Beko WMXD 760 S, WMXD 760 W User Manual
installation & operating
instructions and washing guidance
Automatic
washing machine
WMXD 760 W
WMXD 760 S
a
s
w
w
e
n
g
e
t
t
h
e
b
e
t
s
m
o
r
f
r
u
o
y
h
e
r
Please read this manual first!
Dear Customer,
We hope that your product which has been manufactured in modern facilities
and passed through a strict quality control procedure will give you the best
results.
Therefore, we advise you to read through this manual carefully before using
your product and keep it for future reference.
This operation manual will…
…help you use your machine in a fast and safe way.
• Please read the Operation Manual before installing and starting your
machine.
• Particularly follow the instructions related to safety.
• Keep this Operating Manual within easy reach. You may need it in the
future.
• Please read all additional documents supplied with this machine.
Please note that this Operating Manual may be applicable for several other
models. Differences between models will be identified in the manual.
Explanation of symbols
Throughout this Operation Manual the following symbols are used:
Important information or useful hints about usage.
C
Warning for hazardous situations with regard to life and property.
A
Warning for supply voltage.
B
This appliance’s packaging material is recyclable. Help recycle it and protect
the environment by dropping it off in the municipal receptacles provided for this
purpose. Your appliance also contains a great amount of recyclable material.
It is marked with this label to indicate the used appliances that should not be
mixed with other waste. This way, the appliance recycling organised by your
manufacturer will be done under the best possible conditions, in compliance
with European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment. Contact your town hall or your retailer for the used appliance
collection points closest to your home. We thank you doing your part to
protect the environment.
TABLE OF CONTENTS
1 Your Washing Machine 4
Overview 4
Specifications 5
2 Warnings 6
General Safety 6
First Use 6
Intended use 6
Safety instructions 6
If there are children in your house... 7
Electrical connection 7
3 Installation 9
Removing packaging reinforcement 9
Opening the transportation locks 9
Appropriate installation location
Adjusting the feet 9
Connecting to the water supply. 1
Connecting to the drain 1
Electrical connection 1
Destroying the packaging material 1
Disposing of the old machine 11
4 Initial preparations for
washing 12
Sorting the laundry 12
Preparing clothes for washing 12
Correct load capacity 1
Loading door 1
Detergents and softeners 1
Extra Rinse 18
Program selection and consumption
table 18
Auxiliary functions 19
Time display 19
Starting the Program 20
Progress of program 2
Changing the selections after the
program has started 20
Child-proof lock 20
End of program 21
Ending the program through cancelling
21
6 Quick instructions for
daily use 22
9
7 Cleaning and care 2
0
Detergent drawer 23
0
The door and the drum 2
1
Outer cabinet and control panel 2
1
Inlet water filters 2
Draining any remaining water and
cleaning the pump filter 24
8 Troubleshooting 26
9 Guarantee 3
2
3
10 Service 3
3
0
3
3
3
3
2
3
5 Selecting a program and
operating your machine 15
Turning the machine on 16
Program selection 16
Main programs 16
Additional programs 1
Special programs 17
Spin Speed selection 17
6
1 Your Washing Machine
1
2
3
4
5
6
Overview
Figure 1
1
Top Lid
2
Detergent Drawer
Control Panel
3
4
Height-adjustable Feet
5
Door
Filter Cap
6
EN
4
Specifications
Models
Maximum dry laundry capacity (kg)
Height (cm)
Width (cm)
Depth (cm)
Net Weight (kg)
Electricity (V/Hz.)
Total Current (A)
Total Power (W)
Spinning cycle (rpm max.)
WMXD 760 W
WMXD 760 S
7
84
60
59
76
230/50
10
2200
1600
Specifications of this appliance may change without notice to improve the quality of
the product. Figures in this manual are schematic and may not match your product
exactly.
Values stated on the machine labels or in the documentation accompanying it are
obtained in laboratory in accordance with the relevant standards. Depending on
operational and environmental conditions of the appliance, values may vary.
EN
5
2 Warnings
Please read the following information.
Otherwise, there may be the risk of
personal injury or material damage.
Moreover, any warranty and reliability
commitment will become void.
General Safety
• Never place your machine on a
carpet covered floor. Otherwise, lack
of airflow from below your machine
may cause electrical parts to
overheat. This may cause problems
with your washing machine.
• If the power cable or mains plug is
damaged you must call Authorized
Service for repair.
• Check water hoses for wear. Do
not use old/used water inlet hoses.
These may cause stains on your
laundry.
• Fit the drain hose into the waste
water system securely to prevent
any water leakage and to allow
machine to take in and discharge
water as required. It is very
important that the water intake
and drain hoses are not folded,
squeezed, or broken when the
appliance is pushed into place after
it is installed or cleaned.
• Your washing machine is designed
not to continue operating in the
event of a power interruption. You
cannot cancel any program by
pressing the “On/Off button.” Your
machine will not resume its program
when the power restores. Press
the “Start/Pause/Cancel” button for
3 seconds to cancel the program
(See, Cancelling a Program)
• There may be some water in your
machine when you receive it. This is
from the quality control process and
is normal. It is not harmful to your
machine.
• Some problems you may encounter
may be caused by the software.
Press "Start/Pause/Cancel" button
for 3 seconds to cancel the program
set in your machine before calling
the authorized service.
First Use
• To prepare your machine for
washing, carry out your first washing
process without loading your
machine and with detergent under
“Cottons 90°C” program.
• Ensure that the cold water
connections has been made
correctly when installing your
machine.
• If the current fuse or circuit breaker
is less than 15 Amperes, please
have a qualified electrician install a
15 Ampere fuse or circuit breaker.
• To make your machine ready for
use, please be sure that the tap
water supply and water drainage
systems are appropriate before
calling the authorized service. If they
are not, call a qualified plumber to
have any necessary arrangements
carried out.
Intended use
• This product has been designed for
home use.
• The appliance may only be used for
washing and rinsing of textiles that
are marked accordingly.
• Only detergents, softeners and
supplements suitable for washing
machines may be used.
• Observe the care instructions
labelled on textile products and
any other instructions given by
companies that produce detergents
for your machine.
Safety instructions
• This appliance must be connected
to an earthed outlet protected by a
fuse of suitable capacity.
• The supply and draining hoses must
always be securely fastened and
EN
6
remain in an undamaged state.
• Fit the draining hose to a washbasin
or waste system securely before
starting up your machine. There may
be a risk of being scalded due to
high washing temperatures!
• Never open the door or remove the
filter while there is still water in the
drum. Otherwise, there may be the
risk of flooding and possible injury
due to the hot water.
• Never force open the locked door!
The door will be ready to open just a
few minutes after the washing cycle
comes to an end.
• Unplug the machine when it is not in
use.
• Never wash down the appliance
with a water hose! There is the risk
of electric shock! Always disconnect
from the mains by unplugging before
cleaning.
• Never touch the plug with wet
hands. Never unplug by pulling
on the cable, always pull out from
the plug only. Do not operate the
machine if the power cord or plug is
damaged.
• Never attempt to repair the machine
yourself. Otherwise, you may be
putting yours and other's lives in
danger.
• For malfunctions that cannot
be solved by information in the
operating manual:
Turn off the machine, unplug it, turn
off the water tap and contact an
authorized service agent.
If there are children in your
house...
• Electrical appliances may be
dangerous for the children. Keep
children away from the machine
when it is operating. Do not let them
tamper with the machine.
• Close the door when you leave the
area where the machine is located.
• Store all detergents in a safe place
out of reach of the children.
Electrical connection
Make sure that you have an earthed
power outlet socket rated at 13 amps
(minimum).
Attention!
If you use your machine as built-in,
the socket must be reachable after
installation, or a separate switch (which
can disconnect the two poles) must be
used in the installation.
Connect the power cord to the
appropriate electrical socket with an
equivalent current rating indicated on the
rating plate at the front of the machine
behind the kick plate.
After removing the plug from its transit
position, please insert the plug seal
to prevent water spillage entering the
machine.
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket in a
readily accessible position.
Should the mains lead of the appliance
become damaged or need replacing
at any time, it must be replaced by a
special purpose made mains lead which
can only be obtained from a Authorised
Service Agent.
This appliance must be earthed
B
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as
a plug with a bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse
need to be replaced an ASTA approved
BS1362 fuse of the same rating must
be used. Do not forget to refit the fuse
cover. In the event of losing the fuse
EN
7
cover, the plug must not be used until a
replacement fuse cover has been fitted.
Colour of the replacement fuse cover
must be the same colour as that visible
on the pin face of the plug. Fuse covers
are available from any good electrical
store.
Important
Fitting a different plug
As the colours of the wires in the
mains lead of this appliance may not
correspond with the coloured markings
identifying the terminals on your plug,
proceed as follows:
1 Connect the green - yellow or green
(earth) wire to the terminal in the
plug marked ‘E’ or with the symbol
f or coloured green and yellow or
green.
2 Connect the blue (neutral) wire to the
terminal in the plug marked ‘N’ or
coloured black.
3 Connect the brown (live) wire to the
terminal in the plug marked ‘L’ or
coloured red.
With the alternative plugs a 13A fuse
must be fitted either in the plug or
adaptor or in the main fuse box. If in
doubt contact a qualified electrician.
EN
8
3 Installation
Removing packaging
reinforcement
Tilt the machine to remove the
packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
Opening the transportation
locks
Transportation safety bolts must
C
be removed before operating the
washing machine! Otherwise, the
machine will be damaged!
1. Loosen all the bolts with a spanner
until they rotate freely (“C”)
2. Remove transportation safety bolts
by turning them gently.
3. Fit the covers (supplied in the bag
with the Operation Manual) into the
holes on the rear panel. (“P”)
Keep the transportation safety
C
bolts in a safe place to reuse when
the washing machine needs to be
moved again in the future.
Never move the appliance without
C
the transportation safety bolts
properly fixed in place!
Appropriate installation
location
Install the appliance in environments
which have no risk of freezing, in a
stable and level position.
The floor must be capable of
C
carrying the load on it!
If the washing machine and a drier
C
are placed on top of each other,
their approximate weight together
may reach 180 kg when they are
full.
Important:
• Do not place the appliance on top of
the power cable.
• Keep at least 1cm distance from the
edges of other furniture.
• Place the machine on a firm surface;
do not position it on a long pile rug
or such like surfaces.
Adjusting the feet
Do not use any tools to loosen the
C
lock nuts. Otherwise, they can be
damaged.
1. Manually (by hand) loosen the lock
nuts on the feet.
EN
9
2. Adjust them until the machine
stands level and firm.
3. Important: Tighten all lock nuts up
again.
Connecting to the water
supply.
Important:
• The water supply pressure required
to run the machine must be 1-10
bar (0,1 – 10 MPa). (Practically, it
is necessary to have 10 – 80 liters
of water flowing from the tap in
one minute to have your machine
run smoothly.) Attach a pressurereducing valve if the water pressure
is higher.
• Connect the special hose supplied
with the machine to the water intake
valves on the machine.
must be attached to the machine.
Tighten the nuts of the hose well by
hand; never use wrenches to tighten
the nuts.
• Open the taps completely after
making the hose connection to
check if there is any water leakage
at the connection points. Turn off
the tap and remove the nut in case
of any leakage. Retighten the nut
carefully after checking the seal.
To prevent any water leakage and
any other damage to be caused by
it, keep the taps closed when the
machine is not in use.
• Models with a single water inlet
should not be connected to the
hot water tap. Laundry may be
damaged or the appliance may
switch to protection mode and not
work.
• In order to prevent water leakage
that may occur at the connection
points, there are rubber seals (4
seals for the models with double
water inlet and 2 seals for other
models) attached to the hoses.
These seals should be used at the
tap and machine connection ends of
the hoses. The plain end of the hose
fitted with a filter must be attached
to the tap and the elbowed end
When returning the appliance to its
place after maintenance or cleaning,
care should be taken not to fold,
squeeze or block the hoses.
Connecting to the drain
The water discharge hose can be
attached to the edge of a washbasin
or waste water system. The drain hose
should be firmly fitted into the drain as
to not loosen in its housing.
Important:
• The end of the drain hose can
be directly connected to the
wastewater drain or to the
washbasin. The fitting must be
secured in all types of connections.
EN
10
Your house may be flooded if the
hose falls out of its housing during
water discharging.
• The hose should be attached to a
height of at least 40 cm, and 100
cm at most.
• In case the hose is elevated
after laying it on the floor level or
close to the ground (less than
40 cm above the ground), water
discharge becomes more difficult
and the laundry may come out wet.
Therefore, the heights described in
the figure should be followed.
• To prevent dirty water refilling the
machine, and to allow for easy
discharge, the end of the hose
must not be submerged in the drain
water. The end of the hose must be
able to take in air. The hose should
be pushed into the drainage for
more than 15 cm. If it is too long
you may have it shortened.
• The end of the hose should not be
bent, it should not be stepped on
and it must not be folded between
the drain and the machine.
• The length of the hose is too short,
you may add an extension hose
to the original section. The length
of the hose must not be longer
than 3.2 m after coming out of the
machine. To avoid water leakage
failures, the connection between the
extension hose and the drain hose
of the product must be fitted well
with an appropriate clamp as not to
come off and leak.
Electrical connection
Connect the machine to an earthed
outlet protected by a fuse of suitable
capacity.
Important:
• Connection should comply with
national regulations.
• Power cord plug must be within
easy reach after installation.
• The voltage and the allowed fuse
protection are specified in the
section “Technical Specifications”.
• The specified voltage must be equal
to your mains voltage.
• Connection via extension cords or
multi-plugs should not be made.
A damaged power cable must be
B
replaced by a qualified electrician.
The appliance must not be operated
B
whilst faulty until it as been repaired!
There is the risk of electric shock!
Destroying the packaging
material
Packaging material can be dangerous to
children. Keep the packaging materials
out of reach of children or dispose
them by classifying according to waste
directives. Do not dispose of them
together with normal domestic waste.
Packaging materials of your machine are
manufactured from recyclable materials.
Disposing of the old machine
Dispose of your old appliance in an
environmental friendly manner.
• You may refer to your local agent or
solid waste collection center in your
municipality to learn how to dispose
of your machine.
Before disposing of your old washing
machine, cut off the mains plug and
make the door lock unusable.
11
EN
Loading...