code with transmitter cloning.
The board has a terminal strip of the removable kind to make maintenance
or replacement easier. It comes with a series of prewired jumpers to make the
installer’s job on site easier. The jumpers concern terminals: 70-71, 70-72, 70-74.
If the above-mentioned terminals are being used, remove the relevant jumpers.

TESTING

The MERAK panel controls (checks) the start relays and safety devices (photocells)
before performing each opening and closing cycle.
If there is a malfunction, make sure that the connected devices are working
properly and check the wiring.

2) TECHNICAL SPECIFICATIONS
MOTOR

1000 1500

Power supply

110-120V 50/60Hz

220-230V 50/60 Hz(*)
Power input 240 W 400 W

Pinion module

ARES

4mm (18 teeth) 4mm (18 teeth)

Pinion module

ARES V

4mm (25 teeth) 4mm (25 teeth)

Leaf speed

ARES

9 m/min 9 m/min

Leaf speed

ARES V

12 m/min 12 m/min

Max. leaf weight

ARES

1000 Kg 1500 Kg

Max. leaf weight

ARES V

500 Kg 750 Kg

Max. torque 30 Nm 35 Nm

Impact reaction Electronic torque limiter

Lubrication Lifetime greased

Manual operation Lever-operated mechanical release

Type of use intensive

Buf fer batteri es (optional
extras)

Two 12V 1.2Ah batteries

Environmental conditions -20 / +55°C

Protection rating IP44

Noise level <70dBA

Operator weight 7 kg

Dimensions See Fig. H

CONTROL UNIT

Low voltage/mains insulation

> 2MOhm 500V

Operating temperature range

-20 / +55°C

Thermal overload protection Software

Dielectric rigidity mains/LV 3750V~ for 1 minute

Accessories power supply

24V ~ (demand max. 0,5A) 24V ~ safe

AUX 0

NO 24V ~ powered contact (max.1A)

AUX 3

NO contact (24V~/max.1A)

Fuses

Fig. F

Built-in Rolling-Code radio-receiver

frequency 433.92MHz

Setting of parameters and
options

Universal handheld programmer/LCD display

N° of combinations

4 billion

Max. n° of remotes that can
be memorized

63

(*) Special supply voltages to order.

Usable transmitter versions:
All ROLLING CODE transmitters compatible with

.

3) TUBE ARRANGEMENT Fig.A

Install the electrical system referring to the standards in force for electrical systems
CEI 64-8, IEC 364, harmonization document HD 384 and other national standards.

4) PREPARATION FOR MOTOR MOUNTING FIG.B

Make a hole in the ground to accommodate the concrete pad where the tie rods
will be positioned, keeping to the distances featured in (FIG.B).

5) REMOVING THE COVER FIG.C

5.1) MOUNTING THE MOTOR FIG.C1

6) MOUNTING DRIVE ACCESSORIES FIG.D-D1
Recommended rack types (FIG.J)

7) RACK CENTRING WITH RESPECT TO PINION FIG.J-K1-L
DANGER - Welding must be performed by a competent person issued

with the necessary personal protective equipment as prescribed by

the safety rules in force FIG.K.

8) FASTENING LIMIT SWITCH BRACKETS FIG.E

Fastening the limit switches:

t"UUBDIUIFMJNJUTXJUDICSBDLFUUPUIFSBDLBTJMMVTUSBUFEJO'*(D1

t'BTUFOUIFNBHOFUJDMJNJUTXJUDICPYUPUIFMJNJUTXJUDICSBDLFUXJUIUIFTDSFXT

and plate provided, as illustrated in FIG.E – Ref.1.

t'BTUFOUIFMJNJUTXJUDICSBDLFUUPUIFSBDLCZTDSFXJOHJOUIFUXPGSPOUTDSFXT

provided FIG.E ref.2

Right-hand limit switch:

t'BTUFOUIF3JHIUIBOENBHOFUJDMJNJUTXJUDIDBMMFEi3wEPOPUFYDFFEUIFTUB-

ted maximum distance between the magnetic limit switch box and the limit
switch assembly, FIG.E.

Left-hand limit switch:

t'BTUFOUIF-FGUIBOENBHOFUJDMJNJUTXJUDIDBMMFEi-wEPOPUFYDFFEUIFTUBUFE

maximum distance between the magnetic limit switch box and the limit
switch assembly, FIG.E.

Warning. Do not swap over the limit switch brackets once you have changed the

opening direction via the relevant logic

9) STOPS FIG.M
DANGER - The gate must be tted with mechanical stops to halt its

travel both when opening and closing, thus preventing the gate from

coming o the top guide. Said stops must be fastened rmly to the ground,
a few centimetres beyond the electric stop point.

10) MANUAL RELEASE (See USER GUIDE -FIG.3-).

Warning Do not JERK the gate open and closed, instead push it GENTLY to
the end of its travel.

11) TERMINAL BOARD WIRING Fig. F-N

Once suitable electric cables have been run through the raceways and the auto­mated device’s various components have been fastened at the predetermined
points, the next step is to connect them as directed and illustrated in the diagrams
contained in the relevant instruction manuals. Connect the live, neutral and earth
wire (compulsory). The mains cable must be clamped in the relevant cable gland
(FIG.N-ref.N1), while the earth wire with the yellow/green-coloured sheath must
be connected in the relevant terminal (FIG.N-ref.N2).

WARNINGS - When performing wiring and installation, refer to the standards
in force and, whatever the case, apply good practice principles. Wires carrying
dierent voltages must be kept physically separate from each other, or they must
be suitably insulated with at least 1mm of additional insulation.
Wires must be secured with additional fastening near the terminals, using devi­ces such as cable clamps. All connecting cables must be kept far enough away
from dissipaters.

11.1) LOCAL COMMANDS Fig.F

While the display is o, pressing the + key commands the gate to Open and
pressing the - key commands it to Close. Pressing either key again while the
automated device is moving commands the gate to STOP.

12) SAFETY DEVICES

Note: only use receiving safety devices with free changeover contact.

12.1) TESTED DEVICES Fig.S

12

.2 CONNECTION OF 1 PAIR OF NONTESTED PHOTOCELLS FIG. G

13 ACCESS TO THE SIMPLIFIED MENU: FIG.1

13.1) CALLING UP MENUS: FIG. 2

13.2) PARAMETERS MENU PARA

 PARAMETERS TABLE “A”

13.3) LOGIC MENU LOGIC LOGIC TABLE “B”

13.4) RADIO MENU radio RADIO TABLE “C”

- IMPORTANT NOTE: THE FIRST TRANSMITTER MEMORIZED MUST BE

IDENTIFIED BY ATTACHING THE KEY LABEL (MASTER).

In the event of manual programming, the rst transmitter assigns the RECEIVER’S
KEY CODE: this code is required to subsequently clone the radio transmitters.
The Clonix built-in on-board receiver also has a number of important advanced features:

t$MPOJOHPGNBTUFSUSBOTNJUUFSSPMMJOHDPEFPSöYFEDPEF

t$MPOJOHUPSFQMBDFUSBOTNJUUFSTBMSFBEZFOUFSFEJOSFDFJWFS

t5SBOTNJUUFSEBUBCBTFNBOBHFNFOU

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500 - 25

D812201 00100_03

INSTALLATION MANUAL

Terminal Denition Description

Power supply

L LINE

Single-phase power supply

N NEUTRAL

JP31

TRANSF PRIM Transformer primary winding connection

JP32

JP13 TRANSF SEC

Board power supply:
24V~ Transformer secondar y winding

Motor

10 MOT +

Connection motor 1

11 MOT -

Aux

20

AUX 0 - 24V POWERED CONTACT

(N.O.) (MAX. 1A)

AUX 0 congurable output - Default setting FLASHING LIGHT.
2ND RADIO CHANNEL/ SCA GATE OPEN LIGHT/ COURTESY LIGHT command/ ZONE LIGHT command/ STAIR LIGHT/
GATE OPEN ALARM/ FLASHING LIGHT/ SOLENOID LATCH/ MAGNETIC LOCK/ MAINTENANCE/ FLASHING LIGHT AND
MAINTENANCE. Refer to “AUX output conguration” table.

21

26

AUX 3 - FREE CONTACT (N.O.)

(Max. 24V 1A)

AUX 3 congurable output - Default setting 2ND RADIO CHANNEL Output.
2ND RADIO CHANNEL/ SCA GATE OPEN LIGHT/ COURTESY LIGHT command/ ZONE LIGHT command/ STAIR LIGHT/
GATE OPEN ALARM/ FLASHING LIGHT/ SOLENOID LATCH/ MAGNETIC LOCK/ MAINTENANCE/ FLASHING LIGHT AND
MAINTENANCE. Refer to “AUX output conguration” table.

27

Limit

switches

JP10 Limit switches Limit switch assembly connection

Accessories

power

supply

50 24V~ (-)

Accessories power supply output.

51 24V ~ (+)

52 24 Vsafe

Tested safety device power supply output (photocell transmitter and safety edge transmitter).
Output active only during operating cycle.

Commands

60 Common IC 1 and IC 2 inputs common

61 IC 1

Congurable command input 1 (N.O.) - Default START E.
START E / START I / OPEN / CLOSE / PED / TIMER / TIMER PED
Refer to the “Command input conguration” table.

62 IC 2

Congurable command input 2 (N.O.) - Default PED.
START E / START I / OPEN / CLOSE / PED / TIMER / TIMER PED
Refer to the “Command input conguration” table.

Safety devices

70 Common STOP, SAFE 1 and SAFE 2 inputs common

71 STOP

The command stops movement. (N.C.)
If not used, leave jumper inserted.

72 SAFE 1

Congurable safety input 1 (N.C.) - Default PHOT.
PHOT / PHOT TEST / PHOT OP / PHOT OP TEST / PHOT CL / PHOT CL TEST / BAR / BAR TEST / BAR 8K2 /

BAR OP / BAR OP
TEST / BAR 8K2 OP/ BAR CL / BAR CL TEST / BAR 8K2 CL
Refer to the “Safety input conguration” table.

73 FAULT 1 Test input for safety devices connected to SAFE 1.

74 SAFE 2

Congurable safety input 2 (N.C.) - Default BAR.
PHOT / PHOT TEST / PHOT OP / PHOT OP TEST / PHOT CL / PHOT CL TEST / BAR / BAR TEST / BAR 8K2 /

BAR OP / BAR OP
TEST / BAR 8K2 OP/ BAR CL / BAR CL TEST / BAR 8K2 CL
Refer to the “Safety input conguration” table.

75 FAULT 2 Test input for safety devices connected to SAFE 2.

Anten-

na

Y ANTENNA

Antenna input.
Use an antenna tuned to 433MHz. Use RG58 coax cable to connect the Antenna and Receiver. Metal bodies close to the an­tenna can interfere with radio reception. If the transmitter’s range is limited, move the antenna to a more suitable position.

# SHIELD

AUX output conguration

Aux logic= 0 - 2ND RADIO CHANNEL output.
Contact stays closed for 1s when 2nd radio channel is activated.

Aux logic= 1 - SCA GATE OPEN LIGHToutput.
Contact stays closed during opening and with leaf open, intermittent during closing, open with leaf closed.

Aux logic= 2 - COURTESY LIGHT command output.
Contact stays on for 90 seconds after the last operation.

Aux logic= 3 - ZONE LIGHT command output.
Contact stays closed for the full duration of operation.

Aux logic= 4 - STAIR LIGHT output.
Contact stays closed for 1 second at start of operation.

Aux logic= 5 - GATE OPEN ALARM output.
Contact stays closed if the leaf stays open for double the set TCA time.

Aux logic= 6 - FLASHING LIGHT output.
Contact stays closed while leaves are operating.

Aux logic= 7 - SOLENOID LATCH output.
Contact stays closed for 2 seconds each time gate is opened.

Aux logic= 8 - MAGNETIC LOCK output.
Contact stays closed while gate is closed.

Aux logic= 9 - MAINTENANCE output.
Contact stays closed once the value set for the Maintenance parameter is reached, to report that maintenance is required.

Aux logic= 10 - FLASHING LIGHT AND MAINTENANCE output.
Contact stays closed while leaves are operating. If the value set for the Maintenance parameter is reached, once the gate has nished moving and the leaf is closed, the contact closes
for 10 sec. and opens for 5 sec. 4 times to report that maintenance is required.

Note : If no output is congured as 2nd Radio Channel Output, the 2nd radio channel controls the pedestrian opening.

Command input conguration

IC logic= 0 - Input congured as Start E. Operation according to STEP-BY-STEP MOV. logic. External start for trac light control.

IC logic= 1 - Input congured as Start I. Operation according to STEP-BY-STEP MOV. logic. Internal start for trac light control.
IC logic= 2 - Input congured as Open.
The command causes the leaves to open. If the input stays closed, the leaves stay open until the contact is opened. When the contact is open, the automated device closes following
the TCA time, where activated.
IC logic= 3 - Input congured as Closed.
The command causes the leaves to close.

IC logic= 4 - Input congured as Ped.
The command causes the leaf to open to the pedestrian (partial) opening position. Operation according to STEP-BY-STEP. logic

IC logic= 5 - Input congured as Timer.
Operation same as open except closing is guaranteed even after a mains power outage.

IC logic= 6 - Input congured as Timer Ped.
The command causes the leaf to open to the pedestrian (partial) opening position. If the input stays closed, the leaf stays open until the contact is opened. If the input stays closed and a Start E,
Start I or Open command is activated, a complete opening-closing cycle is performed before returning to the pedestrian opening position. Closing is guaranteed even after a mains power outage.

26 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

ENGLISH

INSTALLATION MANUAL

Safety input conguration

SAFE logic= 0 - Input congured as Phot (photocell) non tested (*). (g.S, ref.1).
Enables connection of devices not equipped with supplementary test contacts. When beam is broken, photocells are active during both opening and closing. When beam is broken
during closing, movement is reversed only once the photocell is cleared. If not used, leave jumper inser ted.

SAFE logic= 1 - Input congured as Phot test (tested photocell). (g.S, ref.2).
Switches photocell testing on at start of operation. When beam is broken, photocells are active during both opening and closing. When beam is broken during closing, movement is
reversed only once the photocell is cleared.

SAFE logic= 2 - Input congured as Phot op (photocell active during opening only) non tested (*). (g.S, ref.1).
Enables connection of devices not equipped with supplementary test contacts. In the event beam is broken, photocell operation is disabled during closing. During opening, stops
motion for as long as the photocell beam stays broken. If not used, leave jumper inserted.

SAFE logic= 3 - Input congured as Phot op test (tested photocell active during opening only (g.S, ref.2).
Switches photocell testing on at start of operation. In the event beam is broken, photocell operation is disabled during closing. During opening, stops motion for as long as the photocell beam stays broken.

SAFE logic= 4 - Input congured as Phot cl (photocell active during closing only) non tested (*). (g.S, ref.1).
Enables connection of devices not equipped with supplementary test contacts. In the event beam is broken, photocell operation is disabled during opening. During closing,
movement is reversed immediately. If not used, leave jumper inser ted.

SAFE logic= 5 - Input congured as Phot cl test (tested photocell active during closing only (g.S, ref.2).
Switches photocell testing on at start of operation. In the event beam is broken, photocell operation is disabled during opening. During closing, movement is reversed immediately.

SAFE logic= 6 - Input congured as Bar (safety edge) non tested (*). (g.S, ref.3).
Enables connection of devices not equipped with supplementary test contacts. The command reverses movement for 2 sec.. If not used, leave jumper inserted.

SAFE logic= 7 - Input congured as Bar (tested safety edge (g.S, ref.4).
Switches safety edge testing on at start of operation. The command reverses movement for 2 sec.

SAFE logic= 8 - Input congured as Bar 8k2 (g.S, ref.5). Input for resistive edge 8K2.
The command reverses movement for 2 sec.

SAFE logic=9 Input congured as Bar op, safety edge with active inversion only while opening, if activated while closing, the automation stops (STOP) (Fig. D, ref. 3).
Allows connecting devices not tted with supplementary test contact. The operation while opening causes the movement to be reversed for 2 seconds, the operation while closing
causes the automation to stop. If not used, leave jumper inserted.

SAFE logic=10 Input congured as Bar op test, safety edge checked with active inversion only while opening, if activated while closing, the automation stops (STOP) (Fig. D, ref. 4).
Activates testing safety edges when starting operation. The operation while opening causes the movement to be reversed for 2 seconds, the operation while closing causes the auto­mation to stop.

SAFE logic=11 Input congured as Bar 8k2 op, 8k2 safety edge with active inversion only while opening, if activated while closing, the automation stops (STOP) (Fig. D, ref. 5).
The operation while opening causes the movement to be reversed for 2 seconds, the operation while closing causes the automation to stop.

SAFE logic=12 Input congured as Bar cl, safety edge with active inversion only while closing, if activated while opening, the automation stops (STOP) (Fig. D, ref. 3).
Allows connecting devices not tted with supplementary test contact. The operation while closing causes the movement to be reversed for 2 seconds, the operation while opening
causes the automation to stop. If not used, leave jumper inserted.

SAFE logic=13 Input congured as Bar cl test, safety edge checked with active inversion only while closing, if activated while opening, the automation stops (STOP) (Fig. D, ref. 4).
Activates testing safety edges when starting operation. The operation while closing causes the movement to be reversed for 2 seconds, the operation while opening causes the auto­mation to stop.

SAFE logic=14 Input congured as Bar 8k2 cl, safety edge with active inversion only while closing, if activated while opening, the automation stops (STOP) (Fig. D, ref. 5).
The operation while closing causes the movement to be reversed for 2 seconds, the operation while opening causes the automation to stop.

(*) If “D” type devices are installed (as dened by EN12453), connect in unveried mode, foresee mandatory maintenance at least every six months.

t3FDFJWFSDPNNVOJUZNBOBHFNFOU

To use these advanced features, refer to the universal handheld programmer’s
instructions and to the general receiver programming guide.

13.5 DEFAULT MENU default

Restores the controller’s DEFAULT factory settings. Following this reset, you will
need to run the AUTOSET function again.

13.6 LANGUAGE MENU language

Used to set the programmer’s language on the display.

13.7 AUTOSET MENU AUTOset

t

For best results, it is advisable to run the autoset function with the motors idle
(i.e. not overheated by a considerable number of consecutive operations).

t

Launch an autoset operation by going to the relevant menu.

t

As soon as you press the OK button, the “.... .... ....” message is displayed and the control

unit commands the device to perform a full cycle (opening followed by closing), during

which the minimum torque value required to move the leaf is set automatically.
The number of cycles required for the autoset function can range from 1 to 3.
During this stage, it is important to avoid breaking the photocells’ beams and not

to use the START and STOP commands or the display.
Pressing the + and - keys at the same time during this stage stops the automated

device and exits the autoset operation, with the message KO appearing on the

display.

Once this operation is complete, the control unit will have automatically
set the optimum torque values. Check them and, where necessary, edit them as
described in the programming section.

WARNING!! Check that the force of impact measured at the points
provided for by standard EN 12445 is lower than the value laid down

by standard EN 12453.

Impact forces can be reduced by using deformable edges.

Warning!! While the autoset function is running, the obstacle detection
function is not active. Consequently, the installer must monitor the
automated system’s movements and keep people and property out

of range of the automated system.

INSTALLATION TEST PROCEDURE

1. Run the AUTOSET cycle (*)

2. Check the impact forces: if they fall within the limits (**) skip to point 10 of the
procedure, otherwise

3. Where necessary, adjust the speed and sensitivity (force) parameters: see
parameters table.

4. Check the impact forces again: if they fall within the limits (**) skip to point 10
of the procedure, otherwise

5. Apply a shock absorber prole

6. Check the impact forces again: if they fall within the limits (**) skip to point 10
of the procedure, otherwise

7. Apply pressure-sensitive or electro-sensitive protective devices (such as a
safety edge)

8. Check the impact forces again: if they fall within the limits (**) skip to point 10
of the procedure, otherwise

9. Allow the drive to move only in “Deadman” mode

10. Make sure all devices designed to detect obstacles within the system’s operating
range are working properly

(*) Before running the autoset function, make sure you have performed all the

assembly and make-safe operations correctly, as set out in the installation
warnings in the drive’s manual.

(**) Based on the risk analysis, you may nd it necessary to apply sensitive

protective devices anyway

13.8 STATISTICS MENU STAT

Used to view the version of the board, the total number of operations (in
hundreds), the number of transmitters memorized and the last 30 errors (the
rst 2 digits indicate the position, the last 2 give the error code). Error 01 is the
most recent.

13.9) PASSWORD MENU (PASSWORD)

Used to set a password for the board’s wireless programming via the U-link network.
With “PROTECTION LEVEL” logic set to 1,2,3,4, the password is required to access
the programming menus. After 10 consecutive failed attempts to log in, you will
need to wait 3 minutes before trying again. During this time, whenever an attempt
is made to log in, the display will read “BLOC”. The default password is 1234.

14) CONNECTION WITH EXPANSION BOARDS AND UNIVERSAL HANDHELD

PROGRAMMER VERSION> V1.40 (Fig. O) Refer to specic manual.

WARNING! Incorrect settings can result in damage to property and injury to people
and animals.

15) U-LINK OPTIONAL MODULES

Refer to the U-link instructions for the modules.

15.1) REFER TO THE ULINK MODULE’S INSTRUCTIONS FIG. P.

Refer to the U-link instructions for the modules.
NOTE: On the board set as the Slave, the Safety Edge input (Safety Edge/ Test
Safety Edge/ 8k2 Safety Edge) should only be set to SAFE2.

16) REVERSING THE OPENING DIRECTION (Fig.Q)

17) RESTORING FACTORY SETTINGS (Fig.R)

WARNING: this operation will restore the control unit’s factory settings and all

transmitters stored in its memory will be deleted.
WARNING! Incorrect settings can result in damage to property and injury to
people and animals.

- Cut o power to the board (Fig.R ref.1)

- Open the Stop input and press the - and OK keys together (Fig.R ref.2)

- Switch on the board’s power (Fig.R ref.3)

- The display will read RST; conrm within 3 sec. by pressing the OK key (Fig.R ref.4)

- Wait for the procedure to nish (Fig.R ref.5)

- Procedure nished (Fig.R ref.6)

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

-

27

D812201 00100_03

INSTALLATION MANUAL

TABLE “A”  PARAMETERS MENU - PARA 

Parameter min. max. Default

Personal

Denition Description

TCA

0 120 10

Automatic clos-

ing time [s]

Waiting time before automatic closing.

TRF.LGHT.

CLR.T

1 180 40

Time-to-clear

trac light zone

[s]

Time-to-clear for the zone run through by trac controlled by the trac light.

OP.DIST.

SLOUD

5 50 10

Slow-down

distance during

opening [%]

Slow-down distance for motor(s) during opening, given as a percentage of total
travel. WARNING: Once the parameter has been edited, a complete uninterrupted

opening-closing cycle is required.
WARNING: when the display reads “SET”, obstacle detection is not active.

CL.DIST.

SLOUD

5 50 10

Slow-down

distance during

closing [%]

Slow-down distance for motor(s) during closing, given as a percentage of total travel.

WARNING: Once the parameter has been edited, a complete uninterrupted
opening-closing cycle is required.
WARNING: when the display reads “SET”, obstacle detection is not active.

DIST.DECEL

0 50 15

Deceleration
distance [%]

Deceleration distance (switch from running speed to slow-down speed) for motor(s) both
during opening and during closing, given as a percentage of total travel. WARNING: Once the

parameter has been edited, a complete uninterrupted opening-closing cycle is required.
WARNING: when the display reads “SET”, obstacle detection is not active.

PARTIAL

OPENING

10 99 20

Partial opening

[%]

Partial opening distance as a percentage of total opening following activation of PED pedestrian
command.

OP.FORCE

1 99 50

Leaf force

during opening

[%]

Force exerted by leaf/leaves during opening. This is the percentage of force delivered,
beyond the force stored during the autoset cycle (and subsequently updated), before
an obstacle alarm is generated.
The parameter is set automatically by the autoset function.

WARNING: It aects impact force directly: make sure that current safety
requirements are met with the set value (*). Install anti-crush safety

devices where necessary (**).

CLS.FORCE

1 99 50

Leaf force

during closing

[%]

Force exerted by leaf/leaves during closing. This is the percentage of force delivered,
beyond the force stored during the autoset cycle (and subsequently updated), before
an obstacle alarm is generated.
The parameter is set automatically by the autoset function.

WARNING: It aects impact force directly: make sure that current safety
requirements are met with the set value (*). Install anti-crush safety

devices where necessary (**).

OP.SLWD.FORCE

1 99 50

Leaf/leaves

force during

opening during

slow-down

“Force exerted by leaf/leaves during opening at slow-down speed.”
This is the percentage of force delivered, beyond the force stored during the autoset cycle (and
subsequently updated), before an obstacle alarm is generated.

The parameter is set automatically by the autoset function.

WARNING: It aects impact force directly: make sure that current safety
requirements are met with the set value (*). Install anti-crush safety

devices where necessary (**).

CLS.SLWD.

FORCE

1 99 50

Leaf/leaves force

during closing

during slow-down

[%]

“Force exerted by leaf/leaves during closing at slow-down speed. “
This is the percentage of force delivered, beyond the force stored during the autoset cycle (and
subsequently updated), before an obstacle alarm is generated.

The parameter is set automatically by the autoset function.

WARNING: It aects impact force directly: make sure that current safety
requirements are met with the set value (*). Install anti-crush safety

devices where necessary (**).

OP SPEED

15 99 99

Opening speed

[%}

Percentage of maximum speed that can be reached by motor(s) during opening.

WARNING: Once the parameter has been edited, a complete uninterrupted
opening-closing cycle is required. WARNING: when the display reads "SET",
obstacle detection is not active.

CL SPEED

15 99 99

Closing speed

[%]

Percentage of maximum speed that can be reached by motor(s) during closing.

WARNING: Once the parameter has been edited, a complete uninterrupted
opening-closing cycle is required. WARNING: when the display reads "SET",
obstacle detection is not active.

SLOW SPEED

15 30 25

Slow-down

speed [%]

Opening and closing speed of motor(s) during slow-down stage, given as a percentage of
maximum running speed. WARNING: Once the parameter has been edited, a complete

uninterrupted opening-closing cycle is required. WARNING: When the display reads
“”SET””, obstacle detection is not active.

Maintenance

0 250 0

Programming num-

ber of operations

for maintenance

threshold

[in hundreds]

Allows you to set a number of operations after which the need for maintenance will be repor­ted on the AUX output congured as Maintenance or Flashing Light and Maintenance .

(*) In the European Union, apply standard EN 12453 for force limitations, and standard EN 12445 for measuring method.
(**) Impact forces can be reduced by using deformable edges.

28 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

ENGLISH

INSTALLATION MANUAL

TABLE “B”  LOGIC MENU - logic

Logic Denition

De-

fault

Cross out

setting

used

Optional extras

TCA

Automatic Clo-

sing Time

0

0 Logic not enabled

1 Switches automatic closing on

FAST CLS.

Fast closing 0

0 Logic not enabled

1 Closes 3 seconds after the photocells are cleared before waiting for the set TCA to elapse.

STEP-BY-STEP

MOVEMNT

Step-by-step

movement

0

0

Inputs congured as Start E, Start I, Ped
operate with 4-step logic.

step-by-step mov.

2 STEP 3 STEP 4 STEP

CLOSED

OPENS OPENS

OPENS

DURING

CLOSING

STOPS

OPEN

CLOSES

CLOSES CLOSES

DURING

OPENING

STOP + TCA

STOP + TCA

AFTER STOP

OPENS OPENS OPENS

1

Inputs congured as Start E, Start I, Ped op­erate with 3-step logic. Pulse during closing
reverses movement.

2

Inputs congured as Start E, Start I, Ped op­erate with 2-step logic. Movement reverses
with each pulse.

PRE-ALARM

Pre-alarm 0

0 The ashing light comes on at the same time as the motor(s) start.

1 The ashing light comes on approx. 3 seconds before the motor(s) start.

HOLD-TO-RUN

Deadman 0

0 Pulse operation.

1

Deadman mode.
Input 61 is congured as OPEN UP.
Input 62 is congured as CLOSE UP.
Operation continues as long as the OPEN UP or CLOSE UP keys are held down.

WARNING: safety devices are not enabled.

2

Emergency Deadman mode. Us

ually pulse operation.
If the board fails the safety device tests (photocell or safety edge, Er0x) 3 times in a row, Deadman mode is
enabled which will stay active for 1 minute after the OPEN UP - CLOSE UP keys are released.
Input 61 is congured as OPEN UP.
Input 62 is congured as CLOSE UP.

WARNING: with the device set to Emergency Deadman mode, safety devices are not enabled.

IBL OPEN

Block pulses

during opening

0

0 Pulse from inputs congured as Start E, Start I, Ped has eect during opening.

1 Pulse from inputs congured as Start E, Start I, Ped has no eect during opening.

IBL TCA

Block pulses

during TCA

0

0 Pulse from inputs congured as Start E, Start I, Ped has eect during TCA pause.

1 Pulse from inputs congured as Start E, Start I, Ped has no eect during TCA pause.

IBL CLOSE

Block pulses

during closing

0

0 Pulse from inputs congured as Start E, Start I, Ped has eect during closing.

1 Pulse from inputs congured as Start E, Start I, Ped has no eect during closing.

ICE

Ice feature 0

0 The Amperostop safety trip threshold stays at the same set value.

1

The controller automatically adjusts the obstacle alarm trip threshold at each start up.
Check that the force of impact measured at the points provided for by standard EN 12445 is lower than the
value laid down by standard EN 12453. If in doubt, use auxiliary safety devices.
This feature is useful when dealing with installations running at low temperatures.
WARNING: once this feature has been activated, you will need to perform an autoset opening and closing cycle.

OPEN IN

OTHER DIRECT.

Open in other

direction

0

0

Standard operating mode (See Fig.Q Ref. 1).

1 Opens in other direction to standard operating mode (See Fig. Q Ref.2)

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

- 29

D812201 00100_03

INSTALLATION MANUAL

Logic Denition

De-

fault

Cross out

setting

used

Optional extras

SAFE 1

Conguration

of safety input

SAFE 1.

72

0

0 Input congured as Phot (photocell).

1 Input congured as Phot test (tested photocell).

2 Input congured as Phot op (photocell active during opening only).

3 Input congured as Phot op test (tested photocell active during opening only).

SAFE 2

Conguration

of safety input

SAFE 2.

74

6

4 Input congured as Phot cl (photocell active during closing only).

5 Input congured as Phot cl test (tested photocell active during closing only).

6 Input congured as Bar, safety edge.

7 Input congured as Bar, tested safety edge.

8 Input congured as Bar 8k2.

9

*

Input congured as Bar OP, safety edge with inversion active only while opening. If while closing, the mo­vement stops.

10

*

Input congured as Bar OP TEST, safety edge tested with inversion active only while opening. If while closing,
the movement stops.

11

*

Input congured as Bar OP 8k2, safety edge with inversion active only while opening. If while closing, the
movement stops.

12

*

Input congured as Bar CL, safety edge with inversion active only while closing. If while opening, the mo­vement stops.

13

*

Input congured as Bar CL TEST, safety edge tested with inversion active only while closing. If while opening,
the movement stops.

14

*

Input congured as Bar CL 8k2, safety edge with inversion active only while closing. If while opening, the
movement stops.

IC 1

Conguration of
command input

IC 1.

61

0

0 Input congured as Start E.

1 Input congured as Start I.

2 Input congured as Open.

3 Input congured as Close.

IC 2

Conguration of
command input

IC 2.

62

4

4 Input congured as Ped.

5 Input congured as Timer.

6 Input congured as Timer Pedestrian.

AUX 0

Conguration of

AUX 0 output.

20-21

6

0 Output congured as 2nd Radio Channel.

1 Output congured as SCA (gate open light).

2 Output congured as Courtesy Light command.

3 Output congured as Zone Light command.

4 Output congured as Stair Light

AUX 3

Conguration of

AUX 3 output.

26-37

0

5 Output congured as Alarm

6 Output congured as Flashing light

7 Output congured as Latch

8 Output congured as Magnetic lock

9 Output congured as Maintenance

10 Output congured as Flashing Light and Maintenance.

FIXED CODE

Fixed code 0

0

Receiver is congured for operation in rolling-code mode.
Fixed-Code Clones are not accepted.

1

Receiver is congured for operation in xed-code mode.
Fixed-Code Clones are accepted.

30 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

ENGLISH

INSTALLATION MANUAL

Logic Denition

De-

fault

Cross out

setting

used

Optional extras

Protection

level

Setting the

protection level

0

0

A - The password is not required to access the programming menus
B - Enables wireless memorizing of transmitters.
Operations in this mode are carried out near the control panel and do not require access:

- Press in sequence the hidden key and normal key (T1-T2-T3-T4) of a transmitter that has already been
memorized in standard mode via the radio menu.

- Press within 10 sec. the hidden key and normal key (T1-T2-T3-T4) of a transmitter to be memorized.
The receiver exits programming mode after 10 sec.: you can use this time to enter other new transmitters
by repeating the previous step.
C - Enables wireless automatic addition of clones.
Enables clones generated with the universal programmer and programmed Replays to be added to the
receiver’s memory.
D - Enables wireless automatic addition of replays.
Enables programmed Replays to be added to the receiver’s memory.
E - The board’s parameters can be edited via the U-link network

1

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
No change in behaviour of functions B - C - D - E from 0 logic setting

2

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
B - Wireless memorizing of transmitters is disabled.
C - Wireless automatic addition of clones is disabled. No change in behaviour of functions D - E from 0 logic setting

3

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
B - Wireless memorizing of transmitters is disabled.
D - Wireless automatic addition of Replays is disabled.
No change in behaviour of functions C - E from 0 logic setting

4

A - You are prompted to enter the password to access the programming menus
The default password is 1234.
B - Wireless memorizing of transmitters is disabled.
C - Wireless automatic addition of clones is disabled.
D - Wireless automatic addition of Replays is disabled.
E - The option of editing the board’s parameters via the U-link network is disabled.
Transmitters are memorized only using the relevant Radio menu.
IMPORTANT: This high level of security stops unwanted clones from gaining access and also stops radio
interference, if any.

SERIAL MODE

Serial mode

(Identies how

board is congured

in a BFT network

connection).

0

0 Standard SLAVE: board receives and communicates commands/diagnostics/etc.

1 Standard MASTER: board sends activation commands (START, OPEN, CLOSE, PED, STOP) to other boards.

2

SLAVE opposite leaves in local network : the control unit is the slave in an opposite leaves network with no
smart module (g.P)

3

MASTER opposite leaves in local network: the control unit is the master in an opposite leaves network with
no smart module (g.P)

ADDRESS

Address 0

[ ___ ]

Identies board address from 0 to 119 in a local BFT network connection.
(see U-LINK OPTIONAL MODULES section)

EXPI1

Conguration of

EXPI1 input on

input-output ex-

pansion board.

1-2

1

0 Input congured as Start E command.

1 Input congured as Start I command.

2 Input congured as Open command.

3 Input congured as Close command.

4 Input congured as Ped command.

5 Input congured as Timer command.

6 Input congured as Timer Pedestrian command.

7 Input congured as Phot (photocell) safety.

8 Input congured as Phot op safety (photocell active during opening only).

9 Input congured as Phot cl safety (photocell active during closing only).

10 Input congured as Bar safety (safety edge).

11

*

Input congured as safety Bar OP, safety edge with inversion active only while opening, if while closing the
movement stops.

12

*

Input congured as safety Bar CL, safety edge with inversion active only while closing, if while opening the
movement stops.

13

*

Input congured as Phot test safety, tested photocell. Input 3 (EXPI2) on input/output expansion board is
switched automatically to safety device test input, EXPFAULT1.

14

*

Input congured as Phot op test safety, tested photocell active only while opening. Input 3 (EXPI2) on input/
output expansion board is switched automatically to safety device test input, EXPFAULT1

15

*

Input congured as Phot cl test safety, tested photocell active only while closing. Input 3 (EXPI2) on input/
output expansion board is switched automatically to safety device test input, EXPFAULT1

16

*

Input congured as Bar safety, tested safety edge. Input 3 (EXPI2) on input/output expansion board is switched
automatically to safety device test input, EXPFAULT1.

17

*

Input congured as safety Bar OP test, safety edge with inversion active only while opening, if while closing
the movement stops. Input 3 (EXPI2) on input/output expansion board is switched automatically to safety
device test input, EXPFAULT1.

18

*

Input congured as safety Bar CL test, safety edge with inversion active only while closing, if while opening
the movement stops. Input 3 (EXPI2) on input/output expansion board is switched automatically to safety
device test input, EXPFAULT1.

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

- 31

D812201 00100_03

INSTALLATION MANUAL

Logic Denition

De-

fault

Cross out

setting

used

Optional extras

EXPI2

Conguration of

EXPI2 input

on input-output

expansion board.

1-3

0

0 Input congured as Start E command.

1 Input congured as Start I command.

2 Input congured as Open command.

3 Input congured as Close command.

4 Input congured as Ped command.

5 Input congured as Timer command.

6 Input congured as Timer Pedestrian command.

7 Input congured as Phot (photocell) safety.

8 Input congured as Phot op safety (photocell active during opening only).

9 Input congured as Phot cl safety (photocell active during closing only).

10 Input congured as Bar safety (safety edge).

11

*

Input congured as safety Bar OP, safety edge with inversion active only while opening, if while closing the
movement stops.

12*

Input congured as safety Bar CL, safety edge with inversion active only while closing, if while opening the
movement stops.

EXPO1

Conguration of

EXPO2 output

on input-output

expansion board

4-5

11

0 Output congured as 2

nd

Radio Channel.

1 Output congured as SCA (gate open light).

2 Output congured as Courtesy Light command.

3 Output congured as Zone Light command.

4 Output congured as Stair Light.

EXPO2

Conguration of

EXPO2 output

on input-output

expansion board

6-7

11

5 Output congured as Alarm.

6 Output congured as Flashing light.

7 Output congured as Latch.

8 Output congured as Magnetic lock.

9 Output congured as Maintenance.

10 Output congured as Flashing Light and Maintenance.

11

Output congured as Trac Light control with TLB board.

TRAFFIC

LIGHT PRE-

FLASHING.

Trac light pre-

ashing

0

0

Pre-ashing switched o.

1

Red lights ash, for 3 seconds, at start of operation.

TRAFFIC LIGHT

RED LAMP

ALWAYS ON

Steadily lit red

light

0

0

Red lights o when gate closed.

1

Red lights on when gate closed.

* Only active on FW ≥ 2.10

TABLE “C”  RADIO MENU RADIO

Logic Description

Add start

Add Start Key

associates the desired key with the Start command

add 2ch

Add 2ch Key

Associates the desired key with the 2nd radio channel command. If no output is congured as 2nd Radio Channel Output, the 2nd radio chan­nel controls the pedestrian opening.

erase 64

Erase List

WARNING! Erases all memorized transmitters from the receiver’s memory.

Read receiver code

Displays receiver code required for cloning transmitters.

ON = Enables remote programming of cards via a previously memorized W LINK transmitter.
It remains enabled for 3 minutes from the time the W LINK transmitter is last pressed.
OFF= W LINK programming disabled.

32 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03

MANUALE D’USO: MANOVRA MANUALE/ USER’S MANUAL: MANOVRA MANUALE/ MANUEL D’UTILISATION: MANOVRA MANUALE/ BE-

DIENUNGSANLEITUNG: MANOVRA MANUALE/ MANUEL DE USO: MANOVRA MANUALE/ MANUAL PARA DE USO: MANOVRA MANUALE

FIG. 3

C

B

E

click

D

A

(180°)

OPEN

(180°)

CLOSE

ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500 - 73

D812201 00100_03

AVVERTENZE PER L’UTILIZZATORE ( I )

ATTENZIONE! Importanti istruzioni di sicurezza.
Leggere e seguire attentamente le Avvertenze
e le Istruzioni che accompagnano il prodotto
poiché un uso improprio può causare danni a
persone, animali o cose. Conservare le istruzioni
per consultazioni future e trasmetterle ad even­tuali subentranti nell’uso dell’impianto.
Questo prodotto dovrà essere destinato solo
all’uso per il quale è stato espressamente insta­llato. Ogni altro uso è da considerarsi improprio
e quindi pericoloso. Il costruttore non può essere
considerato responsabile per eventuali danni
causati da usi impropri, erronei e irragionevoli.
SICUREZZA GENERALE

Nel ringraziarVi per la preferenza accordata a questo
prodotto, la Ditta è certa che da esso otterrete le
prestazioni necessarie al Vostro uso.
Questo prodotto risponde alle norme riconosciute
della tecnica e della disposizioni relative alla si­curezza se correttamente installato da personale
qualicato ed esperto (installatore professionale).
L’automazione, se installata ed utilizzata corretta­mente, soddisfa gli standard di sicurezza nell’uso.
Tuttavia è opportuno osservare alcune regole di
comportamento per evitare inconvenienti acci­dentali:

- Tenere bambini, persone e cose fuori dal raggio
d’azione dell’automazione, in particolare durante
il movimento.

- Non permettere a bambini di giocare o sostare nel
raggio di azione dell’automazione.

- L’apparecchio può essere utilizzato da bambini di
età non inferiore a 8 anni e da persone con ridot­te capacità siche, sensoriali o mentali, o prive di
esperienza o della necessaria conoscenza, purché
sotto sorveglianza oppure dopo che le stesse
abbiano ricevuto istruzioni relative all’uso sicuro
dell’apparecchio e alla comprensione dei pericoli
ad esso inerenti. I bambini non devono giocare con
l’apparecchio. La pulizia e la manutenzione desti­nata ad essere eettuata dall’utilizzatore non deve
essere eettuata da bambini senza sorveglianza.

- I bambini devono essere sorvegliati per sincerarsi
che non giochino con l’apparecchio. Non permet­tere ai bambini di giocare con i controlli ssi. Tenere
i telecomandi lontani dai bambini.

-

Evitare di operare in prossimità delle cerniere o organi
meccanici in movimento.

-

Non contrastare il movimento dell’anta e non ten­tare di aprire manualmente la porta se non è stato
sbloccato l’attuatore con l’apposita manopola di
sblocco.

-

Non entrare nel raggio di azione della porta o can­cello motorizzati durante il loro movimento.

- Non lasciare radiocomandi o altri dispositivi di
comando alla portata dei bambini onde evitare
azionamenti involontari.

- L’attivazione dello sblocco manuale potrebbe
causare movimenti incontrollati della porta se in
presenza di guasti meccanici o di condizioni di
squilibrio.

- In caso di apritapparelle: sorvegliare la tapparella
in movimento e tenere lontano le persone nché
non è completamente chiusa. Porre cura quando si
aziona lo sblocco se presente, poiché una tapparella
aperta potrebbe cadere rapidamente in presenza
di usura o rotture.

-

La rottura o l’usura di organi meccanici della porta

(parte guidata), quali ad esempio cavi, molle, sup­porti, cardini, guide.. potrebbe generare pericoli. Far
controllare periodicamente l’impianto da personale
qualicato ed esperto (installatore professionale)
secondo quanto indicato dall’installatore o dal
costruttore della porta.

- Per ogni operazione di pulizia esterna, togliere
l’alimentazione di rete.

- Tenere pulite le ottiche delle fotocellule ed i dispo­sitivi di segnalazione luminosa. Controllare che rami
ed arbusti non disturbino i dispositivi di sicurezza.

- Non utilizzare l’automatismo se necessita di
interventi di riparazione. In caso di guasto o di
malfunzionamento dell’automazione, togliere
l’alimentazione di rete sull’automazione, astenersi
da qualsiasi tentativo di riparazione o intervento
diretto e rivolgersi solo a personale qualicato ed
esperto (installatore professionale) per la neces­saria riparazione o manutenzione. Per consentire
l’accesso, attivare lo sblocco di emergenza (se
presente).

-

Per qualsiasi intervento diretto sull’automazione o
sull’impianto non previsto dal presente manuale,
avvalersi di personale qualicato ed esperto (insta­llatore professionale).

- Con frequenza almeno annuale far verifi­care l’integrità e il corretto funzionamento
dell’automazione da personale qualificato ed
esperto (installatore professionale), in particolare
di tutti i dispositivi di sicurezza.

- Gli interventi d’installazione, manutenzione e
riparazione devono essere documentati e la
relativa documentazione tenuta a disposizione
dell’utilizzatore.

- Il mancato rispetto di quanto sopra può creare
situazioni di pericolo.

DEMOLIZIONE

L’eliminazione dei materiali va fatta rispettan-

do le norme vigenti. Non gettate il vostro
apparecchio scartato, le pile o le batterie usate
nei riuti domestici. Avete la responsabilità di
restituire tutti i vostri riuti da apparecchia­ture elettriche o elettroniche lasciandoli in
un punto di raccolta dedicato al loro riciclo.

Tutto quello che non è espressamente previs­to nel manuale d’uso, non è permesso. ll buon
funzionamento dell’operatore è garantito solo
se vengono rispettate le prescrizioni riportate
in questo manuale. La Ditta non risponde dei
danni causati dall’inosservanza delle indicazioni
riportate in questo manuale.
Lasciando inalterate le caratteristiche essenziali
del prodotto, la Ditta si riserva di apportare in
qualunque momento le modiche che essa ritie­ne convenienti per migliorare tecnicamente, cos­truttivamente e commercialmente il prodotto,
senza impegnarsi ad aggiornare la presente
pubblicazione.

USER WARNINGS (GB)

WARNING! Important safety instructions. Ca­refully read and comply with the Warnings and
Instructions that come with the product as impro­per use can cause injury to people and animals
and damage to property. Keep the instructions
for future reference and hand them on to any
new users.
This product is meant to be used only for the

D811767_07

74 - ARES ULTRA BT A 1000 - ARES ULTRA BT A 1500

D812201 00100_03