AutoPage RF-305 Operation Manual

OPERATION INSTRUCTIONS

REMOTE CONTROL TRANSMITTER OPERATION

Your AutoPage Security System comes with two 5-button Remote Control
Transmitters that feature a sophisticated code hopping system that will prevent
illegal use of a code grabber with an attempt to record and steal your transmitter
codes.

LOCK – ARM & LOCK

To arm your Security System, press the LOCK button once. The siren will chirp
(1) time and the vehicles parking lights will flash (1) time indicating that the
Security System is now arme d. The vehicles doors will lock upon arming when
interfaced with the Security System.

UNLOCK – DISARM & UNLOCK

To disarm your Security System, press the UNLOCK button once. The siren will
chirp (2) times and the vehicles parking lights will flash (2) time s indicating that
the Security System is now disarmed. The vehicles doors will unlock upon
disarming when interfaced with the Security System.

DELETING THE ARM/DISARM CHIRP

When attempting to arm or disarm your Security System, you have the option of
tem porarily muting the siren chirp sound. To perform this function, simply
depress both LOCK & UNLOCK buttons on the Remote Control Transmitter at
the same time. No chirp sound will be heard, arm / disarm confirmation will be
through the vehicles parking lights only.

REMOTE PANIC FUNCTION

The Remote Control Transmitter may be used as a remote panic switch that will
activate the Security Systems siren and vehicles parking lights in case of an
emergency. To activate the PANIC function, press and hold the * button on the
Remote Control Transmitter for (3) seconds. The siren will sound and the
vehicles parking lights will flash continuously. To cancel the PANIC function,
press the lock / unlock button on the Remote Control Transmitter.

AUXILIARY FUNCTION ( OPTIONAL )

You may use the EXT1 button on your Remote Control Transmitter for a
separate function. For example, if your vehicle is equipped with an electronic
trunk release, the Security System can be interfaced with it and can electronically
release your trunk by pressing the EXT1 button for 2 seconds on the Remote
Control Transmitter.

REMOTE CONTROL TRANSMITTER PROGRAMMING

In the event, you should need to add or replace a Remote Control Transmitter, it
is important that you follow the instructions below.

Note: Each step must be performed within 10 seconds of the previous step

1. Enter:
a. Turn the vehicles ignition to the “ON” position
b. Push the valet switch 3 times. There will be 1 long chirp and 1 short chirp
c. You are now ready to program the Remote Control Transmitter(s).

otherwise the system will exit the programming mode.

2. Programming the Remote Control Transmitters:
a. Press any button on the first transmitter. There will be 1 short chirp.

b. Within 10 seconds push any button on the second transmitter. There

will be 2 short chirps.

3. Exit:
a. Turn the vehicles ignition to the “OFF” position, Or

b. Leave for 10 seconds; there will be 3 long chirps to confirm exit.

Note: The Security System will only retain the last 4 Remote Control

Transmitters programmed. If the Transmitter memory is exceeded, the
Security System will start deleting Transmitters from memory in
chronological order.

SECOND VEHICLE REMOTE TRANSMITTER PROGRAMMING

Your AutoPage Security Systems Remote Control Transmitter can be utilized to
control a second vehicle equipped with an RF-305 or RF-405. To program the
Remote Control Transmitter to a second vehicle, follow the instructions for
Remote Transmitter Programming. All programming parameters will be the same
except for the following:

1. Prior to pushing any button on the Remote Control Transmitter. Select the
Green side shift button first.

2. Once the Green side shift is pressed the LED on the Remote Control
Transmitter will illuminate for 3 seconds.

3. While the LED is illuminated, press any button on the Remote Control
Transmitter.

CHANGING THE REMOTE CONTROL TRANSMITTER BATTERY

The Remote Control Transmitters come with (1) miniature 12-volt battery. Under
normal use this battery should have a life of approximately one year. If you
should need to replace your battery you may want to return to your installing
dealer. You may also wish to change the battery by yourself. When purchasing
the battery be sure to purchase any of the following: GP23A, #EL12, #VR22 or
Radio Shack #23-144.

To replace the battery, carefully remove the case screw located on the bottom of
the Remote Control Transmitter where the key ring attaches to the case. Use a

miniature #1 Phillips head screwdriver!

After removing the screw, carefully pop open the plastic case. Before removing
the battery note the direction of its “+/-“ terminals. Install the new battery exactly
the same way using caution not to bend the battery contacts. Replace the case
cover and insert and tighten the screw. Do not over tighten! Test the Remote
Control Transmitter.

SYSTEM OPERATION
OVERRIDE FUNCTION

The OVERRIDE FUNCTION may be used if the Remote Control Transmitter is
lost or inoperative. To operate, enter the vehicle (alarm will sound), turn the
vehicles ignition to the “ON” position and push the valet/override switch until
alarm stops sounding. The alarm is disarmed & reset. Have your Remote Control
Transmitter serviced or replaced.

VALET FUNCTION

The alarm has a valet or stand-by mode that can be used when the vehicle is
being serviced or valet parked. To activate the valet, turn the vehicles ignition to
the “ON” position, then push and hold the valet/override switch for 2 seconds or
until the Security Systems LED turns ON solid. Turn the vehicles ignition to the
“OFF” position; your vehicle is now in valet mode. To reactivate, repeat the
above procedure noting the system LED will now turn OFF.

Note: If your vehicle has the Keyless Entry option installed, you can still lock

and unlock your doors with Remote Control Transmitter while in the
Valet Mode.

PASSIVE/MANUAL OPERATION

Manual Arming / Disarming is controlling your security system via the Remote
Control Transmitter. This Security System is equipped with an optional Passive
Arming feature, which allows the Security System to arm 30 seconds after the
last door is closed. Operation is as follows.

1. Turn the vehicles ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the Security Systems LED will flash fast for
30 seconds. If you re-open any door, the Security Systems LED will stop
flashing. It will begin flashing again once the vehicles door is closed.

3. After the 30 second timer has elapsed, the Security System will
automatically “ARM”. The siren will chirp (1) time and the vehicles parking
lights will flash (1) time.

Note: If the vehicles door locks have been interfaced to the Security System,

the doors will automatically lock after the passive arming cycle has
been completed. If this featur e is not desired, see your local dealer
and have the Security System re-programmed to eliminate passive
door locking.

AUTOMATIC REARMING (OPTIONAL)

If this feature is selected, the Security System will automatically re-arm itself 60
seconds after disarming with the Remote Control Transmitter. Automatic rearm
will cancel if any door is opened before the 60 second timer has elapsed.

IGNITION CONTROL DOOR LOCKS (OPTIONAL)

If the vehicles door locks have been interfaced to the Security System, the
Security System will automatically lock the vehicles doors when the ignition is
turned “ON” and unlock the vehicles doors when the ignition is turned “OFF”.

Note: If any door is open when the vehicles ignition is turned “ON”, the

Security System will not automatically lock the vehicles doors.

LED STATUS INDICATOR

1. LED OFF: Security System is disarmed

2. LED ON: Security System is in valet mode

3. LED FAST FLASHING: Automatic arming timer is counting down

4. LED FLASHING: Security System is armed

CHIRP AND PARKING LIGHT FLASH INDICATORS

1. 1 Chirp & 1 light flash = Security System is armed

2. 2 Chirps & 2 light flashes = Security System is disarmed

3. 4 Chirps & 3 light flashes = Security System breach or intrusion in your
absence.

PATHWAY ILLUMINATION (OPTIONAL)

When disarming the Security System, the vehicles parking lights will stay on
illuminating your pathway to the vehicle. The vehicles parking lights will stay on
for 30 seconds or until the vehicles ignition is turned to the “ON” position.

30 SECOND ARMING DELAY

After arming your vehicle with the Remote Control Transmitter, the siren will chirp
(1) time and the vehicles parking lights will flash (1) time. The Security System
will instantly go into a 30-second standby mode to monitor all Security System
functions. After the 30 seconds has elapsed, the Security System is now fully
armed. If a door is opened or if you have a faulty sensor, the Security System will
give a warning by chirping the siren (3) times.

SHOCK SENSOR

Your AutoPage Security System includes a dual zone shock sensor designed to
trigger the alarm from impact to the vehicle, such as a window being broken. If
sensitivity adjustment should become necessary consult your local Authorized
Dealer. Do not attempt to do this on your own!

STARTER DISABLE FEAT URE (OPTIONAL)

If installed with your Security System, this feature is designed to prevent a thief
from starting your vehicle once they have broken in to it.

SECOND VEHICLE OPERATION

Your AutoPage Security Systems Remote Control Transmitter can be utilized to
control a second vehicle equipped with an RF-305 or RF-405. If your Remote
Control Transmitter is programmed to a second vehicle, the Remote Control
Transmitter will operate as follows:

1. Push the Green side shift button on the right side of the Remote Control
Transmitter, the LED will illuminate for 3 seconds.

2. While the LED is illuminated, push the desired button operation. For
Example: To Arm the second vehicle, simply push the Green side shift
button once then push the Lock/Arm button while the LE D is illuminated.

1815 West 205th Street

Suite 101

Torrance, California 90501-1525

Main Office: 310-618-2002

RF305

PROFESSIONAL VEHICLE SECURITY

OPERATIONS MANUAL

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION

ONLY