Axis 23XD Installation Guide

Outdoor Housing Installation Instructions

Outdoor power supply connection box

1

Outdoor wall mount Outdoor corner mount

Outdoor hard ceiling mount Outdoor pole mount

See the Axis Web site at http://www.axis.com for more information about the available
outdoor housing and mounting accessories.

2

Outdoor Housing Installation Instructions

Outdoor power supply connection box:

ON/OFF switch

Terminal connectors
(Pins 23-44)

The outdoor power supply contains two sets of terminal connectors to provide easy wiring for alarm inputs/outputs

AC230V/AC115V

voltage selector
switch

Terminal connectors
(Pins 1-22)

Cable gland

Outer ring

Important!

Warning - high voltage. Read through the instructions before starting the installation. The electrical con­nection should be made by an authorized electrician. Please observe relevant national and local regulations
for the installation.

1. Remove the lid of the power supply by removing the 4 screws.

2. Make sure the power switch is set to OFF.

3. Make sure the voltage selector switch is in the correct position. The setting must
correspond to the input main voltage i.e.:

• set the switch to 115V if you intend to power the unit from a 100-120V main

voltage line.

• set the switch to 230V if you intend to power the unit from a 220-240V mains

voltage line.

4. Remove the outer ring of the cable gland , thread the mains cable (not supplied)
through the outer ring and then through the cable gland.

Outdoor Housing Installation Instructions

5. Connect the live/ground wires according to the markings on the PCB (AC230V and
FG or AC115V and FG) . Replace and tighten the outer ring to secure the cable.

6. Connect the dome camera to the power supply using the supplied connection cable:

• Disconnect the outer ring of the cable gland , thread the connection cable

through the outer ring and then through the cable gland.

• Remove the terminal block connectors from the power supply box.

• Following the pinout description on the power supply, push

the colored wires into the corresponding pin holes in the con­nectors and fasten the screws. It is recommended that all
wires are connected, even those that are not used in the
installation.

• Replace the connectors and replace and tighten the outer ring

to secure the cable.

7. Connect any alarm inputs (e.g. doorbell, light) and outputs (e.g. alarm devices) as
follows:

3

• Remove the outer ring of the cable gland , thread the cable (not supplied)

through the outer ring and then through the cable gland.

• Disconnect the terminal block connectors from the power supply box.

• Following the pinout description on the power supply, push the wires into the

corresponding pin holes in the connectors and fasten the screws.

• Replace the connectors and replace and tighten the outer ring to secure the

cables.

8. Check that all cables and wires are securely fastened and that the voltage selector
switch is in the correct position.

9. Proceed to “Outdoor housing installation” on page 4.

4

Outdoor Housing Installation Instructions

Outdoor housing installation

Before you begin:

Check that the you have all the
necessary mounts and that the
cables are long enough for the
installation.

See the Axis Web site at
http://www.axis.com for more
information about the available
outdoor housing, mounting
accessories and cables.

1. Thread the 22 pin connector from the outdoor housing power supply box through
the top of the outdoor housing (and mounts) and connect to the 22 pin connector in
the outdoor housing .

Cable with
22 pin connector

Fixing screw position

22 pin connector

2. Connect the cable in the outdoor housing to the 22 pin connector on the dome
camera .

3. Thread a network cable through the top of the outdoor housing (and mounts) and
connect it to the network connector on the dome camera .

4. Remove the protective black shipping cover from the dome camera.

5. Connect the power and check that the power and network LEDS on the dome camera
light up green . The camera will run a self-test during start up, be careful not to

restrict the camera block movements as this may cause damage.

6. Push the dome camera into the outdoor housing and twist clockwise to lock it into
the bracket making sure that the fixing screw on the dome camera is in the
correct position . Tighten the fixing screw to secure the dome camera.

Fixing screw

22 pin connector

Network connector
and LEDs

Outdoor Housing Installation Instructions

7. Connect the safety wire in the outdoor
housing to the loop in the cover set.

8. Align the screw hole in the housing to the
screw hole in the cover set. Push the rim of
the cover set into the outdoor housing and
fasten securely with the screw.

5

9. Replace the lid of the power supply and
secure with the 4 screws.

Cover set

10.The hardware installation is now complete.

11. Refer to the user documentation provided with the dome camera for information on
the available IP setting methods.

A

6

Technical Specifications

Outdoor Housing Installation Instructions

Connections
Dome housing

Connections
Power Supply

Operating Conditions • Temp: -20 – +50 ºC (-4 – +122 ºF)

Dimensions and Weight • Height: 350 mm (13.8”)

Approvals
(Housing, camera and power
supply)

• 22-pol multi cable to power supply

• Network: 10BaseT/100BaseTX Ethernet networks (RJ-45)

• Power: 115V +/- 10% or 230V +/- 10%, 50/60 Hz, 60VA

• I/O: 4 alarm inputs + 4 outputs (terminal block)

• Humidity: 20 - 80% RHG

• IP rating: IP66

• Diameter: 260 mm (10.2”)

• Weight: 3.3 kg (7.3 lb) (excl. PSU and mounting brackets)

• EMC: CE Compliant according to:
EN55024:1998 +A1
EN55022:1998 +A1 Class A
EN61000-6-1:2001
EN61000-6-2:2001
EN61000-3-2:2000
EN61000-3-3:1995 +A1
FCC Part 15 subpart B Class A, demonstrated by compliance with EN55022:1998
VCCI:2002 Class A ITE
C-tick AS/NZS 3548 Class A

• Safety: EN60950
Power supply - UL/CUL/TUV

Part No. 23408