OWNER/OPERATOR
MANUAL
NOTICIA IMPORTANTE
Este manual contiene importantes instrucciones de seguridad que deben ser seguidas el pie de la letra cuando utilice esta maquina.
MODELS
909A & 919A
SLICERS
IMPORTANT NOTICE
This manual contains Important Safety Instructions which must be strictly followed when using this equipment.
909A & 919A OWNER/OPERATOR MANUAL • 23
BEFORE USING THIS EQUIPMENT
Berkel’s slicers are designed to slice meat and other food products safely and efficiently. However, unless the operator is properly trained and supervised, there is the possibility of a serious injury. It is the responsibility of the owner to ensure that this slicer is used properly and safely, strictly following the instructions contained in this manual and any requirements of local law.
No one should use or service this slicer without proper training and supervision. All operators should be thoroughly familiar with the procedures contained in this manual. Even so, Berkel cannot anticipate every circumstance or environment in which its slicers will be used. You, the owner and operator, must remain alert to the hazards posed by the function of a slicer—particularly the sharp rotating blade and moving table. No one under 18 years of age should operate this equipment. If you are uncertain about a particular task, ask your supervisor.
This manual contains a number of safe practices in the General Safety Instruction Section. Additional warnings are placed throughout this manual. WARNINGS RELATED TO YOUR PERSONAL SAFETY
ARE INDICATED BY:
WARNING
If any warning label, wall chart or manual becomes misplaced, damaged or illegible, please contact your nearest distributor or Berkel directly, for a free replacement.
Remember, however, THIS MANUAL OR THE WARNING LA-
BELS DO NOT REPLACE THE NEED TO BE ALERT AND TO USE YOUR COMMON SENSE WHEN USING THIS SLICER.
22 • 909A & 919A OWNER/OPERATOR MANUAL
|
T ABLE OF C ONTENTS |
|
Page |
General Safety Instructions |
.................................................................................................................. 2 |
Equipment Description ......................................................................................................................... |
4 |
Installation ............................................................................................................................................ |
6 |
Assembly .............................................................................................................................................. |
7 |
Testing Prior to Operation .................................................................................................................... |
8 |
Operating Instructions ........................................................................................................................ |
10 |
Sharpener Maintenance ...................................................................................................................... |
12 |
Cleaning and Sanitizing ....................................................................................................................... |
13 |
Sharpening .......................................................................................................................................... |
16 |
Optional Accessories .......................................................................................................................... |
17 |
Troubleshooting .................................................................................................................................. |
18 |
Repair Parts/Repair Service ................................................................................................................ |
19 |
Specifications ...................................................................................................................................... |
20 |
Warranty ............................................................................................................................................. |
21 |
The Berkel Company • World’s Leading Manufacturer of Slicer and Food Processing Equipment
BERKEL COMPANY
4406 Technology Drive · South Bend, Indiana 46628-9770
574/232-8222 · Fax 574/232-8116
(800) 348-0251
Form No. OM900A-0902N |
Printed in USA |
Berkel Company |
Part No. 3175-00926 |
909A & 919A OWNER/OPERATOR MANUAL • 1
PELIGRO
CUCHILLA FILOSA para evitar serios accidentes a su persona siga las instrucciones de este manual y
1.NUNCA utlice esta mçquina sin previa instrucciùn y autorizaciùn de su supervisor.
2.LA MçQUINA DEBE apoyarse sobre un nivel solido y plano.
3.LOS PROTECTORES deben colocarse ANTES de enchufar y operar la mçquina.
4.SIEMPRE utilice el enchufe original proveido por el fabricante.
5.SIEMPRE utilice el utensillo para empujar la comida - nunca su mano.
6.NUNCATOQUE LACUCHILLACON LA MANO.
7.MANTENGA manos, brazos, cabello y
ropa suelta LEJOS de toda parte en movimiento de la mçquina.
8.EN CASO DE QUE LA MÇQUINA SE TRABE, apague y desconecte ANTES de sacar lo que la obstruye.
9.APAGUE Y DESCONECTE LA MçQUINA antes de limpiar, sanitizar, o arreglar.
10.UTILIZE UNICAMENTE los repuestos provistos por el fabricante.
11.EN CASO de que los membretes de ‘PELIGRO’ se desprendan de la mçquina o sean illegibles, llame al fabricante o a su representante de service Berkel para que lo reemplace sin cargo.
2 • 909A & 919A OWNER/OPERATOR MANUAL
WARNING
SHARP KNIFE BLADE to avoid serious personal injury
follow all the instructions in this manual and
1.NEVER touch this machine without training and authorization by your supervisor.
2.MACHINE MUST BE on solid level support.
3.GUARDS MUST BE in place before plugging in and turning on machine.
4.ALWAYS use three pronged plug provided.
5.ALWAYS use food pusher not your hand.
6.NEVER TOUCH ROTATING KNIFE.
7.KEEP hands, arms, hair and loose clothing clear of all moving parts.
8.SHOULD MACHINE JAM, turn off and unplug before removing obstruction.
9.TURN OFF AND UNPLUG machine from power source before cleaning, sanitizing or servicing.
10.USE ONLY the attachments provided by the manufacturer.
11.SHOULD any warning label on a machine come off or become unreadable, contact the manufacturer or your Designated Berkel Service Location for a free replacement.
909A & 919A OWNER/OPERATOR MANUAL • 3
EQUIPMENT DESCRIPTION
Pusher
Slide Bar
Center Plate
Pusher Pusher
Hooks
Sharpener
Product Table
Handle
4 • 909A & 919A OWNER/OPERATOR MANUAL
EQUIPMENT DESCRIPTION
Center Plate
Locking Knob
Slice Deflector
Gauge Plate
Product Table
Thickness
Control Knob
HI/LOW
Switch
Shift Lever |
ON/OFF |
Switch |
909A & 919A OWNER/OPERATOR MANUAL • 5