Beko WCV8612X0ST User manual [EN]

Washing Machine

User’s Manual

EN

Document Number=

WCV8612X0ST

2302061405_EN/ 14-05

-19.(15:46)

1 General safety instructions

This section includes security
instructions which may help prevent
the injuries and material damage risks.
All kinds of warranties shall be invalid if
these instructions are not observed.

1.1 Lfe and property safety

CAUTION!

A

• Never place the product on a
carpet-covered floor. Electrical
parts will get overheated since
air cannot circulate from under
the device. This will cause
problems with your product.
Unplug the product if it is not in

•
use.
Always have the installation and

•
repairing procedures carried
out by the Authorised Service
Agent. The manufacturer shall
not be held liable for damages
that may arise from procedures
carried out by unauthorised
persons.
The water supply and

•
draining hoses must be
securely fastened and remain
undamaged. Otherwise, water
leak may occur.

1.2 Hot surface safety

• While there is still water inside
the product, never open the
loading door or remove the filter.
Otherwise, risk of flooding and
injury from hot water will occur.
Do not force open the locked

•
loading door. Door can be
opened a few minutes after the
washing cycle ends. In case
of forcing the loading door to
open, the door and the lock
mechanism may get damaged.
Use detergents, softeners

•
and supplements suitable for
automatic washing machines
only.
Follow the instructions on

•
the label of textiles and the
detergent package.

A

• While washing the laundry
at high temperatures, the
loading door glass will get hot.
Considering this fact, during
washing operation keep the
children away from the loading
door of the product to prevent
them touching it.

CAUTION!

This product was manufactured using the latest technology in environmentally friendly conditions.

1.3 Chldren’s safety

A

• This product can be used by

• Packaging materials may be

•

CAUTION!

the children who are at the
age of 8 and over and the
people whose physical, sensory
or mental skills are not fully
developed or who do not have
necessary required experience
and knowledge as long as they
are supervised or trained about
the safe use of the product and
its risks. Children should not
play with the device. Cleaning
and maintenance works should
not be performed by children
unless they are supervised by
someone. Children of less than
3 years should be kept away
unless continuously supervised.

CAUTION!

A

dangerous for the children.
Keep packaging materials in a
safe place away from reach of
the children.
Electrical products are
dangerous for the children.
Keep the children away from
the product when it is in use.
Do not allow them to play
with the product. Use child
lock to prevent children from
intervening with the product.

CAUTION!

A

• Do not forget to close the
loading door when leaving the
room where the product is
located.
Store all detergents and

•
additives in a safe place away
from the reach of the children
by closing the cover of the
detergent container or sealing
the detergent package.

1.4 Electrcal safety

B

• If the product has a failure, it

•

DANGER!

should not be operated unless
it is repaired by the Authorised
Service Agent. Risk of electric
shock!
This product is designed to
resume operating in the event
of powering on after a power
interruption. If you wish to
cancel the programme, see
“Cancelling the programme”
section.

3 / EN

Washing Machine / User’s Manual

B

DANGER!

• Plug the product into a
grounded outlet protected by
a 16 A fuse. Do not neglect to
have the grounding installation
made by a qualified electrician.
Our company shall not be
liable for any damages that
will arise when the product
is used without grounding
in accordance with the local
regulations.

B

DANGER!

• Do not wash the product by
spraying or pouring water onto
it! Risk of electric shock!
Never touch the power cable

•
plug with wet hands! Do not
grab the power cord to unplug
the machine, always unplug it
by holding the socket with one
hand, and pulling the plug with
the other hand.
Product should be unplugged

•
during installation, maintenance,
cleaning and repair procedures.

B

DANGER!

• If the power cable is damaged,
it must be replaced by the
manufacturer, after sales service
or a similarly qualified person
(preferably an electrician) or
someone designated by the
importer in order to avoid
possible risks.

2. Important instructions for
environment

2.1 Compliance with WEEE Directive

This product complies with EU
WEEE Directive (2012/19/EU).
This product bears a classification
symbol for waste electrical and
electronic equipment (WEEE).

This product has been manufactured with
high quality parts and materials which can
be reused and are suitable for recycling. Do
not dispose of the waste product with normal
domestic and other wastes at the end of its
service life. Take it to the collection center
for the recycling of electrical and electronic
equipment. Please consult your local
authorities to learn about these collection
centers.

Compliance with RoHS Directive:
The product you have purchased complies

with EU RoHS Directive (2011/65/EU). It
does not contain harmful and prohibited
materials specified in the Directive.

2.2 Package information

Packaging materials of the product are
manufactured from recyclable materials in
accordance with our National Environment
Regulations. Do not dispose of the
packaging materials together with the
domestic or other wastes. Take them to
the packaging material collection points
designated by the local authorities.

3.Intended use

• This product has been designed for domestic

use. It is not for commercial purposes or it
should not be used out of its intended use.

• The product must only be used

for washing and rinsing of laundry
that are marked accordingly.

• The manufacturer waives any responsibility

arisen from incorrect usage or transportation.

• The service life of your product is 10 years.

During this period, original spare parts will be
available to operate the appliance properly.

4 / EN

Washing Machine / User’s Manual

4 Technical specifications

Complying Commission Delegated Regulation (EU) No 1061/2010

Supplier name or trademark Beko

Model name

Rated capacity (kg)

Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency) A+++

Annual Energy Consumption (kWh)

(1)

Energy consumption of the standard 60°C cotton programme at full load (kWh)

Energy consumption of the standard 60°C cotton programme at partial load (kWh)

Energy consumption of the standard 40°C cotton programme at partial load (kWh)

Power consumption in ‘off-mode’ (W) 0.250

Power consumption in ‘left-on mode’ (W) 1.000

Annual Water Consumption (l)

(2)

Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency)

Maximum spin speed (rpm)

Remaining moisture Content (%)

Standard cotton programme

(3)

Programme time of the standard 60°C cotton programme at full load (min)

Programme time of the standard 60°C cotton programme at partial load (min)

Programme time of the standard 40°C cotton programme at partial load (min)

Duration of the left-on mode (min) N/A

Airborne acoustical noise emissions washing/spinning (dB) 64/80

Built-in No

Height (cm) 84

Width (cm) 60

Depth (cm)

Net weight (±4 kg.)

Single Water inlet / Double Water inlet

• Available

Electrical input (V/Hz) 220-240 V~/ 50Hz

Total current (A) 10

Total power (W) 2000-2350

Main model code

(1)

Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption

of the low-power modes. Actual energy consumption will depend on how the appliance is used.

(2)

Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water

consumption will depend on how the appliance is used.

(3)

“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information
in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient
programmes in terms of combined energy and water consumption.

Technical specifications may be changed without prior notice to improve the quality of the product.

WCV8612X0ST

8

195

1.020

0.744

0.744

10559

B

1200

53

Cotton Eco 60°C and 40°C

245

215

215

55

65

• / -

9210

5 / EN

Washing Machine / User’s Manual

4.1 Installation

• Apply to the nearest authorised service
agent for the installation of your product.

• Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer's
responsibility.

• Make sure that the water inlet and discharge
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.

• Make sure that the installation and electrical
connections of the product are performed
by authorised service. Manufacturer shall
not be held liable for damages that may
arise from procedures carried out by
unauthorised persons.

• Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products cause
risks for your safety.

4.1.1 Appropriate installation location

• Place the product on a hard and level floor.
Do not put it onto a carpet with high pile or
other similar surfaces.

• When the washing machine and dryer are
placed on top of each other, their total
weight –when loaded– amounts to 180 kg.
Place the product on a solid and flat floor
that has sufficient load carrying capacity!

• Do not place the product on the power cable.

• Do not install the product in the
environments where the temperature falls
below 0 ºC.

• Leaving a gap at the sides of the machine is
suggested to reduce vibration and noise

• On a graduated floor, do not place the
product next to the edge or on a platform.

• Do not place heat sources such as Hobs,
Irons, Ovens, etc. on the washing machine
and do not use them on the product.

4.1.2 Removing packaging reinforcement

Tilt the machine
backwards to remove the
packaging reinforcement.
Remove the packaging
reinforcement by pulling
the ribbon. Do not make
this operation alone by
yourself.

4.1.3 Removing the
transportation locks

1 Loosen all bolts with an appropriate wrench

until they turn freely.

2 Remove the transport safety bolts by

turning them slightly.

3 Insert the plastic covers in the bag

containing the user manual to the openings
on the rear panel.

A

• Remove the transportation safety bolts
before operating the washing machine!
Otherwise, the product will be damaged.

C

• Keep the transportation safety
bolts in a safe place to reuse when
the washing machine needs to
be moved again in the future.

• Install the transport safety bolts in reverse
order of the disassembly procedure.

• Never move the product without
the transportation safety bolts
properly fixed in place!

CAUTION!

INFORMATION

4.1.4 Connecting water supply

C

• The water supply pressure required to
run the product is between 1 to 10 bars
(0.1 – 1 MPa). It is necessary to have
10 – 80 liters of water flowing from the
fully open tap in one minute to have your
machine run smoothly. Attach a pressure
reducing valve if water pressure is higher.

A

• Models with a single water inlet should
not be connected to the hot water
tap. In such a case the laundry will get
damaged or the product will switch to
protection mode and will not operate.

• Do not use old or used water inlet
hoses on the new product. It may
cause stains on your laundry.

INFORMATION

CAUTION!

6 / EN

Washing Machine / User’s Manual

1 Tighten the nuts of the hose by hand.

Never use a tool when tightening the nuts.

2 When hose connection is completed,

check whether there is leak problems at the
connection points by opening the taps fully. If
any leaks occur, turn off the tap remove the
nut. Retighten the nut carefully after checking
the seal. In order to prevent the water leaks
and resultant damages, keep the taps closed
when you do not use the product.

4.1.5 Connecting the drain
hose to the drain

• Attach the end of the drain hose directly to
waste water drain, lavatory or bathtub.

A

• Your drain house will be flooded if the
hose comes out of its housing during
water discharge. Moreover, there is risk of
scalding due to high washing temperatures!
In order to prevent such situations and
make sure that the machine performs water
intake and discharge processes without
any problem, fix the drain hose securely.

CAUTION!

• In case the drain hose is elevated after laying
it on the floor level or close to the ground
(less than 40 cm above the ground), water
discharge becomes more difficult and the
laundry may come out excessively wet.
Therefore, follow the heights described in
the figure.

• To prevent the waste water to go back
into the machine again and to ensure easy
drainage, do not immerse the end of the
hose into the waste water or do not insert
it into the drain for more than 15 cm. If it is
too long, cut it short.

• The end of the hose should not be bent,
it should not be stepped on and the hose
must not be pinched between the drain and
the machine.

• If the length of the hose is too short, use
it by adding an original extension hose.
Length of the hose may not be longer than

3.2 m. To avoid water leak failures, the
connection between the extension hose and
the drain hose of the product must be fitted
well with an appropriate clamp as not to
come off and leak.

4.1.6 Adjusting the feet

A

• In order to ensure that the product
operates more silently and vibration­fr
on its feet. Balance the machine by
adjusting the feet. Otherwise, the product
may move from its place and cause
crushing and vibration problems.

• Do not use any tools to loosen the lock
nuts. Otherwise, they will get damaged.

CAUTION!

ee, it must stand level and balanced

100 cm

40 cm

• Connect the drain hose to a minimum height
of 40 cm and a maximum height of 100 cm.

7 / EN

1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a

stable and balanced way.

3. Tighten all lock nuts by hand again.

Washing Machine / User’s Manual

4.1.7 Electrical connection

Connect the product to a grounded outlet
protected by a 16 A fuse. Our company shall
not be liable for any damages that will arise
when the product is used without grounding in
accordance with the local regulations.

• Connection must comply with national regulations.

• The wiring for the electrical outlet circuit
must be sufficient to meet the appliance
requirements. Use of a Groud Fault Circuit
Interrupter (GFCI) is recommended.

• Power cable plug must be within easy reach
after installation.

• If the current value of the fuse or breaker
in the house is less than 16 Amps, have a
qualified electrician install a 16 Amp fuse.

• The voltage specified in the "Technical
specifications" section must be equal to
your mains voltage.

• Do not make connections via extension
cables or multi-plugs.

A

• Damaged power cables must be replaced
by the Authorised Service Agents.

CAUTION!

4.1.8 Initial use

Before starting to
use the product
make sure that
the preparations
are made which
are in line with the
“Important Safety

and Environment Instructions” and the
instructions in the “Installation” section.

To prepare the product for washing laundry,
perform first operation in Drum Cleaning
programme. If this program is not available
in your machine, apply the method which is
described in the section 4.4.2.

C

• Use an anti-limescale suitable
for the washing machines.

• Some water might have remained
in the product due to the quality
control processes in the production.
It is not harmful for the product.

INFORMATION

4.2 Preparation

4.2.1 Sorting the laundry

* Sort laundry according to type of fabric,

color, and degree of soiling and allowable
water temperature.

* Always obey the instructions given on the

garment tags.

4.2.2 Preparing laundry for washing

• Laundry items with metal attachments such
as, underwired bras, belt buckles or metal
buttons will damage the machine. Remove
the metal pieces or wash the clothes by
putting them in a laundry bag or pillow case.

• Take out all substances in the pockets such as
coins, pens and paper clips, and turn pockets
inside out and brush. Such objects may
damage the product or cause noise problem.

• Put small size clothes such as infant's socks
and nylon stockings in a laundry bag or
pillow case.

• Place curtains in without compressing them.
Remove curtain attachment items.

• Fasten zippers, sew loose buttons and
mend rips and tears.

• Wash “machine washable” or “hand
washable” labeled products only with an
appropriate programme.

• Do not wash colours and whites together.
New, dark coloured cottons release a lot of
dye. Wash them separately.

•

Tough stains must be treated properly before
washing. If unsure, check with a dry cleaner.

• Only use the dyes / color changers and
descaling agents which are appropriate
to machine wash. Always follow the
instructions on the package.

• Wash trousers and delicate laundry turned
inside out.

• Keep laundry items made of Angora wool in
the freezer for a few hours before washing.
This will reduce pilling.

•

Laundry that are subjected to materials such
as flour, lime dust, milk powder, etc. intensely
must be shaken off before placing into the
machine. Such dusts and powders on the
laundry may build up on the inner parts of
the machine in time and can cause damage.

4.2.3 Things to be done

for energy saving

Following information will help you use the product
in an ecological and energy-efficient manner.

8 / EN

Washing Machine / User’s Manual