Auto Page RF-420LCD User Manual

NED FOR PROFESSIONAL INSTALLATION ONLY
RF-420LCD
PROFESSIONAL VEHICLE SECURITY SYSTEM
OPERATION MANUAL
2
Transmitter
he siren sounds 3
chirps, then you have
left a door, trunk, or
Button
-
+
-
-
+ +
II
ACTIVE ARMING – LOCK & ARM:
1. Press button on transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle doors will loc k upon arming when interfaced with the security system.
Note: Defective sensor reminder:
If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. System Arm
System Function Remark
Lock Doors & Arm System Panic function Press and Hold for 3 seconds Car Locator Under armed mode Arm and Delete The 2 Stage Shock
Sensor Silent Arming / Disarming Ignition in "off" position.
Unlock Doors & Disarm System Two Steps Door Unlock & Disarm
System Trunk Release (Channel 2) Press and Hold for 2 seconds
Passive Arming By -pass While the system Disarmed. Silent Arming 3rd Channel Press buttons together 4th Channel Press buttons together
Switching code For 2nd Car Operation.
Door Ajar
Trunk / Hood Ajar
Press twice within 3 seconds
Press twice within 3 seconds.
For regular remote transmitter Only
AJAR WARNING:
If t
hood lid ajar.
TRANSMITTER OPERATION:
SILENT ARMING / DISARMING: Press the button on the transmitter to arm or disarm your
security system with no chirp sound heard; arm / disarm confirmation will be through the vehicles parking lights only.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS:
Press the button on the transmitter twice within 3 seconds will arm the security system, by ­pass the shock sensor or the optional sensor connected to 4 pin plug. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.
3
PASSIVE ARMING:
will
Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING: The vehicle doors will automatically lock after passive arming cycle has been completed.
PASSIVE ARMING BY-PASS: While the system disarmed, press the buttons twice, the security will respond with [1] chirp and LED will turn “ON”. The security system will remain in
this temporarily state for as long as you wish. To exit passive by -pass, press the or button and the system will return to normal status.
ACTIVE DISARMING – UNLOCK & DISARM:
1. Press the button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice to indicate that the security system is now disarmed. The vehicle doors will unlock and disarm when interfaced with the security system.
System Disarm
Trunk/Hood Trigger
Doors Trigger
Shock Sensor Trigger
Ignition Trigger
TAMPER DISARMING: If the alarm is triggered; upon disarming of the system, the siren will
chirp 4 times and parking lights will flash 3 times.
Clear the Flash Icon and Melody Sound: Cycle Ignition then press the button first, within 3 seconds press and buttons at the same time. It
clear the flash icon and melody sound on the LCD screen transceiver
4
PATHWAY ILLUMINATION: This feature turns the parking light “ON” for 30 seconds upon a
From the disarmed condition, turn the
Push and hold valet switch for 2 seconds
lls
remain on as long as the system is in
unlock signal and for 10 seconds upon the lock signal if programmed. TWO STEP DOOR UNLOCK: This feature will independently unlock the driver’s door only when
disarming the security system. Pushing the button on the transmitter a second time within 3 seconds will unlock the entire vehicle. (Additional installation required)
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however, the remote panic feature and remote door locks will remain operational.
Enter Valet Mode:
1. ignition to “ON” position.
2.
until the LED turns on. The LED wi 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'ON'.
2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting the valet mode.
POWER ON MEMORY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.
1. Press and hold the button on the transmitter for 3 seconds. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be suspended. The and buttons can be used to lock and unlock the doors (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be
enable allowing the vehicle to start.
3. To stop the alarm, press and hold the or or button on the transmitter for 3 seconds. Also if the button is pressed and released, the panic mode will be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.
Remote Door Lock
Remote Door Unlock
5
TRIGGER THE SYSTEM
he same
flash icon and melody sound on the LCD screen
It is useful in the event that someone wants to page the driver of the parked vehicle. With the
button on the window mount antenna once to
page the driver, one chirp sound shall be emitted from the vehicle and the paging melody
n the LCD
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away signal. A long chirp from siren/horn.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will
trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and parking lights will turn on to alert of an intrusion for 30 seconds. Then the siren will stop and automatically reset and re-arm. If any of the sensors or detectors are still active, the alarm system will sound a maximum of three-30 second cycles.
Trunk/Hood Trigger
Doors Trigger
Shock Sensor Trigger
Ignition Trigger
Warn-away Trigger
NOISE ABATEMENT CIRCUIT:
Your system has “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers, airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or switch is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm. After the fifth trigger, “Noise Abatement Circuit” ignores, or bypasses, that sensor or switch until the other sensor or switch is trigger. “Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trigger ceases.
DRIVER PAGING (For two-way transmitter operation only)
ignition switch in the “off” condition, press the
continues sounding from your Remote LCD Transmitter and “ ” indication flashes o screen.
Clear the Flash Icon and Melody Sound: Cycle ignition then press the
button first, within 3 seconds press and buttons at t time. It will clear the transceiver
6
IGNITION CONTROL DOOR LOCKS. If the vehicle’s door locks have been interfaced to the security system, the system will
automatically lock the vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.
TRUNK RELEASE.
Press and hold button on transmitter for two seconds to remote control the trunk release or other electric devices.
CHANNEL 3 CONTROL OUTPUT Press the + buttons on the transmitter to active Channel 3 function
CHANNEL 4 CONTROL OUTPUT Press the + buttons on the transmitter to active Channel 4 function.
CAR LOCATOR Under Armed mode, press the button on the transmitter to active car locator function.
The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car.
DOME LIGHT CONVENIENCE DELAY & SUPERVISION The alarm with a unique feature which will turn on your vehicle dome light as following:
1. Upon disarming, the interior lights will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren. Note: Turn ON the ignition switch or arm the alarm will turn off the dome light.
(Additional installation required)
LCD REMOTE CONTROL TRANSMITTER:
Note: If the system is interfered by stronger radio
frequency around, sources of high voltage electric power or such obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low output powered frequency.
7
BATTERY REPLACEMENT:
icon shall be displayed
replaced to new one, there will be beep sounds
button two times when the
battery compartment is empty, and then insert
All the function shall be temporarily on
Someone is paging you in front of your
AAA
A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the
battery weakens a on the LCD screen. When the old battery is
indicate the power is up.
Note: Press the the new battery. THE REMORE LCD ICONS WITH FUNCTION:
Door Lock
Your vehicle doors are locked
Armed Mode
Your vehicle is in armed mode
Remote Transmission
You are transmitting the signal to control unit Trunk/Hood Trigger Trunk or Hood is illegally opened (Zone 2)
Shock Sensor Trigger
Trigger on Shock Sensor (Zone 4)
Warn Away trigger Trigger on Shock Sensor (Zone 1)
Vibration Mode
Remote Control vibrates when the system is triggered
Power Save Mode Save the battery power
Door Unlock
Your vehicle doors are unlocked and the system is Disarmed
Valet Mode
hold. In – Range Indicator
You are within the remote control range.
Door Open Warning Doors are illegally opened (Zone 3)
Ignition Trigger Trigger on Ignition Switch (Zone 5) Low Battery
You have to replace the battery of remote control.
Driver paging / Lose and Found
vehicle
8
PROGRAM MODE FOR LCD REMOTE CONTROL TRANSCEIVER:
all four remote control buttons simultaneously unit one long
s is
e second
3. To exit programming mode, take no action for five seconds. The remote
control will generate two long beeps to indicate programming mode has
1. Press and hold all four remote control buttons simultaneously unit one long
is heard.
3. To exit programming mode, take no action for five seconds. The remote
control will generate two long beeps to indicate programming mode has been
e control buttons simultaneously unit one long
button to select the mode of vibration or melody,
on the LCD screen to show the LCD remote
3. To exit programming mode, take no action for five seconds. The remote control
Transceiver Button System Function Remark
Program Mode - Program Mode - Program Mode -
- +
- +
1. Second Vehicle Security Operation: Your remote transmitter can be utilized to control a second vehicle Autopage security system. To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming parameters are the same except for the following:
For Regular Remote Control Transmitter:
1. Prior to pushing any button on the transmitter. Press the Select II button first on the standard
transmitter.
2. Once II button is pressed the LED on the transmitter will illuminate for 3.5 seconds. While the
LED is illuminated, press the button for the function you want to operate on the standard remote transmitter to control a second vehicle security system.
For 2-way LCD Remote Control Transceiver:
2nd Car Operation: While the “II” icon display on the LCD screen, you can remote control and communicate with a second Autopage AM frequency security system. It has two short “beep” sounds while pressing the button of the LCD screen transceiver
1. Press and hold
beep is heard. LCD Programming has now been entered.
2. Within 5 seconds press and hold button until two beeping sound
heard and the “II” icon will display on the LCD screen to indicate th transceiver pin code has built-in.
Switching code for 2nd / 1st Car Operation Press within 5 seconds Melody / Vibration Mode Press within 5 seconds Power Save Mode Press within 5 seconds LCD screen lamp turns on for 5 seconds.
System’s Status Check Press within 3 seconds Clear the Flash Icon and Melody Sound Press within 3 seconds
been exited. Back to First Car Operation: You can remote control and communicate with a first vehicle security system. It has one short “beep” sound while pressing the button of the LCD screen transceiver.
beep is heard. Programming has now been entered.
2. Within 5 seconds press and hold button until one beeping sound
exited.
Vibration / Melody Mode:
Vibration mode is useful when you are in a noisy place and it is difficult to hear beep sound from the remote control. In this mode the remote control will vibrate if your security system is triggered.
1. Press and hold all four remot beep is heard. Programming has now been entered.
2. Within 5 seconds, press the the icon will displayed
transceiver is on vibration mode. will generate two long beeps to indicate programming mode has been exited.
9
usly unit one long
. The remote will
3. To exit programming mode, take no action for five seconds. The remote control
When you want to check the system’s present status
, within 3 seconds
with one melody sound, the
Power Save Mode: While in the power save mode, the LCD remote transceiver will “sleep” until a button is pushed,
to extend the life of battery. When power save mode is ON, the remote control will wake up periodically to check for messages from the security module.
1. Press and hold all four remote control buttons simultaneo beep is heard. Programming has now been entered.
2. Within 5 seconds, press the button to toggle “On” or “Off” beep once for “On”, twice for “Off”. When power save mode is “On”, the icon on the LCD screens to indicat e entry the “power save mode”
will generate two long beeps to indicate programming mode has been exited.
Screen Lamp ON:
Press the button once; the LCD screen lamp will turn on for 5 seconds
System’s Status Check
through the LCD screen, Press the transceiver button first press and buttons at the same time. It responds LCD screen should be illuminated.
Note: If it has no response then you are out of range.
Clear the Flash Icon and Melody Sound:
Cycle ignition then press the button first, within 3 seconds press and buttons at the same time. It will clear the flash icon and melody sound on the LCD screen transceiver
Stop The Trigger Melody Sound:
While triggering the alarm the LCD screen will alert the user through melody sound and flashing trigger icon. Press any button on the LCD remote transmitter to stop melody sound.
10
Off or Fast
ALARM OPERATING CONDITION :
Function Siren Parking
1. Arm 1 Chirp 1 Flash Slow flash Locking On
2. Disarm 2or4 Chirps
3. Trigger Alarming Flashing Slow flash On flashes
4. Panic Alarming Flashing Slow flash Locking On flashes
5.Car Locator 6 Chirps 12 Flashes
Lights
2 or 3 Flashes
LED Doors Starter
Unlocking Off On for
flash
Disable
Dome
Light
30 sec
ALARM INDICATORS
CHIRP INDICATORS: PARKING LIGHTS:
Chirp Function Parking Light Function
1 chirp Arm 1 flash Arm 2 chirps Disarm 3 chirps Defective
reminder
4 chirps Disarm/
Intrusion
6 chirps Car Locator
LED INDICATORS:
LED Function
Off Disarmed Slow
Armed
flash Fast
flash On
Passive arming
Valet mode
(solid)
2 flashes... pause
3 flashes... pause
4 flashes... pause
5 flashes... pause
2 flashes Disarm 3 flashes Disarm/
Intrusion
12 flashes Car
Locator
LED Function
Trigger on trunk/hood Trigger on door
switch Trigger on Dual Zone
Shock Sensor Trigger on Ignition
switch
11
LIMITED LIFETIME WARRANTY PROVISIONS
( U.S. ,Continental U.S. and Canada Only)
1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the
factory prior to delivery. Your Auto Page equipment is guaranteed for “life” to the original purchaser/user of the equipment and the original vehicle in which it was installed by an authorized installer under the following conditions: If the product proves defective (according to Auto Page's testing) within the first year, the defective unit may be exchanged or repaired free of charge. “Proof of Purchase” (dated sales receipt) must accompany all warranty returns; otherwise, your return will be rejected and sent back. After one (1) year, the purchaser should ship the unit prepaid to Auto Page with a money order in the amount of $30.00 to cover shipping and handling charges. Note: The enclosed Warranty Card may be required to receive warranty services.
2. This WARRANTY will be considered void if the equipment has been misused, neglected,
improperly serviced or installed, altered, dropped or damaged by water, contrary to the Auto Page OPERATIONS MANUAL. Or, if used with accessories not approved by Auto Page, which may have contributed to the defect. See note below regarding product installation**.
3. The purchaser’s remedies under this WARRANTY shall be limited to the repair or replacement of
electronic components only. THE FOLLOWING IS NOT COVERED: Damages or deterioration to cases, batteries, covers and cabinets; the cost of repairs, replacement and labor of which shall be borne by the purchaser even if occurring during the WARRANTY period.
4. Any equipment or parts which are claimed to be defective under this WARRANTY must be sent to
the Auto Page Service center with “proof of purchase” at the purchaser’s expense prior to such return, a Return Authorization Number should be obtained. Auto Page will return the equipment, charges prepaid. Warranty Service can be provided through the dealer where the equipment is originally purchased.
5. Any unexpired WARRANTY shall be applicable to equipment and parts in the possession of the
original purchaser only.
6. THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
7. Auto Page shall not be liable, under the foregoing WARRANTIES or otherwise, for: Any personal
injury of any kind to the purchaser, its employees or agents or anyone else whomsoever resulting directly or indirectly from the use or presence of the equipment or parts; Consequential damages of any kind; any inability of the purchaser to use the equipment.
The attached WARRANTY CARD is for your record. However, Auto Page reserves the right to request you to submit this WARRANTY CARD, which must have complete information to receive warranty service. Please keep this card in a secured place.
**IMPORTANT NOTE: Any damages to the alarm system resulting from an installation performed by anyone other than a professional installation technician
12
authorized by a dealer of Auto Page will void the product’s limited lifetime warranty.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service. Please keep this card in a secured place.
AUTOPAGE WARRANTY SERVICE CARD
Model: RF-420LCD
Serial # _______________
CUSTOMER TO COMPLETE DEALER TO COMPLETE
Mr./Mrs./Ms.
_______________________________ ________________________________ Your Name (Please Print) Company Name
_______________________________ ________________________________ Address Dealer’s Address
_______________________________ ________________________________ City, State, Zip Code City, State, Zip Code
_______________________________ ________________________________ Telephone Number Dealer’s Telephone Number
_______________________________ ________________________________ Year / Make / Model of Vehicle Date of Installation / Purchase
________________________________ Dealer’s Signature
“Proof of Purchase” which includes the store name and date of purchase must accompany all warranty returns.
It is the purchaser’s responsibility to keep this card for any future warranty service.
13
960 Knox Street Unit B
Torrance, California 90502
Main Office: 310-323-1800
Customer Service: 800-262-2527 Ext. 462
www.autopageusa.com
Loading...