AVer FD1020 quick guide

AVer FD1020

Quick User Guide

Table of Contents

I. Camera Introduction .................................................................................................... 1

1. Package Contents ............................................................................................... 1

2. Hardware Installation ........................................................................................... 2

2.1 Factory Default .................................................................................................... 7

3. SD card Compatibility List.................................................................................... 8

II. Monitor Setting ............................................................................................................. 9

III. IP Assignment ............................................................................................................ 10

Finding IP Camera by using “NXU Lite recording software” .......................................... 10

Finding IP Camera by using “AVer IPCam Utility” ......................................................... 13

Using NON-DHCP Server/Router Network ................................................................... 15

IV. Connecting the IP Camera ......................................................................................... 17

FCC NOTICE (Class A) ..................................................................................................... 18

COPYRIGHT ...................................................................................................................... 18

NOTICE .............................................................................................................................. 18

WARNING .......................................................................................................................... 18

Limited Warranty .............................................................................................................. 19

Limitations of Warranty .................................................................................................... 19

Disclaimer of Warranty..................................................................................................... 19

Limitation of Liability ....................................................................................................... 20

Governing Law and Your Rights ..................................................................................... 20

Item

Descriptions

1. FD1020

2. Power Adapter (optional item)

3. Wall plus

4. Screw

5. CD (User’s Manual and Quick Guide, NVR
software included)

Before Installation

Before installation, please be sure to read this quick installation guide and user’s manual carefully to

complete the installation.

I. Camera Introduction

The following section introduces package contents, hardware installation, factory default reset, and SD
card Compatibility List of each type camera.

1. Package Contents

**If any of the above items are missing, please contact your dealer immediately.

1

2. Hardware Installation

1. Installation
a. Open the camera cover by pressing the two sides as shown in the following figures:

2

b. Use screws to secure the camera on the ceiling or the wall.

[Note] Do not lock it completely because you might need to adjust the lens angle
later.

c. Unscrew the lens to adjust the angle.

d. After adjusting the lens,screw it tight. Repeat steps b and c as you need during the

whole process.

3

e. Connect the Ethernet and Power adaptor.

f. Break the cover hole carefully and plug-in the Ethernet and power adaptor.

g. After finishing step b and c, screw tight the camera on the ceiling or wall.

h. Close the camera cover.

4

2. Connector Instruction

3. I/O Configuration

a. Connect the G (GND) & DO pin to the external relay (buzzer) device.
b. Connect the G (GND) & DI pin to the external trigger device.

5

When no event occurs, the DO output is 5V (DO and GND are disconnected). When the camera
detects events it will trigger and external alarm, DO output is 0V (DO and GND are connected).

If you select N.O on Input sensor setting, when the switch contacts are opened, the camera input
alarm will be triggered and will execute the action user has set, for example, send a snapshot to

E-mail address.

If you select N.C in Input sensor setting, when the switch contacts are closed, the camera input
alarm will be triggered and will execute the action user has set, for example, send a snapshot to

E-mail address.

I/O PIN definition

c.

 GND (Ground): Initial state is LOW
 DO (Digital Output): DC 5V
 DI (Digital Input): Max. 50mA, DC 5V

6

2.1 Factory Default

1. To recover the default IP address and password, please follow the following steps.

2. Remove power and Ethernet cable.

3. Press and hold the button and connect power and Ethernet cable to the camera again and hold for

round 30 seconds for system booting.

4. Release the button when camera finishes proceed.

5. Re-login the camera using the default IP (http://192.168.1.168) or DHCP, and user name (admin),

password (admin).

7

MicroSD/SDHC card

Transcend SDHC class4 16GB

Transcend SDHC class4 32GB

Transcend SD class4 16GB

Transcend SD class4 32GB

Transcend SD class6 4GB

Transcend SD class6 8GB

Transcend SD class6 16GB

Transcend SDHC class6 4GB

Transcend SDHC class6 8GB

Transcend SDHC class6 16GB

Transcend SDHC class10 4GB

Transcend SDHC class10 8GB

Transcend SDHC class10 16GB

Transcend SDHC class10 64GB

SanDisk SDHC class4 4GB

SanDisk SDHC class4 8GB

SanDisk SDHC class4 16GB

SanDisk SDHC class4 32GB

SanDisk SDHC class4 64GB

3. SD card Compatibility List

FD1020 are compliant with microSD/SDHC card and to ensure recording quality, and please use
memory cards over 2G and Class 4 above (Max. 64GB)

8

II. Monitor Setting

1. Right-click on the desktop. Select “ Properties”

2. Change “Color quality” to “Highest (32-bit)”.

9

Click it to call out virtual
keyboard.

III. IP Assignment

There are two ways to find IP Camera:

 Finding IP Camera by using “NXU Lite recording software”
 Finding IP Camera by using “AVer IPCam Utility”

Finding IP Camera by using “NXU Lite recording software”

1. The NXU Lite software is in the attached software CD. Before launching it, please install the
software first. During the installing process, users will be required to input a User name and
Password for login NXU Lite system. Users can define the User name and Password as wishes.
Please refer to NXU Lite user manual for detailed installation instruction.

2. To run the application, double-click on your PC desktop or click Start > Programs > DVR >
NXU Lite. For security purpose, some of the features would require you to enter User name and
Password before it can be accessed. When the Authorization dialog box appears, key in your User
ID and Password. (If this is the first time, enter the one you have registered when installing the
software.

10

3. Click “Setup” button > Camera.

4. Click “Add IPCam” button.

5. Select “IP Camera” item.

11

Double-click the IP camera model
that user has purchased (ex:
FD1020).

Please ignore ONVIF
protocol selection; NXU Lite
doesn’t support ONVIF
connection.

6. Enter the IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find
camera.

7. In Search Result window, click it the IP camera model that user has purchased (Please ignore
ONVIF connection item); the camera is in red text that is configurable. User can double-click on
the camera is in red text and configure the IP camera’s setting; even the IP camera is not in the
same IP segment. Press “OK” to back to previous screen and press”Connect” to start live view.

12

Finding IP Camera by using “AVer IPCam Utility”

1. Use the software, “AVer IPCam Utility” to assign the IP address of the IP camera. The software is
in the attached software CD.

2. Run the IPCam Utility

3. Select the proper network adapter and click [Search] to begin searching.

4. Select and double click the IP camera you want to access. If you want to change the setting of the
selected IP camera, enter the user ID, correct password, and change the settings and then click
[Apply]. This will change the setting and rescan the network again.

13

5. The IE browser will open and direct you to IP camera login page. This requires IPViewer.ocx to run.
If the IE ActiveX warning message appears, click to allow running the add-on.

[Note]

 The default IP address is: 192.168.1.168
 The default ID and Password are both ”admin”.
 It is not allowed to enter device name in Chinese and any other special characters (' " \ & ^).
 Gateway number can’t be “0”.
 IP camera device name should be less than 30 digits

14

Using NON-DHCP Server/Router Network

In Non-DHCP server/router network, the static IP address must be assigned to the device each time
when adding another IP camera to the network; the default IP address of the current one must be
changed to avoid conflict.

Please make sure the Subnet of the PC’s IP address and the IP camera’s IP address are the same.

[Example]

The same Subnet:

IP camera IP address: 192.168.1.168
PC IP address: 192.168.1.100

Different Subnets:

IP camera IP address: 192.168.1.168
PC IP address: 192.168.2.100

To Change PC IP Address:

Control PanelNetwork ConnectionsLocal Area Connection PropertiesInternet Protocol
(TCP/IP) Properties
Please make sure your IP camera and PC have the same Subnet. If not, please change IP
camera subnet or PC IP subnet accordingly.

PC’s IP address:

15

IP camera IP addresses:

A quick way to access remote monitoring is to double-click on a selected IP camera in “Camera Name
list” in AVer IPCam Utility. Then, the IE browser will open and connect to IP camera.

Then, please key in the default “ID” and “Password”, both of which are “admin”.

16

IV. Connecting the IP Camera

Launch the Internet Explorer browser, type the IP address of the IP camera in the address field. It will
show the following dialogue box. Key-in the ”ID” and “Password”. The default ”ID” and “Password”
are both “admin”.

Once connected to the IP camera, the following program interface will appear.

17

FCC NOTICE (Class A)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device

operation.

Federal Communications Commission Statement
NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

Class A ITE

Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE
limits. Such equipment should not be restricted in its sale but the following warning shall be included in
the instructions for use:
Warning -This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

European Community Compliance Statement (Class A)

Warning - This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures to correct this
interference.

COPYRIGHT

© 2014 AVer Information Inc. All rights reserved.
All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form or by any
means without the prior written permission of AVer Information Inc. is prohibited. All information or
specifications are subject to change without prior notice.

TRADEMARKS

“AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for description

purpose only belong to each of their companies.

NOTICE

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE
INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.

WARNING

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT
MODIFICATION.

must accept any interference received, including interference that may cause undesired

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/television technician for help.

This product is herewith confirmed to comply with the requirements set out in the Council
Directives on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility Directive 2004/108/EC.

18

THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD
WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE WASTE EQUIPMENT BY
HANDING IT OVER TO A DESIGNATED COLLECTION POINT FOR THE
RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR
MORE INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE
EQUIPMENT FOR RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE
PRODUCT.

Limited Warranty

AVer Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms

to AVer’s documentation for the product and that its manufacture and components are free of defects

in material and workmanship under normal use. “You” as used in this agreement means you

individually or the business entity on whose behalf you use or install the product, as applicable. This
limited warranty extends only to You as the original purchaser. Except for the foregoing, the Product is

provided “AS IS.” In no event does AVer warrant that You will be able to operate the Product without

problems or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy

and the entire liability of AVer under this paragraph shall be, at AVer’s option, the repair or replacement

of the Product with the same or a comparable product. This warranty does not apply to (a) any Product
on which the serial number has been defaced, modified, or removed, or (b) cartons, cases, batteries,
cabinets, tapes, or accessories used with this product. This warranty does not apply to any Product
that has suffered damage, deterioration or malfunction due to (a) accident, abuse, misuse, neglect, fire,
water, lightning, or other acts of nature, commercial or industrial use, unauthorized product
modification or failure to follow instructions included with the Product, (b) misapplication of service by
someone other than the manufacturer’s representative, (c) any shipment damages (such claims must
be made with the carrier), or (d) any other causes that do not relate to a Product defect. The Warranty
Period of any repaired or replaced Product shall be the longer of (a) the original Warranty Period or (b)
thirty (30) days from the date of delivery of the repaired or replaced product.

Limitations of Warranty

AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements,
expenses, and attorneys’ fees with respect to claims made against You as a result of Your use or
misuse of the Product. This warranty applies only if the Product is installed, operated, maintained, and
used in accordance with AVer specifications. Specifically, the warranties do not extend to any failure
caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or misuse, (ii)
fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any accessories
or options not furnished by AVer or its authorized agents, or (iv) installation, alteration, or repair of the
Product by anyone other than AVer or its authorized agents.

Disclaimer of Warranty

Except as expressly provided otherwise herein and to the maximum extent permitted by applicable law,
aver disclaims all other warranties with respect to the product, whether express, implied, statutory or
otherwise, including without limitation, satisfactory quality, course of dealing, trade usage or practice or
the implied warranties of merchantability, fitness for a particular purpose or noninfringement of third
party rights.

19

Limitation of Liability

In no event shall aver be liable for indirect, incidental, special, exemplary, punitive, or consequential
damages of any nature including, but not limited to, loss of profits, data, revenue, production, or use,
business interruption, or procurement of substitute goods or services arising out of or in connection
with this limited warranty, or the use or performance of any product, whether based on contract or tort,
including negligence, or any other legal theory, even if aver has advised of the possibility of such
damages. Aver’s total, aggregate liability for damages of any nature, regardless of form of action,
shall in no event exceed the amount paid by you to aver for the specific product upon which liability is
based.

Governing Law and Your Rights

This warranty gives you specific legal rights; You may also have other rights granted under state law.

These rights vary from state to state.

20