Federal Communications Commission Statement(Class A)
NOTE- This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by tuning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
This equipment generates uses and can radiate radio frequency energy and, if not
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/television technician for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B
ITE limits. Such equipment should not be restricted in its sale but the following warning shall be
included in the instructions for use:
Warning - This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
CE Class A (EMC)
This product is herewith confirmed to comply with the requirements set out in the
Council Directives on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility Directive 2004/108/EC.
cause radio interference in which case the user may be required to take adequate measures to
correct this interference.
Warning - This is a Class A product. In a domestic environment this product may
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents
of this documentation, its quality, performance, merchantability, or fitness for a particular
purpose. Information presented in this documentation has been carefully checked for reliability;
however, no responsibility is assumed for inaccuracies. The information contained in this
documentation is subject to change without notice.
In no event will AVer be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use or inability to use this product or documentation, even if advised of the
possibility of such damages.
TRADEMARKS
“AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for
description purpose only belong to each of their companies.
or by any means without the prior written permission of AVer Information Inc. is prohibited. All
information or specifications are subject to change without prior notice.
Page 3
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD
WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE WASTE EQUIPMENT BY
HANDING IT OVER TO A DESIGNATED COLLECTION POINT FOR THE
RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR
MORE INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE
EQUIPMENT FOR RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE
PRODUCT.
NOTICE
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE
INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.
WARNING
TO REDUCE RISK OF FIRE OR ELECTRI C SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. WARRANTY VOID FOR ANY
UNAUTHORIZED PRODUCT MODIFICATION.
Remote Control Battery Safety Information
- Store batteries in any cool & dry place.
- Do not dispose used batteries in domestic waste. Dispose batteries at special
collection points or return to stores if applies.
- Remove the batteries if they are not in use for long period of time. Battery leakage
and corrosion can damage the remote control, dispose batteries safely.
- Do not mix and use old and new batteries.
- Do not mix and use different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
- Do not dispose batteries in a fire.
- Do not attempt to short circuit the battery terminals.
Connections for HDMI output/input external display device.
(6) Control panel
Easy access to various functions.
(7) IR sensor
Receive remote control commands.
(8) Rear panel
Connections for power, computer, RGB/RCA external display device,
and USB to PC.
(9) Right panel
Connections for the camera head holder, SD card, TV-RGB display
output switch, and antitheft Kensington security lock compatible slot.
(10) Built-in MIC
Record audio when recording video clip. The recorded sound will be
in monophonic.
(fig. 1.1)
2
Page 9
(4)
(1)
(2)
(3)
Name
Function
(1) Camera Holder
Hold the camera head for storage.
(2) SD card slot
Insert the SD card with the label facing up.
(3) TV-RGB switch
TV switch to output display video from RCA (viaCVBS adapter) to
RGB OUT and HDMI OUT.
(4) Antitheft Slot
Attach a Kensington compatible security lock or antitheft device.
(5)
(4)(2)
(1)
(3)
Name
Function
(1) DC12V
Connect the power adapter into this port.
(2) RGB INPUT port
Input the signal from a computer or other sources and pass it through
to the RGB OUT port only. Connect this port to the RGB/VGA output
port of a computer.
(3) RGB OUTPUT port
Connect the AVerVision F17HD+ to any display device with RGB cable.
(4) CVBS port
Connect the supplied CVBS adapter into this port. The RCA jack
outputs the video signal from the camera to a TV or video equipment.
(5) Mini USB port
Connect to a USB port of a computer with a USB cable and use
AVerVision F17HD+ as a USB camera or transfer the captured
images/videos from the memory source to computer.
Right Panel
Rear Panel
(fig. 1.2)
(fig. 1.3)
3
Page 10
(2)
(1)
Name
Function
(1) HDMI Out port**
Output the video signal from the main system on an LCD monitor or
LCD/DLP projector with HDMI interface using HDMI cable.
(2) HDMI In port**
Connect an external HDMI source as an input via this port
(1)
(2)
(3)
(4)
(5)
(6)
(9)
(10)
(8)
(7)
(11)
(12)
(13)
(14)
(15)
Name
Function
(1) POWER
Turn the unit on/standby mode.
(2) Zoom In
Increase the image magnification in camera and picture playback
mode.
(3) CAMERA / PC
Switch the video signal between camera or computer from the RGB
IN port.
(4)
Reduce the brightness of live view.
(5) LAMP
Turn the overhead light on/off.
(6) FREEZE/STOP
- Pause or resume image display in Camera mode.
- Stop audio & video playback in Playback mode.
Left Panel
Control Panel
(fig. 1.4)
4
(fig. 1.5)
Page 11
Name
Function
(7) ▲,▼,◄, & ►
- Select options in OSD menu.
- Use ▲&▼ to increase and decrease the video playback volume.
- Use ◄&► to play the video backward and forward.
- Move the Spotlight frame and Visor screen cover.
(8) MENU
Open and exit the OSD menu.
(9) RECORDING
Start/Stop audio & video recording. Audio and video recording can be
saved on a SD card only. See HUExternal Memory StorageUH.
(10) AF / Enter
- Adjust the focus automatically.
- Make a selection in Playback mode and OSD menu.
- Start/Pause video playback.
(11) CAP/DEL
- Capture picture in Camera mode. In continuous capture mode,
press this button again to stop.
- Delete the selected picture/video in Playback mode.
(12)
Increase the brightness of live view.
(13) PLAYBACK
View & playback captured still images and video files.
(14) Zoom Out
Decrease the image magnification in camera and picture playback
mode.
(15) Power LED
indicator
- Red: Standby
- Green: RGB/HDMI output
- Orange: TV output
5
Page 12
Name
Function
(18)
(14)
(11)
(7)
(8)
(5)
(2)
(1)
(22)
(13)
(4)
(3)
(15)
(12)
(17)
(23)
(20)
(19)
(9)
(6)
(16)
(10)
(21)
(fig. 1.6)
(1) POWER
Turn the unit on/standby.
(2) CAMERA
Camera mode displays the video signal
from the built-in camera.
(3) RECORD
Start/Stop audio & video recording.
Video recording can only be saved
either in a SD memory card.
(4) CAPTURE
Capture still image in Camera mode. In
continuous capture mode, press this
button again to stop.
(5) VISOR
Call the Visor submenu. Visor covers
part of the presentation screen and allow
presenter to reveal the material as
desire.
In the Visor submenu, the following
options are available.
ON/OFF – select to run/cancel the Visor.
Press to move to the next
selection.
Shade – set the opacity level of the
covered area. The shaded area will
completely turns black when it is set to
level 100. Press to move to the
next selection.
OK – press for the setting to take
effect. If you select ON, upper part of
the presentation screen is slightly
exposed. Use the ▲,▼,◄, & ► buttons
to reveal more of the covered area; and
OFF will close the submenu.
To turn off Visor, press again.
(6) ROTATE
Rotate the image by 90° in Camera
mode and Playback mode.
(7) MENU
Open and exit the OSD menu.
.
Remote Control
The remote control requires two (2) “AAA” size batteries (supplied), make sure batteries
are installed properly before use. You can access all the features of AVerVision F17HD+
with the remote.
6
Page 13
Name
Function
(18)
(14)
(11)
(7)
(8)
(5)
(2)
(1)
(22)
(13)
(4)
(3)
(15)
(12)
(17)
(23)
(20)
(19)
(9)
(6)
(16)
(10)
(21)
(fig. 1.6)
(8) ▲,▼,◄, & ►
- From remote control to pan the
image when is above 2X in live mode
or playback captured image mode.
- Select options in OSD menu.
- Use ▲&▼ to increase and decrease
the video playback volume.
- Use ◄&► to play the video
backward and forward.
- Move the Spotlight frame and Visor
screen cover.
(9) AUTO FOCUS
Adjust the focus automatically.
(10) ZOOM +/-
Increase/decrease the image
magnification in camera and picture
playback mode.
(11) ZOOM RESET
Reset zoom level to 100%.
(12) PLAYBACK
View the captured picture/video from
the memory in 16-thumbnail images.
(13) PC 1/2
PC mode displays the video signal
from the RGB/HDMI INPUT port of
F17HD+.
(14) FREEZE /
STOP
- Freeze live images.
- Stop video playback.
(15) SPOTLIGHT
Call the Spotlight submenu. Spotlight
overlays a box frame on the
presentation screen. You can adjust the
box size and move it around.
In the Spotlight submenu, the following
options are available.
ON/OFF – select to run/cancel the
Spotlight. Press to move to the
next selection.
Shade – set the opacity level of the area
outside the box. The shaded area will
completely turns black when it is set to
level 100. Press to move to the
next selection.
7
Page 14
Name
Function
(18)
(14)
(11)
(7)
(8)
(5)
(2)
(1)
(22)
(13)
(4)
(3)
(15)
(12)
(17)
(23)
(20)
(19)
(9)
(6)
(16)
(10)
(21)
(fig. 1.6)
(15) SPOTLIGHT
Color – select the Spotlight frame color.
Press to move to the next
selection.
OK – press for the setting to take
effect. If you select ON, the frame will
appear and blink, use the ▲,▼,◄, & ►
buttons to adjust the frame size and
press to set the desired size; and
OFF will close the submenu.
To turn off Spotlight, press again.
(16) SPLIT
SCREEN
Divide the screen into two. One side
displays the live image from the built-in
camera and the other side displays 8thumbnail size picture/video from the
memory.
(17) MODE
Select from 4 type of modes:
Sharp - adjust the contrast along the
edges making text appear more visible.
Graphics - adjust the gradient of
image.
Motion - increase frame rate. Sufficient
lighting is required when using this
mode.
Microscope - automatically adjust
optical zoom for microscopic viewing.
(18) TIMER
Call the Timer submenu. Select to
Start/Pause/Stop the timer countdown
and set the timer duration.
(19)
- Make a selection in Playback mode
and OSD menu.
- Play/Pause video playback.
(20) LAMP
Turn the overhead light on/off.
(21) BRIGHTNESS
+/-
Adjust the brightness.
(22) DEFAULT
Reset to factory default setting.
(23) DEL
Delete the selected picture/video in
Playback mode.
CCoonnnneecctt ttoo aa MMoonniittoorr oorr LLCCDD//DDLLPP PPrroojjeeccttoorr
Make sure the TV/RGB switch is set to RGB.
Before making the connection, make sure the power of all devices are turned off. If you are
not sure on where to connect, simply follow the illustrated connections below and also refer
to the user manual of the device you are connecting the AVerVision F17HD+ with.
The TV-RGB switch determines the display output selection. Switch it to RGB (right) to
output signal using RGB/HDMI connection and TV (left) to output signal using RCA
connection. (see fig. 1.2 # 3)
Locate the RGB (VGA) input port of the graphics display device and connect it to RGB
OUT port of AVerVision F17HD+.
Locate the HDMI input port of the display device and connect it to HDMI out port of
AVerVision F17HD+.
Locate the VIDEO or SCART RGB (if applicable) input port of the TV or Video equipment
(i.e., VCR) to record your presentation and connect it to RCA jack of CVBS adaptor.
10
Page 17
CCoonnnneeccttiinngg tthhee PPoowweerr
Power adapter
Wall outlet
CCoonnnneecctt ttoo aa CCoommppuutteerr
- To display computer image, press Camera/PC button on the control panel or
remote control to switch AVerVision F17HD+ to computer mode.
- For laptop to output display image, use the keyboard command (FN+F5) to
switch between the display modes. For different command, please refer to
your laptop manual.
Connect the power adapter to a standard 100V~240V AC power outlet. The unit
automatically in standby mode once the power is connected. Press to turn on.
Locate the RGB (VGA) output port of the computer or laptop and connect it to RGB IN port
of DocCam. The video signal from the RGB IN port is streamed to RGB OUT.
11
Page 18
CCoonnnneecctt ttoo aa CCoommppuutteerr vviiaa UUSSB
B
CCoonnnneecctt ttoo aa CCoommppuutteerr wwiitthh HHDDMMII IInnppuutt iinntteerrffaaccee
- Make sure the TV/RGB switch is set to RGB.
- To display computer image, press Camera/PC button on the control panel or
remote control to switch AVerVision F17HD+ to computer mode.
- For laptop to output display image, use the keyboard command (FN+F5) to
switch between the display modes. For different command, please refer to
your laptop manual.
Locate the USB port of the computer or laptop and connect it to PC port of AVerVision
F17HD+.
Locate the HDMI output port of the computer of laptop and connect it to HDMI in port of
AVerVision F17HD+.
This section provides useful tips on how to adjust the AVerVision F17HD+ to meet your
needs.
The gooseneck design allows you to freely bend the arm and store the camera head in the
camera holder. Once you have properly secured the camera head to the camera holder,
you may use the arm to carry AVerVision F17HD+.
14
Page 21
SShhoooottiinngg AArreeaa
5
00
m
m
375
m
m
297
m
m
210
m
m
297
m
m
420
m
m
The shooting area can view an area of 500x375mm which allows you to show an A4 size
portrait paper.
If the camera head is in upright position, press ROTATE on the control panel or remote
control twice to rotate the image in 180°.
To mirror the image, press MENU > select Mirror, press , and select On.
15
Page 22
OOvveerrhheeaadd LLiigghhtt
IInnffrraarreedd SSeennssoorr
Press LAMP button on the control panel or remote control to turn on and off light.
Aim the remote control at the infrared sensor to operate the unit.
16
Page 23
MMoouunnttiinngg tthhee FF1177HHDD++ oonn aa FFllaatt SSuurrffaaccee
75mm
75mm
M4
AAnnttii--ggllaarree SShheeeett
Measure and mark the horizontal of 75 mm from the center line distance between the holes
on the flat surface as describe in the illustration below. Use 2 pieces of M4.0 screws for 6
mm holes and secure the F17HD+ on the flat surface.
The anti-glare sheet is a special coated film that helps eliminate any glare that maybe
encountered while displaying very shiny objects or glossy surfaces such as magazines and
pictures. To use, simply place the anti-glare sheet on top of the shiny document to reduce
reflected light.
17
Page 24
EExxtteerrnnaall MMeemmoorryy SSttoorraaggee
IInnsseerrtt aann SSDD CCaarrdd
AVerVision F17HD+ supports both SD memory card for more image capture and audio &
video recordings. AVerVision F17HD+ can detect when there is an external storage media
and automatically switch to the last detected storage. If no external storage is connected,
all captured still images will be saved in the built-in memory.
Insert the card with the contact facing down until it reaches the end. To remove the card,
push to eject and pull the card out. The supported SD card capacity is from 1GB to 32GB
(FAT32). We recommend using SDHC card with class-6 or above for high quality recording.
18
Page 25
OOSSDD MMEENNUU
For TV output, the RESOLUTION will be disabled in SETTING menu list.
IMAGE
PRESENTATION
SETTING
SYSTEM
PLAYBACK
There are 4 tabs on the OSD menu: IMAGE, PRESENTATION, SETTING and SYSTEM. In
Playback mode, you can access PLAYBACK OSD menu to enable the Slide Show feature
and modify Slide Show interval and transition setting if desire.
Adjust brightness level manually between 0 and 63.
47BContrast
Adjust the contrast level manually between 0 and 255
under bright and dark environments.
20
Page 27
Menu Screen
Function
49BMode
Select from the various image display settings.
Sharp - adjust the contrast along the edges making
text appear more visible.
Graphics - adjust the gradient of image.
Motion - increase frame rate. Sufficient lighting is
required when using this mode.
Microscope - automatically adjust optical zoom for
microscopic viewing.
51BEffect
Convert the image into positive (true color), monochrome
(black and white) or negative.
8BMirror
Select to flip the image in Camera mode.
48BAdvanced
Select to set the Auto Image, Exposure, and White
Balance settings.
48BAuto Image
Select ON or OFF to automatically adjust the white
balance and exposure setting, and correct the color and
exposure compensation.
21
Page 28
Menu Screen
Function
53BExposure
Select the exposure setting.
AUTO - automatically adjust the camera exposure and
the amount of light required.
MANUAL - manually adjust the exposure level. The
exposure can be adjusted up to 100.
54BWhite Balance
Select the White Balance setting for various light
conditions or color temperature.
AUTO - automatically adjust the white balance.
MANUAL - manually adjust the red and blue color level.
The color level can be adjusted up to 255.
50BFocus
Manually adjust the focus.
22
Page 29
PPrreesseennttaattiioonn
Menu Screen
Function
57BSpotlight
Spotlight overlays a frame on the presentation screen.
You can move the Spotlight around the presentation
screen using the ▲,▼,◄, & ► buttons. Select Execute
to call the Spotlight submenu.
In the Spotlight submenu, the following options are available.
ON/OFF – select to run/cancel the Spotlight. Press to
move to the next selection.
Shade – set the opacity level of the area outside the box.
The shaded area will completely turns black when it is set
to level 100. Press to move to the next selection.
Color – select the Spotlight frame color. Press to
move to the next selection.
OK – press for the setting to take effect. If you select
ON, the frame will appear and blink, use the ▲,▼,◄, & ► buttons to adjust the frame size and press to set
the desired size; and OFF will close the submenu.
60BVisor
Visor covers the presentation
screen. The upper part of the
presentation screen is slightly
exposed. Use the ▲,▼,◄, & ►
buttons to reveal more of the
covered area. Select Execute to call
the Visor submenu.
23
Page 30
Menu Screen
Function
In the Visor submenu, the following options are available.
ON/OFF – select to run/cancel the Visor. Press to move to
the next selection.
Shade – set the opacity level of the covered area. The shaded
area will completely turns black when it is set to level 100. Press
to move to the next selection.
OK – press for the setting to take effect. If you select ON,
upper part of the presentation screen is slightly exposed. Use the
▲,▼,◄, & ► buttons to reveal more of the covered area; and
OFF will close the submenu.
62BPIP
Select the thumbnail playback screen location and show
the thumbnail playback screen at the corner of the
screen to recall the captured image from the memory in
Camera mode. Select OFF to cancel PIP.
Lower Left
Upper Left
Upper Right
Lower Right
63BSplit Screen
Divide the screen into two parts. Half of the screen
displays the 8-thumbnail images and the other half
display the image from the AVerVision F17HD+ camera.
Select the display location of the 8- thumbnail playback
images. Select OFF to cancel Split Screen.
Left
Right
Top
Below
24
Page 31
Menu Screen
Function
64BTimer
Start/Pause/Stop the timer and set the timer duration.
The timer automatically counts up after the count down
reaches zero to show the elapsed time. Even when you
switch between Playback, PC or Camera modes, the
timer will continue.
SSeettttiinngg
Menu Screen
Function
48BCapture
Select to set the capture resolution, quality, type and
interval settings.
66BResolution
Select the capture size. In 5M setting, the capture
resolution size is 2560 X 1920.
67BQuality
Select the capture compression setting.
25
Page 32
Menu Screen
Function
68BType
Select the capture type.
Single - capture one picture only.
Continuous - capture successive pictures.
69BInterval
Set the time interval for continuous capture. The length
can be set up to 600 sec (10 min).
72BStorage
Change the storage location. Audio & video recording
can only be saved in SD memory card.
73BFormat
Format to delete all the data in the selected memory.
76BUSB to PC
Select the status of the AVerVision F17HD+ when it is
connected to the computer via USB. Make sure the USB
switch on the left panel is set to .
Camera - can be used as a computer webcam or with
our bundled software to record video and capture still
image.
Storage - transfer the captured pictures/videos from the
memory to computer hard disk.
26
Page 33
Menu Screen
Function
55BFlicker
Select between 50Hz or 60Hz. Some display devices
cannot handle high refresh rates. The image will flicker a
couple of times as the output is switched to another
refresh rate.
SSyysstteemm
Menu Screen
Function
74BLanguage
Change and select different language.
75BOutput Display
Set the resolution to display the image on screen. This
selection will be disabled in TV output mode.
77BBackup
Copy the image from the built-in memory to SD card.
27
Page 34
Menu Screen
Function
78BSave Setting
Save current setting in the selected profile number. Only
effect, mode, brightness and contrast settings can be
saved.
Recall Setting
Restore the setting back to the selected profile number.
80BInformation
Display the product information.
52BDefault
Restore all the settings into original factory default
setting.
28
Page 35
PPllaayybbaacck
k
Menu Screen
Function
81BSlide Show
Display all captured still pictures in an automated slide
show. The video file will be skipped.
Interval
Set the interval before displaying the next picture. The
length can be set up to 100 sec.
83BSlide Show Effect
Select the slide show transition effect.
Slide image
Wipe right
Checker down
Split Vertical Out
Wipe down
Split Horizontal In
84BCurrent Storage
Select the source of the images.
85BDelete All
Permanently delete all the data in selected memory
source. A Warning Message will appear. Select YES to
continue and NO to stop formatting the storage.
29
Page 36
TTrraannssffeerr CCaappttuurreedd IImmaaggeess//VViiddeeooss ttoo aa ccoommppuutteer
r
The instruction below MUST be read and followed BEFORE connecting
the USB cable.
This enables you to transfer the captured image from the built-in memory or SD to a
computer.
1. MUST set the USB to PC as STORAGE before connecting the USB cable.
2. When “Mass Storage Start…” appears at the lower right corner of the presentation
screen, you may now connect the USB cable.
3. Upon connecting the USB cable, the system automatically detects the new removable
disk. You can now transfer the captured image(s) from the F17HD+ built-in memoryU to
the computer hard disk.
30
Page 37
TTeecchhnniiccaall SSppeecciiffiiccaattiioonnss
Sensor
1/4” CMOS
Pixel Count
5 megapixels
Frame Rate
30 fps (max.)
White Balance
Auto / Manual
Exposure
Auto / Manual
Image mode
Sharp / Graphics / Motion / Microscope
Effect
Color / B/W / Negative
RGB output
1920x1080, 1600x1200, 1280x1024, 1280x720, 1024x768,
1280 x 800
HDMI Output
HD 1080p 60Hz; HD 720p 60Hz
Image Capture
240 Frames(XGA) ; 80 Frames(5M Pixel)
Focusing
Auto
Shooting Area
500mm x 375mm
Zooming
Total 32X (2X AVer ZoomTM, 16X Digital zoom)
Power Source
DC 12V, 2A 100-240V
Consumption
12 Watts (lamp off); 12.8 Watts (lamp on)
Lamp Type
LED light
RGB Input
15-Pins D-sub (VGA)
RGB Output
15-Pins D-sub (VGA)
HDMI Output
HDMI
HDMI Input
HDMI
Composite Video
RCA Jack
USB
USB2.0
DC 12V Input
Power Jack
Operating
380(L)*200(W)*525mm(H) (+/-2mm include rubber foot)
Folded
305(L)*230(W)*73mm(H) (+/-2mm include rubber foot)
Weight
2.44 kg (about 5.38lbs)
Secure Digital
(SDHC)
1GB ~ 32GB (FAT32)
Image
Optics
Power
Lighting
Input/Output
Dimension
External Storage
31
Page 38
TTrroouubblleesshhoooottiinngg
This section provides many useful tips on how to solve common problems while using the
AVerVision F17HD+.
There is no picture on the presentation screen.
1. Check all the connectors again as shown in this manual.
2. Check the on/off switch of the display output device.
3. Verify the setting of the display output device.
4. If you are presenting from a notebook or computer through the display output device, check the
cable connection from computer RGB (VGA) output to RGB input of AVerVision F17HD+ and
make sure AVerVision F17HD+ is in PC Mode.
I have set up the AVerVision F17HD+ and checked all the connections as specified in
the manual but I cannot get a picture on the preferred presentation screen.
1. Once the power is connected the unit is set to standby mode. Press the POWER button to turn on.
2. If your display output device is on TV or any analog device, please switch the TV-RGB dip switch
to TV.
The picture on the presentation screen is distorted or the image is blurry.
1. Reset all changed settings, if any, to the original manufacturer default setting. Press MENU then
go to SYSTEM > Default and select YES in the OSD menu.
2. Use the Brightness and Contrast menu functions to reduce the distortion if applicable.
3. If you discover that the image is blurry or out of focus, press the Auto Focus button on the control
panel or remote control.
There is no computer signal on presentation screen.
1. Check all the cable connections among the display device, AVerVision F17HD+ and your PC.
2. Connect your PC to the AVerVision F17HD+ first before you power on your computer.
3. For notebook, repeatedly press FN+F5 to toggles between display modes and display the
computer image on the presentation screen. For different command, please refer to your laptop
manual.
The presentation screen does not show the exact desktop image on my PC or
Notebook after I toggle from Camera to PC mode.
1. Return to your PC or Notebook, place the mouse on the desktop and right click, choose
“Properties”, choose “Setting” tab, click on “2” monitor and check the box “Extend my Windows
desktop onto this monitor”.
2. Then go back one more time to your PC or Notebook and place the mouse on the desktop and
right click again.
3. This time choose “Graphics Options”, then “Output To”, then “Intel® Dual Display Clone”, and then
choose “Monitor + Notebook”.
4. After you follow these steps, you should be able to see the same desktop image on your PC or
Notebook as well as on the presentation screen.
32
Page 39
LLiimmiitteedd WWaarrrraannttyy
For a period of time beginning on the date of purchase of the applicable product and extending as set
forth in the “Warranty Period of AVer Product Purchased” section of the warranty card, AVer
Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to
AVer’s documentation for the product and that its manufacture and components are free of defects in
material and workmanship under normal use. “You” as used in this agreement means you individually
or the business entity on whose behalf you use or install the product, as applicable. This limited
warranty extends only to You as the original purchaser. Except for the foregoing, the Product is
provided “AS IS.” In no event does AVer warrant that You will be able to operate the Product without
problems or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy
and the entire liability of AVer under this paragraph shall be, at AVer’s option, the repair or replacement
of the Product with the same or a comparable product. This warranty does not apply to (a) any Product
on which the serial number has been defaced, modified, or removed, or (b) cartons, cases, batteries,
cabinets, tapes, or accessories used with this product. This warranty does not apply to any Product
that has suffered damage, deterioration or malfunction due to (a) accident, abuse, misuse, neglect, fire,
water, lightning, or other acts of nature, commercial or industrial use, unauthorized product
modification or failure to follow instructions included with the Product, (b) misapplication of service by
someone other than the manufacturer’s representative, (c) any shipment damages (such claims must
be made with the carrier), or (d) any other causes that do not relate to a Product defect. The Warranty
Period of any repaired or replaced Product shall be the longer of (a) the original Warranty Period or (b)
thirty (30) days from the date of delivery of the repaired or replaced product.
Limitations of Warranty
AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements,
expenses, and attorneys’ fees with respect to claims made against You as a result of Your use or
misuse of the Product. This warranty applies only if the Product is installed, operated, maintained, and
used in accordance with AVer specifications. Specifically, the warranties do not extend to any failure
caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or misuse, (ii)
fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any accessories
or options not furnished by AVer or its authorized agents, or (iv) installation, alteration, or repair of the
Product by anyone other than AVer or its authorized agents.
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, AVER DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT
TO THE PRODUCT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING
WITHOUT LIMITATION, SATISFACTORY QUALITY, COURSE OF DEALING, TRADE USAGE OR
PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVER BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT NOT LIMITED
TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE, BUSINESS INTERRUPTION,
OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES ARISING OUT OF OR IN
CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE OF ANY
PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR ANY
OTHER LEGAL THEORY, EVEN IF AVER HAS ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. AVER’S TOTAL, AGGREGATE LIABILITY FOR DAMAGES OF ANY NATURE,
REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT PAID BY
YOU TO AVER FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
33
Page 40
For warranty period, please refer to the warranty card.
Governing Law and Your Rights
This warranty gives you specific legal rights; You may also have other rights granted under state law.
These rights vary from state to state.
34
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.