Auto Page RF-310 User Manual

IS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY

RF-310

PROFESSIONAL VEHICLE SECURITY SYSTEM

OPERATION MANUAL

TRANSMITTER OPERATION:

Transmitter Button System Function Remark

Button – Button Button Button for 3 seconds

Button – Button

Button Button for 2 seconds

Button for 3 seconds

+ Button

Side button 2 nd Car Operation or

Arm / Lock door Arm and Delete Optional Sensor Press twice. Car Locator System in Armed. Panic function Press 3 seconds Disarm & Unlock Door

Two Steps Door Unlock & Disarm System

Car Locator Pop Trunk Release Press 2 seconds

Panic function Silent Arm / Disarm

Silent Arm / Disarm

Garage Door Opener

Press twice within 3 seconds.

If the H3/6 Gray Wire is not Trunk release Output (See Alarm Feature III-2)

Side Button Switching Code

ACTIVE ARMING – LOCK & ARM:

1. Press button on transmitter.

2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle doors will lock upon arming when interfaced with the security system.

Note: Defective sensor reminder: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. (See Feature “I - 3 Programming)

SILENT ARMING / DISARMING: Press the button on the transmitter to arm or disarm your security system with no chirp sound heard; arm / disarm confirmation will be through the vehicles parking lights only.

SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Press the button on the transmitter

twice within 3 seconds will arm the security system, by-pass the shock sensor or the optional sensor connected to 4 pin plug. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.

PASSIVE ARMING: (See Feature “II - 2” Programming)

Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle. (CONT. NEXT PAGE)

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed.

3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time.

PASSIVE DOOR LOCKING: (See Feature “II - 2” Programming)

The vehicle doors will automatically lock after passive arming cycle has been completed.

ACTIVE DISARMING – UNLOCK & DISARM:

1. Press the button on the transmitter.

2. The siren will chirp twice and parking lights will flash twice to indicate that the security system is now disarmed. The vehicle doors will unlock and disarm when interfaced with the security system.

TAMPER DISARMING: If the alarm is triggered; upon disarm the system, the siren will chirp 4 times and parking lights will flash 3 times. TWO STEP DOOR UNLOCK: (See Feature III – 2 Programming.) This feature will independently unlock the driver’s door only when disarming the security system. Pushing the

button on the transmitter a second time within 3 seconds will unlock the entire vehicle.

AUTOMATIC RE-ARM (See Feature “I - 2” Programming): If this feature is selected, the

security system will automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.

DISARMING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 10 seconds push and release the valet switch

The alarm will stop sounding and enter the disarm mode. You can now start and operate the

vehicle normally.

VALET MODE:

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however, the remote panic feature and remote door locks will remain operational.

Enter Valet Mode:

1. Turn the ignition to “ON” position.

2. Push and hold valet switch for 2 seconds or until the LED turns on. The LED will remain on as long as the system is in 'valet mode'.

Exit Valet Mode:

1. Return to normal operation, turn ignition 'ON'.

2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting the valet mode.

+ 5 hidden pages