Washer-Dryer |
User’s Manual |
WDA 105614 |
EN |
Document Number= 2820524451/07-02-17.(16:02) |
This product was manufactured using the latest technology in environmentally friendly conditions.
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
CAUTION
¾¾ This product can be used by children at and above 8 years old and by persons whose physical, sensory or A mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and maintenance works which can be done by users should not be performed by
children unless they are supervised by someone.
CAUTION
A ¾¾ Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
NOTE
C ¾¾ Always have the installation and repairing procedures carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
1.1.1 Electrical safety
DANGER
B ¾¾ If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent. There is the risk of electric shock!
¾¾ Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
A |
CAUTION |
¾¾ If the power cable is damaged, it must be replaced by the manufacturer, after-sales service or a similarly |
|
qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible |
|
|
risks. |
A |
|
CAUTION |
¾¾ Unplug the product when not in use. |
||
¾¾ |
Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug. |
|
|
¾¾ Unplug the product during installation, maintenance, cleaning and repairing procedures. |
|
|
¾¾ |
Do not make connections via extension cables or multi-plugs. |
NOTE
C ¾¾ This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.
User’s Manual |
3 / EN |
|
|
Important instructions for safety and environment
1.1.2 Product safety
DANGER
A ¾¾ Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and scalds from hot water will occur.
CAUTION
A ¾¾ The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
NOTE
¾¾ Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle is completed. The loading door will not open if the machine is not cooled down enough after the programme. You can ensure a faster cool down of the machine by running a 10-minute drying programme, or wait until it cools down by
C itself. Do not force the loading door open. The door and the lock mechanism can get damaged.
¾¾ There should not be any lockable, sliding or hinged door that may restrain the loading door to open fully in the installation place of this product.
¾¾ Follow the instructions on the textile tags and on the detergent package.
¾¾ Only detergents, softeners and supplements suitable for washing machines should be used. ¾¾ Do not install or leave this product in places where it will be exposed to weather conditions. ¾¾ Controls should not be tampered with.
1.1.3 Warnings for dryer
DANGER
¾¾ As the laundry which had been cleaned, washed, soiled or stained with benzine/diesel oil, dry cleaning solvents or other combustible and explosive materials before will emit flammable or explosive vapour, they should not be dried in the machine. This may cause risk of fire.
¾¾ Clothes soiled with liquid cooking oil, acetone, alcohol, benzine, gas oil, stain remover, turpentine, waxes or wax removers must be washed with hot water and plenty of detergent before they are dried. This may cause risk of fire.
¾¾ Clothes or pillows supported by rubber foam (latex foam), shower caps, water-repellent textile products, rubber supported materials and rubber foam pads should not be dried in the machine. This may cause risk of fire.
¾¾ If you use Washing Balls, Detergent Scales, Laundry Cages or Balls while washing in your appliance, these may melt while drying. Do not use these products if drying will be selected. This may cause risk of fire.
¾¾ Never run the drying function when you are using industrial chemicals for cleaning. This may cause risk of fire.
DANGER
¾¾ Do not touch the door glass with bare hands after drying. This may cause risk of burn.
A ¾¾ To keep the laundry under a temperature at which they will not be damaged, a cooling step is carried out as the last stage. If you open the loading door before cooling step is completed, you may be exposed to hot vapour. This may cause risk of scalding.
¾¾ When drying programmes are interrupted (cancelling the programme or power cut), laundry in the machine may be hot. Be careful.
CAUTION
¾¾ Do not stop the machine before the drying programme is completed. If you have to stop it, take out all laundry promptly and spread them on somewhere appropriate where they can cool down.
A ¾¾ Do not dry tulle curtains, rugs and blankets in the machine.
¾¾ Your product is suitable to operate under ambient temperatures between 0°C and +35°C.
¾¾ Ambient temperatures between 15°C and +25°C are the ideal operating temperatures for your product. ¾¾ Pay care that pets do not enter into the product. Check inside of the product prior to use.
¾¾ Do not perform drying by overloading the machine. Follow the maximum load amounts specified for drying.
4 / EN |
Washer-Dryer |
|
|
Important instructions for safety and environment
CAUTION
¾¾ Drying should not be performed on leather garments or garments containing leather (e.g. leather jeans tags, etc.). Leather piece may colour.
¾¾ Turn off the machine in failures that cannot be eliminated by applying the information given in the safety instructions, then unplug it and call the Authorized Service Agent.
A ¾¾ It is possible only to wash the laundry or only to dry the laundry or perform both washing and drying in the washerdryer. Machine should not be used for drying for a long time only with damp load. If the machine is used only for drying, any of the short washing programmes should be run without putting in laundry after every 15 cycles.
¾¾ Control all clothes before loading the machine to make sure that no belongings such as lighter, coins, metal pieces, pins, etc have been left in the pockets or among them.
¾¾ Underwear with metal supports should not be dried in the machine. Metal supports may get loose and broken during drying process, thus cause damage on the cloth.
¾¾ Do not dry voluminous laundry such as duvet and alike in the machine. Otherwise, your laundry may get damaged.
NOTE
¾¾ Do not dry the unwashed laundry in the machine.
C ¾¾ Do not use fabric softeners or antistatic products in the machine unless these are recommended by their manufacturers. ¾¾ Fabric softeners and products alike should be used in accordance with the instructions of their producers.
¾¾ Do not dry delicate clothes such as silk, woollen, etc. in the machine. Otherwise, woollen clothes may shrink and become smaller and other delicate clothes may get damaged.
¾¾ Check the symbols on the product label on the garment prior to Drying and Washing processes.
1.2 Intended use
|
NOTE |
C |
¾¾ This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of |
its intended use. |
|
¾¾ Use the product only for washing, rinsing and drying of textile products that are marked accordingly. |
|
|
¾¾ The manufacturer waives any responsibility arisen from incorrect usage or transportation. |
|
¾¾ The service life of your product is 10 years. During this period, original spare parts will be available to operate the |
|
appliance properly. |
1.3 Children's safety |
|
|
CAUTION |
|
¾¾ Keep children under 3 years of age away from the appliance unless they are supervised. |
A |
¾¾ Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of |
the children. |
|
¾¾ Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do |
|
|
not let them to tamper with the product. Use child lock to prevent children from intervening with the product. |
|
¾¾ Do not forget to close the loading door when leaving the room where the product is located. |
|
¾¾ Store all detergents and additives in a safe place away from the reach of the children by closing the cover of |
|
the detergent container or sealing the detergent package. |
1.4 Compliance with WEEE Directive
¾¾ This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
¾¾ This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.
1.5 Package information
•PackagingmaterialsoftheproductaremanufacturedfromrecyclablematerialsinaccordancewithourNationalEnvironmentRegulations. Do not dispose of waste package together with domestic or other wastes. Dispose them at package collection points specified by the local authorities.
User’s Manual |
5 / EN |
|
|
2 |
|
Technical specifications |
|
|
|
|
|
|
|
|
|
|
|
|
Models |
|
WDA 105614 |
|
|
|
|
|
|
|
|
|
|
|
|
Maximum dry laundry capacity (kg) _Washing |
10.5 |
|
||
Maximum dry laundry capacity (kg)_Drying |
6 |
|
||
Height (cm) |
84 |
|
||
Width (cm) |
60 |
|
||
Depth (cm) |
63 |
|
||
Net weight (±4 kg.) |
86 |
|
||
Electrical input (V/Hz) |
230 V / 50 Hz |
|
||
Total current (A) |
10 |
|
||
|
|
|
|
|
Total power (W) |
2200 |
|
||
Spin speed (rpm max.) |
1400 |
|
||
NOTE
¾¾ Technical specifications may be changed without prior notice to improve the quality of the product. C ¾¾ Figures in this manual are schematic and may not match the product exactly.
¾¾ Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards. Depending on operational and environmental conditions of the product, these values may vary.
6 / EN |
Washer-Dryer |
|
|
3 Installation
Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and take care that the electricity,tap water supply and water drainage systems are appropriate before calling theAuthorized Service Agent.If they are not,call a qualified technician and plumber to have any necessary arrangements carried out.
B |
DANGER |
|
¾¾ |
Have the installation and electrical connections of the product made by the Authorized Service Agent. |
|
|
Manufacturer shall not be held liable for damages that may arise from procedures carried out by |
|
|
|
unauthorized persons. |
|
|
|
|
DANGER |
|
|
¾¾ Product The weight of your product is not suitable to be carried by one person. |
|
|
|
|
|
|
|
A |
CAUTION |
|
¾¾ |
Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged |
|
|
|
products cause risks for your safety. |
|
|
|
A |
CAUTION |
|
¾¾ Preparation of the location and electrical, tap water and waste water installations at the place of installation are |
||
|
under customer’s responsibility. |
|
|
¾¾ Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed |
|
|
|
while pushing the product into its place after installation or cleaning procedures. |
3.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
• Do not place the product on the power cable.
• Do not install the product at places where temperature may fall below 0ºC. (See,Warnings for drying)
• Place the product at least 1.5 cm away from the edges of other furniture.
• There should not be any lockable, sliding or hinged door that may restrain the loading door to open fully in the installation place of this product.
• Operate the product in a well-ventilated and dust-free environment.
3.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement.Remove the packaging reinforcement by pulling the ribbon.
|
DANGER |
|
¾¾ The product is heavy. Remove the packaging reinforcement as illustrated. |
|
¾¾ Pay attention not to squeeze your hand under the machine during this procedure. |
|
|
3.3 Removing the transportation locks |
|
|
|
A |
CAUTION |
¾¾ Do not remove the transportation locks before taking out the packaging reinforcement. |
|
¾¾ Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be |
|
|
damaged. |
User’s Manual |
7 / EN |
|
|
Installation |
|
|
1 |
2 |
3 |
1 Loosen all bolts with the tool supplied in the User Manual bag until they turn freely. (C) 2 Remove transportation safety bolts by turning them gently.
3 Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)
C |
|
NOTE |
¾¾ |
Keep the transportation safety bolts in a safe place to reuse when the machine needs to be moved again in the future. |
|
|
¾¾ |
Never move the product without the transportation safety bolts properly fixed in place! |
3.4 Flush usage with the bench
|
|
|
|
65,5 cm |
59,5 cm |
15 |
cm |
15 |
cm |
|
|
|
|
<![if ! IE]> <![endif]>86 cm |
|
||
| <![if ! IE]> <![endif]>20 cm |
<![if ! IE]> <![endif]>20 cm |
|
|||
|
<![if ! IE]> <![endif]>60 cm |
|
<![if ! IE]> <![endif]>60 cm |
|
84,0 cm |
|
|
|
|
|
|
|
|
66cm |
|
|
|
|
|
|
|
1,4 cm |
|
CAUTION
¾¾ Your machine should never be operated without the top plate.
A ¾¾ When the Washer-Dryer is placed under the bench, front of the machine should never be blocked by the cupboard door.
¾¾ When the Washer-Dryer is placed under the bench, air vents must be bored into the left and right sides of the cupboard.
|
NOTE |
C |
¾¾ Follow the above dimensions when installing the product under the bench. These dimensions are indispensable to avoid |
any change in the performance of your machine. |
|
¾¾ Drying washing machine can be used under a bench if the height of the bench allows. |
|
|
¾¾ At least 3 cm clearance must be left between the sides and the back of the product and the wall when it is installed under |
|
the bench or in a cupboard. |
3.5 Connecting water supply
NOTE
¾¾ The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have C 10 – 80 litres of water flowing from the fully open tap in one minute to have your machine run smoothly.Attach a pressure
reducing valve if water pressure is higher.
¾¾ If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied blind stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)
CAUTION
A ¾¾ Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.
¾¾ Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
8 / EN |
Washer-Dryer |
|
|
Installation
2
1Connect the special hoses supplied with the product to the water inlets on the product.Red hose (left) (max.90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.
CAUTION
A ¾¾ Ensure that the cold and hot water connections are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.
2 Tighten all hose nuts by hand. Never use a tool when tightening the nuts.
3Open the taps completely after making the hose connection to check for water leaks at the connection points.If any leaks occur,turn off the tap and remove the nut.Retighten the nut carefully after checking the seal.To prevent possible water leakages,keep the taps closed when the machine is not in use.
3.6 Connecting to the drain
• Connect the end of the drain hose directly to the wastewater drain, sink or to the washbasin.
A
min.40
CAUTION
¾¾ Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.
90
40
40 
•The distance to the wall so that the machine be placed up to 30 cm.
•Attach the hose at a height of at least 40 cm, and 90 cm at most.
•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet.Therefore, follow the heights described in the figure.
•To prevent flowing of waste water back into the machine and to allow for easy discharge, do not immerse the hose end into the waste water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.
•Pay care not to bend the end of the hose, step on it or pinch the hose between the drain and the machine.
•If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.
User’s Manual |
9 / EN |
|
|
Installation
3.7 Adjusting the feet
1 |
2 |
3 |
CAUTION
A ¾¾ In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.
1 Loosen the nuts on the feet in the direction of arrow with the tool supplied in the User Manual bag.
2Adjust the feet until the product stands level and balanced. You can move the feet downwards by turning them counterclockwise or upwards by turning clockwise.
3Tightenalllocknutsagaininthedirectionofarrowbythetoolsupplied.Youcanmovethenutsupwardsbyturningthemcounterclockwise or downwards by turning clockwise.
3.8Electrical connection
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
•Connection must comply with national regulations.
•Power cable plug must be within easy reach after installation.
•If the current fuse or circuit breaker is less than 16 Amperes, please have a qualified electrician install a 16 Ampere fuse or circuit breaker.
•The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
B |
DANGER |
¾¾ Damaged power cables must be replaced by the Authorized Service Agents. |
3.9 Transportation of the product
1 Unplug the product before transporting it.
2 Remove water drain and water supply connections.
3 Drain all water that has remained in the product. See. 6.6
4 Install transportation safety bolts in the reverse order of removal procedure; see 3.3.
DANGER
¾¾ The weight of your product is not suitable to be carried by one person.
¾¾ The product is heavy; it should be carried by two persons very carefully on the stairs. Falling of your product on you may cause disabilities.
CAUTION
A ¾¾ Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
C |
NOTE |
¾¾ Never move the product without the transportation safety bolts properly fixed in place! |
10 / EN |
Washer-Dryer |
|
|
|
4 |
|
Preparation |
4.1 |
Sorting the laundry |
||
• |
Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature. |
||
• |
Always obey the instructions given on the garment tags. |
||
4.2 |
Preparing laundry for washing |
||
•Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a cotton laundry bag or cotton pillow case. Moreover, such clothes may warm up excessively during drying and get damaged. For this reason, do not dry such laundry in the machine.
•Put small size clothes such as infant's socks and nylon stockings in a cotton laundry bag or cotton pillow case.
•Place curtains in without compressing them. Remove curtain attachment items. Do not dry tulle curtains in the machine.
•Fasten zippers, sew loose buttons and mend rips and tears.
•Wash “machine washable” or “hand washable” labeled products only with an appropriate programme. Do not dry such clothes in the machine; either hang or spread them to dry.
•Do not wash colours and whites together. New, dark coloured cottons release a lot of dye.Wash them separately.
•Use only dyes/colour changers and limescale removers suitable for machine wash.Always follow the instructions on the package.
NOTE
¾¾
C ¾¾¾¾
¾¾
¾¾
Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.
Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling. Wash trousers and delicate laundry turned inside out.
Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.
4.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
•Operate the product in the highest capacity allowed by the programme you have selected, but do not overload. See, “Programme and consumption table”.
•Always follow the instructions on the detergent packaging.
•Wash slightly soiled laundry at low temperatures.
•Use faster programmes for small quantities of lightly soiled laundry.
•Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
•If you plan to dry your laundry, select the highest spin speed recommended during washing process.
•Do not use detergent in excess of the amount recommended on the detergent package.
4.4 First use
Beforestartingtousetheproduct,makesurethatallpreparationsarecompletedinaccordancewiththeinstructionsinsections"Importantsafety and environment instructions" and "Installation".
To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If your machine is not featured with this program,apply the method described in 6.2.
NOTE
C ¾¾ Use an anti-limescale suitable for the washing machines.
¾¾ Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.
User’s Manual |
11 / EN |
|
|
Preparation
4.5 Correct load capacity
The maximum load capacity depends on the type of laundry,the degree of soiling and the washing programme desired.
The machine automatically adjusts the amount of water according to the weight of the loaded laundry.
DANGER
B |
¾¾ |
Follow the information in the “Programme and consumption table”. When overloaded, machine's |
||||
|
washing performance will drop. Moreover, noise and vibration problems may occur. For a good drying |
|||||
|
|
performance, do not dry laundry more than the amounts specified. |
|
|
||
|
|
|
|
|
||
Laundry type |
Weight (g) |
Laundry type |
Weight (g) |
|
||
Bathrobe |
|
|
1200 |
Hand towel |
100 |
|
|
|
|
|
|
|
|
Napkin |
|
|
100 |
Evening gown |
200 |
|
|
|
|
|
|
|
|
Duvet cover |
|
700 |
Underclothing |
100 |
|
|
|
|
|
|
|
|
|
Bed Sheet |
|
|
500 |
Men’s overalls |
600 |
|
|
|
|
|
|
|
|
Pillowcase |
|
|
200 |
Men’s shirt |
200 |
|
|
|
|
|
|
|
|
Tablecloth |
|
|
250 |
Men’s pajamas |
500 |
|
|
|
|
|
|
|
|
Towel |
|
|
200 |
Blouses |
100 |
|
|
|
|
|
|
|
|
4.6 Loading the laundry
1 Open the loading door.
2 Place laundry items loosely into the machine.
3 Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.
NOTE
C ¾¾ The loading door is locked while a programme is running. The door can only be opened a while after the programme comes to an end. The loading door will not open until the temperature drops if the inside of the machine is very hot at the end of the programme.
A |
CAUTION |
¾¾ In case of misplacing the laundry, noise and vibration problems may occur in the machine. |
4.7 Using detergent and softener
NOTE
C ¾¾ When using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.
4.7.1 Detergent drawer
The detergent drawer is composed of three compartments:
2 
3 1
–(1) for prewash
–(2) for main wash
–(3) for softener
–(*) in addition,there is siphon piece in the softener compartment.
12 / EN |
Washer-Dryer |
|
|
Loading...